FA821321R3009 Attachments.PDF

PDF 6 MB Posted Dec 28, 2020

Attached to: 1 Way Transfer and B1B Delays Federal contract opportunity
Solicitation number: FA821321R3009
Issued by: Department of the Air Force Materiel Command Lifecycle Management Center Hill Air Force Base

About this file

Written by GovTribe AI · Dec 28, 2023

This is a competitive solicitation for one-way transfer initiators and B1B time delay initiators. The solicitation seeks these products to support the Department of the Air Force Materiel Command Lifecycle Management Center at Hill Air Force Base. Responses are due by 21 December 2021. The solicitation is for firm-fixed-price contracts and will result in multiple awards. The document provides templates for reporting shipment information and engineering data lists to support contract performance.

View the file

Other files for this federal contract opportunity

Other files attached to 1 Way Transfer and B1B Delays, newest first.
File	Type	Posted
13 FA821321R3009 AMEND 3.pdf	PDF	Feb 11, 2021
08 FA821321R3009 AMEND 2.pdf	PDF	Jan 8, 2021
05 FA821321R3009 Solicitation AMEND 1.pdf	PDF	Jan 4, 2021
FA821321R3009 Solicitation.pdf	PDF	Dec 28, 2020

On GovTribe

Work with this file on GovTribe

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

Contractor Name

CAGE code

PR No. FD2020-

Date Contract Awarded

Final Delivery Date (FDD)

Program Name

DODIC

Part Number

The contractor, at a minimum, shall allow DCMA to inspect the following points:

Mandatory - M: Stamp and/ or Signature on original documentation (i.e., Mfg. Planning, ATP, FAT Report, etc.)

Witness - W: GSI required to attend per comment section.

Verification - V: Stamp and/or Signature required unless noted otherwise (may be done by written verification) Monitor - R: Will monitor testing, may reduce to verification per comment section.

Notify - N: By phone or email prior to action.

Additional requirements: (DCMA reserves the right to impose additional inspection points as deemed necessary.)

Prepared by:

Date

THIS PLANNING SHEET WILL BE UPDATED IF NECESSARY.

QUALITY ASSURANCE LETTER OF INSTRUCTION

Planning Requirements

COMMENTS

NOTICE

Engineer Signature

Rev Date: 5 May 2019

Sheet1

Text46: 10 May 2019

2019-05-10T13:20:52-0600

TIDWELL.QUINN.RAY.1241451913

undefined_9: N

Text32: 9. Additional Requirements undefined_8: M

Text31: 8. Shippers (DD250, Reports) undefined_7: M

Text30: 7. AMMO Data Card Review undefined_6: V

Text29: 6. Preparation for Shipment undefined_5: W

Text28: 5. LAT undefined_4: V

Text27: 4. LAT Sample Selection undefined_3: V

Text26: 3. X-Ray/N-Ray undefined_2: V

Text25: 2. Leak Test undefined: V

Text36: 1. Explosive Weight

2. Verify gross leak and fine leak check are performed.

3. Ensure film labeling correct. Ensure radiographic film is readable and well-defined. DCMA is not required to interpret film.

4. Randomly select LAT units per latest government approved ATP.

5. Testing should occur in accordance with latest government approved ATP. Prior to LAT ensure proper calibration and validation of all test equipment. Witness proper test setup and at least the first 3 functional tests. Further witnessing may be required if there are known concerns with the item or requested by Government Engineer.

6. Ensure Paperwork is correct.

7. Verify all energetic materials: list original manufacturer,original lot number, and latest certification/recertification date < 24 months.

8. Ensure Paperwork is correct. Verify Packaging, Packing, Preservation & Marking (PPP&M)

9. Any additional requirements imposed by DCMA shall be approved by Government Project Engineer

Text24: 1.Inspection

Part Number: 6036200-1, 816890-1

DODIC: MH61

Text20:

Text19:

Part Number Line 2:

Contract No: 20-50073

Date Contract Awarded:

Final Delivery Date FDD:

Program Name:

ENGINEERING DATA LIST

DATE:

13 APR 2016

REVISION: 9 *HISTORY*

CAGE:

76301

PAGE:

NSN:

1377011676621ES

DATA TECH:

Williams, Mark S

END ITEM:

B-1B & F-15

ORGANIZATION/OFFICE SYMBOL:

429 SCMS GUMACB/

MANUFACTURER NAME:

BOEING COMPANY, THE

REFERENCE NUMBER:

68-710077-103

NOUN:

INITIATOR,PROPELLAN

LINE/

SUB CAGE

ENG DRAWING NUM/ ACCOMP

DOC NUM REV

SHEETS

FURN

CODE

DIST

CODE NOUN REMARKS

L 76301 PS68-710077 C S INITIATOR, ONE-WAY

TRANSFER

STANDARD ENGINEERING TEXT

Williams, Mark S 13 APR 2016

RELEASE OF THIS DATA TO A FOREIGN-OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

NAME: DATE:

C - CLASSIFIED DOCUMENT.

S - FURNISHED WITH SOLICITATION.

M - STABLE BASE DRAWING REQUIRED; FURNISHED WITH

CONTRACT AWARD.

X - DATA SUPPLIED (NOT IN JEDMICS).

R - FURNISHED BY PCO UPON REQUEST.

P - PARTIAL DOCUMENT FURNISHED.

V - VENDOR DRAWING; (NOT PROVIDED).

G - GOV'T DOCUMENT.

O - OTHERS, CONTRACTOR MUST ACQUIRE.

A- DATA NOT AVAILABLE.

