Exhibit_A_-_Technical_Requirements.pdf

Exhibit A SPRBL1-19-Q0118 Page 1 of 8 Issue: 02 FEB 2019

TECHNICAL REQUIREMENTS

Acquisition of the TS-3920C/ASM Computer Test Set Advanced Flight Control Computer Kit (AFCC)

TS-3920C Computer Test Set and

End To End System BrainPak

Exhibit A SPRBL1-19-Q0118 Page 2 of 8

TABLE OF CONTENTS

APPLICABLE DOCUMENTS

CONFIGURATION BASELINE

Obsolescence Reporting.................................................................... Error! Bookmark not defined.

Part Revisions

Special Instructions

Value Engineering Acceptance Test Procedures……………………………………………………………………….. 5

PACKAGING

Wood Packing Material

Military Packaging

CONTRACT SECURITY

CONTRACT DATA REQUIREMENT LIST (CDRL) DD 1423-1

DELIVERIES

Exhibit A SPRBL1-19-Q0118 Page 3 of 8

APPLICABLE DOCUMENTS

Military and Federal Standards MIL-STD-129R Military Marking for Shipment and Storage MIL-STD-130N(1) Identification Marking of U.S. Military Property MIL-STD-2073-1E with change 3 Standard Practice For Military Packaging

Military and Federal Specifications

Other Documents DI-MISC-80711A Technical Report – Configuration Management

Commercial Documents ASTM D 3958-15 Standard Practice for Commercial Packaging ISPM Number 15 Regulation of Wood Packaging Material in International Trade (2009) 10-0113-53 UxValidator AFCC SCATS Check Procedure 10-0121-31 UxValidator Section 4.1 Self-Test Procedure

Security Documents

AT/OPSEC

CONFIGURATION BASELINE

The applicable Configuration Baselines (CB), for the listed Configuration Item (CI) and/or Computer Software Configuration Item (CSCI), are as listed in the table below.

NSN Nomenclature Part Numbers/Drawings 6625-01-529-3346 TS-3920C/ASM Computer Test Set 05-0330-07 6625-01-549-5996 TS-3920C Computer Tester (UxValidator) 03-1217-02 4920-01-585-8568 Advanced Flight Control Computer BrainPak Kit 09-1009-03 5998-01-552-3973 Circuit Card Assembly Stabilator System End to End BrainPak 02-0819-08

Part Revisions The Government shall be notified of any changes in parts to manufacture these items (Configuration Control/Management) per CDRL DD Form 1423 for DI-MISC-80711A. The Government does not have to accept items that have configuration changes not approved by the procuring Government activity.

Obsolescence Reporting The contractor shall provide source data that will enable the identification, forecasting and management of piece part obsolescence impacts and mitigations. The DMSMS data shall be provided in accordance with the CDRL (DD Form 1423) for DI-PSSS-81656B.

Ozone Depleting Chemicals There are no Ozone Depleting Chemicals used in these items.

Year 2000 Year 2000 (Y2K) does not affect any of these items.

Exhibit A SPRBL1-19-Q0118 Page 4 of 8

Special Instructions

IUID:

All items shall have an IUID assigned and marked in a conspicuous area of the item so as to not interfere with usage. IUID shall be IAW DFARS 252.211-7003 Item Unique Identification and Valuation.

IUID shall include but not be limited to NSN, Serial Number, part number and nomenclature. Marking shall be permanent Human Readable characters per MIL-STD-130N (1). Symbology markings and the order of priority for marking the hardware shall be in accordance with MIL-STD-130 N (1). First priority is the 2D data matrix symbol (machine readable) IUID is the minimum requirement when there are severe space limitations. The second priority is the human readable characters. The third priority is the Linear Bar Code.

Requirements for Value Engineering. The submission of VECPs is encouraged to eliminate unnecessary requirements, reduce costs, and improve functionality of Team Command, Control, Communications, Computers, Combat, Intelligence, Surveillance and Reconnaissance (C5ISR) managed weapon systems.

VECPs can increase the value of delivered products and services and improve contractor profit. FAR clause 52.248-1 is incorporated by reference.

Value Engineering Information. To obtain more information about Value Engineering teaming within C4ISR, contact the Value Concepts Office at:

HEADQUARTERS U.S. ARMY CECOM LCMC

ATTN: AMSEL-LCL-EIE (Value Concepts Office)

6001 COMBAT DRIVE

ABERDEEN PROVING GROUND, MARYLAND 21005-1845

Phone: 443-861-5415

Acceptance Test Procedures. One hundred percent (100%) Acceptance testing shall be performed during the contract IAW the Ultrax Test Procedures:

10-0121-31 UxValidator Computer Test Set Acceptance Test Procedure 10-0113-53 UxValidator AFCC SCATS Check Procedure 02-0819-08 Stabilator System End to End BrainPak Acceptance Test Procedure

Electro-Static Discharge Labels: All items shall have an ESDS caution note and symbol per MIL-STD-130N with change 1 paragraph 5.9 on the item as required. The caution note and symbol shall be in a location readily visible to personnel that does not interfere with the normal operation of the item or obstruct any other markings as required by MIL-STD-130N with change 1 and the procurement contract.

