Attachment_2_GRSP_SPEC_1.2.docx

M67854-15-Q-7818 Date: 20 Jul 2015 M67854-15-R-7818

Attachment 2 Performance Specification For

Range Training Systems (RTS) Ground Range Sustainment Program (GRSP)

Version 1.2 20 Jul 2015

MARINE CORPS SYSTEMS COMMAND

PROGRAM MANAGER, TRAINING SYSTEMS

12211 SCIENCE DRIVE, ORLANDO, FL 32826-3275

ii

Performance Specification For Range Training Systems (RTS) Ground Range Sustainment Program (GRSP)

SCOPE

This is the performance specification for the Ground Range Sustainment Program.

APPLICABLE DOCUMENTS

General The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed.

Government Documents Specifications, standards, and handbooks.

The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

(Copies of these documents are available online at http://quicksearch.dla.mil.)

Non-Government Publications The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

Order of precedence Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

REQUIREMENTS

General Specific requirements for delivery, assembly and installation are addressed in section 3.1 of the Performance Work Statement.

Moving Personnel Targets Each Moving Personnel Targets (MPT) shall include a mover.

Each MPT shall include a Radio Frequency (RF) wireless remote control.

Each MPT shall include a 3-D torso target.

Each MPT shall include a charger.

If the remote controls require a charger, the MPT shall include a remote charger.

The RF MPT shall be Federal Communications Commission - FCC Part 15 certified.

MPT Mover The MPT mover shall carry the included 3-D torso target. The MPT mover shall include mounts to carry 2D plastic and paper Echo Silhouette targets.

The MPT mover shall have a rechargeable battery.

The MPT shall drive forward and backward on command.

The MPT shall turn left and right on command.

The MPT shall have a turns 360° on its own radius.

The MPT shall traverse even terrain such as hard packed, paved and concrete areas.

The MPT shall traverse uneven terrain such as grass, dirt, gravel training areas.

The MPT shall traverse all terrains up to a positive 10 degree slope.

The MPT shall traverse all terrains up to a negative 10 degree slope.

The MPT shall score effectively on various terrain.

The MPT shall have adjustable speeds up to 10 feet per second on concrete.

The MPT shall have adjustable speeds from 0-6mph in the forward direction on all other required terrains.

The MPT shall be transportable via commercial vehicles such as midsize pickup, van, or military High Mobility Multipurpose Wheeled Vehicle (HMMWV).

The MPT shall be a two person lift in accordance with Mil Standard 1472.

The MPT shall have weight and lifting warning stickers in accordance with MIL-STD-882.

The MPT shall be ballistically protected against 5.56mm and 7.62mm rounds.

The MPT shall operate in all weather conditions such as rain and snow.

MPT Target The MPT Target shall mount to the MPT mover.

The MPT 3D target shall be 5 to 6 Feet tall and representative of a male upper torso.

MPT Hit Detection and Reaction The MPT shall detect 5.56mm firearm hits. The MPT shall detect 7.62mm firearm hits.

The MPT shall automatically react to hits. The MPT shall automatically stop on hit detection. The MPT shall automatically reset after a designated time period set by the controller.

The MPT shall include controls to remotely reset the target and resume movement after a hit.

MPT Controller The MPT shall be controlled via wireless laptop or hand held controller.

The MPT controller shall control the MPT mover.

The MPT controller shall be wireless.

The MPT controller shall allow the operator to adjust the MPT speed from 0 to the maximum speed for a terrain.

The MPT controller shall work at all distances up to and including 1000 meters line of sight.

If the MPT does not automatically reset after hit detection, the MPT controller shall include controls to restart motion after the MPT has stopped due to hit detection.

The MPT controller shall be water resistant equivalent to IP 63.

The MPT controller shall operate in all weather conditions.

Lightweight Non Live Fire Structure The Lightweight Non Live Fire Structure (LWNLFS) shall be modular.

The LWNLFS shall be non-permanent.

The LWNLFS shall be reconfigurable.

The LWNLFS shall be re-locatable.

The LWNLFS shall include all parts and tools needed for assembly.

The LWNLFS shall be fully enclosed when assembled.

