M0026313T0021_Repair_Turbine.doc

Section B - Supplies or Services and Prices

Service

FFP

Repair Turbine #1 located at the main Power Plant (building 160) per the statement of work included in this solicitation.

FOB: Destination

MILSTRIP: M3200013SUFSD64

PURCHASE REQUEST NUMBER: M3200013SUFSD64

NET AMT

Section C - Descriptions and Specifications

STATEMENT OF WORK

MI-TECH PROVIDED THE GOVERNMENT WITH A STATEMENT OF WORK (SOW) FOR THE REPAIRS NEEDED TO RESTORE THIS TURBINE TO AN OPERATIONAL UNIT. THIS SOW WAS THE RESULT OF A WRITTEN REPORT REQUIRED AS A DELIVERABLE UNDER A PREVIOUS CONTRACT (M00263-13-P-0023). THIS SOLICITATION INCORPORATES THE SOW THAT MI-TECH PROVIDED IN ITS SOW, BELOW. FAR SUBPART 9.505-2(b)(1)STATES, “IF A CONTRACTOR PREPARES, OR ASSISTS IN PREPARING, A WORK STATEMENT TO BE USED IN COMPETITIVELY ACQUIRING A SYSTEM OR SERVICES OR PROVIDES MATERIAL LEADING DIRECTLY, PREDICTABLY, AND WITHOUT DELAY TO SUCH A WORK STATEMENT -- THAT CONTRACTOR MAY NOT SUPPLY THE SYSTEM OR THE SERVICE UNLESS-(i) IT IS THE SOLE SOURCE; (ii)IT HAS PARTICIPATED IN THE DEVELOPMENT AND DESIGN WORK; OR (iii) MORE THAN ONE CONTRACTOR HAS BEEN INVOLVED IN PREPARING THE WORK STATEMENT.” NONE OF THESE CONDITIONS APPLY. THEREFORE, MI-TECH IS EXCLUDED FROM COMPETITION REGARDING THIS SOLICITATION.

THIS IS A PERFORMANCE BASED ACQUISITION. THE STATEMENT OF WORK CONTAINS THE TASKS TO BE PERFORMED IN THE REPAIR OF THE TURBINE. THE GOVERNMENT EXPECTS THE TASKS OUTLINED IN SECTIONS I THROUGH VIII WILL ULTIMATELY LEAD TO A FULLY FUNCTIONAL TURBINE AND ASSOCIATED EQUIPMENT IN ACCORDANCE WITH ORIGINAL EQUIPMENT MANUFACTURER SPECIFICATIONS. ADDITIONALLY, THE GOVERNMENT EXPECTS THE CONTRACTOR TO PERFORM ALL TASKS OUTLINED IN SECTIONS I THROUGH VIII. HOWEVER, THE CONTRACTOR SHALL BE ULTIMATELY RESPONSIBLE FOR ENSURING THE TURBINE AND ALL ASSOCIATED EQUIPMENT DISCUSSED AT SECTIONS I THROUGH VIII ARE FULLY FUNCTIONAL IN ACCORDANCE WITH THEIR INTENDED FUNCTION AND ORIGINAL EQUIPMENT MANUFACTURER SPECIFICATIONS. TO THAT END, THE CONTRACTOR WILL BE ENCOURAGED TO INSTITUTE INNOVATIVE AND COST EFFECTIVE METHODS OF PERFORMING THE WORK. THIS PROJECT WILL BE MONITORED BY A GOVERNMENT TECHNICAL REPRESENTATIVE. AT THE CONCLUSION OF ALL REPAIRS THERE SHALL BE AN OPERATIONAL TEST OF THE TURBINE/GENERATOR/EXCITER PER THE STATEMENT OF WORK BELOW. UPON COMPLETION OF THE TEST, THE UNIT SHALL BE AN OPERATIONAL SYSTEM.

I. TURBINE

A. THE TURBINE CASING INTERIOR SURFACES SHALL BE HAND

CLEANED TO REMOVE THE ACCUMULATION OF RUST DEPOSITS

CAUSED FROM LEAK-BY OF THE STEAM STOP VALVES.

B. THE DIAPHRAGMS SHALL BE REMOVED AND SANDBLASTED. THE

DIAPHRAGMS ARE SEVERELY DETERIORATED IN THE AREAS WHERE

THE ADJUSTING SCREWS LAND, MAKING SECURING OF THE

DIAPHRAGMS ONCE ALIGNED DIFFICULT. THE DETERIORATED

AREAS OF THE DIAPHRAGMS IN WAY OF THE ADJUSTING SCREWS

SHALL BE BUILT UP BY WELDING AND SPOT FACED TO GIVE THE

ADJUSTING SCREWS A FLAT PLACE TO LAND, TO ENSURE

THE DIAPHRAMS STAY IN POSITION AFTER THEY ARE ALIGNED.

THE DIAPHRAGM ADJUSTING SCREWS SHALL BE REPLACED.

C. THE TURBINE ROTOR SHALL BE BLAST CLEANED USING NON

DESTRUCTIVE MEDIA TO REMOVE HEAVY ACCUMULATION OF

RUST DEPOSITS.

D. THE TURBINE ROTOR SHALL BE BALANCE CHECKED AND

CORRECTIONS PERFORMED TO DESIGN SPECIFICATIONS.

E. THE GLAND PACKING HOUSINGS SHALL BE REMOVED, BLAST

CLEANED AND REINSTALLED IN THE CASINGS.

F. THE REMAINING STEAM LABYRINTH PACKING SHALL BE HAND

CLEANED IN PLACE.

G. THE TURBINE BEARING HOUSINGS SHALL BE MANUALLY CLEANED

TO REMOVE ANY CONTAMINATION CAUSED FROM THE FAILURE OF

THE BRONZE GOVERNOR DRIVE GEAR.

H. THE FRONT BEARING HOUSING IS MISALIGNED TO THE CASING

INTERNAL FIT AND MUST BE REMOVED, THE SPIGOT FIT

CLEANED AND REALIGNED TO THE INTERNAL CASING FITS.

I. THE DAMAGED GOVERNOR DRIVE GEAR SHALL BE REPLACED AND

PROPERLY ADJUSTED FOR DESIGN BACKLASH AND TOOTH

CONTACT.

J. THE SPEED LIMITING GOVERNOR FLYWEIGHT PIVOT PIN

RETAINING SET SCREW WAS FOUND LOOSE DURING DISASSEMBLY

ALLOWING THE PIN TO RUB THE INTERNAL SURFACE OF THE

GOVERNOR HOUSING, CONTRIBUTING TO EXCESSIVE LOADING ON

THE BRONZE DRIVE GEAR. PROVIDE A NEW FLYWEIGHT PIVOT

PIN AND RETAINING SCREW(S). ENSURE PROPER FIT BETWEEN

THE PIN AND INTERNAL DIAMETER OF THE MATING COMPONENTS.

