SOO_5_Feb_15.pdf

SPE601-15-R-0308 ABO and LN2Multiple Locations CONUS Northeastern Region

STATEMENT OF OBJECTIVES

2 Oct 14

Barnes ANG, MA

1. DESCRIPTION OF REQUIREMENT: Defense Logistics Agency Energy (DLA Energy), as the Department of Defense (DoD) Integrated Materiel Manager (IMM) for Aerospace Energy products and related services, requires delivery of Aviator’s Breathing Oxygen (ABO). The Contractor shall provide all materials, supplies, product, management, tools, equipment, transportation and labor necessary to deliver product f.o.b. destination into Government-owned tanks at Barnes ANG, MA.

2. PRODUCT SPECIFICATIONS:

2.1. ABO (NSN 6830-00-808-9531) shall meet the requirements of Type II of specification MIL-PRF-27210J, dated 7 Aug 2013.

2.1.1. MIL-PRF-27210J, paragraph 4.2.1: Preproduction samples are not required if the Contractor’s fill point is already supplying one or more DoD locations with ABO in accordance with all the requirements of MIL-PRF-27210J, including the requirement for submitting periodic samples to a Government approved laboratory listed below in paragraph 2.1.5 “ABO Sample Submission Table”.

2.1.2. MIL-PRF-27210J, paragraph 4.2.2: Preproduction samples (if required) and all periodic sample submissions shall be submitted at the Contractor’s expense to a laboratory listed below in paragraph 2.1.5, “ABO Sample Submission Table”.

Contractor’s submitting samples shall attach/include a properly prepared DD Form 1222, Request for and Results of Test, with each sample clearly marking them as either a Preproduction and/or a Periodic Sample. The submitting Contractor shall also arrange return shipment of the sample containers from the assigned Government laboratory.

2.1.3. MIL-PRF-27210J, paragraph 4.3.1.2: A representative sample of Type II may also be obtained by withdrawing a sample from the sampling port on the shipping container directly into the analytical instrument(s).

2.1.4. The entire contents of a Type II ABO shipping conveyance offered for acceptance by the Government should be produced from a facility that meets all of the requirements of this Statement of Objectives. If the shipping conveyance contains any liquid product that was not produced from an approved facility (such as a product heel from a different fill point), a representative sample shall be drawn from the conveyance (after filling) and tested to determine compliance with the requirements of this Statement of Objectives and Table 1 of MIL-PRF-27210J. .

SPE601-15-R-0308 ABO and LN2Multiple Locations

2.1.5. ABO Sample Submission Table.

2.2 In addition to the reports required elsewhere within this contract, one copy of a Certificate of Analysis for each sample required by the specification shall be submitted as an attachment to the applicable Wide Area Workflow (WAWF) Combo document or documented on the WAWF Statement of Quality tab.

3. PRODUCT ORDERING: The DLA Energy Contracting Officer shall issue Individual Delivery Orders (DD Form 1155) for obligation of funds for orders to be issued during that specific timeframe by the appointed Ordering Officer. The individual orders placed by the appointed Ordering Officer will designate the specific quantity to be delivered at the customer location specified in the contract.

4. PRODUCT DELIVERY:

4.1 Product shall be delivered within 7 days after receipt of an order from the appointed Delivery Scheduler. No emergency deliveries are anticipated.

4.2 Deliveries shall be made from 0630-1600 hours, Monday-Friday, excluding federal holidays.

ABO SAMPLE SUBMISSION TABLE

SUPPLIER FILLPOINTS LOCATED IN THE BELOW

STATES:

ARE ASSIGNED THE BELOW LABS

FOR SUBMITTING PRE-

PRODUCTION AND PERIODIC

SAMPLES:

AR, CT, DE, IL, IN, IA, KS, KY, ME, MD, MA, MI, MN, MO,

NE, NH, NJ, NY, NC, ND, OH, OK, PA, RI, TN, TX, VT, VA,

WV, WI

Aerospace Fuels Laboratory (FP2070)

AFPA/PTPLA

2430 C Street Bldg 70 Area B Wright-Patterson AFB OH 45433-7632

PH (937)255-2946

AK, AZ, CA, CO, ID, MT, ND, NV, NM, OR, UT, WA, WY Aerospace Fuels Laboratory (FP2075)

AFPA/PTPLE

1747 Utah Ave Bldg 6670 Vandenberg AFB CA 93437-5220

PH (805)606-5873

AL, FL, GA, LA, MS, SC Aerospace Fuels Laboratory (FP2078)

AFPA /PTPLH

15251 Scrub Jay Street Bldg 54800 Cape Canaveral AFS FL 32920

PH (321)85

Or Navair Depot Jacksonville Materials Engineering Lab Code 4.9.7.5 Building 793 Jacksonville FL 32212-0016 3-5441

SPE601-15-R-0308 ABO and LN2Multiple Locations

4.3 Product deliveries shall be made to the following address:

Barnes ANGB Bldg 38 175 Falcon Dr.

Westfield, MA 01085

5. DESCRIPTION OF GOVERNMENT-OWNED ABO TANKS: ABO shall be delivered into the following Government-owned storage vessels listed below. The storage vessels will be trailer accessible.

Location Tank Capacity-Gallons MAWP Bldg. 38 2 - 3,000 GL ea 70 psig ea

6. TANK OVER-PRESSURE PROTECTION: If it is determined during supplier site visits or upon review of tank technical information that additional tank over-pressure protection is required to comply with CGA P-59, Prevention of Over-Pressure During Filling of Cryogenic Vessels, the Contractor shall provide and install the additional tank protection which may encompass any of the methods identified in the P-59. NOTE:

Over-protection devices shall not be installed on Government-owned storage tanks without prior coordination with DLA Energy-FEM and the activity that physically possesses the tank(s).

7. INSPECTION AND ACCEPTANCE: Inspection for quality shall be performed at origin. Quantity determination and acceptance shall be at destination.

8. METHOD OF MEASUREMENT: Quantity determination to be performed at delivery location by use of a truck mounted calibrated flow meter.

9. HOT FILLS: Occasionally, the Contractor may be required to perform a “Hot Fill” in order to cool-down and refill any tank that has gone empty and is warm.

10. SECURITY REQUIREMENTS: Drivers will need to check in at guard post and be escorted in to the Liquid Oxygen facility by Fuels personnel .

