Optics_SOW_(6-29-16)_(Rv2).pdf

Revision 2 June 29, 2016

Statement of Work (SOW)

Firearms Sighting Systems

1. BACKGROUND: The Department of Homeland Security (DHS), Customs and Border Protection (CBP) has a requirement for firearms mounted sighting systems to be used for training and law enforcement operations.

2. SCOPE: This statement of work delineates the required performance criteria for firearms mounted sighting systems for U.S. Customs and Border Protection (CBP), Department of Homeland Security (DHS).

The technical requirements for the firearms mounted sighting systems, to be acquired under this solicitation, are specified in section 4 of this solicitation.

3. APPLICABLE DOCUMENTS: None

4. TECHNICAL REQUIREMENTS:

NOTE: The items specified in the sections 4.1.3, 4.1.4, 4.1.5, 4.1.6, 4.1.7, 4.1.8, 4.1.9, 4.2.1, 4.2.2, 4.2.3, 4.2.4, 4.2.5, 4.2.6, 4.2.7, 4.2.8, and 4.3.3 must be permanently marked with individual and legible serial numbers.

4.1. Non-Magnified Optics

4.1.1. Fixed Rear Iron Sights This fixed rear sight shall be designed to be affixed to standard CBP duty flat top M4 receivers with 1913 Picatinny rails. The sight shall be affixed to the rail via a clamp and cross bolt, requiring a tool for installation and removal. The sight shall be equipped with a minimum of two apertures, a large aperture with an i.d. between .180” and .205” and a small aperture with an i.d.

between .065” and .075”. The sight shall allow a no-tool change of apertures by the user. The sight shall be equipped with a windage adjustment feature. The windage adjustment must require the use of a tool. Each adjustment of the windage must provide audible and tactile feedback. Each adjustment shall be secure and provide 0.5 MOA. The height of the center of the apertures shall be 1.40” from the top of the 1913 Picatinny rail. The body of the sight shall be made of hardened aluminum. The remaining components may be constructed of hardened aluminum or stainless steel. Sight shall be anodized black. Performance shall be equal to or better than Troy Fixed Rear Battle Sight with Dual Aperture.

4.1.2. Flip-Up Rear Iron Sights This flip-up rear sight shall be designed to be affixed to standard CBP duty flat top M4 receivers with 1913 Picatinny rails. The sight shall be affixed to the rail via clamp and cross bolt, requiring a tool for installation and removal. The sight shall be equipped with a minimum of two apertures, a large aperture with an i.d. between .180” and .205” and a small aperture with an i.d.

between .065” and .075”. The sight shall allow a no-tool change of apertures by the user. The sight shall be equipped with a windage adjustment feature. The windage adjustment must require the use of a tool. Each adjustment of the windage must provide audible and tactile feedback. Each adjustment shall be secure and provide 0.5 MOA. The height of the center of the apertures shall be 1.40” from the top of the Picatinny rail when in the flipped-up position. The height of the sight body shall be no more than .60” higher than the top of the Picatinny rail when in the flipped-down position. The sight shall be able to be flipped up by only swiveling the body of the sight upwards to a locked position. The sight must remain in the locked position until a de-locking mechanism is pressed by the user. The body of the sight shall be made of hardened T6 aluminum. The remaining components may be constructed of hardened T6 aluminum or stainless steel. Sight shall be black anodized. Performance shall be equal to or better than Diamondhead Classic Rear Combat Sight w/ Goal-Post Upper.

4.1.3. Non-magnified Battery Illuminated Miniature Reflex Optic This rifle mounted optic shall have an optical magnification no greater than 1x and contain a maximum of 3.25 MOA, red, LED aiming dot that may be adjustable or fixed. The optic shall be powered by a single battery with a battery life of more than 17,000 hours at a 50% setting in an average temperature of 70°F. The aiming dot cannot be visible from the front Optic and must be fully operable and unaffected by operational temperature ranges of -30° F and 130°F and relative humidity levels of up to 95%. The optic sight window shall not be any smaller than 22 mm X 16 mm. Optic shall operate during and after being fully immersed in water. Optic shall be resistant to shock, vibration, and chemical exposure. The dimensions of the optic (without mount) shall not exceed 46 mm by 29 mm by 26 mm. This optic shall be compatible with optic mount specified in section 4.4.1.

Performance shall be equal to or better than Trijicon Ruggedized Miniature Reflex (RMR) RM01-LED.

