4' -0

'-0

'-0

'-0

'-0

'-0

'-0

'-0

'-0

'-0

'-0

'-0

'-0

0' -0

201'-0"

4' 0"

4' 0"

Ne w Ro of Cr ick et s

2" ta ll to

0" in 4' rid ge

Ne w Ro of Dr ai ns

Re pl ac e ex ist in g Ro of Ha tc h

In st al ln ew

Ro of

Ha tc h

0'

0"

16'0"

Ne w De ns gl as sS he at hi ng

Ne w

TP

O Ro of in g in st al le d.

Lo ad in g Do ck Ro of

Re m ov e an d in st al ln ew

M et al Ca p Fl as hi ng at al l

Pa ra pe tw al ll oc at io ns

Bl dg .6

Ca m p Sa n Lu is Ob isp o

Camp San Luis Obispo, Bldg. 632 San Luis Obispo, CA

June 2021

PART 1 GENERAL

1.01 DESCRIPTION

A. The Camp San Luis Obispo Project is located at 10 Sonoma Ave. in San Luis Obispo, CA. The Contracting Officer’s Representative (COR), Project Manager is David Gonzales the COR he may be reached via email at David.gonzales167.nfg@mail.mil. or by telephone at 805-594-6577. The Military Department shall provide a Job walk date with the formal solicitation documents.

B. The project consists of installing Versico’s VersiWeld (TPO) Mechanically Attached Roofing System or a proposed equivalent (All equivalents shall be required to be approved by the COR) as outlined below:

Apply the VersiWeld Mechanically Attached Roofing System over the existing 45-mil TPO and 1” Polyiso roof system. All existing Polyiso and/or coverboard to be inspected and replaced as needed before new membrane is installed.

1.02 EXTENT OF WORK

A. Provide all labor, material, tools, equipment, and supervision necessary to complete the installation of the VersiWeld reinforced TPO (Thermoplastic Polyolefin) membrane Mechanically-Fastened Roofing System or equivalent including flashings and insulation as specified herein and as indicated on the drawings in accordance with the manufacturer's most current specifications and details.

B. The Contractor shall be fully knowledgeable and a Certified installer of the product by the Manufacturer of the product. It is assumed the Contractor is fully aware of all requirements of the contract documents and shall make themselves aware of all job site conditions that will affect their work.

C. The Contractor shall confirm all given information and notify the building owner, prior to bid, of any conflicts that will affect their cost proposal.

D. Any contractor who intends to submit a bid using a roofing system other than the approved manufacturer must submit for pre-qualification in writing fourteen (14) days prior to the bid date. Any contractor who fails to submit all information as requested will be subject to rejection.

1.03 SUBMITTALS

A. Prior to starting work, the roofing contractor must submit the following:

1. Shop drawings showing layout, details of construction and identification of materials.

2. Sample of the manufacturer's Membrane System Warranty. Any proposed equivalent shall match or exceed the specified product warranty.

3. Submit a letter of Certification from the manufacturer which Certifies the roofing contractor is authorized to install the manufacturer's roofing system and lists foremen who have received training from the manufacturer along with the dates training was received and provide a certificate from the Manufacturer listing the individual’s name.

4. Certification from the membrane manufacturer indicating the fasteners are capable of providing a static backout resistance of 10 inch pounds minimum is required.

5. Certification from the membrane manufacturer indicating the membrane thickness over the reinforcing scrim (top ply membrane thickness) is nominal .15-mil or thicker.

mailto:David.gonzales167.nfg@mail.mil

6. Certification of the manufacturer's warranty reserve.

B. Upon completion of the installed work, submit copies of the manufacturer's final inspection to the specifier prior to the issuance of the manufacturer's warranty.

1.04 PRODUCT DELIVERY, STORAGE AND HANDLING

A. Deliver materials to the job site in the manufacturer's original, unopened containers or wrappings with the manufacturer's name, brand name and installation instructions intact and legible. Deliver in sufficient quantity to permit work to continue without interruption.

B. Comply with the manufacturer's written instructions for proper material storage.

1. Store VersiWeld membrane in the original undisturbed plastic wrap in a cool, shaded area and cover with light-colored, breathable, waterproof tarpaulins. VersiWeld membrane that has been exposed to the elements for approximately 7 days must be prepared with Versico Weathered Membrane Cleaner prior to hot air welding.

2. Store curable materials (adhesives and sealants) between 60°F and 80°F in dry areas protected from water and direct sunlight. If exposed to lower temperature, restore to 60°F minimum temperature before using.

3. Store materials containing solvents in dry, well ventilated spaces with proper fire and safety precautions. Keep lids on tight. Use before expiration of their shelf life.

C. Insulation must be on pallets, off the ground and tightly covered with waterproof materials.

D. Any materials which are found to be damaged shall be removed and replaced at the applicator's expense.

1.05 WORK SEQUENCE

A. Schedule and execute work to prevent leaks and excessive traffic on completed roof sections. Care should be exercised to provide protection for the interior of the building and to ensure water does not flow beneath any completed sections of the membrane system.

B. Do not disrupt activities in occupied spaces.

1.06 USE OF THE PREMISES

A. Before beginning work, the roofing contractor must secure approval from the building owner's representative for the following:

1. Areas permitted for personnel parking.

2. Access to the site.

3. Areas permitted for storage of materials and debris.

4. Areas permitted for the location of cranes, hoists and chutes for loading and unloading materials to and from the roof.

B. Interior stairs or elevators may not be used for removing debris or delivering materials, except as authorized by the COR.

1.07 EXISTING CONDITIONS

If discrepancies are discovered between the existing conditions and those noted on the drawings, immediately notify the owner's representative by phone and solicit the manufacturer's approval prior to commencing with the work.

Necessary steps shall be taken to make the building watertight until the discrepancies are resolved.

