SSMA_Product_Technical_Information.pdf

Administrator Text Box $5.00

PRODUCT IDENTIFICATION

All SSMA products have a four part identifi cation code which identifi es the size (both depth and fl ange width), style, and material thickness of each member.

EXAMPLE:

MATERIAL THICKNESS:

(Example: 0.054 in. = 54 mils;

1 mil = 1⁄1000 in.)

Material thickness is the minimum base metal thickness in mils. Minimum base metal thickness represents 95% of the design thickness.

FLANGE WIDTH:

(Example: 1 5⁄8" = 1.625" 162 1⁄100 inches) All fl ange widths are taken in 1⁄100 inches.

MEMBER DEPTH:

(Example: 6" = 600 1⁄100 inches) All member depths are taken in 1⁄100 inches.

For all “T” sections member depth is the inside to inside dimension.

STYLE:

(Example: Stud or Joist section = S) The four alpha characters utilized by the designator system are:

S = Stud or Joist Sections* T = Track Sections U = Channel Sections F = Furring Channel Sections

C-STUD / JOIST TRACK CHANNEL FURRING CHANNEL

S-SECTIONS T-SECTIONS U-SECTIONS F-SECTIONS

Note: For those sections where two different yield strengths (33 ksi and 50 ksi) are shown, the yield strength used in the design, if greater than 33 ksi, needs to be identified on the design and ordering of steel. (i.e., 600S162-54 (50 ksi))

* For “S” members, see table on page 5 for stiffening lip length.

Copyright © 2010 by the Steel Stud Manufacturers Association

600 S 162 - 54

Complies with the 2006 International Building Code (IBC)

Product Identifi cation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inside front cover General Product Information

Introduction Code Approval Material Specifi cations Technical Assistance Thickness — Steel Components Design Stiffening Lip Length General Notes for all Tables Defi nitions of Structural Property Symbols

Section Properties Section Properties Table Notes Non-Structural (S) Stud Section Properties Structural (S) Stud Section Properties Structural (T) Track Section Properties Web Depth to Thickness Ratios

Wall Height Tables Interior Non-Structural Non-Composite Limiting Wall Heights — Curtain Wall Single-Span Limiting Wall Heights — Curtain Wall Double-Span

Combined Axial and Lateral Load Tables Combined Loading Allowable Axial Load Table Notes Allowable Axial Loads

Floor Joist Span Tables Allowable Floor Joist Span Table Notes Bridging Recommendations Allowable Floor Joist Spans

Header Load Tables Header Load Table Notes Header Allowable Uniform Loads

Web Crippling Load Tables Web Crippling Load Table Notes Web Crippling Conditions Allowable Web Crippling Loads — Single Members Allowable Web Crippling Loads — Back-to-Back Members

Ceiling Span Table Ceiling Span Table Notes Allowable Ceiling Spans — Defl ection Limit L/240 Allowable Ceiling Spans — Defl ection Limit L/360 Typical Ceiling Details

Channel Properties U-Channel Section Properties U-Channel Allowable Ceiling Spans (Hat) Furring (F) Channel Section Properties (Hat) Furring (F) Channel Allowable Ceiling Spans

Fasteners (Screws and Welds) Allowable Loads for Screw Connections Allowable Loads for Fillet Welds and Flare Groove Welds

Typical Details Cold Rolled Lateral Bracing Wall Stud Web Stiffener Flat Strap Lateral Bracing

Code Compliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover

Table of Contents

Administrator Text Box Editorial corrections & additions made 12/2010 on pages 7, 8, 9, 55, and 56. Corrections are shown in red text on light red background (similar to this note) with black sidebar in left column.

Rectangle

General Product Information Introduction

The increasing environmental concerns in the world today have caused us all to examine the way we live. These issues have affected every aspect of our lives, including the materials we use in construction. The use of cold-formed steel members as a building alternative is an intelligent choice with benefi ts to not only the environment, but also to the contractor, designer and developer.

Steel is not only a recyclable product, but also a stronger product allowing for longer clear-spans in the design process. Cold-formed steel is lighter providing ease of handling. It is a dimensionally stable product giving a “straight” wall with which to work. It doesn’t suffer fl uctuation in price, making it easier to bid a project. Quality control is stressed in all phases of the manufacturing process so the highest possible quality is delivered to the job site. The structural shapes manufactured are easily used for non-structural and structural assemblies, fl oor and ceiling joist assemblies, trusses, and panelized systems. They can be used as the main structural support system or as a supplement to heavy structural steel or concrete construction.

SSMA member manufacturers have been producing cold-formed steel framing members for many years, with each manufacturer having its own nomenclature and design values. A steel member with identical properties would be identifi ed by different names based on which manufacturer produced it. This created some confusion at all levels of the construction process.

The SSMA’s mission is to be the unifi ed voice of the steel framing manufacturing industry, by being the leader in supporting the development and maintenance of quality product standards and specifi cations, and by creating growth opportunities for cold-formed steel through research, marketing, and education.

Code Approval SSMA producer members demonstrate code compliance through their participation in the SSMA third party Code Compliance Certifi cation program, administered by Architectural Testing, Inc. (ATI). Look for products and bundles marked with the SSMA and ATI label or logo, stating “CERTIFIED CODE COMPLIANT.” In addition, SSMA maintains an Evaluation Service Report through International Code Council Evaluation Service (ICC-ES). For details on both programs, as well as listing of manufacturing facilities participating in each program, go to www.ssma.com. See back cover of this catalog for additional information.

Material Specifi cations Products manufactured by SSMA members are formed from steel with a minimum yield stress of 33 or 50 kips per square inch (KSI). Unless noted otherwise, all products covered in this catalog are engineered to meet the 2001 edition with 2004 supplement of the American Iron and Steel Institute (AISI) North American Specifi cation for the Design of Cold-Formed Steel Structural Members (2004 AISI Specifi cation) and other AISI standards referenced in section 2210 of the 2006 International Building Code (IBC). The structural properties included in this brochure have been computed based on allowable strength design. Not all products listed are available from all SSMA member companies – check local supplier or specifi c SSMA member for availability. For fastener tables, screw sizes and head diameters do not refer to specifi c fasteners which may or may not be available from SSMA members. Shear and tension data for screws was developed with the assistance of the Wei-Wen Yu Center for Cold-Formed Steel Structures (CCFSS).

Technical Assistance Professional technical assistance is available through any SSMA member to its customers. Using software developed specifi cally for the SSMA, a manufacturer’s technical representative can analyze load conditions, defl ection criteria and lateral bracing conditions not presented in this brochure. Computerized design can assist a SSMA customer with the most economical product selection for the specifi c application. Contact the SSMA manufacturer for this assistance.

Disclaimer All data, specifi cations and details contained in this publication are intended as a general guide for using SSMA members’ products. These products should not be used in design or construction without an independent evaluation by a qualifi ed engineer or architect to verify the suitability of a particular product for use in a specific application. The SSMA and its members assume no liability for failure resulting from the use or misapplication of computations, detail drawings and specifi cations contained herein. This publication contains the latest information available at the time of printing with respect to the referenced building codes and standards. The SSMA and its members reserve the right to make modifi cations and/or change materials of any of their products without prior notice or obligation. For the latest information regarding a particular manufacturer’s products contact that manufacturer. All SSMA manufacturers may not produce all of the products contained in this catalog. Please contact manufacturer to verify product availability.

General Product Information Thickness Table

1 Minimum Thickness represents 95% of the design thickness and is the minimum acceptable thickness delivered to the job site based on Section A2.4 of the 2004 AISI Specifi cation.

2 The tables in this catalog are calculated based on inside corner radii listed in this table.

General Notes for all tables

1. Where ‘AISI 2004 Specifi cation’ is referenced, it is the “North American Specifi cation for the Design of Cold-

Formed Steel Structural Members”, 2001 edition, including the 2004 Supplement, with US provisions.