4.1.4. Non-magnified Tube Type Battery Powered Reflex Optic This rifle mounted tube type reflex optic shall have a clear optical aperture with a diameter between 25 mm and 27 mm. The optic shall provide no magnification (1x) and contain a 2 MOA, red, LED aiming dot. Reticle brightness shall have a minimum of 6 daytime settings and must be compatible with Night Vision Devices, by providing at least 3 reticle image settings that do not bloom when viewed with night vision devices. The optic shall be powered by a single battery with a battery life of more than 20,000 continuous hours when optic is set to display the aiming dot at 70% of full illumination at 70°F. The aiming dot cannot be visible from the front at a distance of 10’ when optic is set at the first and second lowest daytime settings. The windage and elevation adjustments must be covered and require the use of a tool for adjustments. Each adjustment must provide audible and tactile feedback. Each adjustment shall be secure and provide approximately 0.5 MOA adjustments, with a total minimum adjustment range of 34 MOA. Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130°F and relative humidity levels of up to 95%. Optic must be equipped with an integrated mounting system, compatible with a 1913 Picatinny rail, providing an absolute co-witness with an “F” marked front sight post. The body of the optic and mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. Optic and mount shall operate during and after being fully immersed in water. Optic and mount shall be resistant to shock, vibration, and chemical exposure. The dimensions of the optic (without mount) shall not exceed 47 mm in height, 126 mm in length, or 49 mm in width. Performance shall be equal to or better than Aimpoint PRO.

4.1.5. Non-magnified Battery Powered Red-Dot Sight w/semi-permanent mount. This rifle mounted tube type reflex optic shall have a clear optical aperture with a diameter between 18 mm and 21 mm. The sight shall have a front flip-up lens cover and a transparent rear flip-up lens cover included. The optic shall provide no magnification (1X) and contain a 2 MOA, red, LED aiming dot. Reticle brightness shall have a minimum of 8 daytime settings and must be compatible with Night Vision Devices, by providing at least 4 reticle image settings that do not bloom when viewed with night vision devices. The optic shall be powered by a single battery with a battery life of more than 20,000 continuous hours when optic is set to display the aiming dot at 70% of full illumination in 70°F. The aiming dot cannot be visible from the front at a distance of 10’ when optic is set at the first and second lowest daytime settings. The windage and elevation adjustments must be covered and require the use of a tool for adjustments. Each adjustment must provide audible and tactile feedback. Each adjustment shall be secure and provide approximately 0.5 MOA adjustments, with a total minimum adjustment range of 34 MOA.

Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130°F and relative humidity levels of up to 95%. Optic must be equipped with a mounting system, compatible with a 1913 Picatinny rail, providing an absolute co-witness with an “F” marked front sight post. The body of the optic and mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. Optic and mount shall operate during and after being fully immersed in water. Optic and mount shall be resistant to shock, vibration, and chemical exposure.

The dimensions of the optic (with mount) shall not exceed 68 mm in height, 73 mm in length, or 48 mm in width. Performance shall be equal to or better than the Aimpoint Micro T-2 w/ absolute co-witness riser and mount.

4.1.6. Non-magnified Battery Powered Red-Dot Sight w/o mount. This rifle mounted tube type reflex optic shall have a clear optical aperture with a diameter between 18 mm and 21 mm. The sight shall have a front flip-up lens cover and a transparent rear flip-up lens cover included. The optic shall provide no magnification (1X) and contain a 2 MOA, red, LED aiming dot. Reticle brightness shall have a minimum of 8 daytime settings and must be compatible with Night Vision Devices, by providing at least 4 reticle image settings that do not bloom when viewed with night vision devices. The optic shall be powered by a single battery with a battery life of more than 20,000 continuous hours when optic is set to display the aiming dot at 70% of full illumination at 70°F and relative humidity levels of up to 95%. The aiming dot cannot be visible from the front at a distance of 10’ when optic is set at the first and second lowest daytime settings. The windage and elevation adjustments must be covered and require the use of a tool for adjustments. Each adjustment must provide audible and tactile feedback. Each adjustment shall be secure and provide approximately 0.5 MOA adjustments, with a total minimum adjustment range of 34 MOA. Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130°F and relative humidity levels of up to 95%. The body of the optic shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. This optic shall be compatible with optional quick-detach optic mount specified in section 4.4.2 of this document. Optic shall operate during and after being fully immersed in water. Optic shall be resistant to shock, vibration, and chemical exposure. The dimensions of the optic (without mount) shall not exceed 36 mm in height, 73 mm in length, or 42 mm in width.

Performance shall be equal to or better than the Aimpoint Micro T-2 w/o mount.

4.1.7. Non-magnification Battery Powered Compact Red Dot Optic This rifle mounted optic shall have an objective lens with a diameter between 19 mm and 21 mm. The optic shall be receptive to and supplied with a kill flash device which can be threaded on to the exterior of the objective lens. The optic shall provide no magnification (1x) and contain dual LED-illuminated reticle options which can be toggled by the user. The reticles shall be a 2 MOA red aiming dot, and a 65 MOA red circle with red dot. The optic shall be powered by a single battery and shall have 12 illumination settings, including two night vision settings. The optic illumination controls shall be located on the top of the optic to allow ambidextrous control. The optic shall have a battery saving feature that senses motion to power down when motionless after approximately 120 seconds of nonuse and power up to the previous setting as soon as motion is sensed, extending possible battery life to beyond 50,000 hours of normal use at medium setting. The aiming dot cannot be visible from the front at a distance of 10’ when optic is set at the first and second lowest daytime settings. The windage and elevation adjustments must be covered and require the use of a tool for adjustments. The sight shall have an adjustment range of 50 MOA; adjustable in .5 MOA increments. Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130°F and relative humidity levels of up to 95%. Optic must be equipped with an integrated mounting system, compatible with a 1913 Picatinny rail, providing an absolute co-witness with an “F” marked front sight post.

