Safety Tester TechSpecsSOW.pdf
PDF 145 KB Posted
- Attached to
- Safety Test Equipment (presolicitation synopsis)
- Solicitation number
- SP470624Q0024
- Issued by
-
Defense Logistics Agency
About this file
This document is a Technical Specifications Statement of Work (SOW) for an Automated AC/DC DWV/IR Test System for the Defense Logistics Agency (DLA) Product Test Center in Columbus, Ohio. The SOW specifies the salient characteristics required for the test system, including a Vitrek Corporation 951i 6KV AC/DC IR/LR Electrical Safety Compliance Analyzer or equivalent, required upgrades and accessories, and delivery requirements. The instrument must be new, with a NIST-traceable calibration certificate, and delivered within 30 days of the award. The contract will be awarded by the DLA, with Kyle Palmer as the Contracting Officer Representative (COR) and Larry Baas as the Technical Representative. Invoices must be submitted through the Wide Area Workflow (WAWF) system. This SOW is related to a pre-solicitation synopsis for Safety Test Equipment, Solicitation Number SP470624Q0024, which will be formally solicited at a later date.
View the file
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Rev 04/10/2024
Technical Specifications
Automated AC/DC DWV/IR Test System
DLA Product Test Center, VTP
I. The contractor shall provide all labor, materials, tools, transportation, supplies, supervision, etc. (except as noted), necessary to provide all components for an Automated AC/DC DWV/IR Test System to the Defense Supply Center Columbus (DSCC), Columbus, Ohio. The salient characteristics of the Automated AC/DC DWV/IR Test System are as listed below:
A. Vitrek Corporation, 951i 6KV AC/DCIR/LR Electrical Safety Compliance Analyzer, Brand Name or Equal with the following salient characteristics:
1. Shall be new, not refurbished.
2. Shall be supplied with Operating manual.
3. Shall have; Resolution of at least 0.1V up to 6kV.
4. Shall be capable of measurements for: AC-DWV, DC-DWV, IR, 2-wire and 4-wire resistance (upto 100kΩ)
5. Shall at a minimum have: Accuracy of at least 0.25% + 0.5V.
6. Shall at a minimum have: Measurement period of 1 power line cycle (50/60Hz).
7. Shall have: Discharge rate of 25mA in solid-state constant current discharge mode.
8. Shall have: NIST Traceable Calibration Certificate and ISO 17025 accredited calibration certificate with data and uncertainties
9. Shall at a minimum have: Included Accessories: Power cord and HV/Continuity Test Lead set
B. Required Upgrades and Accessories - Brand Name or Equal:
1. GPIB Interface for the 950i Series. (Vitrek: ISO-CALN-95X or equivalent)
2. High Voltage Switching System Mainframe (8 card capacity)including: Serial Port, VICL Cable, MCS-964
Mating Connectors, External power source with power cord, Operator’s manual, and Certificate of Compliance. (Vitrek: 964i (Configuration # 1028A) or equivalent)
3. 7KV Single (+) Input Bus 8 Outputs, White HV Terminals. (Vitrek: HV7-8W or equivalent)
4. 8 Channel 7KV Relay card “Internal Y”. (Vitrek: HV7-8Y or equivalent)
5. GPIB Interface. (Vitrek: GP-964 or equivalent)
6. 951i Output 2-way Breakout Box Lead Set. (Vitrek: TL-BK2 or equivalent)
7. QTPro-II permanent software license
8. 64 HV cables (4 feet length each) with covered alligator clip and banana plug terminations
C. Place of Performance
The instrument shall be delivered to:
Defense Supply Center Columbus 300 North James Road, Bldg 17-3 Mark for: DLA Product Test Center, Bldg 11-7 (TE Lab) Attn: Eric Kelly (eric.kelly@dla.mil / 614-692-9862) Columbus, Ohio 43213
D. Travel (if applicable) N/A
E. Invoicing mailto:eric.kelly@dla.mil
Rev 04/10/2024
Technical Specifications
Automated AC/DC DWV/IR Test System
DLA Product Test Center, VTP
Payment of invoices will be accomplished by payment through the Defense Finance and Accounting Service.
Invoices will be submitted to the Wide Area Workflow (WAWF) system in accordance with DFARS 252.232-7003 Electronic Submission of Payment Requests and Receiving Reports and DFARS 252.232-7006 Wide Area Workflow Payment Instructions within 10 workdays after the conclusion of each training session.
F. WAWF Acceptance DODAAC#
1. TA Lab is SL0700.
G. Other Requirements:
1. Delivery: 30 days from date of the award.
2. Contractor shall give notification to Eric Kelly (eric.kelly@dla.mil /614-692-9862) when the instrument is ready to be delivered.
3. All shipping costs are to be included in the contracted price.
4. The instrument shall be delivered to:
Defense Supply Center Columbus 300 North James Road, Bldg 17-3 Mark for: DLA Product Test Center, Bldg 11-7 (TE Lab) Attn: Eric Kelly (eric.kelly@dla.mil / 614-692-9862) Columbus, Ohio 43213
5. Invoices shall be submitted through Wide Area Workflow (WAWF), See DFARS Clause 252.232-7006
Wide Area Workflow Payment Instructions for detailed instructions on how to submit invoices.
H. Points of Contact The Government Contract Officer:
TBD
The Government Contract Officer Representative (COR):
Kyle Palmer Kyle.palmer@dla.mil
(614) 692-8860
DLA Land & Maritime Product Test Center, 3990 E. Broad St., Columbus OH, Bldg. 11, Section 7 Larry Baas (614) 692-9893
The Government Technical Representative
Name: Larry Baas Phone #: (614) 692-9893 Email: larry.baas@dla.mil mailto:Kyle.palmer@dla.mil
File details come from the government source that posted it. Updated .