K. THE GOVERNOR BEARINGS SHALL BE REPLACED DUE TO BRONZE

CONTAMINATION.

L. THE TURBINE’S FIVE (5) PRIMARY CONTROL VALVES AND THREE

(3) EXTRACTION CONTROL VALVES STEAM SIDE SHALL BE BLAST

CLEANED TO REMOVE THE HEAVY ACCUMULATION OF RUST

DEPOSITS, REINSTALLED AND PROPERLY ADJUSTED PRIOR TO

START UP.

M. THE OIL SIDE OF THE CONTROL VALVES HAS A HEAVY

CONTAMINATION OF BRONZE PARTICLES AND SHALL BE STEAM

CLEANED IN THE INTERNAL PASSAGES.

N. THE TURBINE SHALL BE REASSEMBLED.

II. STEAM STOP GUARDING VALVE

A. THE STEAM STOP GUARDING VALVE HAS BEEN REPLACED BY

FACILITIES MAINTENANCE. THE CONTRACTOR SHALL VERIFY

THIS VALVE OPENS AND CLOSES PROPERLY. THE CONTRACTOR

SHALL ALSO REPAIR THE OLD REPLACED VALVE. THIS VALVE

SHALL BE KEPT AS A REPLACEMENT/SPARE BY THE GOVERNMENT.

B. THE OLD REPLACED VALVE SHALL BE DISASSEMBLED AND

REPAIRED TO CORRECT ANY FOUND DISCREPANCIES PREVENTING A STEAM TIGHT COMPONENT.

C. AFTER COMPLETION OF THE REPAIRS THE DISC TO SEAT

CONTACT SHALL BE VERIFIED BY THE BLUE TRANSFER METHOD.

D. THE OLD REPLACED VALVE SHALL BE HYDROSTATICALLY TESTED

TO ENSURE NO LEAKAGE AFTER COMPLETION OF ALL REPAIRS AND RETURNED TO THE GOVERNMENT.

III. GENERATOR

A. THE EXCITER END JOURNAL BEARING’S BABBITT WAS NOTED TO

BE SEPARATED FROM THE BEARING SHELL AND SHALL BE

REFURBISHED TO REESTABLISH A COHESIVE BOND.

B. THE REFURBISHED BEARING SHALL THEN BE BLUE CONTACT

VERIFIED AND FITTED FOR SATISFACTORY CONTACT AND

CLEARANCE IN ACCORDANCE WITH INDUSTRY STANDARDS.

C. THE BEARING ALIGNMENT OF BOTH ELECTRICAL END BEARINGS

SHALL BE REALIGNED AFTER COMPLETION OF THE BEARING

REPAIRS.

D. THE TWO (2) EACH BEARING HOUSINGS SHALL BE MANUALLY

CLEANED TO REMOVE THE BRONZE CONTAMINATION.

E. THE GENERATOR STATOR WINDINGS ARE DIRTY AND SHALL BE

CLEANED. REMOVE THE ROTOR AND CLEAN THE STATOR IN

PLACE. REMOVE BROKEN PIECES OF INSULATION ON THE

INTERNAL STATOR HOUSING. PERFORM ELECTRICAL TEST ON

BOTH THE STATOR AND ROTOR TO VERIFY THEY ARE

OPERATIONAL AND IAW OEM SPECIFICATIONS. THE ROTOR

SHALL ALSO BE CLEANED, SLIP RINGS MACHINED, AND THE

ROTOR BALANCED PRIOR TO REINSTALLATION IN THE STATOR.

PRIOR TO INSTALLATION OF THE ROTOR AND PROVIDING ALL

ELECTRICAL TEST MEET OEM SPECIFICATIONS, REPAIR IN

PLACE THE AREAS WHERE BROKEN INSULATION WAS REMOVED.

F. THE BRUSH RIGGING AND CARBON BRUSH SPRINGS ARE HEAVILY

CORRODED AND SHALL BE BLAST CLEANED AND THE ELECTRICAL

CONNECTION FASTENERS SHALL BE REPLACED. AFTER

COMPLETION OF REPAIRS, THE BRUSHES SHALL BE FITTED TO

THE MACHINED SLIP RINGS AND THE SPRING TENSION

ADJUSTED PER THE MAINTENANCE AND REPAIR MANUAL TO OEM

SPECIFICATIONS.

G. THE GENERATOR ROTOR SHALL FIRST BE ALIGNED TO THE

TURBINE ROTOR AFTER COMPLETION OF THE BEARING ALIGNMENT

CORRECTIONS.

H. THE GENERATOR ROTOR TO STATOR AIR GAPS SHALL BE

MEASURED AND THE STATOR ALIGNED TO DESIGN/OEM

SPECIFICATIONS AFTER COMPLETION OF THE ABOVE

WORKSCOPES.

IV. EXCITER

A. THE TWO (2) EACH EXCITER JOURNAL BEARING SHELLS ARE

DISTORTED AND UNDERSIZED IN THE VERTICAL DIRECTION AND

SHALL BE REPLACED AND FITTED FOR DESIGN CLEARANCES AND

CONTACT.

B. THE TWO (2) EACH BEARING HOUSINGS SHALL BE MANUALLY

CLEANED TO REMOVE ALL BRONZE CONTAMINATION.

C. THE STATOR AND ROTOR SHALL BE CLEANED AND ELECTRICALLY

TESTED TO VERIFY THE UNITS MEET ELECTRICAL DESIGN

SPECIFICATIONS.

D. THE ROTOR SHALL BE REMOVED FROM THE STATOR FOR

CLEANING, MACHINING AND BALANCING. MACHINE THE

COMMUTATOR TO MEET OEM SURFACE FINISH REQUIREMENTS.

E. THE BRUSH RIGGING AND CARBON BRUSH SPRINGS ARE HEAVILY

CORRODED AND SHALL BE BLAST CLEANED AND THE ELECTRICAL

CONNECTION FASTENERS SHALL BE REPLACED.

F. AFTER COMPLETION OF THE REPAIRS, THE BRUSHES SHALL BE

FITTED TO THE MACHINED COMMUTATOR PER OEM

SECIFICATIONS.

G. THE EXCITER SHALL BE REALIGNED TO THE GENERATOR AFTER

COMPLETION OF THE GENERATOR TO TURBINE ALIGNMENTS.

H. THE STATOR AIR GAPS SHALL BE MEASURED AND CORRECTED

AFTER THE ALIGNMENT OF THE EXCITER ROTOR TO THE

GENERATOR.