1.08 PRE-CONSTRUCTION JOBWALK

A. Prior to bid submittal, the roofing contractor should schedule a job site inspection to observe actual conditions and verify all dimensions on the roof. The Military Department shall provide a formal Job walk date with the Solicitation documents.

B. Any conditions which are not shown on the shop drawings should be indicated on a copy of the shop drawing and included with bid submittal if necessary to clarify any conditions not shown.

1.09 TEMPORARY FACILITIES AND CONTROLS

A. Temporary Utilities:

1. Water and power for construction purposes are available at the site and will be made available to the roofing contractor.

2. Contractor to provide all hoses, valves and connections for water from source designated by the owner when made available.

3. When available, electrical power should be extended as required from the source. Contractor to provide all trailers, connections and fused disconnects.

B. Temporary Sanitary Facilities

Sanitary facilities will not be available at the job site. The roofing contractor shall be responsible for the provision and maintenance of portable toilets or their equal.

C. Building Site:

1. The roofing contractor shall use reasonable care and responsibility to protect the building and site against damages. The contractor shall be responsible for the correction of any damage incurred as a result of the performance of the contract.

2. The roofing contractor shall remove all debris from the job site in a timely and legally acceptable manner so as to not detract from the aesthetics or the functions of the building.

D. Security:

Obey the owner's requirements for personnel identification, inspection and all other security measures.

1.10 JOB SITE PROTECTION

A. The roofing contractor shall adequately protect building, paved areas, service drives, lawn, shrubs, trees, etc.

from damage while performing the required work. Provide canvas, boards and sheet metal (properly secured) as necessary for protection and remove protection material at completion. The contractor shall repair or be responsible for costs to repair all property damaged during the roofing application.

B. During the roofing contractor's performance of the work, the building owner will continue to occupy the existing building. The contractor shall take precautions to prevent the spread of dust and debris, particularly where such material may sift into the building. The roofing contractor shall provide labor and materials to construct, maintain and remove necessary temporary enclosures to prevent dust or debris in the construction area(s) from entering the remainder of the building.

C. Do not overload any portion of the building, either by use of or placement of equipment, storage of debris, or storage of materials.

D. Protect against fire and flame spread. Maintain proper and adequate fire extinguishers.

E. Take precautions to prevent drains from clogging during the roofing application. Remove debris at the completion of each day's work and clean drains, if required. At completion, test drains to ensure the system is free running and drains are watertight. Remove strainers and plug drains in areas where work is in progress. Install flags or other telltales on plugs. Remove plugs each night and screen drain.

F. Store moisture susceptible materials above ground and protect with waterproof coverings.

G. Remove all traces of piled bulk materials and return the job site to its original condition upon completion of the work.

1.11 SAFETY

The contractor shall be responsible for all means and methods as they relate to safety and shall comply with all applicable local, state and federal requirements that are safety related. Safety shall be the responsibility of the contractor. All related personnel shall be instructed daily to be mindful of the full time requirement to maintain a safe environment for the facility's occupants including staff, visitors, customers and the occurrence of the general public on or near the site.

1.12 WORKMANSHIP

A. Applicators installing new roof, flashing and related work shall be factory trained and approved by the manufacturer they are representing.

B. All work shall be of highest quality and in strict accordance with the manufacturer's published specifications and to the building owner's satisfaction.

C. There shall be a designated in advance of the job start named supervisor on the job site at all times while work is in progress.

1.13 QUALITY ASSURANCE

A. The VersiWeld Roofing System must achieve a UL Class A.

B. Contractor to provide the specified roofing assembly to have been successfully tested by a qualified testing agency to resist the design uplift pressures calculated according to

ANSI/SPRI WD-1 "Wind Design Standard Practice for Roofing Assemblies” American Society of Civil Engineers (ASCE 7) International Building Code (IBC) DORA (Directory of Roof Assemblies)

C. The membrane must be manufactured by the material supplier. Manufacturer’s supplying membrane made by others are not acceptable.

D. Unless otherwise noted in this specification, the contractor must strictly comply with the manufacturer's current specifications and details.

E. The roofing system must be installed by an applicator authorized and trained by the manufacturer in compliance with shop drawings as approved by the manufacturer. The roofing applicator shall be thoroughly experienced and upon request be able to provide evidence of having at least five (5) years successful experience installing single-ply TPO roofing systems and having installed at least one (1) roofing application or several similar systems of equal or greater size within one year.

F. Provide adequate number of experienced workmen regularly engaged in this type of work who are skilled in the application techniques of the materials specified. Provide at least one thoroughly trained, certified and experienced superintendent on the job at all times roofing work is in progress.

G. There shall be no deviations made from this specification or the approved shop drawings without the prior written approval of the specifier. Any deviation from the manufacturer's installation procedures must be supported by a written certification on the manufacturer's letterhead and presented for the specifier's consideration.

H. The VersiWeld TPO White membrane meets CRRC (Cool Roof Rating Council) for reflectance and emittance. When tested in accordance with ASTM C1549, the VersiWeld White material has an initial solar reflectance of 0.79 and a 3-year aged reflectance of 0.70. The material has also been tested for emittance in accordance with ASTM C1371; an initial emittance of 0.90 and a 3-year aged emittance of 0.86 were achieved.

I. The VersiWeld White TPO membrane meets the emittance requirements set forth by the USGBC (U. S.

Green Building Council) for their LEED (Leadership in Energy and Environmental Design) Program. The VersiWeld White TPO material has an emittance of 0.90 (when tested in accordance with ASTM E408) and an SRI (solar reflectance index) of 99 (calculated using ASTM E 1980).