The body of the optic and mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable dark finish. Optic weight shall be less than 3.5 oz. Optic shall continually operate during and after being fully submersed in water and maintain a fog proof lens. Optic shall be resistant to shock, vibration, and chemical exposure. The dimensions of this rifle mounted optic shall be not exceed 68 mm in length, 42 mm in width, and 37 mm in height.

Performance shall be equal to or better than Sig Sauer ROMEO4m.

4.1.8. Non-magnified Battery Powered Increased Objective Lens Optic w/ standard semi-permanent mount This rifle mounted optic shall have a clear objective aperture with a diameter of at least 20 mm and an objective lens with a minimum diameter of 25 mm. The optic shall provide no magnification (1x) and contain a 2 MOA, red, LED aiming dot. The sight shall be night vision compatible with a minimal two night vision settings. Dot brightness shall have a minimum of 6 daylight settings. The optic shall be powered by a single battery with a battery life of more than 40,000 continuous hours at 60% of maximum power setting at 70°F. The aiming dot cannot be visible from the front at a distance of 10’ when optic is set at the first and second lowest daytime settings. The sight shall have an adjustment range of 68 MOA; adjustable in .5 MOA increments. Optic must be fully operable and unaffected by operational temperature ranges of - 30° F and 130°F and relative humidity levels of up to 95%. Optic must be equipped with a mounting system, compatible with a 1913 Picatinny rail, providing an absolute co-witness with an “F” marked front sight post. The body of the optic and mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. Optic and mount shall continually operate during and after being fully immersed in water. Optic and mount shall be resistant to shock, vibration, and chemical exposure. The dimensions of the optic (with mount) shall not exceed 75 mm in height, 67 mm in length, or 41 mm in width. Performance shall be equal to or better than Trijicon MRO w/ standard absolute co-witness mount.

4.1.9. Non-magnified Battery Powered Increased Objective Lens Optic w/o mount This rifle mounted optic shall have a clear objective aperture with a diameter of at least 20 mm and an objective lens with a minimum diameter of 25 mm. The optic shall provide no magnification (1x) and contain a 2 MOA, red, LED aiming dot. The sight shall be night vision compatible with a minimal two night vision settings. Dot brightness shall have a minimum of 6 daylight settings.

The optic shall be powered by a single battery with a battery life of more than 40,000 continuous hours at 60% of maximum power setting in 70°F. The aiming dot cannot be visible from the front at a distance of 10’ when optic is set at the first and second lowest daytime settings. The sight shall have an adjustment range of 68 MOA, adjustable in .5 MOA increments. Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130°F and relative humidity levels of 95%. The body of the optic shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. This optic shall be compatible with optional optic mounting systems specified in sections 4.4.3 and 4.4.4 of this document. Optic shall continually operate during and after being fully immersed in water. Optic shall be resistant to shock, vibration, and chemical exposure. The dimensions of the optic (without mount) shall not exceed 51 mm in height, 67 mm in length, or 41 mm in width. Performance shall be equal to or better than Trijicon MRO w/o mount.

4.2. Magnified Optics

4.2.1. Magnified Non-Battery Illuminated Optic This rifle optic shall have an objective lens between 23 mm and 25 mm. The sight shall have a fixed optical magnification of 1.5X. The field of view shall be a minimum of 4.9 degrees. The reticle needs to be with a dual illuminated red 8 MOA triangle reticle. The optic shall feature a fiber optic illuminated reticle that adjusts the brightness based on available ambient light with a back-up illumination by tritium or equivalent, providing reticle illumination for a minimum of 12 years continuous use. The optic shall have an eye relief between 3 and 4 inches. The windage and elevation adjustments must be covered and require the use of a tool for adjustments. The sight shall be adjustable in approximately .35 MOA increments. Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130°.

Optic must be equipped with an integrated mounting system, mountable to a CBP-issued M4 with a flat top 1913 Picatinny rail.

The overall dimensions of the optic (without mount) shall not exceed (LxWxH) 67 mm x 43 mm x 52 mm. This optic shall be compatible with optional standard or quick-detach optic mounts specified in section 4.4.5 and 4.4.6 of this document. The body of the optic and mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. The optic shall operate during and after being fully immersed in water. Optic and mount shall be resistant to shock, vibration, and chemical exposure.