V. STEAM DRIVEN LUBE OIL PUMP

A. THE TURBINE WHEEL BLADING IS DETERIORATED AND ERODED

AND THE SHAFT FIT HAS .010″ CLEARANCE. THIS FIT AREA

SHOULD BE AN INTERFERENCE FIT FOR PROPER OPERATION OF

THE UNIT. THE WHEEL (DISK ASSEMBLY, PC. 5) SHALL BE

REPLACED OR REFURBISHED IF A REPLACEMENT IS NOT

AVAILABLE.

B. THE STEAM INLET NOZZLE IS SEVERELY ERODED AND HAS

REDUCED THE WALL THICKNESS OF THE TURBINE CASING AND

EVENTUALLY WILL LEAD TO AN UNSAFE CONDITION. THE STEAM

END WITH INTEGRAL NOZZLE (PC. 2) SHALL BE REPAIRED IF A

REPLACEMENT IS NOT AVAILABLE.

C. PROVIDE NEW CARBON PACKING RINGS (PC 8). PREPARE THE

RINGS FOR INSTALLATION BY SQUARING THE SEGMENT ENDS

BEFORE INSTALLATION.

D. THE SHAFT (PC. 6) IS BENT .006″ IN THE CENTER AND SHALL

BE REPLACED.

E. THE LABYRINTH RING (PC. 9) IS WORN BEYOND REUSE AND

SHALL BE REPLACED.

F. THE UPPER DISTANCE PIECE (PC. 15) IS DAMAGED ON THE

ENDS AND SHALL BE REPLACED TO ENSURE PROPER STACKING OF

THE ROTATING ASSEMBLY.

G. THE LOWER DISTANCE PIECE (PC. 37) IS DAMAGED ON THE

ENDS AND HAS A ROUGH FINISH IN THE SEALING AREA, AND

SHALL BE REPLACED.

H. THE SHIMS (PC. 16) ARE DAMAGED AND SHALL BE REPLACED.

I. THE SPECIAL WASHER (PC. 18) FOR THE BUCKET WHEEL IS

DAMAGED AND SHALL BE REPLACED.

J. THE OIL SEAL (PC. 22) IS WORN AND SHALL BE REPLACED.

K. THE BALL BEARING (PC. 23) IS WORN AND SHALL BE

REPLACED. THE BALL BEARING HOUSING WAS PREVIOUSLY

DAMAGED AND WELD REPAIRED, THEN HAND WORKED CAUSING

UNEVEN SEATING OF THE BEARING AND SEAL HOUSING. THE FIT

AREA SHALL BE MACHINED TO FACILITATE AN INTERFERENCE

FIT SLEEVE TO RESTORE DESIGN FITS.

L. THE CHECK VALVE PISTON (PC. 11) IS SEVERELY PITTED IN

THE SEATING AREA AND SHALL BE SKIM CUT TO ENSURE PROPER

SEATING.

M. PROVIDE A NEW AUTOMATIC CONTROL VALVE IF AVAILABLE.

REBUILD THE EXISTING VALVE IF A NEW ONE CANNOT BE

PROCURED.

N. THE STEAM SEAT TO DISC HAS MINOR IMPERFECTIONS AND

SHALL BE MACHINED/LAPPED.

O. THE HYDRAULIC CONTROL NEOPRENE DIAPHRAGM IS BRITTLE AND

DETERIORATED AND SHALL BE REPLACED.

P. AFTER COMPLETION OF THE REPAIRS THE VALVE SHALL BE

ADJUSTED FOR AUTOMATIC OPERATION.

VI. TRIP THROTTLE VALVE

A. THE VALVE DISC AND SEATING FITS HAVE MINOR INDENTATIONS

IN THE CONTACT SURFACE AND SHALL BE MACHINED AND LAPPED

TO REMOVE THE IMPERFECTIONS.

B. THE DISC TO SEAT CONTACT SHALL THEN BE VERIFIED BY THE

BLUE TRANSFER METHOD.

C. THE VALVE SHALL BE REASSEMBLED AFTER COMPLETION OF ALL

REPAIRS AND HYDROSTATICALLY TESTED TO VERIFY NO

LEAKAGE.

VII. LUBE OIL SYSTEM

A. THE LUBE OIL TANK IS CONTAMINATED WITH WATER, SLUDGE AND

BRONZE PARTICLES AND SHALL BE DRAINED AND MANUALLY

CLEANED.

B. SECURE THE SUMP TANK TOP ACCESS COVER. REPLACE MISSING

BOLTS AND REPAIR STRIPPED THREADED BOLT HOLES.

ELIMINATE ENTRANCE OF ALL POSSIBLE CONTAMINANTS.

C. PIPING PENETRATIONS ON THE SUMP TOP SHALL BE SEALED

TO PREVENT CONTAMINATION OF THE LUBE OIL.

D. PROVIDE NEW COVERS (7 EACH). COVERS SHALL BE

MANUFACTURED WITH O-RING SEALS TO PREVENT WATER AND

DEBRIS FROM ENTERING THE TANK.

E. THE LUBE OIL DUPLEX STRAINER PIPING SHALL BE TAPPED FOR

GAGE LINES ON THE INLET AND OUTLET PIPING, AND CONNECTED

TO A DIFFERENTIAL PRESSURE GAGE TO ALERT THE OPERATOR OF

DIRTY OR CLOGGED STRAINER BASKETS.

F. THE ACCESSIBLE LUBE OIL PIPING SHALL BE REMOVED AND

CHEMICALLY CLEANED TO REMOVE ALL CONTAMINATION.

G. THE LUBE OIL COOLER SHALL BE DISASSEMBLED AND CLEANED TO

REMOVE ANY CONTAMINATION AND THE TUBES CLEANED TO ENSURE

PROPER COOLING OF THE LUBE OIL.

H. THE PIPING SHALL BE REINSTALLED AND TEMPORARY JUMPER

LINES INSTALLED FOR THE INITIAL HOT OIL FLUSH UNTIL THE

EXTERNAL FILTER ELEMENTS INDICATE NO CONTAMINATION.

I. THE SYSTEM SHALL BE FLUSHED WITH AN EXTERNAL HIGH

VOLUME PUMP, HEATER AND FILTER SYSTEM.

J. THE PIPING SHALL BE RECONNECTED TO THE BEARINGS AND

VARIOUS OTHER OIL OPERATED COMPONENTS AFTER WHICH THE

HOT OIL FLUSH SHALL CONTINUE UNTIL THE SYSTEM IS

DETERMINED TO BE FREE OF CONTAMINANTS.

K. AFTER COMPLETION OF ALL FLUSHING, THE OIL TANK SHALL BE

DRAINED, CLEANED AND THE TANK INTERNAL SURFACE

INSPECTED TO VERIFY THERE ARE NO VISIBLE CONTAMINANTS.