J. Upon completion of the installation, the applicator shall arrange for an inspection to be made by a non-sales technical representative of the membrane manufacturer in order to determine whether or not corrective work will be required before the warranty will be issued. Notify the building owner seventy-two (72) hours prior to the manufacturer's final inspection. A letter of compliance shall be issued by the manufacturer upon satisfactorily meeting the installation requirements.

1.14 JOB CONDITIONS, CAUTIONS AND WARNINGS

Refer to Versico's VersiWeld Roofing System specification for General Job Site Considerations.

A. Safety Data Sheets (SDS) must be on location at all times during the transportation, storage and application of materials.

B. When positioning membrane sheets, exercise care to locate all field splices away from low spots and out of drain sumps. All field splices should be shingled to prevent bucking of water.

C. When loading materials onto the roof, the Versico Authorized Roofing Contractor must comply with the requirements of the building owner to prevent overloading and possible disturbance to the building structure.

D. Proceed with roofing work only when weather conditions are in compliance with the manufacturer's recommended limitations, and when conditions will permit the work to proceed in accordance with the manufacturer's requirements and recommendations.

E. Proceed with work so new roofing materials are not subject to construction traffic. When necessary, new roof sections shall be protected and inspected upon completion for possible damage.

F. Provide protection, such as 3/4 inch thick plywood, for all roof areas exposed to traffic during construction.

Plywood must be smooth and free of fasteners and splinters.

G. The surface on which the insulation or roofing membrane is to be applied shall be clean, smooth, dry, and free of projections or contaminants that would prevent proper application of or be incompatible with the new installation, such as fins, sharp edges, foreign materials, oil and grease.

H. New roofing shall be complete and watertight at the end of the work day.

I. Contaminants such as grease, fats and oils shall not be allowed to come in direct contact with the roofing membrane.

1.15 WARRANTY

A. Provide manufacturer’s 30 year Membrane Material Only Warranty. The maximum wind speed coverage shall be peak gusts of 55 MPH measured at 10 meters above ground level. Certification is required with bid submittal indicating the manufacturer has reviewed and agreed to such wind coverage.

B. Contractor to provide a certification of acceptance from the manufacturer validating the installation is compliant with the Manufacturers’ requirements for proper installation.

PART 2 PRODUCTS

2.01 GENERAL

A. All components of the specified roofing system shall be products of Versico or accepted by Versico as compatible .Acceptance by Manufacturer shall be in a written document.

B. All products (including insulation, fasteners, fastening plates, prefabricated accessories and edgings) must be manufactured and/or supplied by the roofing system manufacturer and covered by the warranty.

2.02 MEMBRANE

Furnish VersiWeld 80-mil thick white reinforced TPO (Thermoplastic Polyolefin) membrane as needed to complete the roofing system. Membrane thickness over the reinforcing scrim (top-ply thickness) shall be nominal .015-mil or thicker. Membrane sheets in rolls 12', 10' or 8' wide by 100' long.

2.03 INSULATION/UNDERLAYMENT

A. When applicable, insulation shall be installed in multiple layers. The first and second layer of insulation shall be mechanically fastened to the substrate in accordance with the manufacturer's published specifications.

B. Insulation, if needed, shall be Polyiso to match existing as supplied by Versico. Minimum R-value required is to match existing.

1. Versico Versicore MP-H Polyiso – A foam core insulation board covered on both sides with a medium weight fiber-reinforced felt facer meeting ASTM C 1289-06, Type II, Class 1, Grade 2 (20 psi) or Grade 3 (25 psi). The product is available in 4’ x 8’ standard size with a thickness from 1 to 4 inches. 4’ x 4’ tapered panels are also available.

2. Dens Deck Cover Board –gypsum core that incorporates glass-mat facings on the top and bottom side for use as a cover board. 5/8” X 4’ x 8’ size boards.

2.04 ADHESIVES AND CLEANERS

All products shall be furnished by Versico and specifically formulated for the intended purpose.

A. Cut-Edge Sealant: A white or clear colored sealant used to seal cut edges of reinforced VersiWeld membrane. A coverage rate of approximately 225 - 275 linear feet per squeeze bottle can be achieved when a 1/8" diameter bead is applied.

B. Water Cut-Off Mastic: Used as a mastic to prevent moisture migration at drains, compression terminations and beneath conventional metal edging (at a coverage rate of approximately 10' per tube or 100' per gallon).

C. Universal Single-Ply Sealant: A 100% solids, solvent free, voc free, one part polyether sealant that provides a weather tight seal to a variety of building materials. It is white in color and is used for general caulking such as above termination bars and metal counter flashings and at scuppers.

D. Weathered Membrane Cleaner: Used to prepare membrane for heat welding that has been exposed to the elements or to remove general construction dirt at an approximate coverage rate of 400 square feet per gallon (one surface).

E. TPO Low VOC Primer:: A solvent-based, low solids primer used to prepare the surface of VersiWeld Membrane prior to application of Pressure-Sensitive Coverstrip and TPO Pressure-Sensitive RUSS. This low VOC product is ideal for use in states where environmental issues are a concern.

F. CAV-GRIP 3V Low-VOC Aerosol Contact Adhesive/Primer: a low-VOC, methylene chloride-free adhesive that can be used for a variety of applications including: bonding VersiWeld membrane to various surfaces, enhancing the bond between Versico’s VapAir Seal 725TR and various substrates, priming unexposed asphalt prior to applying Flexible DASH Adhesive and for adhering VersiGard FleeceBACK and VersiGard EPDM membrane to vertical walls. Coverage rate is approximately 2,000-2,500 sq. ft. per 40 lb.

cylinder and 4,000-5,000 sq. ft. per 85 lb. cylinder as a primer, in a single-sided application and 750 sq. ft.

per 40 lb. cylinder and 1,500 sq. ft. per 85 lb. cylinder as an adhesive for vertical walls, in a double-sided application.

