15238.100_102113.19_Plastic_Toilet_Compartments.pdf

15238.100/09-18 PLASTIC TOILET COMPARTMENTS 102113.19 - 1

SECTION 102113.19

PLASTIC TOILET COMPARTMENTS

PART 1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Solid plastic toilet compartments.

1.2 RELATED REQUIREMENTS

1.2.1 Section 061000 - Rough Carpentry: Blocking and supports.

1.3 REFERENCE STANDARDS

1.3.1 ASTM A666 - Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar; 2015.

1.3.2 ASTM E84 - Standard Test Method for Surface Burning Characteristics of Building Materials;

2016.

1.3.3 NFPA 286 - Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth; 2015.

1.4 ADMINISTRATIVE REQUIREMENTS

1.4.1 Coordination: Coordinate the work with placement of support framing and anchors in walls and ceilings.

1.5 SUBMITTALS

1.5.1 See Section 013000 - Administrative Requirements, for submittal procedures.

1.5.2 Product Data: Provide data on panel construction, hardware, and accessories.

1.5.3 Shop Drawings: Indicate partition plan, elevation views, dimensions, details of wall supports, door swings.

PART 2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Solid Plastic Toilet Compartments:

2.1.1.1. All American Metal Corp - AAMCO; _______: www.allamericanmetal.com/#sle.

2.1.1.2. Ampco Products, Inc; ______: www.ampco.com/#sle.

2.1.1.3. Inpro; Endurant Toilet Partitions: www.inprocorp.com/#sle.

2.1.1.4. Metpar Corp; _____: www.metpar.com/#sle.

2.1.1.5. Scranton Products (Santana/Comtec/Capital); ______: www.scrantonproducts.com/#sle.

2.1.1.6. Substitutions: Section 016000 - Product Requirements.

2.2 PLASTIC TOILET COMPARTMENTS

2.2.1 Solid Plastic Toilet Compartments: Factory fabricated doors, pilasters, and divider panels made of solid molded high density polyethylene (HDPE), tested in accordance with NFPA 286;

floor-mounted headrail-braced.

2.2.1.1. Color: As selected by Architect from manufacturers standard selection..

2.2.1.2. Doors:

(2.2.1.2.1) Thickness: 1 inch (25 mm).

(2.2.1.2.2) Width: 24 inch (610 mm).

(2.2.1.2.3) Width for Handicapped Use: 36 inch (915 mm), out-swinging.

(2.2.1.2.4) Height: 55 inch (1397 mm).

2.2.1.3. Panels:

(2.2.1.3.1) Thickness: 1 inch (25 mm).

(2.2.1.3.2) Height: 55 inch (1397 mm).

2.2.1.4. Pilasters:

(2.2.1.4.1) Thickness: 1 inch (25 mm).

(2.2.1.4.2) Width: As required to fit space; minimum 3 inch (76 mm).

15238.100/09-18 PLASTIC TOILET COMPARTMENTS 102113.19 - 2

PART 3 EXECUTION

3.1 EXAMINATION

3.1.1 Verify that field measurements are as indicated.

3.1.2 Verify correct spacing of and between plumbing fixtures.

3.1.3 Verify correct location of built-in framing, anchorage, and bracing.

3.2 INSTALLATION

3.2.1 Install partitions secure, rigid, plumb, and level in accordance with manufacturer's instructions.

3.2.2 Maintain 3/8 inch to 1/2 inch (9 mm to 13 mm) space between wall and panels and between wall and end pilasters.

3.2.3 Attach panel brackets securely to walls using anchor devices.

3.2.4 Attach panels and pilasters to brackets. Locate head rail joints at pilaster center lines.

3.2.5 Field touch-up of scratches or damaged finish will not be permitted. Replace damaged or scratched materials with new materials.

3.3 TOLERANCES

3.3.1 Maximum Variation From True Position: 1/4 inch (6 mm).

3.3.2 Maximum Variation From Plumb: 1/8 inch (3 mm).

3.4 ADJUSTING

3.4.1 Adjust and align hardware to uniform clearance at vertical edge of doors, not exceeding 3/16 inch (5 mm).

3.4.2 Adjust hinges to position doors in partial opening position when unlatched. Return out-swinging doors to closed position.

3.4.3 Adjust adjacent components for consistency of line or plane.

END OF SECTION