L. THE SYSTEM SHALL BE FILLED WITH A NEW CHARGE OF TURBINE

OIL PRIOR TO OPERATIONAL TESTING.

VIII. OPERATIONAL TEST

PERFORM A COMPLETE AND THOROUGH OPERATIONAL TEST OF THE

TURBINE PER INDUSTRY STANDARDS. OPERATIONAL TEST SHALL

CONSIST OF STARTING UP THE TURBINE. WARM THE TURBINE

UNTIL PRESSURES AND TEMPERATURES STABILIZE. CHECK THE

TRIPS, SAFETY FEATURES AND ALARMS. GRADUALLY LOAD THE

TURBINE UNTIL MAXIMUM ELECTRICAL LOAD IS APPLIED.

TURBINE SHALL BE RAN UNDER MAXIMUM LOAD FOR A MINIMUM OF

FOUR (4) HOURS. DURING THIS OPERATIONAL TEST, OPERATING

PRESSURES AND TEMPERATURES SHALL BE MONITORED AS WELL AS

ANY ABNORMAL VIBRATION. CHECK THE EXTRACTION FEATURES

FOR PROPER OPERATION. THE COMPLETE OPERATIONAL TESTING

OF THE REPAIRED TURBINE SHALL BE OBSERVED BY A

GOVERNMENT TECHNICAL REPRESENTATIVE. THIS TEST SHALL

PROVIDE FINAL VERIFICATION TO THE GOVERNMENT TECHNICAL

REPRESENTATIVE THAT THE TURBINE AND ALL ASSOCIATED

EQUIPMENT FUNCTION AS INTENDED AND IN ACCORDANCE WITH

ORIGINAL EQUIPMENT MANUFACTURER SPECIFICATIONS. ALL

REQUIREMENTS OF THIS CONTRACT WILL BE CONSIDERED

SATISFIED WHEN THE GOVERNMENT TECHNICAL REPRESETATIVE

CONFIRMS TO THE CONTRACTING OFFICER THAT THE TURBINE

AND ALL ASSOCIATED EQUIPMENT FUNCTION AS INTENDED AND IN

ACCORDANCE WITH ORIGINAL EQUIPMENT MANUFACTURER

SPECIFICATIONS.

Turbine Fully Operational – Performance Requirements Summary (PRS)

· Section VIII

· Operational test will be verified by the Government technical representative

COMBINED SYNOPSIS/SOLICITATION

MI-TECH PROVIDED THE GOVERNMENT WITH A STATEMENT OF WORK (SOW) FOR THE REPAIRS NEEDED TO RESTORE THIS TURBINE TO AN OPERATIONAL UNIT. THIS SOW WAS THE RESULT OF A WRITTEN REPORT REQUIRED AS A DELIVERABLE UNDER A PREVIOUS CONTRACT (M00263-13-P-0023). THIS SOLICITATION INCORPORATES THE SOW THAT MI-TECH PROVIDED IN ITS SOW BELOW. FAR SUBPART 9.505-2(B)(1)STATES, “IF A CONTRACTOR PREPARES, OR ASSISTS IN PREPARING, A WORK STATEMENT TO BE USED IN COMPETITIVELY ACQUIRING A SYSTEM OR SERVICES OR PROVIDES MATERIAL LEADING DIRECTLY, PREDICTABLY, AND WITHOUT DELAY TO SUCH A WORK STATEMENT -- THAT CONTRACTOR MAY NOT SUPPLY THE SYSTEM OR THE SERVICE UNLESS- (i) IT IS THE SOLE SOURCE; (ii)IT HAS PARTICIPATED IN THE DEVELOPMENT AND DESIGN WORK; OR (iii) MORE THAN ONE CONTRACTOR HAS BEEN INVOLVED IN PREPARING THE WORK STATEMENT.” NONE OF THESE CONDITIONS APPLY. THEREFORE, MI-TECH IS EXCLUDED FROM COMPETITION REGARDING THIS SOLICITATION.

THIS IS A COMBINED SYNOPSIS/SOLICITATION FOR A COMMERCIAL SERVICE UTILIZING FAR PART 12 ACQUISITION OF COMMERCIAL ITEMS, PART 13 SIMPLIFIED ACQUISTION PROCEDURES AND FAR SUBPART 13.5 TEST PROGRAM FOR CERTAIN COMMERCIAL ITEMS, AS SUPPLEMENTED WITH ADDITIONAL INFORMATION INCLUDED IN THIS NOTICE. THIS SOLICITATION (M00263-13-T-0021) IS BEING ISSUED AS A REQUEST FOR QUOTE (RFQ). THIS ACTION IS BEING SOLICITED AS A 100% TOTAL SMALL BUSINESS SET ASIDE. THE NAICS (NORTH AMERICAN INDUSTRIAL CLASSIFICATION) CODE IS 333611 WITH A SIZE STANDARD OF 1000 EMPLOYEES. THIS REQUIREMENT IS FOR SERVICES TO REPAIR TURBINE # 1 AT BUILDING 160 (POWER PLANT), ABOARD MARINE CORPS RECRUIT DEPOT, PARRIS ISLAND, SC. THE INTENT OF THE GOVERNMENT IS TO AWARD A FIRM FIXED PRICE (FFP) CONTRACT FROM THIS SOLICITATION.

ALL APPLICABLE CLAUSES AND PROVISIONS ARE INCLUDED IN THIS SOLICITATION. THE FULL TEXT OF CLAUSES INCLUDED BY REFERENCE CAN BE FOUND AT WWW.ACQUISITION.GOV/FAR/. QUOTERS ARE REQUIRED TO PROVIDE THEIR CONTRACTOR’S DUNS NUMBER AND COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE WITH THEIR QUOTE. THE CAGE CODE ENTERED SHALL BE FOR THAT NAME AND ADDRESS PROVIDED BY THE CONTRACTOR. QUOTERS ARE REQUIRED TO BE REGISTERED AND CURRENT IN SYSTEM FOR AWARD MANAGEMENT (SAM) AND WIDE AREA WORK FLOW (WAWF) DATABASES. FOR SAM ASSISTANCE, VISIT THEIR WEBSITE AT HTTPS://WWW.SAM.GOV OR CONTACT CUSTOMER SERVICE AT 1-866-606-8220. FOR ASSISTANCE WITH WAWF, VISIT THEIR WEBSITE AT HTTPS://WAWF.EB.MIL/ OR CONTACT CUSTOMER SERVICE AT 1-866-618-5988.

QUOTERS SHALL BE RESPONSIBLE FOR SUBMITTING ALL REQUIREMENTS PER THE “ADDITIONAL INSTRUCTIONS” INCLUDED IN SECTION L (INSTRUCTIONS, CONDITIONS AND NOTICE TO BIDDERS) OF THIS SOLICITATION.