FURNISHED METHOD CODE LEGEND:

Page 1 of 1EDL Version 9Generated by PRPS using Jasper Reports on 07 Jul 2020

13 APR 2016

REVISION: 7 *HISTORY*

43999

1377012203746ES

B-1B & F-15

L325C2011

INITIATOR,PROPELLAN

L 43999 L0000024 W S FINISH DOCUMENT B-1B Williams, Mark S 13 APR 2016

W/EO L615558

L 43999 L325C2011 C S ONE WAY TRANSFER

Williams, Mark S 13 APR 2016

RELEASE OF THIS DATA TO A FOREIGN-OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

Page 1 of 1EDL Version 7Generated by PRPS using Jasper Reports on 07 Jul 2020

16 MAY 2017

REVISION: 13 *HISTORY*

1377012297600ES

Tilton, Richard J

INITIATOR,CARTRIDGE

L 43999 L325C2011 C 0000 S PROCUREMENT

SPECIFICATION

L 43999 L0000024 W S FINISH SPECIFICATION Tilton, Richard J 16 MAY 2017

WITH L615558

Tilton, Richard J 16 MAY 2017

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

Page 1 of 1EDL Version 13Generated by PRPS using Jasper Reports on 04 Jun 2019

22 JAN 2018

REVISION: 11 *HISTORY*

1377012321677ES

B-1B AIRCRAFT

L325C2011-VI

L 43999 L325C2011 C S PROCUREMENT

L 43999 L0000024 W S FINISH SPECIFICATION Tilton, Richard J 22 JAN 2018

Tilton, Richard J 22 JAN 2018

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

Page 1 of 1EDL Version 11Generated by PRPS using Jasper Reports on 04 Jun 2019

06 FEB 2018

1377012321960ES

B-1 AIRCRAFT

L325C2011-XXI

L 43999 L0000024 W S FINISH SPECIFICATION Tilton, Richard J 06 FEB 2018

Tilton, Richard J 06 FEB 2018

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

1377012340719ES

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

REVISION: 12 *HISTORY*

1377012340821ES

DELAY ELEMENT,CARTR

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

Page 1 of 1EDL Version 12Generated by PRPS using Jasper Reports on 17 Jul 2019

29 JAN 2018

1377012340822ES

B-1B

L325C2011-II

L 43999 L0000024 W S FINISH SPECIFICATION Williams, Mark S 29 JAN 2018

WITH EO L615558

Williams, Mark S 29 JAN 2018

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

24 JAN 2018

1377012344044ES

L325C2011-XXIII

L 43999 L0000024 W S FINISH SPECIFICATION Tilton, Richard J 24 JAN 2018

Tilton, Richard J 24 JAN 2018

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

13 FEB 2018

1377012346208ES

B-1

L325C2011-XX2

L 43999 L0000024 W S FINISH SPECIFICATION Williams, Mark S 13 FEB 2018

Williams, Mark S 13 FEB 2018

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

29 JAN 2018

REVISION: 10 *HISTORY*

1377013565592ES

L325C2011-II

L 43999 L0000024 W S FINISH SPECIFICATION Williams, Mark S 29 JAN 2018

WITH EO L615558

Williams, Mark S 29 JAN 2018

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

Page 1 of 1EDL Version 10Generated by PRPS using Jasper Reports on 04 Jun 2019

1377013565593ES

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

Page 1 of 1EDL Version 11Generated by PRPS using Jasper Reports on 17 Jul 2019

13 FEB 2018

1377013568730ES

B-1

L 43999 L0000024 W S FINISH SPECIFICATION Williams, Mark S 13 FEB 2018

Williams, Mark S 13 FEB 2018

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

1377013568731ES

L325C2011-XXI

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

16 MAY 2017

REVISION: 12 *HISTORY*

1377013568732ES

L 43999 L325C2011 C S ORDNANCE TIME DELAY

ASSEMBLIES

L 43999 L0000024 W S FINISH DOCUMENT B-1B Tilton, Richard J 16 MAY 2017

Tilton, Richard J 16 MAY 2017

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

Page 1 of 1EDL Version 12Generated by PRPS using Jasper Reports on 04 Jun 2019

24 JAN 2018

1377013568733ES

L325C2011-XXIII

L 43999 L0000024 W S FINISH SPECIFICATION Tilton, Richard J 24 JAN 2018

Tilton, Richard J 24 JAN 2018

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

22 JAN 2018

1377013568734ES

L325C2011-VI

L 43999 L0000024 W S FINISH SPECIFICATION Tilton, Richard J 22 JAN 2018

Tilton, Richard J 22 JAN 2018

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

1377013568735ES

RELEASE OF THIS DATA TO A FOREIGN OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

21-50063 EDLs.pdf

EDL_011676621

EDL_012203746

21-50066 EDLs.pdf

EDL 012297600

EDL 012321677

EDL 012321960

EDL 012340719

EDL 012340821

EDL 012340822

EDL 012344044

EDL 012346208

EDL 013565592

EDL 013565593

EDL 013568730

EDL 013568731

EDL 013568732

EDL 013568733

EDL 013568734

EDL 013568735

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO. B. EXHIBIT C. CATEGORY:

TDP TM OTHER MISC

D. SYSTEM/ITEM

1377012297600ES*

E. CONTRACT/PR NO.

FD2020-21-50066/50063

F. CONTRACTOR

1. DATA ITEM NO.

A001

2. TITLE OF DATA ITEM

Ammunition Data Card (ADC)

3. SUBTITLE

4. AUTHORITY (Data Acquisition Document No.)

DI-MISC-80043B

5. CONTRACT REFERENCE

Airmunitions Specification

6. REQUIRING OFFICE

AFLCMC/EBHJ

7. DD 250 REQ

9. DIST STATEMENT

REQUIRED

10. FREQUENCY

ASREQ

12. DATE OF FIRST SUBMISSION

BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

11. AS OF DATE

N/A

13. DATE OF SUBSEQUENT

SUBMISSION

Draft

Final

Reg Repro

16. REMARKS

BLK 7: The electronic receiving report shall be annotated with the Lot Number, National Stock Number and Nomenclature. The electronic receiving report shall also be annotated to reflect if additional submittals are to be furnished or if this is the final submittal of data. The electronic receiving report shall be used only for this data item; do not combine other data item submittals with this requirement. Electronic receiving report required via internet Wide Area Work Flow (WAWF) at: https://wawf.eb.mil.