SPE601-15-R-0308 ABO and LN2Multiple Locations

Westover ARB, MA

1. DESCRIPTION OF REQUIREMENT: Defense Logistics Agency Energy (DLA Energy), as the Department of Defense (DoD) Integrated Materiel Manager (IMM) for Aerospace Energy products and related services, requires delivery of Aviator’s Breathing Oxygen (ABO) and Liquid Nitrogen (LN2). The Contractor shall provide all materials, supplies, product, management, tools, equipment, transportation and labor necessary to deliver product f.o.b. destination into Government-owned tanks at Westover ARB, MA.

2. PRODUCT SPECIFICATIONS:

2.1 ABO (NSN 6830-00-808-9531) shall meet the requirements of Type II of specification MIL-PRF-27210J, dated 7 Aug 2013.

2.1.1 MIL-PRF-27210J, paragraph 4.2.1: Preproduction samples are not required if the Contractor’s fill point is already supplying one or more DoD locations with ABO in accordance with all the requirements of MIL-PRF-27210J, including the requirement for submitting periodic samples to a Government approved laboratory listed below in paragraph 2.1.5 “ABO Sample Submission Table”.

2.1.2 MIL-PRF-27210J, paragraph 4.2.2: Preproduction samples (if required) and all periodic sample submissions shall be submitted at the Contractor’s expense to a laboratory listed below in paragraph 2.1.5, “ABO Sample Submission Table”.

Contractor’s submitting samples shall attach/include a properly prepared DD Form 1222, Request for and Results of Test, with each sample clearly marking them as either a Preproduction and/or a Periodic Sample. The submitting Contractor shall also arrange return shipment of the sample containers from the assigned Government laboratory.

2.1.3 MIL-PRF-27210J, paragraph 4.3.1.2: A representative sample of Type II may also be obtained by withdrawing a sample from the sampling port on the shipping container directly into the analytical instrument(s).

2.1.4 The entire contents of a Type II ABO shipping conveyance offered for acceptance by the Government should be produced from a facility that meets all of the requirements of this Statement of Objectives. If the shipping conveyance contains any liquid product that was not produced from an approved facility (such as a product heel from a different fill point), a representative sample shall be drawn from the conveyance (after filling) and and Table 1 of MIL-PRF-27210J.

SPE601-15-R-0308 ABO and LN2Multiple Locations

2.1.5 ABO Sample Submission Table.

2.2 LN2 (NSN 6830-00-285-4769) shall meet the requirements of Type II, Grade B, Commercial Item Description A-A 59503C dated 3 Mar 2011, Nitrogen, Technical.

2.3 In addition to the reports required elsewhere within this contract, one copy of a Certificate of Analysis for each sample required by the specification shall be submitted that specific timeframe by the appointed Ordering Officer. The individual orders placed by the appointed Ordering Officer will designate the specific quantity to be delivered at the customer location specified in the contract.

4. PRODUCT DELIVERY:

4.1 Product shall be delivered within 7 days after receipt of an order from the appointed Delivery Scheduler. No emergency deliveries are anticipated.

4.2 Deliveries shall be made from 0700-1500 hours, Monday-Friday, excluding federal

PRODUCTION AND PERIODIC

SAMPLES:

AR, CT, DE, IL, IN, IA, KS, KY, ME, MD, MA, MI, MN, MO,

NE, NH, NJ, NY, NC, ND, OH, OK, PA, RI, TN, TX, VT, VA,

WV, WI

Aerospace Fuels Laboratory (FP2070)

AFPA/PTPLA

2430 C Street Bldg 70 Area B Wright-Patterson AFB OH 45433-7632

PH (937)255-2946

AK, AZ, CA, CO, ID, MT, ND, NV, NM, OR, UT, WA, WY Aerospace Fuels Laboratory (FP2075)

AFPA/PTPLE

1747 Utah Ave Bldg 6670 Vandenberg AFB CA 93437-5220

PH (805)606-5873

AL, FL, GA, LA, MS, SC Aerospace Fuels Laboratory (FP2078)

AFPA /PTPLH

15251 Scrub Jay Street Bldg 54800 Cape Canaveral AFS FL 32920

PH (321)85

Or Navair Depot Jacksonville Materials Engineering Lab Code 4.9.7.5

SPE601-15-R-0308 ABO and LN2Multiple Locations

Fuels Management 100 Logistics Dr., Bldg 7064 Chicopee (Westover) ARB, MA 01022-1530

5. DESCRIPTION OF GOVERNMENT-OWNED ABO & LN2 TANKS: ABO and LN2 shall be delivered into the following Government-owned storage vessels listed below.

The storage vessels will be trailer accessible.

Location Tank Capacity-Gallons MAWP Bldg 7064 2 - 3,000 GL ea ABO 50 psig ea 2 - 6,000 GL ea LN2 50 psig ea protection is required to comply with CGA P-59, Prevention of Over-Pressure During Filling of Cryogenic Vessels, the Contractor shall provide and install the additional tank protection which may encompass any of the methods identified in the P-59. NOTE:

Over-protection devices shall not be installed on Government-owned storage tanks without prior coordination with DLA Energy-FEM and the activity that physically possesses the tank(s).

7. INSPECTION AND ACCEPTANCE: Inspection for quality shall be performed at origin. Quantity determination and acceptance shall be at destination.

8. METHOD OF MEASUREMENT: Quantity determination to be performed at delivery location by use of a truck mounted calibrated flow meter.

9. HOT FILLS: Occasionally, the Contractor may be required to perform a “Hot Fill” in order to cool-down and refill any tank that has gone empty and is warm.

10. SECURITY REQUIREMENTS: The Contractor’s driver will be escorted from the main gate to the delivery location.

SPE601-15-R-0308 ABO and LN2Multiple Locations

Quonset ANG, RI

Aerospace Energy products and related services, requires delivery of Aviator’s Breathing Oxygen (ABO). The Contractor shall provide all materials, supplies, product, management, tools, equipment, transportation and labor necessary to deliver product f.o.b. destination into Government-owned tanks at Quonset ANG, RI.

2. PRODUCT SPECIFICATIONS:

2.1 ABO (NSN 6830-00-808-9531) shall meet the requirements of Type II of specification MIL-PRF-27210J, dated 7 Aug 2013.

2.1.1 MIL-PRF-27210J, paragraph 4.2.1: Preproduction samples are not required if the Contractor’s fill point is already supplying one or more DoD locations with ABO in accordance with all the requirements of MIL-PRF-27210J, including the requirement for submitting periodic samples to a Government approved laboratory listed below in paragraph 2.1.5 “ABO Sample Submission Table”.

2.1.2 MIL-PRF-27210J, paragraph 4.2.2: Preproduction samples (if required) and all periodic sample submissions shall be submitted at the Contractor’s expense to a laboratory listed below in paragraph 2.1.5, “ABO Sample Submission Table”.

