N68335-15-R-0135_Ammendment_0002.doc

N68335-15-R-0135

SECTION SF 30 BLOCK 14 CONTINUATION PAGE

SUMMARY OF CHANGES

SECTION SF 30 - BLOCK 14 CONTINUATION PAGE

The following have been added by full text:

AMMEND 0002

The purpose of this ammendment is to:

1. Clarify Pre-production unit requirements and hereby incorporate a revised Statement of Work into Section J.

2. Hereby incorporate a revised Performance Specification into section J.

3. The summary of changes is as follows:

Statement of Work

The Statement of Work, page 19, paragraph 4.3 has changed from:

The Contractor shall produce a maximum of four PPUs for use during PPT and the PPUs shall be calibrated by the Contractor prior to PPT I. Additionally, any follow-on calibration required during the testing phase PPAT, PPT I, PPT II, Independent Government Testing, and PAT shall also be performed by the Contractor. All PPUs shall undergo all PPT I which encompasses PPAT. A number of PPUs specified by the Government will be shipped to Naval Air Warfare Center Aircraft Division, 22763 Saufley Rd, Building 1405, Patuxent River, MD 20670, 360 DACA for Independent Government Testing while PPT II is ongoing. The Contractor is required to complete CTR prior to shipment of these units. These PCPLTs, along with the technical data package, will represent the intended Final Product Baseline and will serve as models to which all production PCPLTs will be built. Upon completion of testing the Contractor shall refurbish the PPUs to production level standards.

To:

The Contractor shall produce a maximum of five PPUs for use during PPT and the PPUs shall be calibrated by the Contractor prior to PPT I. Additionally, any follow-on calibration required during the testing phase PPAT, PPT I, PPT II, Independent Government Testing, and PAT shall also be performed by the Contractor. All PPUs shall undergo all PPT I which encompasses PPAT. A number of PPUs specified by the Government will be shipped to Naval Air Warfare Center Aircraft Division, 22763 Saufley Rd, Building 1405, Patuxent River, MD 20670, 360 DACA for Independent Government Testing while PPT II is ongoing. The Contractor is required to complete CTR prior to shipment of these units. These PCPLTs, along with the technical data package, will represent the intended Final Product Baseline and will serve as models to which all production PCPLTs will be built. Upon completion of testing the Contractor shall refurbish the PPUs to production level standards.

The Statement of Work, page 9, paragraph 3.3.3 has changed from:

Entrance Criteria

· Meeting/Review Agendas (CDRL A002)

· Meeting/Review Presentations (CDRL A003)

· Submittal of updated Drawing Tree/Top Down Breakdown (CDRL A010)

· Submittal of an Engineering Drawing Package (CDRL A011)

· Submittal of Requirements Traceability Matrix (A013)

· Submittal of the System Safety Hazard Analysis Report (CDRL A014)

· Submittal of the HMMP Report (CDRL A016)

· Submittal of the Reliability Prediction Report (CDRL A017)

· Submittal of the Maintainability Predictions Report (CDRL A018)

· Submittal of the Master Test Plan (CDRL T001)

· Submittal of the Pilot Production Acceptance Test Procedures (CDRL T004)

· Submittal of the Pilot Production Test (PPT) I Procedures (CDRL T006)

· Submittal of the Shock Test Plan (CDRL T010)

· Submittal of the SAD (CDRL LB03)

· Submittal of the CMRS Report (CDRL LC02)

· Submittal of the Statement of Prior Submission (SPS) (CDRL LP01)

· Submittal of the Supplemental Data for Provisioning (SDFP) (CDRL LP02)

· Submittal of the Long Lead Time Items List (LLTIL) for Production (CDRL LS01)

· Submittal of TM for Second Review (CDRL LT02)

To:

Entrance Criteria

· Meeting/Review Agendas (CDRL A002)

· Meeting/Review Presentations (CDRL A003)

· Submittal of updated Drawing Tree/Top Down Breakdown (CDRL A010)

· Submittal of an Engineering Drawing Package (CDRL A011)

· Submittal of Requirements Traceability Matrix (A013)

· Submittal of 3-D Models (CDRL A019)

· Submittal of the System Safety Hazard Analysis Report (CDRL A014)

· Submittal of the HMMP Report (CDRL A016)