BLK 9: DISTRIBUTION STATEMENT B. Distribution authorized to U.S.

Government agencies only, (Administrative/Operational Use) (Date of Contract Award). Other requests for this document shall be referred to AFLCMC/EBHJ.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C, App. 2401 et seq.), as amended. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25.

DESTRUCTION NOTICE - Destroy by any method that will prevent disclosure of contents or reconstruction of the document.

BLK 10,12,13: Submit after successful Lot Acceptance Test and prior to delivery of each production lot.

BLK 14: A sample ADC or "draft" will be generated and submitted for each part number/NSN produced under this contract using the Worldwide Ammunition-data Repository Program (WARP) system to ensure general format and content is acceptable prior to final ADC submittals.

Sufficient hard copies of final version ADCs shall be generated for each individual production lot from the Worldwide Ammunition-data Repository Program (WARP) such that at least one hard copy per production lot shall be provided with each individual CLIN shipment/destination. An electronic copy for each production lot shall be submitted/uploaded with the electronic receiving report through WAWF to AFLCMC/EBHJ using DoDAAC FA8213.

*1377013568732ES, 1377012321677ES, 1377013568734ES,

1377012321960ES, 1377013568731ES, 1377012340719ES,

1377013568735ES, 1377012340821ES, 1377013565593ES,

1377012340822ES, 1377013565592ES, 1377012344044ES,

1377013568733ES, 1377012346208ES, 1377013568730ES,

1377012203746ES, 1377011676621ES.

FOB DESTINATION

EBH 20-170-003

WAWF 0 1 0

DoDAAC, FA8213

Included with item(s) shipped

Sample ADC via

WARP sys only

15. TOTAL 0 1 0

G. PREPARED BY

mccurdy.terry.d.1075978215

H. DATE

2020/06/19

I. APPROVED BY

hargrove.eric.v.1167016843

J. DATE

18. ESTIMATED

TOTAL PRICE

DD FORM 1423-1, FEB 2001 PREVIOUS EDITION MAY BE USED Page 1 of 2 Pages

17. PRICE GROUP

TDP TM OTHER MISC

16. REMARKS (Continued) Terry McCurdy, AFLCMC/EBHTC, 586-0535

DD FORM 1423-1, FEB 2001 Page 2 of 2 Pages

TDP TM OTHER SESS

A002

Engineering Change Proposal (ECP)

DI-SESS-80639E

BLK 4: Follow format requirements listed under paragraph 2 of Data Item Description. Data deliverable contents of notice of revision shall contain all information required by DD Form 1692.

BLK 7: The Letter of Transmittal shall be annotated to reflect if additional submittals are to be furnished or if this is the final submittal of data. The Letter of Transmittal shall be used only for this data item; do not combine other data item submittals with this requirement.

BLK 8: Within 30 days of receipt, the Government Engineer thru the Government Contracting Officer will respond with notification of approval/disapproval. If disapproved, Government Engineer response thru the Government Contracting Officer will include instruction for remediation. Notification of approval of the proposed engineering change shall be by signed contract modification.

restricted by the Arms Export Control Act (Title 22, U.S.C., Sec.

2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C, App. 2401 et seq.), as amended. Violations of these export

DESTRUCTION NOTICE--Destroy by any method that will prevent

BLK 14: Submit reports electronically via e-mail in Microsoft Office or PDF format to the following e-mail recipients listed below. Refer to contract for e-mail address of the Government Contracting Officer

(AFLCMC/EBHKB).

robert.morgan.27@us.af.mil (AFLCMC/EBHTC)

1377013568735ES, 1377012340821ES, 1377013565593ES,

1377012340822ES, 1377013565592ES, 1377012344044ES,

1377013568733ES,1377012346208ES,1377013568730ES,

AFLCMC/EBHJ 1 1 0

AFLCMC/EBHTC 1 1 0

AFLCMC/EBHKB 1 1 0

DCMA/QAR 1 1 0

DCMA/ACO 1 1 0

15. TOTAL 5 5 0

A003

Notice of Revision (NOR)

DI-SESS-80642E

BLK 4: Follow format requirements listed under paragraph 2 of Data Item Description. Data deliverable contents of Notice of Revision shall contain all information required by DD Form 1695.

submittal of data. The Letter of Transmittal shall be used only for

2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C, App. 2401 et seq.), as amended. Violations of these export

1377013568735ES, 1377012340821ES, 1377013565593ES,

1377012340822ES, 1377013565592ES, 1377012344044ES,

AFLCMC/EBHEC 1 1 0

A004

Request for Variance (RFV)

DI-SESS-80640E

BLK 4: Follow format requirements listed under paragraph 2 of Data Item Description. Data deliverable contents of Request for Variance shall contain all information required by DD Form 1694.

submittal of data. The Letter of Transmittal shall be used only for

BLK 8: Government Engineer will perform review of the RFV. Within 30 days of receipt, the Government Engineer thru the Government Contracting Officer will respond with notification of approval/disapproval. If disapproved, Government Engineer response thru the Government Contracting Officer will include instruction for remediation. Notification of approval shall be signed contract modification (AFLCMC/EBHKB).

2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C, App. 2401 et seq.), as amended. Violation of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25.

1377013568735ES, 1377012340821ES, 1377013565593ES,

1377012340822ES, 1377013565592ES, 1377012344044ES,

AFLCMC/EBHTC 1 1 0

TDP TM OTHER QCIC

A005

Lot Acceptance Test Plan

DI-QCIC-80553A

BLK16

BLK 4: Contractor format required.

BLK 7: The electronic receiving report shall be annotated with the Lot Number, National Stock Number and Nomenclature. Electronic receiving report required via internet Wide Area Work Flow (WAWF) at:

https://wawf.eb.mil. The electronic receiving report shall be used only for this data item, do not combine other data item submittals with this requirement.