Contractor’s submitting samples shall attach/include a properly prepared DD Form 1222, Request for and Results of Test, with each sample clearly marking them as either a Preproduction and/or a Periodic Sample. The submitting Contractor shall also arrange return shipment of the sample containers from the assigned Government laboratory.

2.1.3 MIL-PRF-27210J, paragraph 4.3.1.2: A representative sample of Type II may also be obtained by withdrawing a sample from the sampling port on the shipping container directly into the analytical instrument(s).

2.1.4 The entire contents of a Type II ABO shipping conveyance offered for acceptance by the Government should be produced from a facility that meets all of the requirements of this Statement of Objectives. If the shipping conveyance contains any liquid product that was not produced from an approved facility (such as a product heel from a different fill point), a representative sample shall be drawn from the conveyance (after filling) and

SPE601-15-R-0308 ABO and LN2Multiple Locations that specific timeframe by the appointed Ordering Officer. The individual orders placed by the appointed Ordering Officer will designate the specific quantity to be delivered at the customer location specified in the contract.

4. PRODUCT DELIVERY:

4.1 Product shall be delivered within 7 days after receipt of an order from the appointed Delivery Scheduler. No emergency deliveries are anticipated.

4.2 Deliveries shall be made from 0800-1600 hours, Tuesday-Friday, excluding federal holidays.

4.3 Product deliveries shall be made to the following address:

143d RI ANG Fuels Management Flight

ABO SAMPLE SUBMISSION TABLE

PRODUCTION AND PERIODIC

SAMPLES:

AR, CT, DE, IL, IN, IA, KS, KY, ME, MD, MA, MI, MN, MO,

NE, NH, NJ, NY, NC, ND, OH, OK, PA, RI, TN, TX, VT, VA,

WV, WI

Aerospace Fuels Laboratory (FP2070)

AFPA/PTPLA

2430 C Street Bldg 70 Area B Wright-Patterson AFB OH 45433-7632

PH (937)255-2946

AK, AZ, CA, CO, ID, MT, ND, NV, NM, OR, UT, WA, WY Aerospace Fuels Laboratory (FP2075)

AFPA/PTPLE

1747 Utah Ave Bldg 6670 Vandenberg AFB CA 93437-5220

PH (805)606-5873

AL, FL, GA, LA, MS, SC Aerospace Fuels Laboratory (FP2078)

AFPA /PTPLH

15251 Scrub Jay Street Bldg 54800 Cape Canaveral AFS FL 32920

PH (321)85

Or Navair Depot Jacksonville Materials Engineering Lab Code 4.9.7.5

SPE601-15-R-0308 ABO and LN2Multiple Locations

Building 514/515 14 Hercules Drive Quonset Pt North Kingstown RI 02852

5. DESCRIPTION OF GOVERNMENT-OWNED ABO TANKS: ABO shall be delivered into the following Government-owned storage vessels listed below. The storage vessels will be trailer accessible.

Location Tank Capacity-Gallons MAWP Bldg 514/515 1 - 3,000 GL 50 psig 1 – 400 GL 50 psig

6. TANK OVER-PRESSURE PROTECTION: If it is determined during supplier site visits or upon review of tank technical information that additional tank over-pressure protection is required to comply with CGA P-59, Prevention of Over-Pressure During Filling of Cryogenic Vessels, the Contractor shall provide and install the additional tank protection which may encompass any of the methods identified in the P-59. NOTE:

Over-protection devices shall not be installed on Government-owned storage tanks without prior coordination with DLA Energy-FEM and the activity that physically possesses the tank(s).

7. INSPECTION AND ACCEPTANCE: Inspection for quality shall be performed at origin. Quantity determination and acceptance shall be at destination.

8. METHOD OF MEASUREMENT: Quantity determination to be performed at delivery location by use of a truck mounted calibrated flow meter.

9. HOT FILLS: Occasionally, the Contractor may be required to perform a “Hot Fill” in order to cool-down and refill any tank that has gone empty and is warm.

10. SECURITY REQUIREMENTS: The Contractor’s driver will need identification and delivery paperwork and will be escorted from the main gate to the delivery location.

Burlington ANG, VT

Aerospace Energy products and related services, requires delivery of Aviator’s Breathing Oxygen (ABO). The Contractor shall provide all materials, supplies, product, management, tools, equipment, transportation and labor necessary to deliver product f.o.b. destination into Government-owned tanks at Burlington ANG, VT.

SPE601-15-R-0308 ABO and LN2Multiple Locations

2. PRODUCT SPECIFICATIONS:

2.1 ABO (NSN 6830-00-808-9531) shall meet the requirements of Type II of specification MIL-PRF-27210J, dated 7 Aug 2013.

2.1.1 MIL-PRF-27210J, paragraph 4.2.1: Preproduction samples are not required if the Contractor’s fill point is already supplying one or more DoD locations with ABO in accordance with all the requirements of MIL-PRF-27210J, including the requirement for submitting periodic samples to a Government approved laboratory listed below in paragraph 2.1.5 “ABO Sample Submission Table”.

2.1.2 MIL-PRF-27210J, paragraph 4.2.2: Preproduction samples (if required) and all periodic sample submissions shall be submitted at the Contractor’s expense to a laboratory listed below in paragraph 2.1.5, “ABO Sample Submission Table”.

Contractor’s submitting samples shall attach/include a properly prepared DD Form 1222, Request for and Results of Test, with each sample clearly marking them as either a Preproduction and/or a Periodic Sample. The submitting Contractor shall also arrange return shipment of the sample containers from the assigned Government laboratory.

2.1.3 MIL-PRF-27210J, paragraph 4.3.1.2: A representative sample of Type II may also be obtained by withdrawing a sample from the sampling port on the shipping container directly into the analytical instrument(s).

2.1.4 The entire contents of a Type II ABO shipping conveyance offered for acceptance by the Government should be produced from a facility that meets all of the requirements of this Statement of Objectives. If the shipping conveyance contains any liquid product that was not produced from an approved facility (such as a product heel from a different fill point), a representative sample shall be drawn from the conveyance (after filling) and

PRODUCTION AND PERIODIC

SAMPLES:

AR, CT, DE, IL, IN, IA, KS, KY, ME, MD, MA, MI, MN, MO,

NE, NH, NJ, NY, NC, ND, OH, OK, PA, RI, TN, TX, VT, VA,

WV, WI

Aerospace Fuels Laboratory (FP2070)

AFPA/PTPLA

2430 C Street Bldg 70 Area B Wright-Patterson AFB OH 45433-7632

PH (937)255-2946

AK, AZ, CA, CO, ID, MT, ND, NV, NM, OR, UT, WA, WY Aerospace Fuels Laboratory (FP2075)

AFPA/PTPLE

1747 Utah Ave Bldg 6670 Vandenberg AFB CA 93437-5220

PH (805)606-5873

SPE601-15-R-0308 ABO and LN2Multiple Locations that specific timeframe by the appointed Ordering Officer. The individual orders placed by the appointed Ordering Officer will designate the specific quantity to be delivered at the customer location specified in the contract.