LWNLFS shall include walls.

LWNLFS shall include a ceiling/roof.

LWNLFS shall include floor panels.

LWNLFS shall include a door.

LWNLFS shall include a window. The window shall be shatterproof.

The LWNLFS shall withstand Special Effects Small Arms Marking System (SESAMS) ammunition.

The LWNFS shall be configurable to simulate buildings, villages, and farm houses on the Live Fire and Maneuver (LFAM ) Training Site.

The LWNLFS shall be man portable.

The LWNLFS shall be easily assembled or disassembled.

The LWNLFS shall be constructed of environmentally friendly materials.

The LWNLFS floor shall have footers 3 - 4 inches above the ground to minimize earth exposure.

The LWNLFS shall have interchangeable panels to form a variety of configurations.

The LWNLFS shall have a minimum 6 foot tall entry door.

The LWNLFS shall be weatherproof.

The LWNLFS shall be supplied with stakes or anchoring system for earthen environment.

The LWNLFS shall be desert sand color.

Fighting Hole Covers The fighting hole covers shall be made from molded plastic.

The fighting hole covers shall prevent water and dirt from entering the fire holes.

The fighting hole covers shall be sturdy enough to withstand the weather elements.

The fighting hole covers shall include tie down and strap inserts as depicted in figure 1.

The tie downs and straps shall be sufficient to keep the fighting hole covers from being blown away by wind speed up to 130 MPH.

The fighting hole covers shall be olive drab (green).

The Range F5 covers shall have a 52" internal diameter (ID) and 58" outer diameter (OD).

The Range K‐509 covers shall have a 100" ID and 114" OD.

Figure 1: Fighting Hole Cover with Tie Down Target Turning System The Target Turning System (TTS) shall comprise of a heavy duty target turner.

The TTS shall mount to existing heavy duty target carriages (HDTC) on the rifle ranges.

The TTS shall be appropriately sized to mount to the HDTCs (which will require it to be approximately 26” in length) The TTS shall be constructed of Hot Rolled Steel (HRS) The TTS shall have a hot-dip galvanized finish.

The TTS shall lock onto the carriage using stainless steel lever lock in three points.

The TTS shall have an internal square tube to hold a standard 2”x 2” stick with a target attached to it.

The TTS shall allow the operator to manually actuate the target 90 degrees on the vertical axis. The TTS shall be easy to actuate using a single hand.

The TTS shall expose the target at one extreme of its actuation. The TTS shall conceal the target at the other extreme of its actuation. The TTS shall not leave the exposed position until actuated by the operator. The TTS shall not leave the concealed position until actuated by the operator.

The TTS shall be actuated by a single operator’s hand twist of the inner tube via a stainless steel handle.

The TTS shall not be damaged by actuation. The TTS shall be free of grease and oil. The TTS shall be maintenance-free.

Bleacher Replacement Bleachers shall have all-aluminum framework.

Bleachers shall measure 4’ (Height) x 21’ (Length).

Bleachers shall be anodized to resist corrosion.

Bleachers shall have 5 rows of aluminum seat planks. Bleachers shall have at least 4 rows of aluminum foot-rest planks.

Bleachers shall have mill-finished foot planks.

Bleachers shall have safety rails on both sides, compliant with Occupational Health and Safety Administration (OSHA) standards.

Bleachers shall be IBC compliant.

SESAMS Magazine and Bolt Kits The Special Effects Small Arms Marking Systems (SESAMS) components shall be purchased from Commercial entities and the commercial products have met commercial standards for production.

SESAMS M4 Adapter Kits: The M4 Adapter Kit includes the following components: M4 BOLT KITS 9mm UPPER RECIEVER KIT, M4A4, (Uses 9mm Ammo) with (2) M4A4 9mm Magazines.

SESAMS Colt 1911 .45 Cal Pistol Kit includes two (2) .45 Cal Magazine.

Marine Corps Air Station (MCAS) Beaufort Pistol Range Repair All replacement parts and ancillary equipment shall be compatible and interoperable with the existing Meggitt ATO3000 Pistol Range Target System.

Acronyms

image1.png image2.emf