2. The strength increase from cold work of forming has been incorporated for fl exural strength per AISI 2004

Specifi cation A7.2

3. The effective moment of inertia for defl ection is calculated at a stress which results in a section modulus such that the stress times the section modulus at that stress is equal to the allowable moment. AISI 2004 Specifi cation Procedure I for serviceability determination has been used.

4. Various sections may be manufactured with yield points of 33 or 50 kips per square inch (KSI). The yield point used for calculations is indicated in the tables.

5. For sections available in both 33 and 50 KSI, the specifi er must clearly indicate which yield point is required. For example: 362S162-54 (50 KSI).

6. When provided, factory punchouts will be located along the centerline of the webs of the members and will have a minimum center-to-center spacing of 24 inches. Punchouts for members > 2.5 inches deep are a maximum of 1.5 inches wide x 4 inches long. Members with depths 2.5” and smaller are maximum 3/4” wide x 4 inches long.

Defi nitions of Structural Property Symbols Gross Properties

Design Stiffening Lip Length noitceS htdiWegnalF gnineffitSngiseD )ni(htgneLpiL

521S 1 1 ⁄4 " 881.0 731S 1 3 ⁄8 " 573.0 261S 1 5 ⁄8 " 005.0 002S "2 526.0 052S 2

S300 3" 0.625 S350 3 " 1.000

1 ⁄2 " 526.0

1 ⁄2

Ix: Moment of inertia of the gross section about the X-X axis (strong axis).

Sx: Section modulus about the X-X axis (strong axis).

Rx: Radius of gyration of the gross section about the X-X axis.

Iy: Moment of inertia of the gross section about the Y-Y axis (weak axis).

Ry: Radius of gyration of the gross section about the Y-Y axis.

Effective Properties Ixe: Moment of inertia for defl ection calculations based on “Procedure 1 for Defl ection

Determination” of the 2004 AISI Specifi cation.

Sxe: Effective section modulus about the X-X axis (strong axis) Stress = Fy.

Ma: Allowable Bending Moment – Based on the effective section modulus and the allowable stress including the strength increase from cold-work of forming (AISI 7.2) where applicable.

Vag: Allowable strong axis shear away from punchout, calculated in accordance with AISI section C3.2.1.

Vanet: Allowable strong axis shear at the punchout, calculated in accordance with AISI section C3.2.2.

Torsional and Other Properties J: St. Venant Torsional Constant.

Cw: Torsional warping constant.

M: Distance from shear center to mid-plane of web.

Xo: Distance from the shear center to the centroid along the principal X-axis.

Ro: Polar radius of gyration about the centroidal principal axis.

: 1- (Xo/Ro)2

Lu: The longest weak axis (Ly) and torsional (Lt) unbraced length at which lateral torsional buckling is restrained in accordance with AISI C3.1.2.1.

Designation Thickness (mils)

Minimum Thickness1(in)

0.0179 0.0269 0.0296 0.0329 0.0428 0.0538 0.0677 0.0966 0.1180

Design Thickness1 (in)

0.0188 0.0283 0.0312 0.0346 0.0451 0.0566 0.0713 0.1017 0.1242

Design Inside Corner

Radii 2 (in)

0.0843 0.0796 0.0781 0.0764 0.0712 0.0849 0.1069 0.1525 0.1863

Reference Only Gauge No.

20 – Drywall 20 – Structural

Section Properties

Non-Structural (S) Stud Section Properties

Section Properties Table Notes

1. The centerline bend radius is based on inside corner radii shown in thickness chart on page 5.

2. Web depth for track sections is equal to the nominal height plus 2 times the design thickness plus the bend radius.

3. Hems on non-structural track sections are ignored.

4. Effective properties incorporate the strength increase from the cold work of forming as applicable per AISI A7.2.

5. Tabulated gross properties are based on the full-unreduced cross section of the studs, away from punchouts.

6. For defl ection calculations, use the effective moment of inertia.

7. For those steels that have both 33 and 50 ksi listings, if the design is based upon 50 ksi, the 50 ksi steel needs to be specified. (i.e., 362S137-54 (50 ksi))

1. Web-height to thickness ratio exceeds 200. Web Stiffeners are required at all support points and concentrated loads. Suitability of web holes must be evaluated independently.

2. Where web height-to-thickness ratio exceeds 260, or fl ange width-to-thickness ratio exceeds 60, effective properties are not calculated (limitations in AISI section B1)

* Allowable moment includes cold-work of forming.

J x 1000 (in4)

Cw (in6)

Xo (in) m (in)

Ro (in)

Lu (in) βlxe (in4)

Sxe (in3)

Ma (in-k)

Vag (lb)

Vanet (lb) lanoisroTEffective PropertiesGross Properties aerA thgieW xI xS xR yI yR ni( 2) )tf/bl( ni( 4) ni( 3) )ni( ni( 4) )ni(Member ngiseD ssenkcihT

)ni( Fy

(ksi)

162S125-18 0.0188 33 0.080 0.27 0.038 0.046 0.686 0.016 0.447 0.03 0.03 0.61 302 100 0.009 0.009 -1.029 0.594 1.315 0.388 29.0 162S125-27 0.0283 33 0.120 0.41 0.056 0.068 0.682 0.023 0.443 0.06 0.05 1.05 494 106 0.032 0.013 -1.017 0.587 1.302 0.390 29.1 162S125-30 0.0312 33 0.131 0.45 0.061 0.075 0.681 0.026 0.441 0.06 0.06 1.19 543 106 0.043 0.014 -1.014 0.585 1.298 0.390 29.0 162S125-33 0.0346 33 0.145 0.49 0.067 0.083 0.679 0.028 0.440 0.07 0.07 1.37 601 105 0.058 0.016 -1.010 0.583 1.294 0.391 29.3

250S125-18 0.0188 33 0.097 0.33 0.099 0.079 1.014 0.019 0.439 0.09 0.06 1.17 258 196 0.011 0.023 -0.904 0.543 1.427 0.599 29.0 250S125-27 0.0283 33 0.144 0.49 0.147 0.118 1.009 0.027 0.434 0.14 0.10 1.92 685 344 0.039 0.034 -0.893 0.536 1.416 0.602 28.8 250S125-30 0.0312 33 0.159 0.54 0.161 0.129 1.008 0.030 0.433 0.16 0.11 2.17 832 378 0.052 0.037 -0.889 0.534 1.412 0.603 28.9 250S125-33 0.0346 33 0.176 0.60 0.178 0.142 1.006 0.033 0.431 0.18 0.13 2.48 975 399 0.070 0.040 -0.885 0.532 1.408 0.605 28.8 250S125-43 0.0451 33 0.227 0.77 0.228 0.182 1.001 0.041 0.426 0.23 0.18 3.49 1265 394 0.154 0.050 -0.873 0.525 1.396 0.608 28.8 250S125-54 0.0566 50 0.280 0.95 0.277 0.222 0.994 0.049 0.419 0.28 0.22 4.98* 1553 373 0.299 0.060 -0.859 0.518 1.379 0.612 26.8 250S125-54 0.0566 50 0.280 0.95 0.277 0.222 0.994 0.049 0.419 0.33 0.27 6.30* 1891 342 0.299 0.060 -0.859 0.518 1.379 0.612 26.6 250S125-68 0.0713 50 0.345 1.18 0.334 0.267 0.984 0.057 0.408 0.27 0.21 6.25 2353 565 0.585 0.072 -0.839 0.508 1.356 0.617 23.2 250S125-68 0.0713 50 0.345 1.18 0.334 0.267 0.984 0.057 0.408 0.33 0.26 7.84 2866 519 0.585 0.072 -0.839 0.508 1.356 0.617 23.4