Performance shall be equal to or better than the Trijicon TA45R2 1.5x24.

4.2.2. Magnified Non-Battery Illuminated Optic This rifle optic shall have an objective lens between 31 mm and 33 mm. The sight shall have a fixed optical magnification of 4X. The field of view shall be a minimum of 7 degrees. The reticle needs to be with a dual illuminated red 5.53 MOA triangle reticle. The optic shall feature a fiber optic illuminated reticle that adjusts the brightness based on available ambient light with a back-up illumination by tritium or equivalent, providing reticle illumination for a minimum of 12 years continuous use. The optic shall have an eye relief between 3 and 4 inches. The windage and elevation adjustments must be covered and require the use of a tool for adjustments. The sight shall be adjustable in approximately .35 MOA increments. Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130°. Optic must be equipped with an integrated mounting system (TA51 or equivalent), mountable to a CBP-issued M4 with a flat top 1913 Picatinny rail. The overall dimensions of the optic (without mount) shall not exceed (LxWxH) 67 mm x 43 mm x 52 mm.

This optic shall be compatible with optional standard or quick-detach optic mounts specified in section 4.4.5 and 4.4.6 of this document.

The body of the optic and mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. The optic shall continually operate during and after being fully immersed in water. Optic and mount shall be resistant to shock, vibration, and chemical exposure. Performance shall be equal to or better than the Trijicon TA31F: 4X32.

4.2.3. Variable Magnification Battery Powered Illuminated Optic This rifle mounted optic shall have a clear optical aperture with an objective lens diameter between 23 mm and 25 mm. The optic shall provide variable magnification of 1x to 6x. The optic must be able to quickly transition from 1x to 6x using an integrated dial fin, allowing easy transition through magnification settings. Field of view shall be 18 degrees at 1x and 3 degrees at 6x. The reticle shall be first focal plane and the pattern shall be a segmented circle with crosshair and milliradian (MIL) subtension lines compatible with multiple calibers and bullet weights. Eye relief shall be a constant distance between

3.5 inches and 4.5 inches regardless of magnification setting. The reticle shall have at least 6 adjustable brightness settings and shall be LED illuminated in red. The optic shall be powered by a single battery with a battery life of at least 700 continuous hours when optic is set to illuminate the reticle at a 65% brightness setting. The illuminated reticle cannot be visible from the front. Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130° and up to 95% relative humidity levels. Optic shall continually operate during and after being fully immersed in water.

Optic shall be constructed of hardened aluminum housing that is anodized or coated in durable black finish. The overall dimensions of the optic shall not exceed (LxWxH) 256 mm x 65 mm x 70 mm. Optic shall continually operate during and after being fully immersed in water. Optic must be resistant to shock, vibration, and chemical exposure. This optic shall be compatible with optional standard or quick-detach optic mounts specified in section 4.4.7 of this document.

Performance shall be equal to or better than Trijicon VCOG with USBP Pattern Reticle.

4.2.4. Low Power Dual Field of View Battery Powered Illuminated Optic This rifle mounted optic shall have a clear objective aperture with a diameter of at least 30 mm and an objective lens with a minimum diameter of 30 mm. The optic shall provide dual magnification settings that allow instantaneous switch between 1x and 4x magnification settings with no more than the movement of a switch between the two designated switch points of 1x and 4x. The optic shall provide a 24 degree field of view when set to 1x and a 6 degree field of view when set to 4x. The optic shall contain a 6 MOA (at 1x), red, LED aiming dot, accompanied with a ballistic drop reticle calculated for 7.62 located in the second focal plane. Both red-dot and crosshairs shall be able to be selected for illumination by the user. The sight shall be night vision compatible and provide a minimal of five total illumination settings for the dot, and five for the crosshairs. When not illuminated, the crosshairs and ballistic drop reticle shall remain visible. The optic shall be powered by a single battery with a battery life of more than 600 continuous hours at 70°F.

The aiming dot cannot be visible from the front at a distance of 48” when optic is set at the first or second lowest daytime settings. In addition to the reticle, the optic shall be equipped with a ring rear sight and post front sight, affixed to the top of the optic. The sight shall have a minimum adjustment range of 100 MOA, adjustable in .5 MOA increments. Adjustments to windage and elevation must be made externally to the optic by adjusting the orientation of the optic to the mounting system. Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130°F and relative humidity levels of up to 95%. Optic must be equipped with a throw lever attachment mounting system, compatible with a 1913 Picatinny rail. The body of the optic and mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable dark tan finish. Optic shall continually operate during and after being fully immersed in water. Optic shall be resistant to shock, vibration, and chemical exposure. The dimensions of the optic (with mount) shall not exceed 77 mm in height, 153 mm in length, or 73 mm in width.

Performance shall be equal to or better than Elcan SpecterDR 1-4x

DFOV14-T2.