BLK 8: Comments/approval/disapproval will be submitted within 30 working days of receipt by AFLCMC/EBHJ.

Government agencies (Administrative/Operational Use) (Date of restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C, App. 2401 et seq.), as amended. Violations of these export

BLK 10,11, 12, 13: The contractor shall provide a Acceptance Test Plan after contract award and at least 90 days prior to Lot Acceptance Testing allowing for 30 day approval time. No changes to previously approved government Acceptance Test Plans shall be made without prior notification of AFLCMC/EBHJ. Engineering approval in accordance with Airmunitions Specification.

BLK 14: Report shall be in Microsoft Office software or PDF format.

Submit through WAWF, DoDAAC, FA8213.

1377013568735ES, 1377012340821ES, 1377013565593ES,

1377012340822ES, 1377013565592ES, 1377012344044ES,

DoDAAC,FA8213

TDP TM OTHER QCIC

TDP TM OTHER NDTI

A006

Test/Inspection Report

Lot Acceptance Test

DI-NDTI-80809B

BLK 4: Contractor's format is acceptable.

Lot Number, National Stock Number and Nomenclature. Electronic receiving report required via internet Wide Area Work Flow (WAWF) at:

https://wawf.eb.mil. The electronic receiving report shall be used only for this data item; do not combine other data item submittals

Government agencies only (Administrative/Operational Use) (Date of

2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C, App. 2401 et seq.), as amended. Violations of these export

BLK 10,12,13: Submit within 30 calendar days after completion of each Lot Acceptance Test.

BLK 14: Test plan shall be in Microsoft Office software or PDF format. Submit through WAWF, DoDAAC, FA8213.

1377013568735ES, 1377012340821ES, 1377013565593ES,

1377012340822ES, 1377013565592ES, 1377012344044ES,

DoDAAC, FA8213

DD FORM 1423-1, FEB 2001 PREVIOUS EDITION MAY BE USED Page 1 of 1 Pages

A007

Failure Summary & Analysis Report

DI-SESS-80255B

BLK 4: Contractor's format required for both the Preliminary and Final report.

submittal of data. The Letter of Transmittal shall be used only for requirement calendar days after receipt by AFLCMC/EBHJ.

2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C, App. 2401 et seq.), as amended. Violations of these export

BLK 14: Report shall be in Microsoft Office software or PDF format.

Submit via e-mail to cognizant Hill AFB Contracting Officer.

1377013568735ES, 1377012340821ES, 1377013565593ES,

1377012340822ES, 1377013565592ES, 1377012344044ES,

Contr. Officer 0 1 0

Hill AFB, UT

D. SYSTEM/ITEM E. CONTRACT/PR NO.

FD2020-21-50066A/50063

B001

TEST REPORT

DI-NDTI-80603A

Airmunition Specification

1TIME

BLK 4: Follow format per DID. Incorporate the following applicable requirements:

a. Dimension and tolerances specified on the manufacturing data shall be listedin one column with the actual corresponding reading obtained from inspection of the part, listed in another column.

b. Material utilized in the manufacture of "First Article" item shall be identified and certified as conforming to applicable data requirements.

c. Certification that identification markings, i.e., part number per MIL-STD-130 and Federal Supply manufacturer (FSCM) per H4-1 Cataloging Handbook (if applicable) have been complied with.

d. The test report will be certified by the responsible DCMA/QAR.

(Authorization for any deviations from the requirements specified by themanufacturing data must be obtained from the procuring agency prior to inclusion in the test report).

Lot Number, National Stock Number, and Nomenclature. Electronic receiving report required via internet Wide Area Work Flow (WAWF) at:

https://wawf.eb.mil.

Government agencies (Administrative/Operational Use)(Date of Contract Award). Other requests for this document shall be referred to

AFLCMC/EBHJ.

2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C, App. 2401 et seq.), as amended. Violations of these export

BLK 12: Submit no later than 30 calendar days after completion of First Article Acceptance Testing. Submit through Worldwide Ammunition-data Repository Program (WARP) and WAWF under DoDAAC

FA8213.

1377013568735ES, 1377012340821ES, 1377013565593ES,

1377012340822ES, 1377013565592ES, 1377012344044ES,

DoDACC, FA8213

2020/06/30

EBH 20-182-004

B002

First Article Qualification Test Plan and Procedures

DI-NDTI-81307A

BLK 4: Contractor's format required.

Lot Number, National Stock Number, and Nomenclature. Electronic receiving report required via internet Wide Area Work Flow (WAWF) at:

https://wawf.eb.mil. The electronic receiving report shall be used only for this data item; do not combine other data item submittals working days of receipt by AFLCMC/EBHJ.

Government agencies (Administrative/Operational Use) (Date of

2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C, App. 2401 et seq.), as amended. Violations of these export

BLK 10, 11, 12, 13: The contractor shall provide a Qualification Test Plan/Procedures 30 days after contract award, allowing for 30 days approval time. No changes to previously approved government Test Plans shall be made without prior approval from AFLCMC/EBHJ Engineering approval, IAW Airmunitions Specification.

BLK 14: Submit reports electronically in Microsoft Office software or PDF format to addressee listed in block 16.

1377013568735ES, 1377012340821ES, 1377013565593ES,

1377012340822ES, 1377013565592ES, 1377012344044ES,

EBH 20-182-004

15. TOTAL 0 0 0

CDRLs_21-50066

CDRLs_21-50066A

REPSHIP Data Requirements for Individual Shipments of Hazardous Material (HAZMAT) and Inert Component Parts - Continental United States (CONUS) to CONUS, CONUS to Overseas or From All

Overseas Locations FROM: Shipping Activity To: Domestic Customer or Transshipping Activity Clearance Authority (Ocean) or Customer Service

Branch (CSB) (Air) or CONUS Sea Terminal

INFO: GACP TRANSPORTATION, HILL AFB UT - (AFLCMC / EBHMB)

email: ooalc.gacp.transportation@us.af.mil or FAX (801) 777-1089.