350S125-18 0.0188 33 0.115 0.39 0.215 0.123 1.366 0.021 0.423 0.20 0.07 1.42 180 159 0.014 0.050 -0.797 0.495 1.637 0.763 28.8 350S125-27 0.0283 33 0.173 0.59 0.320 0.183 1.361 0.030 0.418 0.32 0.13 2.57 614 359 0.046 0.072 -0.787 0.489 1.627 0.766 28.6 350S125-30 0.0312 33 0.190 0.65 0.351 0.201 1.359 0.033 0.417 0.35 0.15 2.96 824 436 0.062 0.079 -0.784 0.487 1.624 0.767 28.6 350S125-33 0.0346 33 0.210 0.72 0.387 0.221 1.358 0.036 0.415 0.38 0.18 3.45 1024 487 0.084 0.087 -0.780 0.485 1.620 0.768 28.6 350S125-43 0.0451 33 0.272 0.93 0.498 0.284 1.352 0.046 0.410 0.50 0.26 5.10 1739 631 0.184 0.109 -0.769 0.479 1.609 0.771 28.5 350S125-54 0.0566 33 0.337 1.15 0.608 0.348 1.344 0.055 0.402 0.61 0.33 6.49 2253 633 0.360 0.131 -0.755 0.471 1.593 0.775 28.3 350S125-54 0.0566 50 0.337 1.15 0.608 0.348 1.344 0.055 0.402 0.74 0.41 8.08 2774 592 0.360 0.131 -0.755 0.471 1.593 0.775 28.3 350S125-68 0.0713 33 0.417 1.42 0.739 0.422 1.332 0.064 0.391 0.60 0.31 9.22 3372 947 0.706 0.156 -0.737 0.462 1.571 0.780 22.9 350S125-68 0.0713 50 0.417 1.42 0.739 0.422 1.332 0.064 0.391 0.74 0.40 11.97 4202 897 0.706 0.156 -0.737 0.462 1.571 0.780 22.7

362S125-18 0.0188 33 0.118 0.40 0.234 0.129 1.409 0.021 0.421 0.22 0.08 1.48 173 163 0.014 0.054 -0.786 0.490 1.667 0.778 28.8 362S125-27 0.0283 33 0.176 0.60 0.347 0.192 1.404 0.031 0.416 0.34 0.14 2.67 592 370 0.047 0.079 -0.776 0.484 1.657 0.781 28.6 362S125-30 0.0312 33 0.194 0.66 0.381 0.210 1.402 0.033 0.415 0.38 0.16 3.08 794 449 0.063 0.086 -0.773 0.482 1.654 0.782 28.6 362S125-33 0.0346 33 0.215 0.73 0.421 0.232 1.400 0.037 0.413 0.42 0.18 3.59 1024 521 0.086 0.094 -0.769 0.480 1.650 0.783 28.6 362S125-43 0.0451 33 0.278 0.95 0.540 0.298 1.395 0.046 0.408 0.54 0.27 5.31 1739 676 0.188 0.118 -0.758 0.473 1.639 0.786 28.4 362S125-54 0.0566 33 0.344 1.17 0.661 0.365 1.386 0.055 0.400 0.66 0.34 6.78 2341 705 0.367 0.142 -0.744 0.466 1.623 0.790 28.3 362S125-54 0.0566 50 0.344 1.17 0.661 0.365 1.386 0.055 0.400 0.80 0.43 8.51 2884 662 0.367 0.142 -0.744 0.466 1.623 0.790 28.2 362S125-68 0.0713 33 0.426 1.45 0.803 0.443 1.374 0.065 0.389 0.66 0.32 9.62 3372 1016 0.721 0.169 -0.726 0.457 1.602 0.795 22.8 362S125-68 0.0713 50 0.426 1.45 0.803 0.443 1.374 0.065 0.389 0.80 0.42 12.52 4370 1004 0.721 0.169 -0.726 0.457 1.602 0.795 22.7

400S125-18¹ 0.0188 33 0.125 0.42 0.294 0.147 1.536 0.021 0.414 0.28 0.08 1.64 156 156 0.015 0.068 -0.754 0.475 1.760 0.816 28.8 400S125-27 0.0283 33 0.187 0.64 0.438 0.219 1.531 0.031 0.410 0.43 0.15 2.97 533 398 0.050 0.098 -0.744 0.469 1.751 0.819 28.5 400S125-30 0.0312 33 0.206 0.70 0.481 0.240 1.529 0.034 0.408 0.47 0.17 3.44 715 484 0.067 0.107 -0.741 0.467 1.748 0.820 28.4 400S125-33 0.0346 33 0.228 0.77 0.531 0.265 1.527 0.038 0.407 0.52 0.20 4.01 976 595 0.091 0.118 -0.738 0.465 1.744 0.821 28.5 400S125-43 0.0451 33 0.295 1.00 0.682 0.341 1.521 0.048 0.402 0.68 0.30 5.96 1739 810 0.200 0.148 -0.727 0.459 1.733 0.824 28.3 400S125-54 0.0566 33 0.365 1.24 0.835 0.418 1.512 0.057 0.394 0.84 0.39 7.65 2603 944 0.390 0.178 -0.713 0.451 1.718 0.828 28.1 400S125-54 0.0566 50 0.365 1.24 0.835 0.418 1.512 0.057 0.394 1.02 0.49 9.72 3215 895 0.390 0.178 -0.713 0.451 1.718 0.828 27.9 400S125-68 0.0713 33 0.452 1.54 1.017 0.509 1.499 0.066 0.383 0.83 0.36 10.81 3372 1223 0.767 0.213 -0.695 0.442 1.696 0.832 22.7 400S125-68 0.0713 50 0.452 1.54 1.017 0.509 1.499 0.066 0.383 1.02 0.47 14.18 4871 1356 0.767 0.213 -0.695 0.442 1.696 0.832 22.5

550S125-18¹,2 0.0188 33 0.153 0.52 0.630 0.229 2.029 0.023 0.390 0.018 0.140 -0.651 0.423 2.166 0.910 550S125-27 0.0283 33 0.229 0.78 0.938 0.341 2.023 0.034 0.385 0.90 0.25 4.86 382 382 0.061 0.205 -0.641 0.417 2.157 0.912 27.9 550S125-30 0.0312 33 0.252 0.86 1.031 0.375 2.021 0.037 0.384 1.00 0.29 5.65 512 512 0.082 0.224 -0.639 0.415 2.154 0.912 27.9 550S125-33 0.0346 33 0.279 0.95 1.139 0.414 2.019 0.041 0.382 1.11 0.34 6.62 699 699 0.112 0.246 -0.635 0.413 2.151 0.913 27.8 550S125-43 0.0451 33 0.362 1.23 1.468 0.534 2.013 0.052 0.377 1.46 0.50 9.88 1550 1199 0.246 0.309 -0.625 0.407 2.141 0.915 27.5 550S125-54 0.0566 33 0.450 1.53 1.805 0.656 2.002 0.061 0.369 1.81 0.65 12.79 2739 1666 0.481 0.374 -0.613 0.401 2.126 0.917 27.3 550S125-54 0.0566 50 0.450 1.53 1.805 0.656 2.002 0.061 0.369 2.21 0.80 18.94* 4347 2057 0.481 0.374 -0.613 0.401 2.126 0.917 24.6 550S125-68 0.0713 33 0.559 1.90 2.209 0.803 1.987 0.072 0.358 1.79 0.61 18.13 3093 1881 0.948 0.448 -0.597 0.392 2.106 0.920 22.1 550S125-68 0.0713 50 0.559 1.90 2.209 0.803 1.987 0.072 0.358 2.21 0.79 23.68 5350 2532 0.948 0.448 -0.597 0.392 2.106 0.920 21.8

Section Properties Non-Structural (S) Stud Section Properties (continued)

Structural (S) Stud Section Properties

1. Web-height to thickness ratio exceeds 200. Web Stiffeners are required at all support points and concentrated loads. Suitability of web holes must be evaluated independently.