4.2.5. Mid Power Dual Field of View Battery Powered Illuminated Optic This rifle mounted optic shall have a clear objective aperture with a diameter of at least 30 mm and an objective lens with a minimum diameter of 30 mm. The optic shall provide dual magnification settings that allow instantaneous switch between 1.5x and 6x magnification settings with no more than the movement of a switch between the two designated switch points of 1.5x and 6x. The optic shall provide a 16 degree field of view when set to 1.5x and a 4 degree field of view when set to 6x. The optic shall contain a 6 MOA (at 1.5x), red, LED aiming dot, accompanied with a ballistic drop reticle calculated for 7.62 located in the second focal plane. Both red-dot and crosshairs shall be able to be selected for illumination by the user. The sight shall be night vision compatible and provide a minimal of five total illumination settings for the dot, and five for the crosshairs. When not illuminated, the crosshairs and ballistic drop reticle shall remain visible. The optic shall be powered by a single battery with a battery life of more than 600 continuous hours at 70°F. The aiming dot cannot be visible from the front at a distance of 48” when optic is set at the first or second lowest daytime settings. In addition to the reticle, the optic shall be equipped with a ring rear sight and post front sight, affixed to the top of the optic. The sight shall have a minimum adjustment range of 100 MOA, adjustable in .5 MOA increments. Adjustments to windage and elevation must be made externally to the optic by adjusting the orientation of the optic to the mounting system. Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130°F and relative humidity levels of up to 95%. Optic must be equipped with a throw lever attachment mounting system, compatible with a 1913 Picatinny rail. The body of the optic and mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable dark tan finish. Optic shall continually operate during and after being fully immersed in water. Optic shall be resistant to shock, vibration, and chemical exposure. The dimensions of the optic (with mount) shall not exceed 77 mm in height, 183 mm in length, or 75 mm in width. Performance shall be equal to or better than Elcan SpecterDR 1.5-6x DFOV156

4.2.6. Variable Magnified Battery Operated Illuminated Tubular Patrol Optic This rifle optic shall have an objective clear aperture of at least

19.5 mm. The optic shall provide variable magnification of 1.5x to 4x.

The optic shall provide a minimum linear field of view range of 30’ to 74’ at 100 yards. The reticle shall be located in the second focal plane and comprised of heavy posts connected by fine stadia lines, creating crosshairs, with tic marks, calibrated in mil-based increments. The center of the reticle shall contain a circle center, at the center of the circle shall be an adjustable illuminated red dot with at least 10 brightness settings. The optic shall be powered by a single battery. The optic shall have an eye relief between 3.7 and 4.1 inches regardless of magnification setting. The windage and elevation adjustments must provide audible and tactile feedback with each adjustment of .10 mil per click. The optic must provide a total minimum adjustment range of 90 MOA for both windage and elevation. Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130°. This optic shall be compatible with optional quick-detach optic mount specified in section

4.4.8 of this document. The overall dimensions of the optic (without mount) shall not exceed (LxW) 9.5” x 2.5” with a main tube diameter of 30 mm. The body of the optic shall be made of high strength aluminum that is anodized or coated in durable black finish. The optic shall operate during and after being fully immersed in water.

Optic shall be resistant to shock, vibration, and chemical exposure.

Performance shall be equal to or better than the Leupold VX/R Patrol 1.25-4x20mm #113769.

4.2.7. Variable Magnification Illuminated Tubular Optic This rifle optic shall have an objective clear aperture of 24 mm. The optic shall provide variable magnification of 1.1x to 8x. The optic shall provide a minimum linear field of view range of 32’ to 91’ at 100 yards. The reticle shall be a Horus H27D reticle, located in the first focal plane, containing an illuminated circular center and is calibrated in mil-based increments. The optic shall be powered by a single battery. The optic shall have an eye relief between 3.3 and 3.7 inches regardless of magnification setting. The windage and elevation adjustments must automatically lock and provide audible and tactile feedback with each adjustment of .10 mil per click. The optic must provide a total minimum adjustment range of 140 MOA for both windage and elevation. Optic must be fully operable and unaffected by operational temperature ranges of -30° F and 130°. This optic shall be compatible with optional quick-detach optic mount specified in section

4.4.8 of this document. The overall dimensions of the optic (without mount) shall not exceed (LxW) 11.8” x 2.5” with a main tube diameter of 34 mm. The body of the optic shall be made of high strength aluminum that is anodized or coated in durable black finish. The optic shall operate during and after being fully immersed in water.

Optic shall be resistant to shock, vibration, and chemical exposure.

Performance shall be equal to or better than the Leupold Mark 8 1.1- 8X24mm M5B1 #112564.

4.2.8. Variable Magnified Non-Battery Non-Illuminated Tubular Optic This rifle optic shall have an objective clear aperture of 44 mm. The optic shall provide variable magnification of 3x to 18x. The optic shall provide a minimum linear field of view range of 7’ to 35’ at 100 yards.