QUOTES SHALL BE EVALUATED ON THE CRITERIA INCLUDED IN CLAUSE 52.212-2 EVALUATION-COMMERCIAL ITEMS AS INCLUDED IN SECTION M (EVALUATION FACTORS FOR AWARD) OF THIS SOLICITATION.

ALL RESPONSIBLE SOURCES MAY SUBMIT A RESPONSE WHICH, IF TIMELY RECEIVED, WILL BE CONSIDERED BY THE CONTRACTING OFFICE. THE CLOSING DATE AND TIME FOR THIS SOLICITATION IS 30 August 2013 AT 12:00 P.M. EASTERN STANDARD TIME (EST). QUOTERS ARE RESPONSIBLE FOR ENSURING THEIR SUBMITTED QUOTE HAS BEEN RECEIVED AND THAT IT IS LEGIBLE.

Section E - Inspection and Acceptance

INSPECTION AND ACCEPTANCE TERMS

Supplies/services will be inspected/accepted at:

Section F - Deliveries or Performance

DELIVERY INFORMATION

31-DEC-2013

MIKE KUHN

BLDG 160

PARRIS ISLAND SC 29905

843-770-0698

FOB: Destination M00263

Section G - Contract Administration Data

Section H - Special Contract Requirements

REPORTING LABOR HOURS

The contractor shall report ALL contractor labor hours (including subcontractor labor hours) required for performance of services provided under this contract for the REGIONAL CONTRACTING OFFICE, MCRD/ERR, PARRIS ISLAND, SC 29905 via a secure data collection site. The contractor is required to completely fill in all required data fields using the following web address https://doncmra.nmci.navy.mil .

“The contractor shall report ALL contractor labor hours (including subcontractor labor hours) required for performance of services provided under a contract that is issued for solicitation [M00263-13-T-0021 Repairing Turbine # 1 located at building 160 Power Plant, aboard MCRD Parris Island, SC] via a secure data collection site. The contractor is required to completely fill in all required data fields using the following web address https://doncmra.nmci.navy.mil .

Reporting inputs will be for the labor executed during the period of performance during each Government fiscal year (FY), which runs October 1 through September 30. While inputs may be reported any time during the FY, all data shall be reported no later than October 31 of each calendar year. Contractors may direct questions to the help desk, linked at https://doncmra.nmci.navy.mil.”

WAGE DETERMINATION

U. S. Department of Labor Wage Determination Number 2005-2473, Revision number 15, dated 19 Jun 2013 is hereby incorporated into this order. The Wage Determination can be found at:

www.wdol.gov Section I - Contract Clauses

CLAUSES INCORPORATED BY REFERENCE

CLAUSES INCORPORATED BY FULL TEXT

52.212-1 INSTRUCTIONS TO OFFERORS--COMMERCIAL ITEMS (FEB 2012)

(a) North American Industry Classification System (NAICS) code and small business size standard. The NAICS code and small business size standard for this acquisition appear in Block 10 of the solicitation cover sheet (SF 1449). However, the small business size standard for a concern which submits an offer in its own name, but which proposes to furnish an item which it did not itself manufacture, is 500 employees.

(b) Submission of offers. Submit signed and dated offers to the office specified in this solicitation at or before the exact time specified in this solicitation. Offers may be submitted on the SF 1449, letterhead stationery, or as otherwise specified in the solicitation. As a minimum, offers must show--

(1) The solicitation number;

(2) The time specified in the solicitation for receipt of offers;

(3) The name, address, and telephone number of the offeror;

(4) A technical description of the items being offered in sufficient detail to evaluate compliance with the requirements in the solicitation. This may include product literature, or other documents, if necessary;

(5) Terms of any express warranty;

(6) Price and any discount terms;

(7) "Remit to" address, if different than mailing address;

(8) A completed copy of the representations and certifications at FAR 52.212-3 (see FAR 52.212-3(b) for those representations and certifications that the offeror shall complete electronically);

(9) Acknowledgment of Solicitation Amendments;

(10) Past performance information, when included as an evaluation factor, to include recent and relevant contracts for the same or similar items and other references (including contract numbers, points of contact with telephone numbers and other relevant information); and

(11) If the offer is not submitted on the SF 1449, include a statement specifying the extent of agreement with all terms, conditions, and provisions included in the solicitation. Offers that fail to furnish required representations or information, or reject the terms and conditions of the solicitation may be excluded from consideration.

(c) Period for acceptance of offers. The offeror agrees to hold the prices in its offer firm for 30 calendar days from the date specified for receipt of offers, unless another time period is specified in an addendum to the solicitation.

(d) Product samples. When required by the solicitation, product samples shall be submitted at or prior to the time specified for receipt of offers. Unless otherwise specified in this solicitation, these samples shall be submitted at no expense to the Government, and returned at the sender's request and expense, unless they are destroyed during preaward testing.

(e) Multiple offers. Offerors are encouraged to submit multiple offers presenting alternative terms and conditions or commercial items for satisfying the requirements of this solicitation. Each offer submitted will be evaluated separately.

(f) Late submissions, modifications, revisions, and withdrawals of offers:

(1) Offerors are responsible for submitting offers, and any modifications, revisions, or withdrawals, so as to reach the Government office designated in the solicitation by the time specified in the solicitation. If no time is specified in the solicitation, the time for receipt is 4:30 p.m., local time, for the designated Government office on the date that offers or revisions are due.

(2)(i) Any offer, modification, revision, or withdrawal of an offer received at the Government office designated in the solicitation after the exact time specified for receipt of offers is “late” and will not be considered unless it is received before award is made, the Contracting Officer determines that accepting the late offer would not unduly delay the acquisition; and--

(A) If it was transmitted through an electronic commerce method authorized by the solicitation, it was received at the initial point of entry to the Government infrastructure not later than 5:00 p.m. one working day prior to the date specified for receipt of offers; or

(B) There is acceptable evidence to establish that it was received at the Government installation designated for receipt of offers and was under the Government's control prior to the time set for receipt of offers; or

(C) If this solicitation is a request for proposals, it was the only proposal received.

(ii) However, a late modification of an otherwise successful offer, that makes its terms more favorable to the Government, will be considered at any time it is received and may be accepted.

(3) Acceptable evidence to establish the time of receipt at the Government installation includes the time/date stamp of that installation on the offer wrapper, other documentary evidence of receipt maintained by the installation, or oral testimony or statements of Government personnel.

(4) If an emergency or unanticipated event interrupts normal Government processes so that offers cannot be received at the Government office designated for receipt of offers by the exact time specified in the solicitation, and urgent Government requirements preclude amendment of the solicitation or other notice of an extension of the closing date, the time specified for receipt of offers will be deemed to be extended to the same time of day specified in the solicitation on the first work day on which normal Government processes resume.