2.05 FASTENERS AND PLATES

To be used for mechanical attachment of insulation and to provide additional membrane securement:

A. HPV Fasteners (Insulation and/or coverboard attachment only): a threaded, #14 fastener with a #3 phillips drive used with steel and wood roof decks.

B. HPVX Fasteners (Insulation, coverboard and membrane attachment): A heavy duty #15 threaded fastener with a #3 phillips drive used for membrane or insulation securement into steel, wood plank or minimum 15/32 inch thick plywood when increased pullout resistance is desired.

C. HPVX Plates: A 2-3/8” diameter metal barbed fastening plate used with Versico HPVX Fasteners for membrane securement. .

D. Insulation/coverboard Fastening Plates: A nominal 3 inch diameter plastic or metal plate used for insulation/coverboard attachment.

2.06 METAL EDGING AND MEMBRANE TERMINATIONS

A. General: All metal edging s shall be tested and meet ANSI/SPRI ES-1 standards and comply with International Building Code.

B. Drip Edge: A metal edge system with a 22 or 24 gauge continuous anchor cleat and .032 inch thick aluminum or 24 gauge steel fascia. Metal fascia color shall be as designated by the Owner's Representative.

C. VersiTrim Coping: Existing coping metal to remain in place.

D. Termination Bar: A 1” wide and .098” thick extruded aluminum bar pre-punched 6” on center; incorporates a sealant ledge to support Lap Sealant and provide increased stability for membrane terminations.

2.07 WALKWAYS

Protective surfacing for roof traffic shall be VersiWeld TPO Walkway Rolls installed per manufacturer’s requirements or concrete pavers loose laid over an approved slip sheet (pavers not recommended for slopes greater than 2” in 12”).

PART 3 EXECUTION

3.01 GENERAL

A. Comply with the manufacturer's published instructions for the installation of the membrane roofing system including proper substrate preparation, jobsite considerations and weather restrictions.

B. Position sheets to accommodate contours of the roof deck and shingle splices to avoid bucking water.

3.02 INSULATION PLACEMENT AND ATTACHMENT

A. Existing insulation and/or coverboard to remain in place. Existing insulation and/or coverboard to be inspected and replaced as needed before new membrane is installed. Install insulation or membrane underlayment over the substrate with boards butted tightly together with no joints or gaps greater than 1/4 inch. Stagger joints both horizontally and vertically if multiple layers are provided.

B. Secure insulation to the substrate with the required Versico fasteners and plates in accordance with manufacturers specifications.

3.03 MEMBRANE PLACEMENT AND ATTACHMENT

A. Existing membrane to be relief cut in large x’s at approx. 1 per 100 sq. ft.

B. Unroll and position membrane. Provide and secure both perimeter and field membrane sheets in accordance with the manufacturer's most current specifications and details.

C. Secure the membrane with the required Versico Fasteners and Plates spaced a maximum of 12 inches on center depending or project conditions (centered over the pre-printed marks approximately 1-1/2 inches from the edge of the membrane sheet).

D. Install adjoining membrane sheets in the same manner in accordance with the manufacturer's specifications.

3.04 MEMBRANE HOT AIR WELDING PROCEDURES

A. Hot air weld the VersiWeld membrane using an Automatic Hot Air Welding Machine or Hot Air Hand Welder in accordance with the manufacturer's specifications. At all splice intersections, roll the seam with a silicone roller immediately after welder crossed the membrane step-off to ensure a continuous hot air welded seam.

Note: When using 60-mil thick or thicker membrane, all splice intersections shall be overlaid with VersiWeld non-reinforced flashing or TPO T-Joint covers.

B. Probe all seams once the hot air welds have thoroughly cooled (approximately 30 minutes).

C. Repair all seam deficiencies the same day they are discovered.

D. Apply Cut Edge Sealant on all cut edges of reinforced membrane (where the scrim reinforcement is exposed) after seam probing is complete. Cut edge sealant is not required on vertical splices.

3.06 FLASHING

A. All existing flashings must be cut out and removed and replaced with new flashing.

B. Flashing of parapets, curbs, expansion joints and other parts of the roof must be performed using VersiWeld reinforced membrane. VersiWeld non-reinforced membrane can be used for flashing pipe penetrations, Sealant Pockets, scuppers, as well as inside and outside corners when the use of pre-fabricated accessories is not feasible.

C. Follow manufacturer's typical flashing procedures for all wall, curb, and penetration flashing including metal edging/coping and roof drain applications.

3.07 WALKWAYS

A. Install walkways at all traffic concentration points (such as roof hatches, access doors, rooftop ladders, etc.)

and all locations as identified on the specifier's drawing.

B. Hot air weld walkway material to the membrane in accordance with the manufacturer's specifications.

3.08 DAILY SEAL

A. On phased roofing, when the completion of flashings and terminations is not achieved by the end of the work day, a daily seal must be performed to temporarily close the membrane to prevent water infiltration.

B. Complete an acceptable membrane seal in accordance with the manufacturer's requirements.

3.09 CLEAN UP

A. Perform daily clean-up to collect all wrappings, empty containers, paper, and other debris from the project site. Upon completion, all debris must be disposed of in a legally acceptable manner.

B. Prior to the manufacturer's inspection for warranty, the applicator must perform a pre-inspection to review all work and to verify all flashing has been completed as well as the application of all caulking.

END OF SPECIFICATION

BUILDING SOLUTIONS

WELD

TPO Roofing Systems

T P O R O O F I N G S Y S T E M S

WELD

Excellent Heat and UV Resistance

Long-term Energy Efficiency in Warm, Southern Climates

Cleaner Surface Improved Long-term Performance

Industry Leading Weathering Package

Greater Weather Resistance

Why Choose TPO?