The reticle shall be a Horus H59 reticle, located in the first focal plane, able to be illuminated with at least 10 levels of reticle brightness and is calibrated in mil-based increments. The optic shall be powered by a single battery. The optic shall have an eye relief between 3.8 and 3.9 inches regardless of magnification setting. The windage and elevation adjustments must automatically lock and provide audible and tactile feedback with each adjustment of .10 mil per click. The optic must provide a total minimum adjustment range of 45 MOA for windage and 85 MOA for elevation. Optic must be fully operable and unaffected by operational temperature ranges of - 30° F and 130°. This optic shall be compatible with optional quick-detach optic mount specified in section 4.4.8 of this document. The overall dimensions of the optic (without mount) shall not exceed (LxW) 11.9” x 2.5” with a main tube diameter of 34 mm. The body of the optic shall be made of high strength aluminum that is anodized or coated in durable black finish. The optic shall operate during and after being fully immersed in water. Optic shall be resistant to shock, vibration, and chemical exposure. Performance shall be equal to or better than the Leupold Mark 6 3-18X44mm M5B2 #119213.

4.3. Supplemental Devices

4.3.1. Non-Battery 3x Magnifier This rifle mounted supplemental magnifier shall have a fixed 3x magnification and be compatible with non-magnified optics specified in section 4.1. The magnifier shall not have an aiming reticle or require the use of a battery. Eye relief shall be between 2 and 3 inches. The field of view shall be between 6.5 and 7.5 degrees. The optic shall have a manual dioptric adjustment for focal tuning. The magnifier must be fog resistant and continually operable after being submersed in water. The optic shall have a mount compatible with 1913 Picatinny rails on CBP issued M4 flat top rifles at an absolute co-witness height. The mount must allow rapid transition from 3x to 1x magnification. Performance shall be equal to or greater than Aimpoint 3XMAG-1 with Flipmount.

4.3.2. Non-Battery 6x Magnifier This rifle mounted supplemental magnifier shall have a fixed 6x magnification and be compatible with non-magnified optics specified in section 4.1. The magnifier shall not have an aiming reticle or require the use of a battery. Eye relief shall be between 2 and 3 inches. The field of view shall be between 2.5 and 3.5 degrees. The optic shall have a manual dioptric adjustment for focal tuning. The magnifier must be fog resistant and continually operable after being submersed in water. The optic shall have a mount compatible with 1913 Picatinny rails on CBP issued M4 flat top rifles at an absolute co-witness height. The mount must allow rapid transition from 6x to 1x magnification. Performance shall be equal to or greater than Aimpoint 6XMAG-1 with Flipmount.

4.3.3. Target Pointer and Aiming Laser This rifle mounted target pointer aiming laser shall provide integrated infrared and visible aiming lasers able to be used with or without night vision devices. The device shall be powered by a single battery with a battery life exceeding 6 hours, when in high settings. The pointer shall provide co-aligned visual and infrared lasers, allowing the laser sight to be useful in daytime conditions. The visible beam shall have a beam divergence no greater than .5 mrad and a range of 25 meters. The infrared laser must be fully compatible with night vision devices and produce an infrared beam divergence no greater than .5 mrad with a range of 2000 meters. In addition, the device must be equipped with an infrared illuminator that will provide contrast to the environment when viewed through night vision devices, regardless of the presence of natural light. The device must provide both windage and elevation adjustments allowing for precision accuracy adjustments. The unit must not exceed a weight of 7.6 oz. with batteries. The dimensions of the optic (without mount) shall not exceed 41 mm in height, 117 mm in length, or 72 mm in width. Performance shall be equal to or greater than EOTech ATPIAL (AN/PEQ-15).

4.4. Optical Sight Mounts

4.4.1. Miniature Reflex Quick Detach Optic Mount This optic mount shall be compatible with optics specified in sections 4.1.3. The mount shall be compatible with 1913 Picatinny rails and utilize one quick detach (QD) lever mechanism that secures the mount to the rail with a manually adjustable cross bolt clamping design oriented perpendicular to long axis of rail. The QD lever tension resistance adjustment mechanism shall be adjustable to accommodate out-of-spec or worn 1913 Picatinny rails, and shall require a standard slot screwdriver to make tension adjustments. The QD lever shall be adjustable to rotate 180 degrees to allow for ambidextrous lever orientation. QD lever tension resistance shall be manually adjustable with the QD lever in the closed locked position, as well as the open unlocked position. The mount's rail locking mechanism shall not abrade or wear the 1913 Picatinny rail after fifty (50) removal & remounting cycles to avoid degradation of the 1913 Picatinny rail's dimensional specifications & tolerances. The mount shall utilize a quick detach lever system that automatically locks when QD lever is closed, and which manual manipulation to unlock and open. The mount shall not require tools for removal or mounting once initial tension resistance adjustment is made for fitting of mount to the rail. The mount shall retain zero with a shift of less than .03 MOA after live fire testing in excess of 4500 rounds of 5.56 ammunition and mechanical stresses. The mount shall return to zero with less than .2 MOA variance after fifty (50) removal and remounting cycles during live fire. Mount shall provide the optic with an absolute co-witness of an “F” marked front sight post. The mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. Performance shall be equal to or greater than Global Defense Initiatives MR5-OSM Optical Sight Mount for Trijicon Red Dot Reflex Sight