4. PRODUCT DELIVERY:

4.1 Routine product deliveries shall be made within 7 days after receipt of an order from the appointed Delivery Scheduler. Emergency deliveries shall be made within 2 days after receipt of an order from the appointed Delivery Scheduler.

4.2 Deliveries shall be made from 0700-1500 hours, Tuesday-Friday, excluding federal holidays.

4.3 Product deliveries shall be made to the following address:

158th FW/LGRF, Vermont ANG 95 NCO Dr.

S. Burlington, VT 05403-5873

5. DESCRIPTION OF GOVERNMENT-OWNED ABO TANKS: ABO shall be delivered into the following Government-owned storage vessels listed below. The storage vessels will be trailer accessible.

Location Tank Capacity-Gallons MAWP 95 NCO Dr. 2 - 6,000 GL ea 55 psig ea Bldg 387

AL, FL, GA, LA, MS, SC Aerospace Fuels Laboratory (FP2078)

AFPA /PTPLH

15251 Scrub Jay Street Bldg 54800 Cape Canaveral AFS FL 32920

PH (321)85

Or Navair Depot Jacksonville Materials Engineering Lab Code 4.9.7.5

SPE601-15-R-0308 ABO and LN2Multiple Locations protection is required to comply with CGA P-59, Prevention of Over-Pressure During Filling of Cryogenic Vessels, the Contractor shall provide and install the additional tank protection which may encompass any of the methods identified in the P-59. NOTE:

Over-protection devices shall not be installed on Government-owned storage tanks without prior coordination with DLA Energy-FEM and the activity that physically possesses the tank(s).

7. INSPECTION AND ACCEPTANCE: Inspection for quality shall be performed at origin. Quantity determination and acceptance shall be at destination.

8. METHOD OF MEASUREMENT: Quantity determination to be performed at delivery location by use of a truck mounted calibrated flow meter.

9. HOT FILLS: Occasionally, the Contractor may be required to perform a “Hot Fill” in order to cool-down and refill any tank that has gone empty and is warm.

10. SECURITY REQUIREMENTS: Gate guards will check in Contractor’s driver and will call for escort to the delivery location.

Niagara Falls ARB, NY

Energy), as the Department of Defense (DoD) Integrated Materiel Manager (IMM) for Aerospace Energy products and related services, requires delivery of Aviator’s Breathing Oxygen (ABO). The Contractor shall provide all materials, supplies, product, management, tools, equipment, transportation and labor necessary to deliver product f.o.b. destination into Government-owned tanks at Niagara Falls ARB, NY.

2. PRODUCT SPECIFICATIONS:

2.1 ABO (NSN 6830-00-808-9531) shall meet the requirements of Type II of specification MIL-PRF-27210J, dated 7 Aug 2013.

2.1.1 MIL-PRF-27210J, paragraph 4.2.1: Preproduction samples are not required if the Contractor’s fill point is already supplying one or more DoD locations with ABO in accordance with all the requirements of MIL-PRF-27210J, including the requirement for submitting periodic samples to a Government approved laboratory listed below in paragraph 2.1.5 “ABO Sample Submission Table”.

SPE601-15-R-0308 ABO and LN2Multiple Locations

2.1.2 MIL-PRF-27210J, paragraph 4.2.2: Preproduction samples (if required) and all periodic sample submissions shall be submitted at the Contractor’s expense to a laboratory listed below in paragraph 2.1.5, “ABO Sample Submission Table”.

Contractor’s submitting samples shall attach/include a properly prepared DD Form 1222, Request for and Results of Test, with each sample clearly marking them as either a Preproduction and/or a Periodic Sample. The submitting Contractor shall also arrange return shipment of the sample containers from the assigned Government laboratory.

2.1.3 MIL-PRF-27210J, paragraph 4.3.1.2: A representative sample of Type II may also be obtained by withdrawing a sample from the sampling port on the shipping container directly into the analytical instrument(s).

2.1.4 The entire contents of a Type II ABO shipping conveyance offered for acceptance by the Government should be produced from a facility that meets all of the requirements of this Statement of Objectives. If the shipping conveyance contains any liquid product that was not produced from an approved facility (such as a product heel from a different fill point), a representative sample shall be drawn from the conveyance (after filling) and

ABO SAMPLE SUBMISSION TABLE

PRODUCTION AND PERIODIC

SAMPLES:

AR, CT, DE, IL, IN, IA, KS, KY, ME, MD, MA, MI, MN, MO,

NE, NH, NJ, NY, NC, ND, OH, OK, PA, RI, TN, TX, VT, VA,

WV, WI

Aerospace Fuels Laboratory (FP2070)

AFPA/PTPLA

2430 C Street Bldg 70 Area B Wright-Patterson AFB OH 45433-7632

PH (937)255-2946

AK, AZ, CA, CO, ID, MT, ND, NV, NM, OR, UT, WA, WY Aerospace Fuels Laboratory (FP2075)

AFPA/PTPLE

1747 Utah Ave Bldg 6670 Vandenberg AFB CA 93437-5220

PH (805)606-5873

AL, FL, GA, LA, MS, SC Aerospace Fuels Laboratory (FP2078)

AFPA /PTPLH

15251 Scrub Jay Street Bldg 54800 Cape Canaveral AFS FL 32920

PH (321)85

Or Navair Depot Jacksonville Materials Engineering Lab Code 4.9.7.5

SPE601-15-R-0308 ABO and LN2Multiple Locations that specific timeframe by the appointed Ordering Officer. The individual orders placed by the appointed Ordering Officer will designate the specific quantity to be delivered at the customer location specified in the contract.

4. PRODUCT DELIVERY:

4.1 Product deliveries shall be made within 7 days after receipt of an order from the appointed Delivery Scheduler. No emergency deliveries are anticipated.

4.2 Deliveries shall be made from 0800-1500 hours, Monday-Friday, excluding federal holidays.

4.3 Product deliveries shall be made to the following address:

Niagara Falls ARS 10980 Kinross Street Niagara Falls ARS, NY 14304

5. DESCRIPTION OF GOVERNMENT-OWNED ABO TANKS: ABO shall be delivered into the following Government-owned storage vessels listed below. The storage vessels will be trailer accessible.