2. Where web height-to-thickness ratio exceeds 260, or fl ange width-to-thickness ratio exceeds 60, effective properties are not calculated (limitations in AISI section B1)

* Allowable moment includes cold-work of forming.

See Section Properties Table Notes on page 6.

J x 1000 (in4)

Cw (in6)

Xo (in) m (in)

Ro (in)

Lu (in) βlxe (in4)

Sxe (in3)

Ma (in-k)

Vag (lb)

Vanet (lb) lanoisroTEffective PropertiesGross Properties aerA thgieW xI xS xR yI yR ni( 2) )tf/bl( ni( 4) ni( 3) )ni( ni( 4) )ni(Member ngiseD ssenkcihT

)ni( Fy

(ksi)

J x 1000 (in4)

Cw (in6)

Xo (in) m (in)

Ro (in)

Lu (in) βlxe (in4)

Sxe (in3)

Ma (in-k)

Vag (lb)

Vanet (lb) lanoisroTEffective PropertiesGross Properties aerA thgieW xI xS xR yI yR ni( 2) )tf/bl( ni( 4) ni( 3) )ni( ni( 4) )ni(Member ngiseD ssenkcihT

)ni( Fy

(ksi)

600S125-18¹,2 0.0188 33 0.162 0.55 0.778 0.259 2.189 0.024 0.382 0.019 0.172 -0.623 0.408 2.308 0.927 600S125-27¹ 0.0283 33 0.243 0.83 1.160 0.387 2.183 0.035 0.377 1.10 0.27 5.35 349 349 0.065 0.251 -0.614 0.402 2.299 0.929 27.7 600S125-30 0.0312 33 0.268 0.91 1.275 0.425 2.181 0.038 0.376 1.22 0.32 6.22 468 468 0.087 0.274 -0.611 0.401 2.296 0.929 27.7 600S125-33 0.0346 33 0.297 1.01 1.409 0.470 2.179 0.042 0.374 1.36 0.37 7.30 638 638 0.118 0.300 -0.608 0.399 2.293 0.930 27.5 600S125-43 0.0451 33 0.385 1.31 1.817 0.606 2.173 0.053 0.369 1.81 0.56 10.96 1416 1240 0.261 0.378 -0.598 0.393 2.284 0.931 27.3 600S125-54 0.0566 33 0.479 1.63 2.236 0.745 2.161 0.063 0.362 2.24 0.73 14.37 2739 1890 0.511 0.457 -0.586 0.386 2.269 0.933 27.1 600S125-54 0.0566 50 0.479 1.63 2.236 0.745 2.161 0.063 0.362 2.74 0.91 21.53* 4347 2339 0.511 0.457 -0.586 0.386 2.269 0.933 24.4 600S125-68 0.0713 33 0.595 2.02 2.740 0.913 2.146 0.073 0.351 2.22 0.67 20.15 2823 1947 1.008 0.548 -0.570 0.378 2.248 0.936 21.9 600S125-68 0.0713 50 0.595 2.02 2.740 0.913 2.146 0.073 0.351 2.74 0.90 26.88 5350 2879 1.008 0.548 -0.570 0.378 2.248 0.936 21.6 800S125-33¹ 0.0346 33 0.366 1.25 2.881 0.720 2.806 0.044 0.347 2.66 0.51 10.02 474 474 0.146 0.582 -0.519 0.349 2.875 0.967 26.6 800S125-43 0.0451 33 0.475 1.62 3.721 0.930 2.799 0.056 0.342 3.58 0.77 15.27 1051 1051 0.322 0.735 -0.510 0.344 2.865 0.968 26.3 800S125-54 0.0566 33 0.592 2.01 4.593 1.148 2.786 0.066 0.335 4.57 1.04 20.46 2091 2091 0.632 0.889 -0.499 0.338 2.850 0.969 26.0 800S125-54 0.0566 50 0.592 2.01 4.593 1.148 2.786 0.066 0.335 5.64 1.38 27.18 4221 3367 0.632 0.889 -0.499 0.338 2.850 0.969 25.6 800S125-68 0.0713 33 0.738 2.51 5.653 1.413 2.768 0.078 0.324 4.43 0.94 28.21 2091 2091 1.250 1.068 -0.485 0.330 2.829 0.971 21.1 800S125-68 0.0713 50 0.738 2.51 5.653 1.413 2.768 0.078 0.324 5.63 1.29 38.54 4221 3367 1.250 1.068 -0.485 0.330 2.829 0.971 20.8

250S137-33 0.0346 33 0.197 0.67 0.203 0.163 1.015 0.052 0.515 0.20 0.16 3.11 975 399 0.079 0.076 -1.141 0.677 1.612 0.499 35.5 250S137-43 0.0451 33 0.255 0.87 0.261 0.208 1.010 0.067 0.511 0.26 0.21 4.53* 1265 394 0.173 0.096 -1.129 0.670 1.599 0.501 33.7 250S137-54 0.0566 33 0.316 1.07 0.318 0.255 1.004 0.080 0.504 0.32 0.26 5.76* 1553 373 0.337 0.115 -1.115 0.663 1.583 0.504 33.3 250S137-54 0.0566 50 0.316 1.07 0.318 0.255 1.004 0.080 0.504 0.32 0.24 8.22* 2353 565 0.337 0.115 -1.115 0.663 1.583 0.504 27.0 250S137-68 0.0713 33 0.390 1.33 0.386 0.309 0.994 0.095 0.495 0.39 0.31 7.19* 1891 342 0.661 0.138 -1.096 0.653 1.561 0.507 33.2 250S137-68 0.0713 50 0.390 1.33 0.386 0.309 0.994 0.095 0.495 0.39 0.31 10.65* 2866 519 0.661 0.138 -1.096 0.653 1.561 0.507 26.8 250S162-33 0.0346 33 0.223 0.76 0.235 0.188 1.027 0.087 0.624 0.24 0.18 3.55 975 399 0.089 0.146 -1.470 0.859 1.898 0.401 44.1 250S162-43 0.0451 33 0.289 0.98 0.302 0.242 1.022 0.111 0.620 0.30 0.24 5.22* 1265 394 0.196 0.184 -1.457 0.852 1.885 0.402 42.0 250S162-54 0.0566 33 0.358 1.22 0.370 0.296 1.016 0.135 0.613 0.37 0.30 6.57* 1553 373 0.383 0.223 -1.443 0.845 1.868 0.403 41.8 250S162-54 0.0566 50 0.358 1.22 0.370 0.296 1.016 0.135 0.613 0.37 0.28 9.42* 2353 565 0.383 0.223 -1.443 0.845 1.868 0.403 33.9 250S162-68 0.0713 33 0.443 1.51 0.450 0.360 1.007 0.162 0.605 0.45 0.36 8.21* 1891 342 0.752 0.268 -1.424 0.835 1.846 0.405 41.7 250S162-68 0.0713 50 0.443 1.51 0.450 0.360 1.007 0.162 0.605 0.45 0.36 12.11* 2866 519 0.752 0.268 -1.424 0.835 1.846 0.405 33.7