Thermoplastic polyolefin (TPO) membranes are the fastest-growing segment in the commercial roofing industry and are highly reflective and heat/UV resistant. TPO membranes first became commercialized for roofing membranes in the late 1980’s and since 2007 has been the largest market segment of low-slope roofing.

Versico Roofing Systems’ VersiWeld TPO membrane is comprised of three layers – a TPO polymer base; a strong, polyester-reinforced fabric center (scrim) and a tough thermoplastic polyolefin compounded top-ply.

Because the top-ply is the most vital membrane component for long-term weathering characteristics, Versico manufactures all of its TPO membranes with an industry leading thicker top-ply over scrim. VersiWeld TPO is also packed with the industry leading OctaGuard XT™ weathering package, a combination of ingredients that allow VersiWeld TPO to stand up to the toughest weather conditions and stand the test of time.

WHY CHOOS E VERS IWELD ® TPO?

Advantages of VersiWeld TPO

Versico has been at the forefront of TPO development for nearly 20 years and continues to lead the industry with its high-performance OctaGuard XT weathering package that is incorporated into VersiWeld TPO membrane and accessories. OctaGuard XT weathering package technology is comprised of eight performance-enhancing ingredients, including three heat-stabilizing antioxidants and three UV light stabilizers as well as organic and inorganic UV absorbers. When combined, these eight ingredients provide a weathering package second to none in the TPO industry.

The Tests TPO membrane samples from four manufacturers, including Versico, were recently subjected to accelerated heat aging in a controlled 240ºF environment. Heat aging accelerates the impact that heat plays on TPO and evaluates its performance on the roof. Samples were removed when they showed signs of cracking or were deemed not suitable to perform as a waterproofing membrane. Extreme Xenon Arc Weatherometer testing also reveals that VersiWeld TPO can withstand twice the ASTM D6878 requirement of 10,080 kJ/m2 without losing its desired physical properties.

The Results Independent test results and a chemical analysis show that VersiWeld TPO with OctaGuard XT contains more weather-protecting ingredients than any other TPO membrane tested, which means Versico’s TPO provides superior long-term protection against the dangers of heat and UV exposure.

With Versico’s VersiWeld TPO, featuring OctaGuard XT weathering package, you get a whiter, cleaner and more energy-efficient, longer-lasting and weather-resistant TPO roofing system. Versico’s VersiWeld TPO with OctaGuard XT weathering package technology has set a new standard in the thermoplastic single-ply industry.

Whiter, Longer As a white membrane collects dirt, the cost savings associated with having a reflective roof are severely reduced and the higher associated temperatures can accelerate aging. The time-tested VersiWeld TPO compound, which includes OctaGuard XT along with Versico’s state-of-the-art manufacturing process, produces one of the smoothest TPO sheets on the market. The extremely smooth top ply of Versico’s TPO reduces the ability of dirt, mold, bacteria and other contaminants to collect on the membrane, keeping it whiter longer and increasing the efficiency and potential lifespan of your TPO roof.

Versico VersiWeld – 60 Weeks (No Failure)

Heat Aging Following ASTM D6878 Protocol

“Competitor C” TPO – 37 Weeks

Reflectivity Warranty Versico backs their commitment to long-term performance and energy-efficiency with an industry-leading Reflectivity Warranty on all white TPO membranes. A warranty backed by a company with over 50 years of single-ply manufacturing experience.

Benefits of a Versico VersiWeld TPO roof system featuring the OctaGuard XT weathering package include:

• Cleaner surface

• Long-term energy efficiency in warm, southern climates

• Greater weather resistance

• Improved long-term performance

• Heat and UV resistance

S Y S T E M O P T I O N S

Mechanically Attached Systems Mechanically Attached Systems require mechanical attachment of the insulation to the deck and mechanical attachment of the membrane within the seam area. Adjoining membrane sheets are overlapped and joined together by hot-air welding.

Induction Welded Systems Induction welded systems use fasteners and specially coated plates to secure both the insulation and membrane. Each coated plate is heated with a special induction tool and then cooled using a magnet to secure the membrane to each plate.

Adjoining membrane sheets are overlapped and joined together by hot air welding.

Fully Adhered Systems Fully Adhered Systems require mechanical or adhesive attachment of the insulation to the roof deck. The TPO membrane and substrate are then coated with bonding adhesive and the membrane is rolled into place and seams are then hot-air welded.

Quick-Applied Systems VersiWeld QA (Quick-Applied) TPO membrane is a 60-or 80-mil TPO membrane laminated to an elastomeric quick-applied adhesive. The pre-applied adhesive eliminates VOC and odor concerns typically associated with fully adhered systems.

VersiFleece TPO VersiFleece TPO membranes are manufactured using a hot-melt extrusion process for complete scrim encapsulation, are chlorine- and plasticizer-free, and provide excellent long-term reflectivity. Versico’s VersiFleece TPO contains the OctaGuard XT weathering package, which provides excellent resistance to UV and extreme temperatures.

Colors White, Gray, Tan. *Special Colors: Medium Bronze, Rock Brown, Terra Cotta, Slate Gray, Patina Green

Thicknesses TPO + Fleece: 100, 115, and 135 mils

Standard Widths 6' and 12'

Standard Lengths 50' and 100' (100- and 115-mil) 75' (135-mil)

*Special Colors available in limited thicknesses and sizes.

Contact a Versico Representative for more details.

Membrane Options VersiFleece TPO Membrane

Flexible DASH Adhesive

Versico Fasteners and Plates

2" VersiCore MP-H Polyiso Insulation

Steel Deck

Versico’s RapidLock Roofing Systems

Versico’s RapidLock (RL) Roofing System is a revolutionary membrane attachment method that provides a fully adhered system without the use of adhesives. The RL system utilizes VELCRO® Brand Securable Solutions along with VersiFleece RL TPO to achieve performance on par with traditional fully adhered single-ply systems.