Location Tank Capacity-Gallons MAWP Bldg 3110. 1 - 3,000 GL 55 psig 1 – 400 GL 55 psig

6. TANK OVER-PRESSURE PROTECTION: If it is determined during supplier site visits or upon review of tank technical information that additional tank over-pressure protection is required to comply with CGA P-59, Prevention of Over-Pressure During Filling of Cryogenic Vessels, the Contractor shall provide and install the additional tank protection which may encompass any of the methods identified in the P-59. NOTE:

Over-protection devices shall not be installed on Government-owned storage tanks without prior coordination with DLA Energy-FEM and the activity that physically possesses the tank(s).

7. INSPECTION AND ACCEPTANCE: Inspection for quality shall be performed at origin. Quantity determination and acceptance shall be at destination.

8. METHOD OF MEASUREMENT: Quantity determination to be performed at delivery location by use of a truck mounted calibrated flow meter.

SPE601-15-R-0308 ABO and LN2Multiple Locations

9. HOT FILLS: Occasionally, the Contractor may be required to perform a “Hot Fill” in order to cool-down and refill any tank that has gone empty and is warm.

10. SECURITY REQUIREMENTS: The Contractor’s driver must have all paperwork associated with delivery, valid driver’s license, and proof of insurance.

Stewart ANG, NY

Energy), as the Department of Defense (DoD) Integrated Materiel Manager (IMM) for Aerospace Energy products and related services, requires delivery of Aviator’s Breathing Oxygen (ABO). The Contractor shall provide all materials, supplies, product, management, tools, equipment, transportation and labor necessary to deliver product f.o.b. destination into Contractor-provided tanks at Stewart ANG, NY.

2. PRODUCT SPECIFICATIONS:

2.1 ABO (NSN 6830-00-808-9531) shall meet the requirements of Type II of specification MIL-PRF-27210J, dated 7 Aug 2013.

2.1.1 MIL-PRF-27210J, paragraph 4.2.1: Preproduction samples are not required if the Contractor’s fill point is already supplying one or more DoD locations with ABO in accordance with all the requirements of MIL-PRF-27210J, including the requirement for submitting periodic samples to a Government approved laboratory listed below in paragraph 2.1.5 “ABO Sample Submission Table”.

2.1.2 MIL-PRF-27210J, paragraph 4.2.2: Preproduction samples (if required) and all periodic sample submissions shall be submitted at the Contractor’s expense to a laboratory listed below in paragraph 2.1.5, “ABO Sample Submission Table”.

Contractor’s submitting samples shall attach/include a properly prepared DD Form 1222, Request for and Results of Test, with each sample clearly marking them as either a Preproduction and/or a Periodic Sample. The submitting Contractor shall also arrange return shipment of the sample containers from the assigned Government laboratory.

2.1.3 MIL-PRF-27210J, paragraph 4.3.1.2: A representative sample of Type II may also be obtained by withdrawing a sample from the sampling port on the shipping container directly into the analytical instrument(s).

2.1.4 The entire contents of a Type II ABO shipping conveyance offered for acceptance by the Government should be produced from a facility that meets all of the requirements of this Statement of Objectives. If the shipping conveyance contains any liquid product that was not produced from an approved facility (such as a product heel from a different fill point), a representative sample shall be drawn from the conveyance (after filling) and

SPE601-15-R-0308 ABO and LN2Multiple Locations that specific timeframe by the appointed Ordering Officer. The individual orders placed by the appointed Ordering Officer will designate the specific quantity to be delivered at the customer location specified in the contract.

4. PRODUCT DELIVERY:

4.1 Product shall be delivered within 7 days after receipt of an order from the appointed Delivery Scheduler. No emergency deliveries are anticipated.

4.2 Deliveries shall be made from 0700-1500 hours, Monday-Friday, excluding federal holidays.

4.3 Product deliveries shall be made to the following address:

ABO SAMPLE SUBMISSION TABLE

PRODUCTION AND PERIODIC

SAMPLES:

AR, CT, DE, IL, IN, IA, KS, KY, ME, MD, MA, MI, MN, MO,

NE, NH, NJ, NY, NC, ND, OH, OK, PA, RI, TN, TX, VT, VA,

WV, WI

Aerospace Fuels Laboratory (FP2070)

AFPA/PTPLA

2430 C Street Bldg 70 Area B Wright-Patterson AFB OH 45433-7632

PH (937)255-2946

AK, AZ, CA, CO, ID, MT, ND, NV, NM, OR, UT, WA, WY Aerospace Fuels Laboratory (FP2075)

AFPA/PTPLE

1747 Utah Ave Bldg 6670 Vandenberg AFB CA 93437-5220

PH (805)606-5873

AL, FL, GA, LA, MS, SC Aerospace Fuels Laboratory (FP2078)

AFPA /PTPLH

15251 Scrub Jay Street Bldg 54800 Cape Canaveral AFS FL 32920

PH (321)85

Or Navair Depot Jacksonville Materials Engineering Lab Code 4.9.7.5

SPE601-15-R-0308 ABO and LN2Multiple Locations

Stewart ANG 1 Maguire Way Newburgh, New York 12550-5075

5. DESCRIPTION OF CONTRACTOR-PROVIDED ABO TANKS: The Contractor shall provide the following ABO bulk storage tanks:

Location Tank Capacity-Gallons Bldg 403 1 - 3,000-5,000 GL

1 – 1,500-2,000 GL

6. INSTALLATION, MAINTENANCE AND REMOVAL OF CONTRACTOR-PROVIDED

TANKS AND EQUIPMENT: Contractor shall install their Contractor-provided tanks/equipment on existing cement pads, within the existing system footprints, no later than 30 calendar days from start of contract performance. The Contractor shall also perform all inspections and maintenance of Contractor-provided tanks/equipment to assure system provides safe and uninterrupted support. Contractor-provided tanks/equipment shall be removed by the Contractor within 30 calendar days after contract termination. Contractor-provided tanks may be chilled through initial deliveries, but initial deliveries into Contractor-provided tanks shall not qualify as a “Hot Fill” service.

The Contractor will coordinate with the current supplier to effect removal of current equipment and installation of new equipment or to change out of existing system or tanks to eliminate any delay in supply of product.

7. TANK PURGE: The DoD tank user will periodically sample the ABO in the Contractor-provided tanks to determine that the product quality meets customer use limits. In the event the ABO does not meet customer use limits, the Contractor shall remove the tank from service and drain the ABO from the tank until empty. Once empty, the Contractor shall purge the tank, using either a liquid or gaseous method, in accordance with tank technical/operations manuals. Following the purging process, the Contractor shall refill the tank with specification ABO and return the tank to service.