350S162-33 0.0346 33 0.258 0.88 0.508 0.290 1.404 0.098 0.617 0.51 0.26 5.08 1024 487 0.103 0.277 -1.324 0.796 2.026 0.573 42.8 350S162-43 0.0451 33 0.334 1.14 0.654 0.374 1.400 0.125 0.612 0.65 0.36 7.05 1739 631 0.227 0.350 -1.312 0.789 2.014 0.575 42.6 350S162-54 0.0566 33 0.415 1.41 0.804 0.460 1.392 0.152 0.606 0.80 0.45 8.83 2253 633 0.443 0.426 -1.298 0.782 1.998 0.578 42.7 350S162-54 0.0566 50 0.415 1.41 0.804 0.460 1.392 0.152 0.606 0.80 0.43 12.74 3372 947 0.443 0.426 -1.298 0.782 1.998 0.578 34.5 350S162-68 0.0713 33 0.515 1.75 0.985 0.563 1.383 0.184 0.597 0.99 0.55 10.89 2774 592 0.872 0.514 -1.280 0.772 1.977 0.581 34.6 350S162-68 0.0713 50 0.515 1.75 0.985 0.563 1.383 0.184 0.597 0.99 0.55 16.44 4202 897 0.872 0.514 -1.280 0.772 1.977 0.581 34.5 350S300-43 2 0.0500 33 0.469 1.60 1.040 0.595 1.489 0.589 1.120 0.318 1.767 -2.697 1.539 3.278 0.323 350S300-54 0.0600 33 0.585 1.99 1.286 0.735 1.483 0.724 1.113 1.28 0.58 11.51 2253 633 0.624 2.166 -2.682 1.531 3.261 0.323 74.7 350S300-54 0.0600 50 0.585 1.99 1.286 0.735 1.483 0.724 1.113 1.21 0.51 15.20 3372 947 0.624 2.166 -2.682 1.531 3.261 0.323 60.4 350S300-68 0.0700 33 0.729 2.48 1.586 0.906 1.475 0.888 1.104 1.59 0.78 15.31 2774 592 1.235 2.649 -2.663 1.521 3.238 0.324 75.1 350S300-68 0.0700 50 0.729 2.48 1.586 0.906 1.475 0.888 1.104 1.56 0.69 20.56 4202 897 1.235 2.649 -2.663 1.521 3.238 0.324 60.5

362S137-33 0.0346 33 0.236 0.80 0.479 0.264 1.424 0.059 0.501 0.48 0.23 4.59 1024 521 0.094 0.165 -1.003 0.615 1.813 0.694 34.7 362S137-43 0.0451 33 0.306 1.04 0.616 0.340 1.419 0.075 0.497 0.62 0.32 6.32 1739 676 0.207 0.208 -0.991 0.608 1.801 0.697 34.6 362S137-54 0.0566 33 0.379 1.29 0.756 0.417 1.411 0.091 0.490 0.76 0.40 7.94 2341 705 0.405 0.251 -0.978 0.601 1.785 0.700 34.5 362S137-54 0.0566 50 0.379 1.29 0.756 0.417 1.411 0.091 0.490 0.76 0.38 11.42 3372 1016 0.405 0.251 -0.978 0.601 1.785 0.700 27.9 362S137-68 0.0713 33 0.470 1.60 0.922 0.509 1.401 0.109 0.480 0.92 0.50 9.84 2884 662 0.797 0.302 -0.959 0.592 1.764 0.704 34.6 362S137-68 0.0713 50 0.470 1.60 0.922 0.509 1.401 0.109 0.480 0.92 0.49 14.77 4370 1004 0.797 0.302 -0.959 0.592 1.764 0.704 27.8 362S162-33 0.0346 33 0.262 0.89 0.551 0.304 1.450 0.099 0.616 0.55 0.27 5.29 1024 521 0.105 0.297 -1.308 0.789 2.048 0.592 42.6 362S162-43 0.0451 33 0.340 1.16 0.710 0.392 1.445 0.127 0.611 0.71 0.37 7.34 1739 676 0.230 0.376 -1.297 0.782 2.036 0.594 42.5 362S162-54 0.0566 33 0.422 1.44 0.873 0.481 1.438 0.154 0.604 0.87 0.47 9.22 2341 705 0.451 0.457 -1.283 0.774 2.020 0.597 42.5 362S162-54 0.0566 50 0.422 1.44 0.873 0.481 1.438 0.154 0.604 0.87 0.44 13.28 3372 1016 0.451 0.457 -1.283 0.774 2.020 0.597 34.4 362S162-68 0.0713 33 0.524 1.78 1.069 0.590 1.429 0.186 0.596 1.07 0.58 11.43 2884 662 0.887 0.552 -1.264 0.765 1.998 0.600 42.7 362S162-68 0.0713 50 0.524 1.78 1.069 0.590 1.429 0.186 0.596 1.07 0.57 17.18 4370 1004 0.887 0.552 -1.264 0.765 1.998 0.600 34.3 362S200-33 0.0346 33 0.297 1.01 0.648 0.358 1.478 0.177 0.772 0.65 0.29 5.81 1024 521 0.118 0.577 -1.741 1.030 2.411 0.478 53.5 362S200-43 0.0451 33 0.385 1.31 0.836 0.461 1.474 0.227 0.767 0.84 0.43 8.43 1739 676 0.261 0.734 -1.729 1.024 2.398 0.480 53.5 362S200-54 0.0566 33 0.479 1.63 1.030 0.568 1.467 0.277 0.761 1.03 0.55 10.93 2341 705 0.511 0.896 -1.715 1.016 2.382 0.482 53.6 362S200-54 0.0566 50 0.479 1.63 1.030 0.568 1.467 0.277 0.761 1.03 0.49 14.66 3372 1016 0.511 0.896 -1.715 1.016 2.382 0.482 43.3 362S200-68 0.0713 33 0.595 2.02 1.265 0.698 1.458 0.337 0.753 1.27 0.69 13.58 2884 662 1.008 1.089 -1.696 1.006 2.360 0.484 53.8 362S200-68 0.0713 50 0.595 2.02 1.265 0.698 1.458 0.337 0.753 1.27 0.67 19.95 4370 1004 1.008 1.089 -1.696 1.006 2.360 0.484 43.4 362S300-33 2 0.0300 33 0.366 1.25 0.871 0.481 1.543 0.463 1.125 0.146 1.478 -2.666 1.537 3.296 0.336 362S300-43 2 0.0500 33 0.475 1.62 1.125 0.621 1.539 0.596 1.120 0.322 1.888 -2.674 1.530 3.282 0.336 362S300-54 0.0600 33 0.592 2.01 1.390 0.767 1.533 0.734 1.114 1.38 0.61 11.99 2341 705 0.632 2.316 -2.659 1.522 3.265 0.337 74.5 362S300-54 0.0600 50 0.592 2.01 1.390 0.767 1.533 0.734 1.114 1.31 0.53 15.83 3372 1016 0.632 2.316 -2.659 1.522 3.265 0.337 60.3 362S300-68 0.0700 33 0.738 2.51 1.716 0.947 1.525 0.900 1.105 1.72 0.81 16.02 2884 662 1.250 2.833 -2.640 1.512 3.243 0.337 74.9 362S300-68 0.0700 50 0.738 2.51 1.716 0.947 1.525 0.900 1.105 1.68 0.72 21.44 4370 1004 1.250 2.833 -2.640 1.512 3.243 0.337 60.4

Administrator Text Box 0.0451

Administrator Text Box 0.0566

Administrator Text Box 0.0566

Administrator Text Box 0.0713

Administrator Text Box 0.0713

Administrator Text Box 0.0451

Administrator Text Box 0.0566

Administrator Text Box 0.0566

Administrator Text Box 0.0713

Administrator Text Box 0.0713

Administrator Text Box 0.0346

Administrator Rectangle

Section Properties

1. Web-height to thickness ratio exceeds 200. Web Stiffeners are required at all support points and concentrated loads. Suitability of web holes must be evaluated independently.

2. Where web height-to-thickness ratio exceeds 260, or fl ange width-to-thickness ratio exceeds 60, effective properties are not calculated (limitations in AISI section B1)

* Allowable moment includes cold-work of forming.

See Section Properties Table Notes on page 6.