(5) Offers may be withdrawn by written notice received at any time before the exact time set for receipt of offers. Oral offers in response to oral solicitations may be withdrawn orally. If the solicitation authorizes facsimile offers, offers may be withdrawn via facsimile received at any time before the exact time set for receipt of offers, subject to the conditions specified in the solicitation concerning facsimile offers. An offer may be withdrawn in person by an offeror or its authorized representative if, before the exact time set for receipt of offers, the identity of the person requesting withdrawal is established and the person signs a receipt for the offer.

(g) Contract award (not applicable to Invitation for Bids). The Government intends to evaluate offers and award a contract without discussions with offerors. Therefore, the offeror's initial offer should contain the offeror's best terms from a price and technical standpoint. However, the Government reserves the right to conduct discussions if later determined by the Contracting Officer to be necessary. The Government may reject any or all offers if such action is in the public interest; accept other than the lowest offer; and waive informalities and minor irregularities in offers received.

(h) Multiple awards. The Government may accept any item or group of items of an offer, unless the offeror qualifies the offer by specific limitations. Unless otherwise provided in the Schedule, offers may not be submitted for quantities less than those specified. The Government reserves the right to make an award on any item for a quantity less than the quantity offered, at the unit prices offered, unless the offeror specifies otherwise in the offer.

(i) Availability of requirements documents cited in the solicitation. (1)(i) The GSA Index of Federal Specifications, Standards and Commercial Item Descriptions, FPMR Part 101-29, and copies of specifications, standards, and commercial item descriptions cited in this solicitation may be obtained for a fee by submitting a request to--GSA Federal Supply Service Specifications Section, Suite 8100, 470 East L'Enfant Plaza, SW, Washington, DC

20407, Telephone (202) 619-8925, Facsimile (202) 619-8978.

(ii) If the General Services Administration, Department of Agriculture, or Department of Veterans Affairs issued this solicitation, a single copy of specifications, standards, and commercial item descriptions cited in this solicitation may be obtained free of charge by submitting a request to the addressee in paragraph (i)(1)(i) of this provision. Additional copies will be issued for a fee.

(2) Most unclassified Defense specifications and standards may be downloaded from the following ASSIST websites:

(i) ASSIST (http://assist.daps.dla.mil).

(ii) Quick Search (http://assist.daps.dla.mil/quicksearch).

(iii) ASSISTdocs.com (http://assistdocs.com).

(3) Documents not available from ASSIST may be ordered from the Department of Defense Single Stock Point (DoDSSP) by--

(i) Using the ASSIST Shopping Wizard (http://assist.daps.dla.mil/wizard);

(ii) Phoning the DoDSSP Customer Service Desk (215) 697-2179, Mon-Fri, 0730 to 1600 EST; or

(iii) Ordering from DoDSSP, Building 4, Section D, 700 Robbins Avenue, Philadelphia, PA 19111-5094, Telephone (215) 697-2667/2179, Facsimile (215) 697-1462.

(4) Nongovernment (voluntary) standards must be obtained from the organization responsible for their preparation, publication, or maintenance.

(j) Data Universal Numbering System (DUNS) Number. (Applies to all offers exceeding $3,000, and offers of $3,000 or less if the solicitation requires the Contractor to be registered in the Central Contractor Registration (CCR) database. The offeror shall enter, in the block with its name and address on the cover page of its offer, the annotation “DUNS” or “DUNS +4” followed by the DUNS or DUNS +4 number that identifies the offeror's name and address. The DUNS +4 is the DUNS number plus a 4-character suffix that may be assigned at the discretion of the offeror to establish additional CCR records for identifying alternative Electronic Funds Transfer (EFT) accounts (see FAR Subpart 32.11) for the same concern. If the offeror does not have a DUNS number, it should contact Dun and Bradstreet directly to obtain one. An offeror within the United States may contact Dun and Bradstreet by calling 1-866-705-5711 or via the internet at http://fedgov.dnb.com/webform. An offeror located outside the United States must contact the local Dun and Bradstreet office for a DUNS number. The offeror should indicate that it is an offeror for a Government contract when contacting the local Dun and Bradstreet office.

(k) Central Contractor Registration. Unless exempted by an addendum to this solicitation, by submission of an offer, the offeror acknowledges the requirement that a prospective awardee shall be registered in the CCR database prior to award, during performance and through final payment of any contract resulting from this solicitation. If the Offeror does not become registered in the CCR database in the time prescribed by the Contracting Officer, the Contracting Officer will proceed to award to the next otherwise successful registered Offeror. Offerors may obtain information on registration and annual confirmation requirements via the CCR database accessed through https://www.acquisition.gov or by calling 1-888-227-2423 or 269-961-5757.

(l) Debriefing. If a post-award debriefing is given to requesting offerors, the Government shall disclose the following information, if applicable:

(1) The agency's evaluation of the significant weak or deficient factors in the debriefed offeror's offer.

(2) The overall evaluated cost or price and technical rating of the successful and the debriefed offeror and past performance information on the debriefed offeror.

(3) The overall ranking of all offerors, when any ranking was developed by the agency during source selection.

(4) A summary of the rationale for award;

(5) For acquisitions of commercial items, the make and model of the item to be delivered by the successful offeror.

(6) Reasonable responses to relevant questions posed by the debriefed offeror as to whether source-selection procedures set forth in the solicitation, applicable regulations, and other applicable authorities were followed by the agency.

(End of provision)

52.212-3 OFFEROR REPRESENTATIONS AND CERTIFICATIONS--COMMERCIAL ITEMS (DEC 2012)

An offeror shall complete only paragraph (b) of this provision if the offeror has completed the annual representations and certifications electronically via https://www.acquisition.gov. If an offeror has not completed the annual representations and certifications electronically at the ORCA website, the offeror shall complete only paragraphs (c) through (o) of this provision.

(a) Definitions. As used in this provision --

“Economically disadvantaged women-owned small business (EDWOSB) Concern” means a small business concern that is at least 51 percent directly and unconditionally owned by, and the management and daily business operations of which are controlled by, one or more women who are citizens of the United States and who are economically disadvantaged in accordance with 13 CFR part 127. It automatically qualifies as a women-owned small business eligible under the WOSB Program.

"Forced or indentured child labor" means all work or service-

(1) Exacted from any person under the age of 18 under the menace of any penalty for its nonperformance and for which the worker does not offer himself voluntarily; or

(2) Performed by any person under the age of 18 pursuant to a contract the enforcement of which can be accomplished by process or penalties.