· Submittal of the Reliability Prediction Report (CDRL A017)

· Submittal of the Maintainability Predictions Report (CDRL A018)

· Submittal of the Master Test Plan (CDRL T001)

· Submittal of the Pilot Production Acceptance Test Procedures (CDRL T004)

· Submittal of the Pilot Production Test (PPT) I Procedures (CDRL T006)

· Submittal of the Shock Test Plan (CDRL T010)

· Submittal of the SAD (CDRL LB03)

· Submittal of the CMRS Report (CDRL LC02)

· Submittal of the Statement of Prior Submission (SPS) (CDRL LP01)

· Submittal of the Supplemental Data for Provisioning (SDFP) (CDRL LP02)

· Submittal of the Long Lead Time Items List (LLTIL) for Production (CDRL LS01)

· Submittal of TM for Second Review (CDRL LT02)

The Statement of Work, page 10, paragraph 3.3.4 has changed from:

Entrance Criteria

· Meeting/Review Agendas (CDRL A002)

· Meeting/Review Presentations (CDRL A003)

· Presentation shall include a detailed discussion of any changes to the initial product baseline that was established at the CDR.

· Submittal of updated Engineering Drawing Package (CDRL A011)

· Submittal of updated requirements traceability matrix (CDRL A013)

· Approved Failure Reporting, Analysis, and Corrective Action System Plan (CDRL T002)

· Approved Pilot Production Acceptance Test Report (CDRL T005)

· Approved PPT I Report (CDRL T007)

· Approved PPT II Procedures (CDRL T008)

· Approved Maintainability Demonstration (MDEMO) Test Plan (CDRL T013)

· Submittal of the Test Materials List (CDRL T015)

· All required test resources (people, facilities, test articles, test instrumentation) are identified and are available for testing

· Submittal of the SAD (CDRL LB03)

· Submittal of the Preliminary Interim Support Items List (ISIL) (LS02)

· Submittal of TM for Third Review (CDRL LT02)

· Submittal of Training Materials (CDRLs LTR01 & LTR02)

To:

Entrance Criteria

· Meeting/Review Agendas (CDRL A002)

· Meeting/Review Presentations (CDRL A003)

· Presentation shall include a detailed discussion of any changes to the initial product baseline that was established at the CDR.

· Submittal of updated Engineering Drawing Package (CDRL A011)

· Submittal of updated requirements traceability matrix (CDRL A013)

· Submittal of updated 3-D Models (A019)

· Approved Failure Reporting, Analysis, and Corrective Action System Plan (CDRL T002)

· Approved Pilot Production Acceptance Test Report (CDRL T005)

· Approved PPT I Report (CDRL T007)

· Approved PPT II Procedures (CDRL T008)

· Approved Maintainability Demonstration (MDEMO) Test Plan (CDRL T013)

· Submittal of the Test Materials List (CDRL T015)

· All required test resources (people, facilities, test articles, test instrumentation) are identified and are available for testing

· Submittal of the SAD (CDRL LB03)

· Submittal of the Preliminary Interim Support Items List (ISIL) (LS02)

· Submittal of TM for Third Review (CDRL LT02)

· Submittal of Training Materials (CDRLs LTR01 & LTR02)

Statement of Work

The Statement of Work, page 11, paragraph 3.3.5 has changed from:

Entrance Criteria

· Meeting/Review Agendas (CDRL A002)

· Meeting/Review Presentations (CDRL A003)

· Submittal of Physical Configuration Audit Plan (CDRL A007)

· Submittal of an updated Drawing Tree (CDRL A010)

· Approved Pilot Production Test II Report (CDRL T009)

· Submittal of the Shock Test Report (CDRL T011)

· Submittal of the MDEMO Test Report (CDRL T014)

· Submittal of the Production Acceptance Test Procedures (CDRL T017)

· Submittal of the SAD (CDRL LB03)

· Submittal of the Final ICP Source Data (CDRL LC01)

· Submittal of the SDFP (CDRL LP02)

· Submittal of the Final ISIL (LS02)

· Submittal of an updated complete TM (CDRL LT02)

· Submittal of the Contractor Validation Plan (CDRL LT04) To:

Entrance Criteria

· Meeting/Review Agendas (CDRL A002)

· Meeting/Review Presentations (CDRL A003)

· Submittal of Physical Configuration Audit Plan (CDRL A007)