Underlayment options include VersiCore MP-H RL , SecurShield RL Polyiso, or SecurShield HD RL Polyiso. The RL system is VOC- and odor-free, has no application temperature restrictions, and provides significant labor savings thanks to the simplicity of the system and ease of installation.

System Features & Benefits

• No application temperature restrictions

• VOC- and odor-free

• Adhesive-less system saves time and labor

• RL fleece is specifically designed to work with RL Insulation facer and features a removable slip sheet for ease of installation

• Excellent Wind uplift performance and ratings (up to FM 1-225), comparable to traditional fully adhered single-ply systems

• Fleece reinforcement adds toughness, durability, and enhanced resistance to hail and punctures

VersiFleece® RL™ TPO Membrane with RapidLock Technology

Insulation Fasteners and Plates

VersiCore MP-H® RL Polyiso, SecurShield® RL Polyiso or SecurShield HD RL Polyiso with RapidLock Technology

VersiCore MP-H Polyiso or SecurShield Polyiso

Steel Deck

Versico’s patented APEEL Protective Film guards the surface of TPO membrane from scuffs and dirt accumulation during installation, eliminating the need to clean the roof once the project is complete.

Durable and easy to remove, APEEL Protective Film helps save time and labor, improves aesthetics and increases customer satisfaction. VersiWeld TPO membrane with APEEL Protective Film is ideal for re-roofing, re-cover and new construction projects.

Features and Benefits:

• Tough protective film helps prevent scuffs and scratches on TPO membrane during the construction process

• Holes in the film can easily check for accidental cuts or punctures made during installation

• Eliminates the need to clean the roof after installation

• Perfect adhesion level keeps the film in place until you remove it

• Film is easily removed by one person due to its manageable 5-foot-wide size

• Gray color helps the surface dry quickly and cuts down on glare

Versico’s APEEL 6" Cover Tape & APEEL Cover Tape Applicator Versico’s APEEL 6" Cover Tape and APEEL Cover Tape Applicator allow contractors to keep 100 percent of the TPO surface – including the seams and areas around details – clean during installation.

V E R S I W E L D T P O W I T H A P E E L™ P R O T E C T I V E F I L M

VersiWeld Plus TPO is Versico’s thickest, most durable, and longest-lasting TPO membrane. Available in standard and fleece-backed versions, VersiWeld Plus TPO provides excellent long-term durability and exceptional resistance to hail and punctures. VersiWeld Plus TPO also offers superb UV resistance due to the increased levels of Versico’s OctaGuard XT Weathering Package that thicker membranes contain.

Versico’s VersiWeld Plus TPO products include:

• 80-mil VersiWeld TPO

• 135-mil VersiFleece TPO

• 155-mil VersiFleece AC TPO

Dependability Because of their unmatched performance, VersiWeld Plus membranes are available with a variety of enhanced warranty packages. The warranty packages available for VersiWeld Plus membranes include:

• Puncture warranty

• 10-year reflectivity warranty (available for white membranes)

• 30-year No Dollar Limit watertight warranty, which covers:

- Membrane, insulation, fasteners, and terminations

- Accidental puncture

- Wind damage up to 120 mph

- Hail damage (up to 2")

Each detail of a VersiWeld Plus TPO roofing system is meticulously engineered by Versico to ensure its long-term performance. Every square inch of VersiWeld Plus TPO is enhanced with the most advanced weathering package on the market: Versico’s OctaGuard XT.

P l u s T P O R o o f i n g S y s t e m s

WELD

Because thicker TPO membranes contain higher levels of the OctaGuard XT weathering package, Verisco’s 80-mil VersiWeld Plus TPO provides longer-lasting protection against the negative effects of UV degradation and heat exposure. The additional protection provided by an upgrade to VersiWeld Plus TPO often adds as little as 8% to the system’s total installed costs, while increasing the lifespan of the roof by as much as 33%.

All of these dependable attributes lead to unmatched warranties for VersiWeld Plus TPO roof systems.

V E R S I W E L D P L U S T P O

White

Gray

Tan

VersiWeld TPO Colors In Stock

Medium Bronze Terra CottaSlate Gray Patina GreenRock Brown

Turn your roof into a canvas with Versico’s TPO Special Color Program. The leader in single-ply technology offers more pre-formulated colors than any other manufacturer in the marketplace with reinforced membrane available in 10' x 100' sheets, non-reinforced flashing available in 24" x 50' rolls, TPO Rib Profiles, custom accessories and flashings, and TPO coated metal available in 4' x 10' sheets.

Special Color Program tpo

* Color samples printed here are approximations. For actual colors, request a sample of TPO Special Color Membrane.

** Special Color membranes will ‘fade’ over time mainly due to the ultraviolet portion of sunlight. Since most roof surfaces are exposed to variable sunlight, some areas will be more susceptible to color changes caused by UV fading.

Warranties for Special Color membranes do not cover fading of colors.

V E R S I W E L D H S T P O S P E C I A L C O L O R P R O G R A M

Metal buildings are often chosen because of their cost-effective design and speed of construction. However, when the metal roof begins to leak and deteriorate replacement can be very costly. With decades of experience in single-ply roofing, Versico Roofing Systems has a wide range of metal retrofit options.

Versico’s VersiWeld TPO can be installed over an existing standing seam metal roof to offer proven, long-lasting protection while increasing the energy efficiency of the building. This solution can be more cost effective than replacing the metal roof while proving to be a much longer-term solution compared to coatings.

Convenience, value, and performance are three critical considerations when it comes to the success of any re-roofing project. A VersiWeld TPO Metal Retrofit System offers the following features and benefits:

Multiple membrane and insulation options to meet a variety of performance, budget, and efficiency needs.

Installs directly over the existing metal roof eliminating costly and disruptive removal and replacement.