J x 1000 (in4)

Cw (in6)

Xo (in) m (in)

Ro (in)

Lu (in) βlxe (in4)

Sxe (in3)

Ma (in-k)

Vag (lb)

Vanet (lb) lanoisroTEffective PropertiesGross Properties aerA thgieW xI xS xR yI yR ni( 2) )tf/bl( ni( 4) ni( 3) )ni( ni( 4) )ni(Member ngiseD ssenkcihT

)ni( Fy

(ksi)

400S137-33 0.0346 33 0.249 0.85 0.603 0.301 1.556 0.061 0.496 0.60 0.26 5.12 976 595 0.099 0.204 -0.965 0.597 1.897 0.741 34.5 400S137-43 0.0451 33 0.323 1.10 0.776 0.388 1.551 0.078 0.491 0.78 0.36 7.09 1739 810 0.219 0.257 -0.954 0.591 1.885 0.744 34.4 400S137-54 0.0566 33 0.401 1.36 0.953 0.477 1.542 0.094 0.484 0.95 0.45 8.96 2603 944 0.428 0.311 -0.940 0.583 1.870 0.747 34.2 400S137-54 0.0566 50 0.401 1.36 0.953 0.477 1.542 0.094 0.484 0.95 0.43 12.82 3372 1223 0.428 0.311 -0.940 0.583 1.870 0.747 27.7 400S137-68 0.0713 33 0.497 1.69 1.165 0.582 1.531 0.112 0.475 1.17 0.57 11.21 3215 895 0.842 0.375 -0.922 0.574 1.849 0.751 34.3 400S137-68 0.0713 50 0.497 1.69 1.165 0.582 1.531 0.112 0.475 1.17 0.56 16.70 4871 1356 0.842 0.375 -0.922 0.574 1.849 0.751 27.6 400S162-33 0.0346 33 0.275 0.94 0.692 0.346 1.586 0.103 0.611 0.69 0.30 5.91 976 595 0.110 0.363 -1.263 0.768 2.118 0.644 42.3 400S162-43 0.0451 33 0.357 1.21 0.892 0.446 1.581 0.131 0.606 0.89 0.42 8.23 1739 810 0.242 0.460 -1.252 0.761 2.106 0.647 42.2 400S162-54 0.0566 33 0.443 1.51 1.098 0.549 1.574 0.159 0.600 1.10 0.53 10.39 2603 944 0.473 0.560 -1.238 0.754 2.090 0.649 42.2 400S162-54 0.0566 50 0.443 1.51 1.098 0.549 1.574 0.159 0.600 1.10 0.50 14.90 3372 1223 0.473 0.560 -1.238 0.754 2.090 0.649 34.1 400S162-68 0.0713 33 0.550 1.87 1.346 0.673 1.564 0.192 0.591 1.35 0.66 13.00 3215 895 0.933 0.677 -1.220 0.745 2.069 0.653 42.2 400S162-68 0.0713 50 0.550 1.87 1.346 0.673 1.564 0.192 0.591 1.35 0.65 19.41 4871 1356 0.933 0.677 -1.220 0.745 2.069 0.653 34.0 400S200-33 0.0346 33 0.310 1.05 0.812 0.406 1.619 0.183 0.769 0.81 0.33 6.49 976 595 0.124 0.697 -1.688 1.007 2.462 0.530 53.1 400S200-43 0.0451 33 0.402 1.37 1.047 0.524 1.615 0.235 0.764 1.05 0.48 9.45 1739 810 0.272 0.886 -1.676 1.000 2.449 0.532 53.0 400S200-54 0.0566 33 0.500 1.70 1.292 0.646 1.608 0.287 0.758 1.29 0.62 12.30 2603 944 0.534 1.083 -1.662 0.993 2.433 0.534 53.1 400S200-54 0.0566 50 0.500 1.70 1.292 0.646 1.608 0.287 0.758 1.29 0.55 16.43 3372 1223 0.534 1.083 -1.662 0.993 2.433 0.534 42.9 400S200-68 0.0713 33 0.622 2.12 1.589 0.795 1.599 0.349 0.750 1.59 0.78 15.40 3215 895 1.054 1.318 -1.643 0.983 2.412 0.536 53.2 400S200-68 0.0713 50 0.622 2.12 1.589 0.795 1.599 0.349 0.750 1.59 0.75 22.48 4871 1356 1.054 1.318 -1.643 0.983 2.412 0.536 42.9 400S300-33 2 0.0300 33 0.379 1.29 1.084 0.542 1.691 0.479 1.125 0.151 1.786 -2.621 1.510 3.316 0.375 400S300-43 2 0.0451 33 0.492 1.67 1.400 0.700 1.687 0.617 1.120 0.334 2.282 -2.608 1.503 3.302 0.376 400S300-54 0.0566 33 0.613 2.09 1.732 0.866 1.681 0.760 1.114 1.72 0.68 13.44 2603 944 0.655 2.802 -2.594 1.496 3.285 0.377 74.1 400S300-54 0.0566 50 0.613 2.09 1.732 0.866 1.681 0.760 1.114 1.64 0.59 17.72 3372 1223 0.655 2.802 -2.594 1.496 3.285 0.377 59.9 400S300-68 0.0713 33 0.764 2.60 2.139 1.070 1.673 0.933 1.105 2.14 0.91 18.06 3215 895 1.295 3.432 -2.574 1.486 3.263 0.378 74.3 400S300-68 0.0713 50 0.764 2.60 2.139 1.070 1.673 0.933 1.105 2.10 0.81 24.09 4871 1356 1.295 3.432 -2.574 1.486 3.263 0.378 60.0

550S162-33 0.0346 33 0.327 1.11 1.458 0.530 2.112 0.113 0.589 1.46 0.51 10.11 699 699 0.130 0.713 -1.114 0.697 2.459 0.795 41.4 550S162-43 0.0451 33 0.424 1.44 1.883 0.685 2.107 0.145 0.584 1.88 0.68 14.79* 1550 1199 0.288 0.905 -1.103 0.691 2.448 0.797 39.2 550S162-54 0.0566 33 0.528 1.80 2.324 0.845 2.098 0.176 0.577 2.32 0.85 18.76* 2739 1666 0.564 1.105 -1.090 0.684 2.434 0.800 38.7 550S162-54 0.0566 50 0.528 1.80 2.324 0.845 2.098 0.176 0.577 2.32 0.81 26.86* 3093 1881 0.564 1.105 -1.090 0.684 2.434 0.800 31.6 550S162-68 0.0713 33 0.657 2.24 2.861 1.040 2.086 0.212 0.568 2.86 1.04 23.72* 4347 2057 1.114 1.342 -1.072 0.675 2.414 0.803 38.0 550S162-68 0.0713 50 0.657 2.24 2.861 1.040 2.086 0.212 0.568 2.86 1.03 34.94* 5350 2532 1.114 1.342 -1.072 0.675 2.414 0.803 31.1 550S300-33 2 0.0346 33 0.431 1.47 2.210 0.804 2.265 0.536 1.115 0.172 3.401 -2.392 1.415 3.478 0.527 550S300-43 2 0.0451 33 0.560 1.90 2.860 1.040 2.261 0.690 1.110 0.379 4.357 -2.380 1.408 3.465 0.528 550S300-54 0.0566 33 0.698 2.37 3.545 1.289 2.254 0.850 1.104 3.51 1.08 21.34 2739 1666 0.745 5.364 -2.365 1.401 3.449 0.530 73.1 550S300-54 0.0566 50 0.698 2.37 3.545 1.289 2.254 0.850 1.104 3.30 0.98 29.44 3093 1881 0.745 5.364 -2.365 1.401 3.449 0.530 59.2 550S300-68 0.0713 33 0.871 2.96 4.391 1.597 2.245 1.044 1.095 4.38 1.41 27.88 4347 2057 1.476 6.594 -2.346 1.391 3.427 0.531 73.1 550S300-68 0.0713 50 0.871 2.96 4.391 1.597 2.245 1.044 1.095 4.29 1.29 38.53 5350 2532 1.476 6.594 -2.346 1.391 3.427 0.531 59.1