Inverted domestic corporation, as used in this section, means a foreign incorporated entity which is treated as an inverted domestic corporation under 6 U.S.C. 395(b), i.e., a corporation that used to be incorporated in the United States, or used to be a partnership in the United States, but now is incorporated in a foreign country, or is a subsidiary whose parent corporation is incorporated in a foreign country, that meets the criteria specified in 6 U.S.C. 395(b), applied in accordance with the rules and definitions of 6 U.S.C. 395(c). An inverted domestic corporation as herein defined does not meet the definition of an inverted domestic corporation as defined by the Internal Revenue Code at 26 U.S.C. 7874.

Manufactured end product means any end product in Federal Supply Classes (FSC) 1000-9999, except--

(1) FSC 5510, Lumber and Related Basic Wood Materials;

(2) Federal Supply Group (FSG) 87, Agricultural Supplies;

(3) FSG 88, Live Animals;

(4) FSG 89, Food and Related Consumables;

(5) FSC 9410, Crude Grades of Plant Materials;

(6) FSC 9430, Miscellaneous Crude Animal Products, Inedible;

(7) FSC 9440, Miscellaneous Crude Agricultural and Forestry Products;

(8) FSC 9610, Ores;

(9) FSC 9620, Minerals, Natural and Synthetic; and

(10) FSC 9630, Additive Metal Materials.

Place of manufacture means the place where an end product is assembled out of components, or otherwise made or processed from raw materials into the finished product that is to be provided to the Government. If a product is disassembled and reassembled, the place of reassembly is not the place of manufacture.

Restricted business operations means business operations in Sudan that include power production activities, mineral extraction activities, oil-related activities, or the production of military equipment, as those terms are defined in the Sudan Accountability and Divestment Act of 2007 (Pub. L. 110-174). Restricted business operations do not include business operations that the person (as that term is defined in Section 2 of the Sudan Accountability and Divestment Act of 2007) conducting the business can demonstrate--

(1) Are conducted under contract directly and exclusively with the regional government of southern Sudan;

(2) Are conducted pursuant to specific authorization from the Office of Foreign Assets Control in the Department of the Treasury, or are expressly exempted under Federal law from the requirement to be conducted under such authorization;

(3) Consist of providing goods or services to marginalized populations of Sudan;

(4) Consist of providing goods or services to an internationally recognized peacekeeping force or humanitarian organization;

(5) Consist of providing goods or services that are used only to promote health or education; or

(6) Have been voluntarily suspended.

Sensitive technology--

(1) Means hardware, software, telecommunications equipment, or any other technology that is to be used specifically--

(i) To restrict the free flow of unbiased information in Iran; or

(ii) To disrupt, monitor, or otherwise restrict speech of the people of Iran; and

(2) Does not include information or informational materials the export of which the President does not have the authority to regulate or prohibit pursuant to section 203(b)(3) of the International Emergency Economic Powers Act (50 U.S.C. 1702(b)(3)).

Service-disabled veteran-owned small business concern--

(1) Means a small business concern--

(i) Not less than 51 percent of which is owned by one or more service-disabled veterans or, in the case of any publicly owned business, not less than 51 percent of the stock of which is owned by one or more service-disabled veterans; and

(ii) The management and daily business operations of which are controlled by one or more service-disabled veterans or, in the case of a service-disabled veteran with permanent and severe disability, the spouse or permanent caregiver of such veteran.

(2) Service-disabled veteran means a veteran, as defined in 38 U.S.C. 101(2), with a disability that is service-connected, as defined in 38 U.S.C. 101(16).

"Small business concern" means a concern, including its affiliates, that is independently owned and operated, not dominant in the field of operation in which it is bidding on Government contracts, and qualified as a small business under the criteria in 13 CFR Part 121 and size standards in this solicitation.

Subsidiary means an entity in which more than 50 percent of the entity is owned--

(1) Directly by a parent corporation; or

(2) Through another subsidiary of a parent corporation.

Veteran-owned small business concern means a small business concern--

(1) Not less than 51 percent of which is owned by one or more veterans (as defined at 38 U.S.C. 101(2)) or, in the case of any publicly owned business, not less than 51 percent of the stock of which is owned by one or more veterans; and

(2) The management and daily business operations of which are controlled by one or more veterans.

"Women-owned business concern" means a concern which is at least 51 percent owned by one or more women; or in the case of any publicly owned business, at least 51 percent of the stock of which is owned by one or more women; and whose management and daily business operations are controlled by one or more women.

"Women-owned small business concern" means a small business concern--

(1) That is at least 51 percent owned by one or more women or, in the case of any publicly owned business, at least 51 percent of its stock is owned by one or more women; or

(2) Whose management and daily business operations are controlled by one or more women.

Women-owned small business (WOSB) concern eligible under the WOSB Program (in accordance with 13 CFR part 127)”, means a small business concern that is at least 51 percent directly and unconditionally owned by, and the management and daily business operations of which are controlled by, one or more women who are citizens of the United States.

(b) (1) Annual Representations and Certifications. Any changes provided by the offeror in paragraph (b)(2) of this provision do not automatically change the representations and certifications posted electronically on the Online Representations and Certifications Application (ORCA) website.

(2) The offeror has completed the annual representations and certifications electronically via the ORCA website accessed through https://www.acquisition.gov. After reviewing the ORCA database information, the offeror verifies by submission of this offer that the representations and certifications currently posted electronically at FAR 52.212-3, Offeror Representations and Certifications--Commercial Items, have been entered or updated in the last 12 months, are current, accurate, complete, and applicable to this solicitation (including the business size standard applicable to the NAICS code referenced for this solicitation), as of the date of this offer and are incorporated in this offer by reference (see FAR 4.1201), except for paragraphs ----------.

[Offeror to identify the applicable paragraphs at (c) through (o) of this provision that the offeror has completed for the purposes of this solicitation only, if any.) These amended representation(s) and/or certification(s) are also incorporated in this offer and are current, accurate, and complete as of the date of this offer. Any changes provided by the offeror are applicable to this solicitation only, and do not result in an update to the representations and certifications posted electronically on ORCA.]

(c) Offerors must complete the following representations when the resulting contract will be performed in the United States or its outlying areas. Check all that apply.

(1) Small business concern. The offeror represents as part of its offer that it ( ) is, ( ) is not a small business concern.

(2) Veteran-owned small business concern. (Complete only if the offeror represented itself as a small business concern in paragraph (c)(1) of this provision.) The offeror represents as part of its offer that it ( ) is, ( ) is not a veteran-owned small business concern.

(3) Service-disabled veteran-owned small business concern. (Complete only if the offeror represented itself as a veteran-owned small business concern in paragraph (c)(2) of this provision.) The offeror represents as part of its offer that it ( ) is, ( ) is not a service-disabled veteran-owned small business concern.