· Submittal of an updated Drawing Tree (CDRL A010)

· Submittal of updated Engineering Drawing Package (CDRL A011)

· Submittal of updated 3-D Models (A019)

· Approved Pilot Production Test II Report (CDRL T009)

· Submittal of the Shock Test Report (CDRL T011)

· Submittal of the MDEMO Test Report (CDRL T014)

· Submittal of the Production Acceptance Test Procedures (CDRL T017)

· Submittal of the SAD (CDRL LB03)

· Submittal of the Final ICP Source Data (CDRL LC01)

· Submittal of the SDFP (CDRL LP02)

· Submittal of the Final ISIL (LS02)

· Submittal of an updated complete TM (CDRL LT02)

· Submittal of the Contractor Validation Plan (CDRL LT04) PCPLT System Specification

The Spec, page 2, paragraph 2.2 has changed from:

Drawings

To:

Drawings

The Spec, page 8, Table 1 has changed from:

Table 1 - Accessories

Table 2 - Accessories

CDRL Matrix page 1 has changed from:

DACA

DACA

DACA

DACA

DACA

Admin/ Technical

X

X

X

X

X

X

X

X

X

X

X

Testing

X

X

AS REQ

X

X

X

X

X

DACA

DACA

DACA

DACA

Admin/ Technical

X

X

X

X

X

X

X

X

X

X

Testing

X

X

AS REQ

X

X

X

X

X

X

X

X

X

X

X

X

AS REQ

X

X

Logistics

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

PCPLT CDRL A019 has changed from:

CONTRACT DATA REQUIREMENTS LIST (1 Data Item)

Form Approved OMB No. 0704-0188

Public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for information Operations and reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project, (0704-0188), Washington, DC 20503. Please DO NOT RETURN your form to either of these addresses. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

DISTRIBUTION

DD

b. COPIES

Final

A

Block 7: Final submittal DD250 (DD)

Block 8: Allow 30 calendar days for Government approval/disapproval. Revisions, if required, shall be submitted no later than 15 calendar days after receipt of Government comments.

Blocks 10 & 12: Submit 15 days prior to CTR

Block 14: “E” means Electronic Copy

Submit as .iges file type

See CDRL Matrix for submission timeframe (DACA).

DESTINATION OF DELIVERABLES

Naval Air Warfare Center Aircraft Division, Route 547, Lakehurst, NJ 08733

DD Form 1423-2 Sep 90 Previous editions are obsolete

CONTRACT DATA REQUIREMENTS LIST (1 Data Item)

Form Approved OMB No. 0704-0188

Public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for information Operations and reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project, (0704-0188), Washington, DC 20503. Please DO NOT RETURN your form to either of these addresses. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

DISTRIBUTION

DD

b. COPIES

Final

A

Block 7: Final submittal DD250 (DD)

Block 8: Allow 30 calendar days for Government approval/disapproval. Revisions, if required, shall be submitted no later than 15 calendar days after receipt of Government comments.

Blocks 10, 12 & 13: Submit drawing package representing the proposed pilot production units 15 calendar days prior to the CDR, submit complete drawings 15 days prior to CTR, update 15 days prior to SVR/PRR and Final drawings will be delivered 30 days after PCA (or with first production unit if PCA is not implemented)

Block 14: “E” means Electronic Copy

Submit as .step file type

See CDRL Matrix for submission timeframe (DACA).

DESTINATION OF DELIVERABLES

Naval Air Warfare Center Aircraft Division, Route 547, Lakehurst, NJ 08733

DD Form 1423-2 Sep 90 Previous editions are obsolete

4. All other terms and conditions remain unchanged.

SECTION J - LIST OF DOCUMENTS, EXHIBITS AND OTHER ATTACHMENTS

The following have been modified:

LIST OF ATTACHMENTS

DOCUMENT TYPE

DESCRIPTION

PAGES

DATE

Exhibit A, T

Contract Data Requirements List

26 February 2015

Exhibit L

ILS Contract Data Requirements List 26 February 2015

Attachment 1

Pneumatic Cabin Pressure Leakage Tester

Performance Specification

49 30 October 2015

Attachment 2

Pneumatic Cabin Pressure Leakage Tester

Engineering Statement of Work

30 October 2015

(End of Summary of Changes)