600S137-33 0.0346 33 0.318 1.08 1.582 0.527 2.229 0.069 0.464 1.55 0.46 8.98 638 638 0.127 0.500 -0.807 0.519 2.416 0.889 33.5 600S137-43 0.0451 33 0.413 1.41 2.042 0.681 2.223 0.087 0.459 2.04 0.65 12.74 1416 1240 0.280 0.633 -0.796 0.513 2.406 0.890 33.2 600S137-54 0.0566 33 0.514 1.75 2.518 0.839 2.213 0.105 0.452 2.52 0.83 16.44 2739 1890 0.549 0.769 -0.784 0.506 2.391 0.893 33.0 600S137-54 0.0566 50 0.514 1.75 2.518 0.839 2.213 0.105 0.452 2.52 0.78 23.26 2823 1947 0.549 0.769 -0.784 0.506 2.391 0.893 26.8 600S137-68 0.0713 33 0.640 2.18 3.094 1.031 2.200 0.125 0.443 3.09 1.03 24.05* 4347 2339 1.084 0.930 -0.768 0.497 2.371 0.895 30.2 600S137-68 0.0713 50 0.640 2.18 3.094 1.031 2.200 0.125 0.443 3.09 1.03 30.84 5350 2879 1.084 0.930 -0.768 0.497 2.371 0.895 26.6 600S137-97 0.1017 33 0.889 3.03 4.188 1.396 2.170 0.159 0.422 4.19 1.40 34.48* 6911 2512 3.066 1.216 -0.734 0.480 2.330 0.901 28.8 600S137-97 0.1017 50 0.889 3.03 4.188 1.396 2.170 0.159 0.422 4.19 1.40 50.80* 10472 3805 3.066 1.216 -0.734 0.480 2.330 0.901 23.6 600S162-33 0.0346 33 0.344 1.17 1.793 0.598 2.282 0.116 0.581 1.79 0.58 11.41 638 638 0.137 0.861 -1.072 0.677 2.587 0.828 41.1 600S162-43 0.0451 33 0.447 1.52 2.316 0.772 2.276 0.148 0.576 2.32 0.77 16.68* 1416 1240 0.303 1.095 -1.062 0.670 2.577 0.830 39.0 600S162-54 0.0566 33 0.556 1.89 2.860 0.953 2.267 0.180 0.570 2.86 0.95 21.17* 2739 1890 0.594 1.337 -1.049 0.663 2.562 0.832 38.4 600S162-54 0.0566 50 0.556 1.89 2.860 0.953 2.267 0.180 0.570 2.86 0.92 30.33* 2823 1947 0.594 1.337 -1.049 0.663 2.562 0.832 31.4 600S162-68 0.0713 33 0.693 2.36 3.525 1.175 2.255 0.218 0.560 3.53 1.18 26.79* 4347 2339 1.174 1.626 -1.032 0.655 2.543 0.835 37.7 600S162-68 0.0713 50 0.693 2.36 3.525 1.175 2.255 0.218 0.560 3.53 1.16 39.47* 5350 2879 1.174 1.626 -1.032 0.655 2.543 0.835 30.8 600S162-97 0.1017 33 0.966 3.29 4.797 1.599 2.229 0.283 0.541 4.80 1.60 38.37* 6911 2512 3.329 2.153 -0.997 0.636 2.501 0.841 36.4 600S162-97 0.1017 50 0.966 3.29 4.797 1.599 2.229 0.283 0.541 4.80 1.60 56.73* 10472 3805 3.329 2.153 -0.997 0.636 2.501 0.841 29.8 600S162-118 0.1242 33 1.158 3.94 5.652 1.884 2.209 0.321 0.526 5.65 1.88 46.82* 8267 2391 5.956 2.487 -0.971 0.623 2.470 0.845 35.6 600S162-118 0.1242 50 1.158 3.94 5.652 1.884 2.209 0.321 0.526 5.65 1.88 68.94* 12526 3622 5.956 2.487 -0.971 0.623 2.470 0.845 29.0 600S200-33 0.0346 33 0.379 1.29 2.075 0.692 2.340 0.209 0.743 2.06 0.62 12.28 638 638 0.151 1.593 -1.457 0.901 2.855 0.740 51.6 600S200-43 0.0451 33 0.492 1.67 2.683 0.894 2.335 0.268 0.739 2.68 0.87 17.24 1416 1240 0.334 2.033 -1.446 0.894 2.844 0.742 51.5 600S200-54 0.0566 33 0.613 2.09 3.319 1.106 2.327 0.328 0.732 3.32 1.11 24.07* 2739 1890 0.655 2.493 -1.432 0.887 2.829 0.744 48.9 600S200-54 0.0566 50 0.613 2.09 3.319 1.106 2.327 0.328 0.732 3.32 1.02 30.40 2823 1947 0.655 2.493 -1.432 0.887 2.829 0.744 41.6 600S200-68 0.0713 33 0.764 2.60 4.101 1.367 2.316 0.400 0.723 4.10 1.37 30.42* 4347 2339 1.295 3.047 -1.415 0.878 2.809 0.746 48.2 600S200-68 0.0713 50 0.764 2.60 4.101 1.367 2.316 0.400 0.723 4.10 1.32 43.71* 5350 2879 1.295 3.047 -1.415 0.878 2.809 0.746 39.3 600S200-97 0.1017 33 1.067 3.63 5.612 1.871 2.293 0.530 0.705 5.61 1.87 43.49* 6911 2512 3.679 4.080 -1.378 0.859 2.767 0.752 46.9 600S200-97 0.1017 50 1.067 3.63 5.612 1.871 2.293 0.530 0.705 5.61 1.87 64.53* 10472 3805 3.679 4.080 -1.378 0.859 2.767 0.752 38.3 600S200-118 0.1242 33 1.283 4.36 6.641 2.214 2.275 0.611 0.690 6.64 2.21 53.05* 8267 2391 6.595 4.753 -1.351 0.845 2.735 0.756 46.1 600S200-118 0.1242 50 1.283 4.36 6.641 2.214 2.275 0.611 0.690 6.64 2.21 78.44* 12526 3622 6.595 4.753 -1.351 0.845 2.735 0.756 37.6 600S250-43 0.0451 33 0.537 1.83 3.082 1.027 2.396 0.458 0.923 3.08 0.92 18.14 1416 1240 0.364 3.411 -1.874 1.136 3.179 0.652 62.4 600S250-54 0.0566 33 0.670 2.28 3.819 1.273 2.388 0.562 0.917 3.82 1.16 22.90 2739 1890 0.715 4.194 -1.860 1.129 3.163 0.654 62.3 600S250-54 0.0566 50 0.670 2.28 3.819 1.273 2.388 0.562 0.917 3.77 1.07 32.00 2823 1947 0.715 4.194 -1.860 1.129 3.163 0.654 50.5 600S250-68 0.0713 33 0.836 2.84 4.727 1.576 2.378 0.688 0.908 4.73 1.51 32.82* 4347 2339 1.416 5.145 -1.842 1.119 3.142 0.656 59.2 600S250-68 0.0713 50 0.836 2.84 4.727 1.576 2.378 0.688 0.908 4.72 1.39 41.49 5350 2879 1.416 5.145 -1.842 1.119 3.142 0.656 50.4 600S250-97 0.1017 33 1.169 3.98 6.496 2.165 2.357 0.923 0.889 6.50 2.16 48.81* 6911 2512 4.030 6.947 -1.803 1.100 3.098 0.661 58.1 600S250-97 0.1017 50 1.169 3.98 6.496 2.165 2.357 0.923 0.889 6.50 2.06 69.38* 10472 3805 4.030 6.947 -1.803 1.100 3.098 0.661 47.3 600S250-118 0.1242 33 1.407 4.79 7.713 2.571 2.342 1.075 0.874 7.71 2.57 59.58* 8267 2391 7.234 8.142 -1.775 1.085 3.066 0.665 57.3 600S250-118 0.1242 50 1.407 4.79 7.713 2.571 2.342 1.075 0.874 7.71 2.50 85.92* 12526 3622 7.234 8.142 -1.775 1.085 3.066 0.665 46.7

Administrator Rectangle

Administrator Text Box 0.0346

1. Web-height to thickness ratio exceeds 200. Web Stiffeners are required at all support points and concentrated loads.

* Allowable moment includes cold-work of forming. Suitability of web holes must be evaluated independently.