INFO: Sponsoring Service Accountable Supply Activity Ultimate Consignee/ Final Destination

SUBJ: Report of Shipment (REPSHIP)

1. Shipment Date written as a three-digit day of the year (Julian)

2. Estimated Time of Arrival (ETA) written as a three-digit day of the year (Julian) (Observe Standard Transit

Time (STT), if CONUS Truck Shipment and no Required Delivery Date (RDD) identified)

3. Required Delivery Date (RDD) or Delivery Date (DD), if specified

4. Carrier

5. Bill of Lading (BL) Number (Notes 1, 2, 3, 4)

6. Military Traffic Expediting-Greater Security (MTX-GS) Service Number (Notes 1, 2, 3)

7. Air Release Number (Notes 1, 2, 3) or for Surface Shipments, Export Traffic Release (ETR) Number and

Vessel Name and/or Voyage Document Number

8. Shipment (Cargo) Name (Example: Bombs)

9. Container and Seal Number (if applicable):

a. Container Transportation Control Number (TCN)

b. Total Weight of Contents

c. Rounds, Pieces, Weight, Cube, Condition code, and Lot Numbers (Note 4)

10. Security Risk Category (SRC), (E.G., Security Risk Category I, II, III, IV, Unclassified, Confidential, Secret, None)

11. Controlled Item Inventory Code (CIIC)

12. Total Net Explosive Weight (NEW)

13. Hazard Classification (s)

14. Department of Defense Identification Code / Navy Ammunition Logistic Code (DODIC/NALC). (Note 4).

15. Name, address, and phone number of person responsible for information contained in REPSHIP

NOTES:

1. When the conveyance contains more than one shipment unit, repeat the data elements in separately lettered paragraphs for each shipment unit.

2. Cargo for more than one vessel or flight, but shipped to Port of Embarkation (POE) in a single conveyance, is included in a single REPSHIP. When cargo for a single vessel is moved to the Seaport of Embarkation (SPOE) in more than one conveyance, repeat all the data elements as above in separate numbered paragraphs for each conveyance or REPSHIP.

3. A separate REPSHIP is used for each mode of shipment to the POE.

4. Lot number, DODIC and NALC are not mandatory fields. If available, they may be provided in the electronic

RESHIP or in the template above. If a CBL is used, the lot number and ammunition condition code should be included in the remarks section. Weapons must be identified on the CBL by each serial number contained within the shipment.

5. DODIC and NALC are codes used specifically for logistic administration and control of ammunition.

Attachment 1 mailto:ooalc.gacp.transportation@us.af.mil

1. Shipment Date written as a three-digit day of the year (Julian)

2. Estimated Time of Arrival (ETA) written as a three-digit day of the year (Julian) (Observe Standard Transit Time (STT), if CONUS Truck Shipment and no Required Delivery Date (RDD) identified)

3. Required Delivery Date (RDD) or Delivery Date (DD), if specified

4. Carrier

5. Bill of Lading (BL) Number (Notes 1, 2, 3, 4)

6. Military Traffic Expediting-Greater Security (MTX-GS) Service Number (Notes 1, 2, 3)

7. Air Release Number (Notes 1, 2, 3) or for Surface Shipments, Export Traffic Release (ETR) Number and Vessel Name and/or Voyage Document Number ...

8. Shipment (Cargo) Name (Example: Bombs)

9. Container and Seal Number (if applicable):

a. Container Transportation Control Number (TCN)

b. Total Weight of Contents

c. Rounds, Pieces, Weight, Cube, Condition code, and Lot Numbers (Note 4)

10. Security Risk Category (SRC), (E.G., Security Risk Category I, II, III, IV, Unclassified, Confidential, Secret, None)

11. Controlled Item Inventory Code (CIIC)

12. Total Net Explosive Weight (NEW)

13. Hazard Classification (s)

15. Name, address, and phone number of person responsible for information contained in REPSHIP

NOTES:

CAD/PAD Item Marking Instruction, V 1.5

CAD/PAD Item Marking Instruction

Prepared By CAD/PAD Joint Program Office

NSWC IHEODTD and AFLCMC/EBHJ

Version 1.5 Dated 01 May 2019

Purpose

Table of Contents

2. Scope Page 5

3. Marking Requirements Page 6

4. Placement of UID Markings Page 8

5. Items delivered in kit format Page 9

6. Waivers Page 9

References

NOTE: Use latest revision of all reference documents.

1. MIL-STD-130 Department of Defense Standard Practice Identification Marking of U.S.

Military Property

2. MIL- STD-1168 (current revision) Ammunition Lot Numbering and Ammunition Data Card

(Note section 3.1 for new lot assignment for “remanufactured CAD/PAD Components”)

3. ISO/IEC 16022 Information technology - Automatic identification and data capture techniques - Data Matrix bar code symbology specification

4. ISO/IEC 15434 Information technology - Automatic identification and data capture techniques - Syntax for high capacity ADC media

5. ISO/IEC 15418 Information technology - Automatic identification and data capture techniques - GS1 Application Identifiers and ASC MH10 Data Identifiers and maintenance

6. UNDER SECRETARY OF DEFENSE FOR ACQUISITION POLICY AND

TECHNOLOGY Department of Defense Guide to Uniquely Identifying Items version 1.6 (this document is available on line at http://www.acq.osd.mil/dpap/pdi/uid/index.html or from Defense Procurement & Acquisition Policy, 3060 Defense Pentagon, Room 3E1044, Washington, DC 20301-3060)

7. DEFENSE FEDERAL ACQUISITION REGULATION SUPPLEMENT 252.211-7003

Item Identification and Valuation (Copies of this document are available on line at http://farsite.hill.af.mil/ or from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954)