4.4.2. Non-Magnified Red Dot Quick Detach Optic Mount This optic mount shall be compatible with optics specified in sections 4.1.6. The mount shall be compatible with 1913 Picatinny rails and utilize one quick detach (QD) lever mechanism that secures the mount to the rail with a manually adjustable cross bolt clamping design oriented perpendicular to long axis of rail. The QD lever tension resistance adjustment mechanism shall be adjustable to accommodate out-of-spec or worn 1913 Picatinny rails, and shall require a standard slot screwdriver to make tension adjustments. The QD lever shall be adjustable to rotate 180 degrees to allow for ambidextrous lever orientation. QD lever tension resistance shall be manually adjustable with the QD lever in the closed locked position, as well as the open unlocked position. The mount's rail locking mechanism shall not abrade or wear the 1913 Picatinny rail after fifty (50) removal & remounting cycles to avoid degradation of the 1913 Picatinny rail's dimensional specifications & tolerances. The mount shall utilize a quick detach lever system that automatically locks when QD lever is closed, and which manual manipulation is required to unlock and open. The mount shall not require tools for removal or mounting once initial tension resistance adjustment is made for fitting of mount to the rail. The mount shall be certified retain zero with a shift of less than .03 MOA after live fire testing in excess of 4500 rounds of 5.56 ammunition and mechanical stresses. The mount shall return to zero with less than .2 MOA variance after fifty (50) removal and remounting cycles during live fire. Mount shall provide the optic with an absolute co-witness of an “F” marked front sight post. The mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. Performance shall be equal to or greater than Global Defense Initiatives MT5-OSM Optical Sight Mount for T2.

4.4.3. Non-Magnified Red Dot Standard Semi-Permanent Optic Mount This optic mount shall be compatible with optics specified in sections

4.1.9. The mount shall be compatible with 1913 Picatinny rails and shall utilize two tool installed cross bolts to secure the mount to the rail. The mount shall be attached to the optic with four screws that require a tool for installation. The mount shall not exceed an overall length of 1.75 inches. The mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. Performance shall be equal to or better than Trijicon MRO Full Co-witness Adapter AC32068.

4.4.4. Non-Magnified Red Dot Quick Detach Optic Mount This optic mount shall be compatible with optics specified in sections 4.1.9. The mount shall be compatible with 1913 Picatinny rails and utilize one quick detach (QD) lever mechanism that secures the mount to the rail with a manually adjustable cross bolt clamping design oriented perpendicular to long axis of rail. The QD lever tension resistance adjustment mechanism shall be adjustable to accommodate out-of-spec or worn 1913 Picatinny rails, and shall require a standard slot screwdriver to make tension adjustments. The QD lever shall be adjustable to rotate 180 degrees to allow for ambidextrous lever orientation. QD lever tension resistance shall be manually adjustable with the QD lever in the closed locked position, as well as the open unlocked position. The mount's rail locking mechanism shall not abrade or wear the 1913 Picatinny rail after fifty (50) removal & remounting cycles to avoid degradation of the 1913 Picatinny rail's dimensional specifications & tolerances. The mount shall utilize a quick detach lever system that automatically locks when QD lever is closed, and which manual manipulation to unlock and open. The mount shall not require tools for removal or mounting once initial tension resistance adjustment is made for fitting of mount to the rail. The mount shall retain zero with a shift of less than .03 MOA after live fire testing in excess of 4500 rounds of 5.56 ammunition and mechanical stresses. The mount shall return to zero with less than .2 MOA variance after fifty (50) removal and remounting cycles during live fire. Mount shall provide the optic with an absolute co-witness of an “F” marked front sight post. The mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. Performance shall be equal to or greater than Global Defense Initiatives MS5-OSM Optical Sight Mount for MRO.