8. INSPECTION AND ACCEPTANCE: Inspection for quality shall be performed at origin. Quantity determination and acceptance shall be at destination.

9. METHOD OF MEASUREMENT: Quantity determination to be performed at delivery location by use of a truck mounted calibrated flow meter.

10. SECURITY REQUIREMENTS: All vehicles will stop for a normal security check located at the Commercial Vehicle side which is to the right side of the Main Front Gate.

SPE601-15-R-0308 ABO and LN2Multiple Locations

Stratton ANG, NY

Energy), as the Department of Defense (DoD) Integrated Materiel Manager (IMM) for Aerospace Energy products and related services, requires delivery of Aviator’s Breathing Oxygen (ABO). The Contractor shall provide all materials, supplies, product, management, tools, equipment, transportation and labor necessary to deliver product f.o.b. destination into Government-owned tanks at Stratton ANG, NY.

2. PRODUCT SPECIFICATIONS:

2.1 ABO (NSN 6830-00-808-9531) shall meet the requirements of Type II of specification MIL-PRF-27210J, dated 7 Aug 2013.

2.1.1 MIL-PRF-27210J, paragraph 4.2.1: Preproduction samples are not required if the Contractor’s fill point is already supplying one or more DoD locations with ABO in accordance with all the requirements of MIL-PRF-27210J, including the requirement for submitting periodic samples to a Government approved laboratory listed below in paragraph 2.1.5 “ABO Sample Submission Table”.

2.1.2 MIL-PRF-27210J, paragraph 4.2.2: Preproduction samples (if required) and all periodic sample submissions shall be submitted at the Contractor’s expense to a laboratory listed below in paragraph 2.1.5, “ABO Sample Submission Table”.

Contractor’s submitting samples shall attach/include a properly prepared DD Form 1222, Request for and Results of Test, with each sample clearly marking them as either a Preproduction and/or a Periodic Sample. The submitting Contractor shall also arrange return shipment of the sample containers from the assigned Government laboratory.

2.1.3 MIL-PRF-27210J, paragraph 4.3.1.2: A representative sample of Type II may also be obtained by withdrawing a sample from the sampling port on the shipping container directly into the analytical instrument(s).

2.1.4 The entire contents of a Type II ABO shipping conveyance offered for acceptance by the Government should be produced from a facility that meets all of the requirements of this Statement of Objectives. If the shipping conveyance contains any liquid product that was not produced from an approved facility (such as a product heel from a different fill point), a representative sample shall be drawn from the conveyance (after filling) and tested to determine compliance with the requirements of this Statement of Objectives

PRODUCTION AND PERIODIC

SAMPLES:

SPE601-15-R-0308 ABO and LN2Multiple Locations that specific timeframe by the appointed Ordering Officer. The individual orders placed by the appointed Ordering Officer will designate the specific quantity to be delivered at the customer location specified in the contract.

4. PRODUCT DELIVERY:

4.1 Product deliveries shall be made within 7 days after receipt of an order from the appointed Delivery Scheduler. No emergency deliveries are anticipated.

4.2 Deliveries shall be made from 0700-1600 hours, Monday-Friday, excluding federal holidays.

4.3 Product deliveries shall be made to the following address:

109AW/LGRF, Stratton ANG 1 ANG Rd Scotia, NY 12302

5. DESCRIPTION OF GOVERNMENT-OWNED ABO TANKS: ABO shall be delivered into the following Government-owned storage vessels listed below. The storage vessels will be trailer accessible.

Location Tank Capacity-Gallons MAWP

AR, CT, DE, IL, IN, IA, KS, KY, ME, MD, MA, MI, MN, MO,

NE, NH, NJ, NY, NC, ND, OH, OK, PA, RI, TN, TX, VT, VA,

WV, WI

Aerospace Fuels Laboratory (FP2070)

AFPA/PTPLA

2430 C Street Bldg 70 Area B Wright-Patterson AFB OH 45433-7632

PH (937)255-2946

AK, AZ, CA, CO, ID, MT, ND, NV, NM, OR, UT, WA, WY Aerospace Fuels Laboratory (FP2075)

AFPA/PTPLE

1747 Utah Ave Bldg 6670 Vandenberg AFB CA 93437-5220

PH (805)606-5873

AL, FL, GA, LA, MS, SC Aerospace Fuels Laboratory (FP2078)

AFPA /PTPLH

15251 Scrub Jay Street Bldg 54800 Cape Canaveral AFS FL 32920

PH (321)85

Or Navair Depot Jacksonville Materials Engineering Lab Code 4.9.7.5

SPE601-15-R-0308 ABO and LN2Multiple Locations

Bldg 700 . 3 - 400 GL ea 75 psig ea visits or upon review of tank technical information that additional tank over-pressure protection is required to comply with CGA P-59, Prevention of Over-Pressure During Filling of Cryogenic Vessels, the Contractor shall provide and install the additional tank protection which may encompass any of the methods identified in the P-59. NOTE:

Over-protection devices shall not be installed on Government-owned storage tanks without prior coordination with DLA Energy-FEM and the activity that physically possesses the tank(s).

7. INSPECTION AND ACCEPTANCE: Inspection for quality shall be performed at origin. Quantity determination and acceptance shall be at destination.

8. METHOD OF MEASUREMENT: Quantity determination to be performed at delivery location by use of a truck mounted calibrated flow meter.

9. HOT FILLS: Occasionally, the Contractor may be required to perform a “Hot Fill” in order to cool-down and refill any tank that has gone empty and is warm.

10. SECURITY REQUIREMENTS: The Contractor’s driver must have all paperwork associated with delivery, valid driver’s license, proof of insurance, and will be escorted to the delivery location.

Westhampton Beach ANG, NY

Energy), as the Department of Defense (DoD) Integrated Materiel Manager (IMM) for Aerospace Energy products and related services, requires delivery of Aviator’s Breathing Oxygen (ABO). The Contractor shall provide all materials, supplies, product, management, tools, equipment, transportation and labor necessary to deliver product f.o.b. destination into Government-owned tanks at Westhampton Beach ANG, NY.

2. PRODUCT SPECIFICATIONS:

2.1 ABO (NSN 6830-00-808-9531) shall meet the requirements of Type II of specification MIL-PRF-27210J, dated 7 Aug 2013.

2.1.1 MIL-PRF-27210J, paragraph 4.2.1: Preproduction samples are not required if the Contractor’s fill point is already supplying one or more DoD locations with ABO in accordance with all the requirements of MIL-PRF-27210J, including the requirement for

SPE601-15-R-0308 ABO and LN2Multiple Locations laboratory listed below in paragraph 2.1.5, “ABO Sample Submission Table”.