Improves R-value and energy efficiency of the building while reducing noise for occupants.

Highly reflective TPO membranes offer additional energy savings.

Backed by Versico’s industry-leading Total System Warranty for up to 20 years, with optional hail, puncture and reflectivity warranties available upon request.

TPO’s proven history of long-term performance provides a lasting solution compared to coatings and spray-applied restoration products.

Convenience Value Performance

W H Y C H O O S E A V E R S I W E L D T P O

M E TA L R E T R O F I T S Y S T E M ?

EPS Flute Fill

Polyiso Flute Fill

Existing Standing Seam Metal Roof

Flute Fill Insulation: a key component of a metal retrofit system is the addition of custom-fit insulation between the standing seams of the metal roof panels. Versico offers both EPS (expanded polystyrene – shown) and Polyiso flute-fill insulation that can be factory cut to fit between each metal panel. This insulation layer also adds R-value and can be loose-laid or adhered.

Additional insulation: once flute-fill has been installed, additional insulation ranging from a ¼-inch cover board to several inches of Polyiso insulation can be installed to create a smooth flat substrate for the membrane. Adding thicker Polyiso insulation and cover boards can add additional R-value to the system. Using a high-compressive strength Polyiso cover board or gypsum cover board can also enhance impact resistance and fire resistance.

3 Attachment: the VersiWeld TPO membrane can be mechanically attached using fasteners and plates, attached using induction welding plates, or fully adhered using a TPO bonding adhesive.

See the back cover for more information on each attachment method.

VersiWeld TPO Membrane: the adjoining TPO membrane sheets are hot-air welded together using an approved hot-air welder.

IN STALL ING TPO METAL RETROFIT SYSTEMS

A C C E S S O R I E S & A D H E S I V E S

Non-Reinforced Flashing Yellow Pressure-Sensitive Warning Strip

Pressure-Sensitive Coverstrip

Pressure-Sensitive RUSS Molded Pipe SealsSplit Pipe-Seals

1-TPO Inside Corners 2-TPO Outside Corners

3-TPO T-Joint Covers

Curb Wrap Corners Molded Sealant Pockets

Universal Corners TPO Bonding Adhesive

TPO Rib Profile

CAV-GRIP® 3V Low- VOC Adhesive/Primer

Low-VOC Primer

8 0 0.992.7663 • w w w.ver s ico.com

A S I N G L E S O U R C E F O R S I N G L E - P LY R O O F I N G

© 2020 Versico. Printed in U.S.A.

REPRINT REQUEST CODE: 601733 VE-1215 - “VersiWeld Brochure” - 11.17.20

Versico, VersiWeld, OctaGuard XT, VersiCore MP-H, VersiFleece, APEEL, and the Versico logo are trademarks of Versico.

SecurShield, RL, and CAV-GRIP are trademarks of Carlisle Construction Materials, LLC. VELCRO is a registered trademark of Velcro BVBA.

ENERGY STAR is a registered trademark owned by the U.S. Government. *ENERGY STAR qualification is only valid in the U.S.

10 TH INGS TO CON S IDER WHEN INVESTING

IN A TPO ROOFING SYSTEM

Experience and Innovation: Versico has led the industry in TPO research and development for over 20 years. Billions of square feet of TPO membrane have been installed on rooftops across the globe.

That’s more than any other manufacturer.

Weathering Package: Versico’s TPO membrane is enhanced with OctaGuard XT Weathering Package which results in the most dependable, long-term performance characteristics in the industry.

Seam Strength: Independent tests show that Versico’s TPO membrane exhibits far stronger seams than competing products. That means better wind uplift performance and fewer leaks.

Weldability: VersiWeld TPO membranes can be welded at the widest temperature and humidity ranges resulting in strong welds without having to modify welder settings to compensate for changing climatic conditions.

Energy Efficiency: Versico’s White TPO membrane features an initial ENERGY STAR®* solar reflectance of .79 and emissivity of .90.

Appearance: a combination of our state-of-the-art manufacturing process and over 20 years of manufacturing experience creates a smoother top surface designed to resist dirt, debris, mildew and bacteria build-up. That means you get a cleaner, more solar reflective membrane throughout the life of your roof.

Diversity and Versatility: Versico manufactures VersiWeld TPO membranes with a wide range of thicknesses, widths, lengths and colors, providing the ability to get the perfect TPO membrane for your roofing project.

Thickness over Scrim: Versico’s TPO features a typical thickness over scrim well above the ASTM minimum. This thickness leads to greater weathering resistance for added protection against solar heat and UV.

Warranties: Versico’s Total System warranties, as well as a large warranty reserve, reflect a commitment and ability to address any warranty issue.

Prefabricated Accessories: Versico offers over a dozen prefabricated, in-stock, accessories and countless custom-order accessories. All carry a CFA (Certified Fabricated Accessory) stamp of approval, so you know they are manufactured to the highest standards.

WELD

Mechanically Attached Roofing System

BUILDING PERFORMANCE

Typical Application

VersiWeld® Reinforced TPO Membrane

Versico Insulation Fasteners and Plates

Acceptable Insulation

Approved Roof Deck

Membrane Fasteners and Plates

System Features and Benefits

• Heat-weldable membranes

• High wind uplift performance

• Resistance to hail and accidental punctures

• Top ply membrane thickness adds improved long-term weatherability and durability

• White and tan membranes are ENERGY STAR qualified

• OctaGuard XT™ weathering package provides superior long-term performance

Colors White, Gray and Tan

Standard Thicknesses 45-, 60- and 80-mil

Standard Widths 4', 6', 8', 10' and 12'

Standard Lengths 100'

Installation Versico’s VersiWeld TPO Mechanically Attached Roofing System utilizes white, gray, or tan membranes in standard reinforced 45- or 60-mil thickness or 80-mil thick reinforced VersiWeld Plus membranes.