Electro-Static Discharge Sensitive (ESDS) Warranty Items. All ESDS warranty and non-warranty items returned for repair shall insure that the ESDS caution note and symbol per MIL-STD-130N with change 1 paragraph 5.9 on the item are still legible after repair as required. The caution note and symbol shall be in a location readily visible to personnel that does not interfere with the normal operation of the item or obstruct any other markings as required by MIL-STD-130N with change 1 and the procurement contract.

PACKAGING

Wood Packing Material: Wood Packaging Material in compliance with ISPM-15, Regulation of Wood Packaging Material in International trade, is applicable. Marking shall be in accordance with MIL-STD-129R.

Exhibit A SPRBL1-19-Q0118 Page 5 of 8

RFID Requirements shall be in accordance the Section ‘F’ clause, DFARS 252.211-7006, of the contract.

Wood Packaging Material (WPM) shall meet the requirements below.

Nonmanufactured soft and hard wood materials identified as intended for use in the construction of wooden pallets, wood containers, and blocking and bracing shall be heat treated (HT) to a core temperature of 56 degrees Centigrade for 30 minutes, certified, and marked by an accredited agency recognized by the American Lumber Standards Committee (ALSC) in accordance with their Nonmanufactured Wood Packing Policy and Nonmanufactured Wood Packing Enforcement Regulations, both dated 30 May 2001.

Packaging shall be in accordance with MIL-STD-2073-1E w/Chg 3, Level of Pack (LPK), B, and Quantity Unit Pack (QUP): 001. I attached edited DS7029-DS7033 with packaging requirement codes.

New WPM: New WPM acquired by DoD Components to include contractors, shall be compliant with International Standards for Phytosanitary Measures (ISPM) Number 15, Regulation of Wood Packaging Material in International Trade (2009), United Nations (UN), Food and Agriculture Organization (FAO).

Within the United States, the DoD Components and contractors shall also adhere to the American Lumber Standard Committee (ALSC) and the National Wood Pallet and Container Association (NWPCA), guidelines on “Pest Free” WPM. In overseas areas, DoD Components shall procure all WPM in compliance with host nation implementation of UN IPPC Phytosanitary standards, if such standards have been implemented.

Handling, Storage, Preservation, Packaging and Shipping. The contractor shall establish, maintain, control and be responsible for the handling, storage, preservation, packaging, and shipping to protect the quality of the materials and to prevent damage from loss, deterioration, degradation, or substitution of products.

Exhibit A SPRBL1-19-Q0118 Page 6 of 8

DS7029 - DS7033

NSN Prot Req PKG-REF or SPI LPK QUP ICQ Special Markings

Pkg J. J J J J J J J J J Reqmt I. II. III. IV. V. VI. VII. VII.a IX X Codes (MP) (CD) (PM) (WM) (CD) (CT) (UC) (IC) (PK) (SM) 4920-01-585-8568 Military MIL-STD-2073-1E w/Chg 3 B 001 - 31 1 00 00 GT B ED 00 - 00 BC 6625-01-529-3346 Military MIL-STD-2073-1E w/Chg 3 B 001 - 10 1 00 00 00 0 ED 00 - 00 BC 6625-01-534-5996 Military MIL-STD-2073-1E w/Chg 3 5998-01-552-3973 Military MIL-STD-2073-1E w/Chg 3

Exhibit A SPRBL1-19-Q0118 Page 7 of 8

CONTRACT SECURITY

AT-OPSEC form required.

CONTRACT DATA REQUIREMENT LIST (CDRL) DD 1423-1

See PWS.

Deliveries. The Contractor shall prepare and commence production deliveries as required no later than 90 days after contract award for the NSNs on contract: (1) TS-3920C/ASM Computer Test Set, NSN: 6625-01- 529-3346 (2) TS-3920C Computer Tester, NSN: 6625-01-534-5996, (3) AFCC Kit, NSN: 4920-01-585- 8568 and (4) Stabilator System End to End BrainPak, NSN: 5998-01-552-3973. See Section F for the Solicitation.

The Contractor shall return maintenance items as required no later than 45 days after receipt of item(s) for the NSNs on contract: (1) 6625-01-529-3346 TS-3920C/ASM Computer Test Set, (2) 6625-01-534-5996 TS-3920C Computer Tester and 4920-01-585-8658 AFCC Kit. See Section F for the Solicitation.

Exhibit A SPRBL1-19-Q0118 Page 8 of 8