8. AFSCM 21-556 Vol. 2 Julian Date format

9. ANS MH10.8.2 - 2006 Data Application Identifier Standard

10. –ISO 28219 Labeling and Direct Product Marking with Linear Bar Code and Two- Dimensional Symbols http://www.acq.osd.mil/dpap/pdi/uid/index.html http://farsite.hill.af.mil/ http://farsite.hill.af.mil/

Figures

1. Determining IUID requirement

2. Sample UID Data Stream

3. Sample CAD/PAD Data Plate/Label

4. Sample of Etched Data

5. Sample CAD/PAD Small Item Data Plate/Label

1. Purpose.

The Under Secretary of Defense has implemented policy requiring DoD components meeting the requirements identified in Figure 1 to be marked with Item Unique Identifiers (IUID). Cartridge Actuated Devices and Propellant Actuated Devices (CAD/PAD) items, regardless of dollar value, are typically serially managed in aircraft maintenance data systems and therefore are applicable to the IUID requirement.

Additionally, the Air Force Aircrew Escape System Executive Working Group (AESEWG) and the egress system maintenance community has requested that CAD/PAD items be marked with Data Matrix ECC 200 on item data plates or items to enhance accuracy of aircraft maintenance data.

In accordance with MIL-STD-130, this marking instruction identifies marking requirements that meet the above objectives by tailoring Unique Identification (UID) requirements to include aircraft maintenance data requirements for both free text Human Readable Information (HRI) and Machine Readable Information (MRI), which are both mandated requirements for CAD/PAD items.

Figure 1. Determining UID Requirement

2. SCOPE.

This instruction identifies marking requirements applicable to suppliers/manufacturers of CAD/PAD components. It is applicable to both production of new CAD/PAD components and remanufacture of service returned, over-aged components. It identifies marking methods applicable to the various sizes and shapes of CAD/PAD components.

As of this writing, guidance regarding mandated transfer of data to the IUID registry can be found at “http://www.acq.osd.mil/dpap/pdi/uid/index.html”. Go to Training and Communication link, select IUID Toolkit (www.IUIDtoolkit.com), and select “Defense Suppliers”, then under “Submit”, select subsection “Registration of IUID Data11”, under Support Tools select “Data Submission”.

http://www.iuidtoolkit.com/

3. Marking Requirements.

Both Human Readable Information (HRI) and Machine Readable Information (MRI) are required (see section 4). In accordance with the Defense Federal Acquisition Regulation Supplement (DFARS), DoD has mandated the use of Data Matrix ECC 200 as the standard format for UID MRI markings. Guidance for the construct and application of Data Matrix markings is contained in MIL-STD-130 and the DoD UID Guide located at http://www.acq.osd.mil/dpap/pdi/uid/index.html, select Guides link.

3. 1. HRI Marking Requirements. The following HRI data is required (as a minimum):

- Item Nomenclature; Per applicable manufacturer drawing

- Manufacturer’s Commercial and Government Entity (CAGE); Five (5) alpha/numeric characters.

- Item Lot Number; Lot numbers shall be assigned IAW MIL-STD-1168 (current revision), unless otherwise directed. A new lot number and serial number shall also be assigned for “remanufactured” CAD/PAD components as opposed to adding a suffix to the original lot number for a “rework, overhaul or renovation” effort.

NOTE: The requirement for unique lot number has been deleted.

DOM is NOT required if the lot number contains the DOM as identified in MIL-STD-1168

- Item Serial Number; Serial number shall be up to eight (8) numeric characters.

The serial numbers shall be sequentially assigned and shall not be repeated until serial number 99,999,999 has been reached.

- Item manufacturer’s Part Number

NOTE: The weapon system Specification Number does not meet this

- Optional markings: Additional markings (such as manufacturer’s name, logo, contract number) are acceptable, provided that space is available on the item/data label. Date of Manufacture (DOM); DOM shall be MM/YYYY and be the same date that is coded into the lot number.

NOTE: Markings and/or attachments shall make no reference to item installation requirements/procedures or shelf/service lives

S S S S S o

3.2. MRI Data Construct.

Data Matrix ECC200 markings shall be developed based on UID Data Construct #2 using Data Identifiers (DIs) in accordance with MIL-STD-130 and the DoD UID Guide (see Figure 2). To facilitate durability throughout the scanning life cycle, the largest symbol size, including quiet zone, shall be fitted within the available marking real estate. The symbol’s internal module (cell) sizes shall be no smaller than 0.0075 inch (0.19 mm) and no larger than 0.025 inch (0.64 mm). Marks shall contain only the data elements identified below:

NOTE: The actual UII will be comprised of CAGE, Part Number, and Serial Number data. The parenthesis surrounding the Data Identifiers are NOT encoded in the 2D symbol

(17V) Manufacturer’s Commercial and Government Entity (CAGE) code, 5 alpha/numeric characters

- (1P) Manufacturer’s Item Part Number, 18 alpha/numeric characters maximum

NOTE: The weapon system specification numbers do not meet this

- (S) Item Serial Number, IAW HRI requirement, up to eight (8) numeric characters

- (30T) Item production Lot Number, IAW HRI requirement, 15 alpha/numeric characters maximum

NOTE: The data identifier for Lot Number has been changed from 1T to 30T

- (4D) Date of Manufacture (DOM), in Julian Date format, five (5) numeric characters:

Example: 08151 = 31 May 2008

The first two positions are the last two digits of the year, the last three positions are the Julian Date (001 through 366)

[)> R 06 G 17V 12345 G 1P 123456789-ABCDEFGH G S 12345678 G 30T ABC06D123-001 G 4D 08151 R E

Figure 2. Sample UID Data Stream

S S T

4. Placement of UID Marking. CAD/PAD items vary considerably in size and shape. A large percentage of these items are currently marked with HRI printed on data plates or labels permanently affixed to the item. The preferred method for incorporating the UID required MRI is to include it on the current data plate/label and, wherever possible, the supplier is to incorporate this concept. The following identifies known variations in marking and preferred MRI incorporation methods.

