PID_PACK.docx

*** LTC PID Packaging Consolidated Text *** PLEASE SEE GLOSSARY AT THE END OF THE DOCUMENT FOR FULL TEXT OF THE ITEM DESCRIPTION

AND PACKAGING REFERENCE NUMBERS CALLED OUT FOR EACH NSN.

NSN:011008296

VALVE, REFUELING

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RQ001

REFERENCE NUMBER:RQ001

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RQ011

SIKORSKY AIRCRAFT CORP,CAGE: 78286

P/N: 70307-03030-103

REFERENCE NUMBER:ZD080

APPROVED SOURCE:

EATON CORPORATION

DBA AEROSPACE DIV

DIV CONVEYANCE SYSTEM

CAGE: 00624

P/N: AE80613P

REFERENCE NUMBER:A0003

REFERENCE NUMBER:CS001

CRITICAL APPLICATION ITEM

EATON-AEROQUIP LLC. DBA Aerospace 00624 P/N AE80613P

IAW BASIC DRAWING NR 78286 70307-03030

REVISION NR H DTD 11/07/2013

PART PIECE NUMBER: 70307-03030-103

IAW REFERENCE DRAWING NR 78286 70307-03030

REVISION NR G DTD 04/08/1999

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 78286 70307-03030-103

REVISION NR H DTD 11/26/2012

PART PIECE NUMBER:

PREP FOR DELIVERY

LINE ITEM 00001 TYPE OF COVERAGE: CUSTOMER DIRECT, CONUS

PKGING DATA-QUP:001

SHALL BE PACKAGED IN ACCORDANCE WITH ASTM D 3951.

GLOSSARY

PACKAGING TEXT

THE FOLLOWING PARAGRAPH APPLIES TO ALL PACKAGING CALLED OUT IN THIS DOCUMENT:

Markings Paragraph When ASTM D3951, Commercial Packaging is specified, the following apply:

•,,All Section “D” Packaging and Marking Clauses take precedence over

ASTM D3951.

•,,In addition to requirements in MIL-STD-129, when Commercial Packaging is used, the Method of Preservation for all MIL-STD-129 marking and labeling shall be “CP” Commercial Pack.

•,,The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) as specified in the contract take precedence over QUP in ASTM D3951.

ITEM DESCRIPTION TEXT

REFERENCE NUMBER RP001

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

REFERENCE NUMBER RQ001

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND

NON-MANUFACTURERS)

REFERENCE NUMBER RA001

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB

AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR

SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

REFERENCE NUMBER RQ011

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

REFERENCE NUMBER ZD080

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

REFERENCE NUMBER A0003

MIL-STD-130N(1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

REFERENCE NUMBER CS001

This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms Regulations (ITAR) or the Export Administration Regulations (EAR) and cannot be exported without the authorization of either the Department of State or the Department of Commerce prior to export. Export includes disclosure of technical data to foreign nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees or U.S. companies and their foreign subsidiaries.

DLA has enhanced its Joint Certification Program (JCP) registration and validation procedures. Selected National Stock Numbers (NSNs) will require additional permissions to access the associated technical data.

In the event a vendor cannot access the technical data for a NSN in DLA cFolders, the vendor must submit a onetime request to jcpvalidation@dla.mil for technical data access consideration. If a vendor has inquiries after having submitted required information to the JCP office, these inquiries are to be directed to DLAJ344DataCustodian@dla.mil.

DLA processes the vendor's technical data request on a first come, first served basis. Failure to comply timely with required information may result in lack of consideration for DLA solicitations. It is vitally important that vendors provide correct company official name(s) and contact information in all correspondence. DLA will work diligently on validating vendor requests. Vendors will be notified within 3 business days of when their requests were approved. However, DLA cannot guarantee that it can complete all validation requests by the due date for any solicitation responses.