Insulation is mechanically attached to an acceptable roof deck.

VersiWeld membrane sheets are mechanically attached to the deck with appropriate Versico fasteners and plates. Adjoining sheets are overlapped and joined together with a minimum 1½"-wide hot-air weld.

The above information represents a typical Versico VersiWeld TPO Mechanically Attached Roofing System. Refer to Versico’s published specifications and details for more complete information.

VersiWeld TPO Membrane Versico’s VersiWeld TPO is a premium, heat-weldable, single-ply thermoplastic polyolefin membrane, engineered to provide outstanding long-term performance in new roof construction and re-roofing applications. All VersiWeld TPO membranes utilize the patented OctaGuard XT weathering package technology, which is able to withstand extreme durability testing intended to simulate exposure to several climates.

© 2020 Versico. Printed in U.S.A.

VE-1230 - “VersiWeld MA System Sheet” – 11.04.20

VersiWeld, Octaguard XT and the Versico logo are trademarks of Versico.

ENERGY STAR is a registered trademark owned by the U.S. Government. *ENERGY STAR qualification is only valid in the U.S.

WELD

VersiWeld TPO Accessories Versico also offers over a dozen prefabricated, in-stock, standard-order accessories, and countless custom-order accessories. All carry a CFA (Certified Fabricated Accessory) stamp of approval, so you know they are manufactured to the highest standards.

Every Versico CFA-approved accessory saves time and money during installation.

System Codes

• UL Class A, B and Universal Slope ratings are available over any deck type

• FM Uplift values up to 135 psf can be achieved

For code specifics, refer to Versico’s Code Approval Guide.

Warranty Consult your Authorized Contractor, Versico Independent Sales Representative or Distributor for associated warranty charges.

Versico’s VersiWeld TPO systems are backed by our industry leading Total System Warranty. Five to thirty year total system warranties are available with optional hail, puncture and reflectivity warranties available upon request.

New Construction Re-roofing

Existing or New Deck Type Steel Plywood or OSB

Lt. Wt.

Concrete

Structural Concrete

Wood Planks

Gypsum & Fibrous Cement

Smooth- Surface

BUR

Gravel- Surfaced

BUR

Existing Single-Ply

Insulation Required Yes No Refer to Specs**

No Yes Yes No Yes Refer to Specs**

Recommended Insulations Approved Versico insulation or cover board

Insulation Attached By Versico fasteners and plates

Membrane Attached By

HPVX

Fasteners;

HPV-XL

Fasteners

HPVX

Fasteners;

HPV-XL

Fasteners

Gyptec Fasteners/

Plates

CD-10;

MP 14–10

Fasteners

HPVX

Fasteners

Gyptec Fasteners/

Plates

FOR TEAR-OFF OPTIONS REFER TO NEW CONSTRUCTION ABOVE.

For current code approvals and warranties, visit Versico’s website or contact a design analyst.

** Refer to Versico’s VersiWeld Design Criteria Portion of the Current Specification.

Optional APEEL Protective Film

• APEEL Protective Film guards the

TPO membrane’s surface from scuffs and dirt accumulation during installation, improving the roof system’s appearance and long-term performance.

• APEEL Protective Film can be left in place for up to 90 days without degrading due to its excellent heat-and UV-resistance.

VSW_20 Rev 04/19

DATE OF ISSUE:

WARRANTY NO.:

NAME OF BUILDING:

BUILDING ADDRESS:

Subject to the following terms and conditions, Versico, a division of Carlisle Construction Materials Incorporated (VERSICO) warrants to the Buyer that the membrane material (MEMBRANE) sold to the Buyer will be free from manufacturing defects at the time of its delivery to the job site.

If upon inspection by Versico, the membrane evidences manufacturing defects, Versico's liability and Buyer's remedies are limited, at Versico's option, to the repair or replacement of the defective membrane at the F.O.B. point in the original contract of sale.

Versico further warrants that the Membrane material will not prematurely deteriorate to the point of failure because of weathering for a period of years from the date of sale if properly installed, maintained and used for the purpose for which Versico intended.

Buyer shall give Versico notice of a claim under this warranty within thirty (30) days of discovering the premature deterioration of the Membrane.

If upon inspection by Versico, the Membrane shows premature deterioration because of weathering within the year period stated herein, Versico's liability and Buyer's remedies are limited at Versico's option to the providing of repair material for the original Membrane or credit to be applied towards the purchase of a new Membrane, the value of these remedies being determined by Versico based upon the number of remaining months of the unexpired warranty used to prorate at the current prices for the Membrane. The maximum prorated value allowed by Versico for repair or credit shall not exceed the original Membrane purchase price.

This warranty refers to the membrane material only. Flashings, adhesives and other accessories contained in a membrane system are not covered by this warranty.

Versico shall not be responsible for the cleanliness or discoloration of the membrane material caused by environmental conditions including, but not limited to, dirt, pollutants or biological agents.

NO REPRESENTATIVE OF VERSICO HAS AUTHORITY TO MAKE ANY REPRESENTATIONS OR PROMISES

EXCEPT AS STATED HEREIN.

THERE ARE NO WARRANTIES EITHER EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WHICH EXTEND BEYOND THE

WARRANTIES CONTAINED IN THIS DOCUMENT. VERSICO SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES, INCLUDING BUT NOT LIMITED TO, LOSS OF PROFITS OR DAMAGES

TO THE STRUCTURE OR ITS CONTENTS ARISING UNDER ANY THEORY OF LAW WHATSOEVER.

BY: Lorraine Russ

AUTHORIZED SIGNATURE

TITLE: General Manager

A

PSM

LE iability and Buyer'sability and Buyer he F.O.B. point in the orige F.O.B. point in the eriorate to the point of failure becausnt of failure becau d, maintained and…