Note: Unless specifically identified as a requirement in the procurement contract, subcomponents of the End Item Assembly shall not be UID marked.

4.1. CAD/PAD Items Currently Marked with Data Plates, Labels, or Flag-Tags. The data plates/labels for these items shall be modified/arranged to allow space for the MRI per paragraph 3.2. Marking shall comply with MIL-STD-130 and the DoD UID Guide (see figure 3).

Figure 3. Sample Data Plate/Label

4.2. CAD/PAD Items Currently Marked With Ink or Laser Etching Directly on the Item.

Item marking shall be modified/arranged to allow space for the incorporation of ink or laser etched MRI per paragraph 3.2. Marking shall comply with MIL-STD-130 and the DoD UID Guide (see figure 4).

CAD/PAD Builder Inc.

Acft Explosive Component Noun

CAGE: 12345

P/N: 123456789-1234

Ser No: 0001 Lot No: ABC08D001-001

DOM: 04/2008

Figure 4. Sample of Etched Data

CAD/PAD Builder Inc.

Acft Explosive Component Noun

CAGE: 12345

P/N: 123456789-1234 Ser No: 0001

4.3. CAD/PAD Items Considered to be Too Small for HRI and MRI. These items shall be physically marked using currently approved methods for HRI. A self-adhesive label shall be supplied in the item inner packaging that includes the minimum HRI (per paragraph 3.1) and the MRI Data Matrix marking (per paragraph 3.2). The label shall be as small as possible (meeting MIL-STD-130 requirements for HRI) and will include only the minimum required data (see figure 5).

Figure 5. Sample Small Item Data Plate/Label

Note: This will allow the maintainer to scan the MRI from the label and the ability to affix it to the next higher assembly.

5. Kit Marking Requirements. Individual components procured and delivered in a “kit” or “ship-set” format shall each be marked with HRI and MRI as identified in sections 3 and 4.

The kit containers shall also be marked with HRI and MRI per sections 3 and 4.

Note: Individual components supplied in kits or ship-sets require unique item identifiers. Their markings shall not reflect those identifying the kit or ship-set.

5.1 Only the “kit “or “ship-set” will require data submission into the UID Registry. Data submission for individual components in a kit is not required, as these components were not individually priced as line items when placed on contract.

Note: To meet UID requirements, each kit will be assigned an individual serial number. Kits that are comprised of multiple containers will all be marked with the same serial number.

5.2 “Kits” or “ship sets” will typically be assigned lot numbers coinciding with the oldest individual component in the kit.

6. JSF F-35 Instructions. The marking instructions for F-35 components, labels, and packaging, shall be as outlined in this document. Additionally, contractors are required to submit an Electronic Equipment Logbook (EEL) for all serial numbers delivered to the Government. When submitting EELs, the lot number is limited to 10 characters and shall only include the year of production, month of production, interfix number, and sequence number with no dashes. Use of these nine characters will allow for an optional lot suffix as

Acft Explosive Item Noun

CAGE: 12345

P/N: 123456789-1234 Ser No: 0001 deemed necessary by procuring agency. The lot number identified on the Ammo Data Card (ADC) shall match the lot number used on the components and shall be generated

IAW MIL-STD-1168.

7. Waivers. Waivers to the UID requirement are not allowed. Requests for waivers to marking methods outlined in this instruction may be considered. Submit requests through appropriate contracting channels.

CAD/PAD Item

Dated 01 May 2019

Figures

1. Purpose.

2. SCOPE.

3. Marking Requirements.

Example: 08151 = 31 May 2008

Figure 2. Sample UID Data Stream

Figure 3. Sample Data Plate/Label

Figure 4. Sample of Etched Data

Figure 5. Sample Small Item Data Plate/Label

NOTE: THE ABOVE POP MARKINGS

ARE FOR DOD USE ONLY.

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO DEPARTMENT OF DEFENSE AND U.S. DOD CONTRACTORS ONLY, ADMINISTRATIVE OR OPERATIONAL USE, 04 APRIL 2018. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO 406 SCMS/GULAA, (PACKAGING DIVISION), HILL AFB, UTAH 84056.

DESTRUCTION NOTICE: FOLLOW THE PROCEDURES IN DOD 5220.22-M, NATIONAL INDUSTRIAL SECURITY PROGRAM OPERATING MANUAL (NISPOM), SECTION 5-705, OR DOD 5200.1-R, INFORMATION SECURITY PROGRAM, CHAPTER VI. FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

AutoCAD SHX Text

2169 MOD

FORM

MARCH 87

COMPUTER GENERATED

SPI NO. F01-167-6621

SPECIAL MARKINGS:

A) SPI NO. F01-167-6621

B) PROPER SHIPPING NAME:

PACKAGING WAS MANUFACTURED.

C) UN POP MARKING:

**THE LAST TWO DIGITS OF THE YEAR DURING WHICH THE

CLOSURE:

LEVEL B:

LEVEL A:

USA/DOD/AF70

4G/Y25/S/** u

PART OR DRAWING NO.

SPECIAL PACKAGING INSTRUCTION

ITEM NOMENCLATURE

MILITARY PRESERVATION IAW MIL-STD-2073

PRESERVATIVE: N/A

CLEANING & DRYING: IAW MIL-STD-2073

MARKING IAW MIL-STD-129

UNSERVICEABLE METHOD: 41

QUP

ICQ

MULTIPLE PART NUMBERS

ORIGINAL

INITIATOR, PROPELLANT ACTUATED

14233

DATE

AUTH.

CHK.

1377-01-167-6621 ES

NATIONAL STOCK NO.

CURRENT

REV

P.S.

ILL.