Contractor’s submitting samples shall attach/include a properly prepared DD Form 1222, Request for and Results of Test, with each sample clearly marking them as either a Preproduction and/or a Periodic Sample. The submitting Contractor shall also arrange return shipment of the sample containers from the assigned Government laboratory.

2.1.3 MIL-PRF-27210J, paragraph 4.3.1.2: A representative sample of Type II may also be obtained by withdrawing a sample from the sampling port on the shipping container directly into the analytical instrument(s).

2.1.4 The entire contents of a Type II ABO shipping conveyance offered for acceptance by the Government should be produced from a facility that meets all of the requirements of this Statement of Objectives. If the shipping conveyance contains any liquid product that was not produced from an approved facility (such as a product heel from a different fill point), a representative sample shall be drawn from the conveyance (after filling) and tested to determine compliance with the requirements of this Statement of Objectives

ABO SAMPLE SUBMISSION TABLE

PRODUCTION AND PERIODIC

SAMPLES:

AR, CT, DE, IL, IN, IA, KS, KY, ME, MD, MA, MI, MN, MO,

NE, NH, NJ, NY, NC, ND, OH, OK, PA, RI, TN, TX, VT, VA,

WV, WI

Aerospace Fuels Laboratory (FP2070)

AFPA/PTPLA

2430 C Street Bldg 70 Area B Wright-Patterson AFB OH 45433-7632

PH (937)255-2946

AK, AZ, CA, CO, ID, MT, ND, NV, NM, OR, UT, WA, WY Aerospace Fuels Laboratory (FP2075)

AFPA/PTPLE

1747 Utah Ave Bldg 6670 Vandenberg AFB CA 93437-5220

PH (805)606-5873

AL, FL, GA, LA, MS, SC Aerospace Fuels Laboratory (FP2078)

AFPA /PTPLH

15251 Scrub Jay Street Bldg 54800 Cape Canaveral AFS FL 32920

PH (321)85

Or Navair Depot Jacksonville Materials Engineering Lab Code 4.9.7.5

SPE601-15-R-0308 ABO and LN2Multiple Locations that specific timeframe by the appointed Ordering Officer. The individual orders placed by the appointed Ordering Officer will designate the specific quantity to be delivered at the customer location specified in the contract.

4. PRODUCT DELIVERY:

4.1 Routine product deliveries shall be made within 7 days after receipt of an order from the appointed Delivery Scheduler. Emergency deliveries shall be made within 2 days after receipt of an order from the appointed Delivery Scheduler

4.2 Deliveries shall be made from 0800-1430 hours, Monday-Friday, excluding federal holidays.

4.3 Product deliveries shall be made to the following address:

106 RQW/LGRF

150 Old Riverhead Road, Building 1305 Westhampton Beach NY 11978

5. DESCRIPTION OF GOVERNMENT-OWNED ABO TANKS: ABO shall be delivered into the following Government-owned storage vessels listed below. The storage vessels will be trailer accessible.

Location Tank Capacity-Gallons MAWP Bldg 1305 1 – 3,000 GL 50 psig 1 – 400 GL 50 psig protection is required to comply with CGA P-59, Prevention of Over-Pressure During Filling of Cryogenic Vessels, the Contractor shall provide and install the additional tank protection which may encompass any of the methods identified in the P-59. NOTE:

Over-protection devices shall not be installed on Government-owned storage tanks without prior coordination with DLA Energy-FEM and the activity that physically possesses the tank(s).

7. INSPECTION AND ACCEPTANCE: Inspection for quality shall be performed at origin. Quantity determination and acceptance shall be at destination.

SPE601-15-R-0308 ABO and LN2Multiple Locations

10. SECURITY REQUIREMENTS: Contractor personnel making deliveries of product will need a valid state driver’s license with proper carrier classifications.

Atlantic City ANG, NJ

Energy), as the Department of Defense (DoD) Integrated Materiel Manager (IMM) for Aerospace Energy products and related services, requires delivery of Aviator’s Breathing Oxygen (ABO) and Liquid Nitrogen (LN2). The Contractor shall provide all materials, supplies, product, management, tools, equipment, transportation and labor necessary to deliver product f.o.b. destination into Government-owned tanks at Atlantic City ANG, NJ.

2. PRODUCT SPECIFICATIONS:

2.1 ABO (NSN 6830-00-808-9531) shall meet the requirements of Type II of specification MIL-PRF-27210J, dated 7 Aug 2013.

2.1.1 MIL-PRF-27210J, paragraph 4.2.1: Preproduction samples are not required if the Contractor’s fill point is already supplying one or more DoD locations with ABO in accordance with all the requirements of MIL-PRF-27210J, including the requirement for submitting periodic samples to a Government approved laboratory listed below in paragraph 2.1.5 “ABO Sample Submission Table”.

2.1.2 MIL-PRF-27210J, paragraph 4.2.2: Preproduction samples (if required) and all periodic sample submissions shall be submitted at the Contractor’s expense to a laboratory listed below in paragraph 2.1.5, “ABO Sample Submission Table”.

Contractor’s submitting samples shall attach/include a properly prepared DD Form 1222, Request for and Results of Test, with each sample clearly marking them as either a Preproduction and/or a Periodic Sample. The submitting Contractor shall also arrange return shipment of the sample containers from the assigned Government laboratory.

SPE601-15-R-0308 ABO and LN2Multiple Locations

2.1.3 MIL-PRF-27210J, paragraph 4.3.1.2: A representative sample of Type II may also be obtained by withdrawing a sample from the sampling port on the shipping container directly into the analytical instrument(s).