(4) Small disadvantaged business concern. (Complete only if the offeror represented itself as a small business concern in paragraph (c)(1) of this provision.) The offeror represents, for general statistical purposes, that it ( ) is, ( ) is not a small disadvantaged business concern as defined in 13 CFR 124.1002.

(5) Women-owned small business concern. (Complete only if the offeror represented itself as a small business concern in paragraph (c)(1) of this provision.) The offeror represents that it ( ) is, ( ) is not a women-owned small business concern.

Note to paragraphs (c)(8) and (9): Complete paragraphs (c)(8) and (c)(9) only if this solicitation is expected to exceed the simplified acquisition threshold.

(6) WOSB concern eligible under the WOSB Program. [Complete only if the offeror represented itself as a women-owned small business concern in paragraph (c)(5) of this provision.] The offeror represents that--

(i) It [ ] is, [ ] is not a WOSB concern eligible under the WOSB Program, has provided all the required documents to the WOSB Repository, and no change in circumstances or adverse decisions have been issued that affects its eligibility; and

(ii) It [ballot] is, [ballot] is not a joint venture that complies with the requirements of 13 CFR part 127, and the representation in paragraph (c)(6)(i) of this provision is accurate for each WOSB concern eligible under the WOSB Program participating in the joint venture. [The offeror shall enter the name or names of the WOSB concern eligible under the WOSB Program and other small businesses that are participating in the joint venture: ----------.] Each WOSB concern eligible under the WOSB Program participating in the joint venture shall submit a separate signed copy of the WOSB representation.

(7) Economically disadvantaged women-owned small business (EDWOSB) concern. [Complete only if the offeror represented itself as a WOSB concern eligible under the WOSB Program in (c)(6) of this provision.] The offeror represents that--

(i) It [ballot] is, [ballot] is not an EDWOSB concern, has provided all the required documents to the WOSB Repository, and no change in circumstances or adverse decisions have been issued that affects its eligibility; and

(ii) It [ballot] is, [ballot] is not a joint venture that complies with the requirements of 13 CFR part 127, and the representation in paragraph (c)(7)(i) of this provision is accurate for each EDWOSB concern participating in the joint venture. [The offeror shall enter the name or names of the EDWOSB concern and other small businesses that are participating in the joint venture: ----------.] Each EDWOSB concern participating in the joint venture shall submit a separate signed copy of the EDWOSB representation.

(8) Women-owned business concern (other than small business concern). (Complete only if the offeror is a women-owned business concern and did not represent itself as a small business concern in paragraph (c)(1) of this provision.) The offeror represents that it ( ) is, a women-owned business concern.

(9) Tie bid priority for labor surplus area concerns. If this is an invitation for bid, small business offerors may identify the labor surplus areas in which costs to be incurred on account of manufacturing or production (by offeror or first-tier subcontractors) amount to more than 50 percent of the contract price:

(10) (Complete only if the solicitation contains the clause at FAR 52.219-23, Notice of Price Evaluation Adjustment for Small Disadvantaged Business Concerns or FAR 52.219-25, Small Disadvantaged Business Participation Program-Disadvantaged Status and Reporting, and the offeror desires a benefit based on its disadvantaged status.)

(i) General. The offeror represents that either--

(A) It ( ) is, ( ) is not certified by the Small Business Administration as a small disadvantaged business concern and identified, on the date of this representation, as a certified small disadvantaged business concern in the CCR Dynamic Small Business Search database maintained by the Small Business Administration, and that no material change in disadvantaged ownership and control has occurred since its certification, and, where the concern is owned by one or more individuals claiming disadvantaged status, the net worth of each individual upon whom the certification is based does not exceed $750,000 after taking into account the applicable exclusions set forth at 13 CFR 124.104(c)(2); or

(B) It ( ) has, ( ) has not submitted a completed application to the Small Business Administration or a Private Certifier to be certified as a small disadvantaged business concern in accordance with 13 CFR 124, Subpart B, and a decision on that application is pending, and that no material change in disadvantaged ownership and control has occurred since its application was submitted.

(ii) Joint Ventures under the Price Evaluation Adjustment for Small Disadvantaged Business Concerns. The offeror represents, as part of its offer, that it is a joint venture that complies with the requirements in 13 CFR 124.1002(f) and that the representation in paragraph (c)(10)(i) of this provision is accurate for the small disadvantaged business concern that is participating in the joint venture. (The offeror shall enter the name of the small disadvantaged business concern that is participating in the joint venture: ____________.)

(11) HUBZone small business concern. (Complete only if the offeror represented itself as a small business concern in paragraph (c)(1) of this provision.) The offeror represents, as part of its offer, that--

(i) It [ ] is, [ ] is not a HUBZone small business concern listed, on the date of this representation, on the List of Qualified HUBZone Small Business Concerns maintained by the Small Business Administration, and no material changes in ownership and control, principal office, or HUBZone employee percentage have occurred since it was certified in accordance with 13 CFR Part 126; and

(ii) It [ ] is, [ ] is not a HUBZone joint venture that complies with the requirements of 13 CFR Part 126, and the representation in paragraph (c)(11)(i) of this provision is accurate for each HUBZone small business concern participating in the HUBZone joint venture. [The offeror shall enter the names of each of the HUBZone small business concerns participating in the HUBZone joint venture: _______.] Each HUBZone small business concern participating in the HUBZone joint venture shall submit a separate signed copy of the HUBZone representation.

(d) Certifications and representations required to implement provisions of Executive Order 11246--

(1) Previous Contracts and Compliance. The offeror represents that--

(i) It ( ) has, ( ) has not, participated in a previous contract or subcontract subject either to the Equal Opportunity clause of this solicitation, the and

(ii) It ( ) has, ( ) has not, filed all required compliance reports.

(2) Affirmative Action Compliance. The offeror represents that--

(i) It ( ) has developed and has on file, ( ) has not developed and does not have on file, at each establishment, affirmative action programs required by rules and regulations of the Secretary of Labor (41 CFR Subparts 60-1 and 60-2), or

(ii) It ( ) has not previously had contracts subject to the written affirmative action programs requirement of the rules and regulations of the Secretary of Labor.

(e) Certification Regarding Payments to Influence Federal Transactions (31 U.S.C. 1352). (Applies only if the contract is expected to exceed $150,000.) By submission of its offer, the offeror certifies to the best of its knowledge and belief that no Federal appropriated funds have been paid or will be paid to any person for influencing or attempting to influence an officer or employee of any agency, a Member of Congress, an officer or employee of Congress or an employee of a Member of Congress on his or her behalf in connection with the award of any resultant contract. If any registrants under the Lobbying Disclosure Act of 1995 have made a lobbying contact on behalf of the offeror with respect to this contract, the offeror shall complete and submit, with its offer, OMB Standard Form LLL, Disclosure of Lobbying Activities, to provide the name of the registrants.