98747

CODE ID

DODPOPHM/USA/DOD/AF70/TR14001

SHEET 1 OF 5

SPI NO. (TPO)

SEE NOTICE 1

LEVEL A LEVEL B

LENGTH WIDTH DEPTH

VARIES

10 3/8

AS SPECIFIED BELOW AND BILL OF MATERIALS

SPEC STYLE TYPE CL VRTY GR TR

REVISIONS

DESCRIPTION

CNTR I.D.

LTR

ITEM DIM

ITEM WT.

CNTR O.D.

GROSS CU FT

GROSS WT LBS

DESIGN FRAGILITY G

ASTM D6251

ASTM D5118

LEVEL

PACKING

16 3/4

1.043

D. NAY J. BURLEIGH J. HARMON N. CORONADO

F01-167-6621

D) REUSABLE CONTAINER & DUNNAGE DO NOT DESTROY.

RSC

III

V3c

IAW: ASTM D1974 SEALING METHOD C

IAW: ASTM D6251

MARK THE SPI NUMBER ON THE IDENTIFICATION SIDE OF CONTAINER.

SERVICEABLE METHOD: 41

CARTRIDGES, POWER DEVICE

UN0276

ADD DISTRIBUTION STATEMENT, DESTRUCTION NOTICE AND CHANGED BOM

18094

REQD

P/N

QTY

SIZE: (INCHES UNLESS SPECIFIED) TOLERANCES ON FRAC. ± , 18, DECIMAL ± .10, ANGLES ± 1°

NOMENCLATURE OR

MATERIAL

A/R A/R 1 A/R

TAPE, PACKAGING WRAP BARRIER BAG CUSHIONING

3 X AS REQUIRED AS REQUIRED AS REQUIRED AS REQUIRED

ASTM D5486 TYPE I OR V MIL-PRF-81705 TYPE I, CLASS 1 MIL-DTL-117 TYPE I, CLASS F, STYLE 1 A-A-1898 GRADE II, CLASS B

-4 -3 -2 -1

2169C MOD

SHEET 2 OF 5

MUNITION NOTICES

NOTICE 1 : FOR LEVEL A PACKING REQUIREMENTS: THE LEVEL B PACKS SHALL BE OVERBOXED IN A LEVEL A SPECIFIED

CONTAINER SHOWN ON PAGE 1 UNDER PACKAGING LEVEL A. MARK THE OUTSIDE OF THE OVERBOX "OVERPACK." THE

SIZE AND WEIGHT OF THE OVERBOX WILL VARY DEPENDING ON THE NUMBER OF ITEMS BEING SHIPPED. USE FILLER

PAD OF ASTM-D4727, CF, DOM, GR 275 (OR EQUAL) TO ENSURE A TIGHT FIT IN THE OVERBOX.

NOTICE 2: ASSETS PACKAGED IN ACCORDANCE WITH PREVIOUS EDITIONS OF THIS SPI DO NOT REQUIRE REPACKAGING

IF THE INTEGRITY OF THE SPI IS MAINTAINED.

NOTICE 3: SEE SPIRES FOR A COMPLETE LISTING OF NSN's ASSIGNED TO THIS SPI.

NOTICE 4: THIS SPI IS NOT AUTHORIZED FOR USE WITHOUT PROPER HAZARD CLASSIFICATION. UNLESS A FINAL

HAZARD CLASSIFICATION HAS BEEN ISSUED, A COPY OF THE VALID INTERIM HAZARD CLASSIFICATION LETTER ALONG

WITH DOT SP 15448 MUST ACCOMPANY EACH SHIPMENT.

NOTES

1. MAY PLACE UP TO 10 BAGGED ITEMS IN SHIPPING CONTAINER USING REF.-1 TO ENSURE THAT ITEMS DO NOT TOUCH

EACH OTHER OR SIDES OF OUTER CONTAINER.

2. WRAP ITEM USING REF.-3, PLACE IN BAG REF.-2 REMOVE AIR AND SEAL.

INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES

REVISION OF ISPM NO. 15

REVISION OF WOOD PACKAGING MATERIAL FOR INTERNATIONAL TRADE

THE FOLLOWING STATEMENT IS IN COMPLIANCE WITH THE UNITED NATIONS-IMPLEMENTED RESTRICTIONS ON WOOD

PACKAGING MATERIAL (WPM). THIS REQUIREMENT IS SPECIFICALLY CONCERNED WITH INVASIVE SPECIES SUCH AS THE

PINEWOOD NEMATODE. WPM IS DEFINED AS WOOD PALLETS, SKIDS, LOAD BOARDS, PALLET COLLARS, WOODEN BOXES, REELS, DUNNAGE, CRATES, FRAMES, AND CLEATS. THE STATEMENT BELOW CITES THE REQUIREMENTS IN DETAIL AND

COVERS LUMBER FOR BUILDING CONTAINERS AND PALLETS USED FOR DELIVERIES, RESULTING IN SHIPMENTS WORLDWIDE

(DIRECT, OR THROUGH AIR LOGISTICS CENTERS (ALC), CONTAINER CONSOLIDATION POINTS (CCP), OR OTHER BASES).

WOODEN LUMBER, WOODEN PALLET AND PACKAGING/CONTAINER STATEMENT:

ALL WOODEN LUMBER, WOODEN PALLETS, AND WOODEN CONTAINERS PRODUCED ENTIRELY OR IN PART OF WOOD

PACKAGING MATERIAL (WPM) SHALL BE CONSTRUCTED FROM DEBARKED WOOD IN ADDITION TO THE APPLICATION OF

HEAT-TREATED (HT) MATERIAL (HT TO 56 DEGREES CENTIGRADE OR 133 DEGREES FAHRENHEIT FOR 30 MINUTES).

CERTIFICATION/MARKING IS REQUIRED BY AN ACCREDITED AGENCY RECOGNIZED BY THE AMERICAN LUMBER STANDARDS

COMMITTEE (ALSC). FOR REFERENCE DOCUMENTATION, SEE LATEST REVISION OF…

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated Dec 28, 2020.