2.1.4 The entire contents of a Type II ABO shipping conveyance offered for acceptance by the Government should be produced from a facility that meets all of the requirements of this Statement of Objectives. If the shipping conveyance contains any liquid product that was not produced from an approved facility (such as a product heel from a different fill point), a representative sample shall be drawn from the conveyance (after filling) and

2.3 In addition to the reports required elsewhere within this contract, one copy of a Certificate of Analysis for each sample required by the specification shall be submitted

PRODUCTION AND PERIODIC

SAMPLES:

AR, CT, DE, IL, IN, IA, KS, KY, ME, MD, MA, MI, MN, MO,

NE, NH, NJ, NY, NC, ND, OH, OK, PA, RI, TN, TX, VT, VA,

WV, WI

Aerospace Fuels Laboratory (FP2070)

AFPA/PTPLA

2430 C Street Bldg 70 Area B Wright-Patterson AFB OH 45433-7632

PH (937)255-2946

AK, AZ, CA, CO, ID, MT, ND, NV, NM, OR, UT, WA, WY Aerospace Fuels Laboratory (FP2075)

AFPA/PTPLE

1747 Utah Ave Bldg 6670 Vandenberg AFB CA 93437-5220

PH (805)606-5873

AL, FL, GA, LA, MS, SC Aerospace Fuels Laboratory (FP2078)

AFPA /PTPLH

15251 Scrub Jay Street Bldg 54800 Cape Canaveral AFS FL 32920

PH (321)85

Or Navair Depot Jacksonville Materials Engineering Lab Code 4.9.7.5

SPE601-15-R-0308 ABO and LN2Multiple Locations that specific timeframe by the appointed Ordering Officer. The individual orders placed by the appointed Ordering Officer will designate the specific quantity to be delivered at the customer location specified in the contract.

4. PRODUCT DELIVERY:

4.1. Product shall be delivered within 7 days after receipt of an order from the appointed Delivery Scheduler. No emergency deliveries are anticipated.

4.2 Deliveries shall be made from 0730-1600 hours, Tuesday-Friday, excluding federal holidays.

4.3 Product deliveries shall be made to the following address:

177FW/LGRF Atlantic City ANG Building 470 400 Langley Road Egg Harbor Township, NJ 08234

5. DESCRIPTION OF GOVERNMENT-OWNED ABO & LN2 TANKS: ABO and LN2 shall be delivered into the following Government-owned storage vessels listed below.

The storage vessels will be trailer accessible.

Location Tank Capacity-Gallons MAWP Bldg 470 2 - 3,000 GL ea ABO 55 psig ea 2 - 2,000 GL ea LN2 55 psig ea

6. TANK OVER-PRESSURE PROTECTION: If it is determined during supplier site visits or upon review of tank technical information that additional tank over-pressure protection is required to comply with CGA P-59, Prevention of Over-Pressure During Filling of Cryogenic Vessels, the Contractor shall provide and install the additional tank protection which may encompass any of the methods identified in the P-59. NOTE:

Over-protection devices shall not be installed on Government-owned storage tanks without prior coordination with DLA Energy-FEM and the activity that physically possesses the tank(s).

7. INSPECTION AND ACCEPTANCE: Inspection for quality shall be performed at origin. Quantity determination and acceptance shall be at destination.

8. METHOD OF MEASUREMENT: Quantity determination to be performed at delivery location by use of a truck mounted calibrated flow meter.

SPE601-15-R-0308 ABO and LN2Multiple Locations

10. SECURITY REQUIREMENTS: All deliveries must go through the commercial gate, must have all appropriate paper work for the equipment they are operating including Commercial Driver’s License, insurance, registration and all delivery paperwork for the product.

McGuire AFB, NJ

1. DESCRIPTION OF REQUIREMENT: Defense Logistics Agency Energy (DLA Energy), as the Department of Defense (DoD) Integrated Materiel Manager (IMM) for Aerospace Energy products and related services, requires delivery of Aviator’s Breathing Oxygen (ABO). The Contractor shall provide all materials, supplies, product, management, tools, equipment, transportation and labor necessary to deliver product f.o.b. destination into Government-owned tanks at McGuire AFB, NJ.

2. PRODUCT SPECIFICATIONS:

2.1 ABO (NSN 6830-00-808-9531) shall meet the requirements of Type II of specification MIL-PRF-27210J, dated 7 Aug 2013.

2.1.1 MIL-PRF-27210J, paragraph 4.2.1: Preproduction samples are not required if the Contractor’s fill point is already supplying one or more DoD locations with ABO in accordance with all the requirements of MIL-PRF-27210J, including the requirement for submitting periodic samples to a Government approved laboratory listed below in paragraph 2.1.5 “ABO Sample Submission Table”.

2.1.2 MIL-PRF-27210J, paragraph 4.2.2: Preproduction samples (if required) and all periodic sample submissions shall be submitted at the Contractor’s expense to a laboratory listed below in paragraph 2.1.5, “ABO Sample Submission Table”.

Contractor’s submitting samples shall attach/include a properly prepared DD Form 1222, Request for and Results of Test, with each sample clearly marking them as either a directly into the analytical instrument(s).

2.1.4 The entire contents of a Type II ABO shipping conveyance offered for acceptance by the Government should be produced from a facility that meets all of the requirements of this Statement of Objectives. If the shipping conveyance contains any liquid product that was not produced from an approved facility (such as a product heel from a different fill point), a representative sample shall be drawn from the conveyance (after filling) and

SPE601-15-R-0308 ABO and LN2Multiple Locations that specific timeframe by the appointed Ordering Officer. The individual orders placed by the appointed Ordering Officer will designate the specific quantity to be delivered at the customer location specified in the contract.

4. PRODUCT DELIVERY:

4.1 Product shall be delivered within 7 days after receipt of an order from the appointed Delivery Scheduler. No emergency deliveries are anticipated.

4.2 Deliveries shall be made from 0900-1400 hours, Monday-Friday, excluding federal

PRODUCTION AND PERIODIC

SAMPLES:

AR, CT, DE, IL, IN, IA, KS, KY, ME, MD, MA, MI, MN, MO,

NE, NH, NJ, NY, NC, ND, OH, OK, PA, RI, TN, TX, VT, VA,

WV, WI

Aerospace Fuels Laboratory (FP2070)

AFPA/PTPLA

2430 C Street Bldg 70 Area B Wright-Patterson AFB OH 45433-7632

PH (937)255-2946

AK, AZ, CA, CO, ID, MT, ND, NV, NM, OR, UT, WA, WY Aerospace Fuels Laboratory (FP2075)

AFPA/PTPLE

1747 Utah Ave Bldg 6670 Vandenberg AFB CA 93437-5220

PH (805)606-5873

AL, FL, GA, LA, MS, SC Aerospace Fuels Laboratory (FP2078)

AFPA /PTPLH

15251 Scrub Jay Street Bldg 54800 Cape Canaveral AFS FL 32920

PH (321)85

Or Navair Depot Jacksonville Materials Engineering Lab Code 4.9.7.5

SPE601-15-R-0308 ABO and LN2Multiple Locations

305 AMW/LGRF

3101 Vandenberg Ave., Bldg 1839 McGuire AFB, NJ 08641-5102

5. DESCRIPTION OF GOVERNMENT-OWNED ABO TANKS: ABO shall be delivered into the following Government-owned storage vessels listed below. The storage vessels will be trailer accessible.

Location Tank Capacity-Gallons MAWP Bldg…