4.4.5. Fixed Magnification Standard Optic Mount

REMOVED

4.4.6. Fixed Magnification Quick Detach Optic Mount

REMOVED

4.4.7. Variable Magnification Quick Detach Optic Mount This optic mount shall be compatible with optics specified in section 4.2.3. The mount shall be compatible with 1913 Picatinny rails and which utilizes two quick detach (QD) lever mechanisms that secure the mount to the rail; each with a manually adjustable cross bolt clamping design oriented perpendicular to long axis of the rail. The QD lever tension resistance adjustment mechanism shall be adjustable to accommodate out-of-spec or worn 1913 Picatinny rails, and shall require a standard slot screwdriver to make tension resistance adjustments. The QD lever shall be adjustable to rotate 180 degrees to allow for ambidextrous lever orientation. QD lever tension resistance shall be manually adjustable with the QD lever in the closed locked position, as well as the open unlocked position. The mount's rail locking mechanism shall not abrade or wear the 1913 Picatinny rail after fifty (50) removal & remounting cycles to avoid degradation of the 1913 Picatinny rail's dimensional specifications & tolerances. The mount shall utilize a quick detach lever system that automatically locks when QD lever is closed, and which requires manual manipulation to unlock and open. QD lever mount shall not require tools for removal or mounting once initial tension resistance adjustment is made for fitting of mount to the rail. The mount shall retain zero with a shift of less than .03 MOA after live fire testing in excess of 4500 rounds of 5.56 ammunition and mechanical stresses. The mount shall return to zero with less than .2 MOA variance after fifty (50) removal and remounting cycles during live fire. The mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. Performance shall be equal to or greater than Global Defense Initiatives V-COM-L Combat Optic Mount.

4.4.8. 34 MM Quick Detach Optic Mount This optic mount shall be compatible with the 34 MM optics specified in section 4.2.7 and

4.2.8. The mount shall be compatible with 1913 Picatinny rails and which utilizes two quick detach (QD) lever mechanisms that secure the mount to the rail; each with a manually adjustable cross bolt clamping design oriented perpendicular to long axis of the rail. The QD lever tension resistance adjustment mechanism shall be adjustable to accommodate out-of-spec or worn 1913 Picatinny rails, and shall require a standard slot screwdriver to make tension resistance adjustments. The QD lever shall be adjustable to rotate 180 degrees to allow for ambidextrous lever orientation. QD lever tension resistance shall be manually adjustable with the QD lever in the closed locked position, as well as the open unlocked position. The mount's rail locking mechanism shall not abrade or wear the 1913 Picatinny rail after fifty (50) removal & remounting cycles to avoid degradation of the 1913 Picatinny rail's dimensional specifications & tolerances. The mount shall utilize a quick detach lever system that automatically locks when QD lever is closed, and which requires manual manipulation to unlock and open. QD lever mount shall not require tools for removal or mounting once initial tension resistance adjustment is made for fitting of mount to the rail. The mount shall retain zero with a shift of less than .03 MOA after live fire testing in excess of 4500 rounds of 5.56 ammunition and mechanical stresses. The mount shall return to zero with less than .2 MOA variance after fifty (50) removal and remounting cycles during live fire. The mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. Performance shall be equal to or greater than Global Defense Initiatives P-ROM- L Rifle Optic Mount (34 mm).

4.4.9. 30 MM Quick Detach Optic Mount This optic mount shall be compatible with the 30 MM optics specified in section 4.2.6. The mount shall be compatible with 1913 Picatinny rails and which utilizes two quick detach (QD) lever mechanisms that secure the mount to the rail; each with a manually adjustable cross bolt clamping design oriented perpendicular to long axis of the rail. The QD lever tension resistance adjustment mechanism shall be adjustable to accommodate out-of-spec or worn 1913 Picatinny rails, and shall require a standard slot screwdriver to make tension resistance adjustments. The QD lever shall be adjustable to rotate 180 degrees to allow for ambidextrous lever orientation. QD lever tension resistance shall be manually adjustable with the QD lever in the closed locked position, as well as the open unlocked position. The mount's rail locking mechanism shall not abrade or wear the 1913 Picatinny rail after fifty (50) removal & remounting cycles to avoid degradation of the 1913 Picatinny rail's dimensional specifications & tolerances. The mount shall utilize a quick detach lever system that automatically locks when QD lever is closed, and which requires manual manipulation to unlock and open. QD lever mount shall not require tools for removal or mounting once initial tension resistance adjustment is made for fitting of mount to the rail. The mount shall retain zero with a shift of less than .03 MOA after live fire testing in excess of 4500 rounds of 5.56 ammunition and mechanical stresses. The mount shall return to zero with less than .2 MOA variance after fifty (50) removal and remounting cycles during live fire. The mount shall be made of high strength aluminum and/or steel that is anodized or coated in durable black finish. Performance shall be equal to or greater than Global Defense Initiatives P-ROM-L Rifle Optic Mount (30mm).

5. DELIVERABLES AND DELIVERY SCHEDULE: Vendor shall provide 48 hour notification to location POC to allow for preparations for delivery. Delivery shall be made within 30 days of vendor receiving delivery order.

6. GOVERNMENT-FURNISHED EQUIPMENT AND INFORMATION: N/A

7. PLACE OF PERFORMANCE: Items will be shipped to the government locations listed in the deliverables section above.

8. PERIOD OF PERFORMANCE: Date of calendar award for 1 year plus 4 one-year option periods.

9. SECURITY: This work will be unclassified.

10. SPECIAL CONSIDERATIONS: None