See Section Properties Table Notes on page 6.

J x 1000 (in4)

Cw (in6)

Xo (in) m (in)

Ro (in)

Lu (in) βlxe (in4)

Sxe (in3)

Ma (in-k)

Vag (lb)

Vanet (lb) lanoisroTEffective PropertiesGross Properties aerA thgieW xI xS xR yI yR ni( 2) )tf/bl( ni( 4) ni( 3) )ni( ni( 4) )ni(Member ngiseD ssenkcihT

)ni( Fy

(ksi)

600S300-68 0.0713 33 0.907 3.09 5.354 1.785 2.430 1.075 1.089 5.34 1.58 31.23 4347 2339 1.537 7.937 -2.280 1.363 3.505 0.577 72.8 600S300-68 0.0713 50 0.907 3.09 5.354 1.785 2.430 1.075 1.089 5.22 1.45 43.30 5350 2879 1.537 7.937 -2.280 1.363 3.505 0.577 59.9 600S300-97 0.1017 33 1.271 4.32 7.381 2.460 2.410 1.454 1.070 7.38 2.35 52.07* 6911 2512 4.381 10.776 -2.241 1.343 3.461 0.581 68.8 600S300-97 0.1017 50 1.271 4.32 7.381 2.460 2.410 1.454 1.070 7.28 2.25 67.28 10472 3805 4.381 10.776 -2.241 1.343 3.461 0.581 58.9 600S300-118 0.1242 33 1.531 5.21 8.785 2.928 2.395 1.704 1.055 8.79 2.84 64.29* 8267 2391 7.872 12.683 -2.212 1.328 3.427 0.583 68.1 600S300-118 0.1242 50 1.531 5.21 8.785 2.928 2.395 1.704 1.055 8.71 2.80 94.24* 12526 3622 7.872 12.683 -2.212 1.328 3.427 0.583 55.4 600S350-54 0.0566 33 0.825 2.81 5.022 1.674 2.467 1.491 1.344 4.91 1.45 28.70 2739 1890 0.881 12.942 -3.037 1.787 4.137 0.461 91.8 600S350-54 0.0566 50 0.825 2.81 5.022 1.674 2.467 1.491 1.344 4.72 1.34 39.97 2823 1947 0.881 12.942 -3.037 1.787 4.137 0.461 74.4 600S350-68 0.0713 33 1.032 3.51 6.237 2.079 2.459 1.841 1.336 6.24 1.95 38.50 4347 2339 1.748 15.968 -3.018 1.777 4.115 0.462 91.8 600S350-68 0.0713 50 1.032 3.51 6.237 2.079 2.459 1.841 1.336 6.17 1.77 53.01 5350 2879 1.748 15.968 -3.018 1.777 4.115 0.462 74.4 600S350-97 0.1017 33 1.449 4.93 8.631 2.877 2.441 2.518 1.318 8.63 2.82 61.55* 6911 2512 4.994 21.811 -2.979 1.757 4.071 0.464 87.5 600S350-97 0.1017 50 1.449 4.93 8.631 2.877 2.441 2.518 1.318 8.63 2.59 77.64 10472 3805 4.994 21.811 -2.979 1.757 4.071 0.464 74.4 600S350-118 0.1242 33 1.748 5.95 10.304 3.435 2.428 2.978 1.305 10.30 3.44 76.39* 8267 2391 8.990 25.791 -2.951 1.742 4.038 0.466 86.9 600S350-118 0.1242 50 1.748 5.95 10.304 3.435 2.428 2.978 1.305 10.30 3.27 108.43* 12526 3622 8.990 25.791 -2.951 1.742 4.038 0.466 70.6

800S137-33 0.0346 33 0.388 1.32 3.198 0.799 2.873 0.073 0.435 3.00 0.62 12.30 474 474 0.155 0.957 -0.696 0.460 2.987 0.946 32.5 800S137-43 0.0451 33 0.503 1.71 4.134 1.033 2.866 0.093 0.430 4.00 0.90 17.70 1051 1051 0.341 1.214 -0.687 0.454 2.978 0.947 32.2 800S137-54 0.0566 33 0.627 2.13 5.110 1.277 2.855 0.112 0.423 5.08 1.18 23.29 2091 2091 0.670 1.478 -0.676 0.448 2.964 0.948 32.0 800S137-54 0.0566 50 0.627 2.13 5.110 1.277 2.855 0.112 0.423 4.97 1.08 32.42 2091 2091 0.670 1.478 -0.676 0.448 2.964 0.948 25.9 800S137-68 0.0713 33 0.782 2.66 6.303 1.576 2.839 0.134 0.414 6.30 1.54 30.45 4221 3367 1.325 1.789 -0.661 0.440 2.944 0.950 31.6 800S137-68 0.0713 50 0.782 2.66 6.303 1.576 2.839 0.134 0.414 6.29 1.47 43.96 4221 3367 1.325 1.789 -0.661 0.440 2.944 0.950 25.6 800S137-97 0.1017 33 1.093 3.72 8.597 2.149 2.805 0.169 0.394 8.60 2.15 53.09* 8843 4824 3.767 2.349 -0.630 0.423 2.902 0.953 27.6 800S137-97 0.1017 50 1.093 3.72 8.597 2.149 2.805 0.169 0.394 8.60 2.15 64.35 10885 5938 3.767 2.349 -0.630 0.423 2.902 0.953 25.0 800S162-33¹ 0.0346 33 0.413 1.41 3.582 0.896 2.943 0.125 0.550 3.38 0.71 14.03 474 474 0.165 1.630 -0.936 0.607 3.137 0.911 40.1 800S162-43 0.0451 33 0.537 1.83 4.633 1.158 2.937 0.160 0.546 4.50 1.02 20.14 1051 1051 0.364 2.076 -0.926 0.601 3.128 0.912 39.9 800S162-54 0.0566 33 0.670 2.28 5.736 1.434 2.927 0.194 0.539 5.70 1.33 26.36 2091 2091 0.715 2.539 -0.914 0.594 3.113 0.914 39.6 800S162-54 0.0566 50 0.670 2.28 5.736 1.434 2.927 0.194 0.539 5.60 1.23 36.79 2091 2091 0.715 2.539 -0.914 0.594 3.113 0.914 32.1 800S162-68 0.0713 33 0.836 2.84 7.089 1.772 2.913 0.235 0.530 7.09 1.74 34.32 4221 3367 1.416 3.093 -0.899 0.586 3.094 0.916 39.3 800S162-68 0.0713 50 0.836 2.84 7.089 1.772 2.913 0.235 0.530 7.07 1.66 49.80 4221 3367 1.416 3.093 -0.899 0.586 3.094 0.916 31.9 800S162-97 0.1017 33 1.169 3.98 9.713 2.428 2.883 0.305 0.510 9.71 2.43 58.27* 8843 4824 4.030 4.114 -0.866 0.568 3.053 0.919 35.1 800S162-97 0.1017 50 1.169 3.98 9.713 2.428 2.883 0.305 0.510 9.71 2.43 72.70 10885 5938 4.030 4.114 -0.866 0.568 3.053 0.919 31.4 800S162-118 0.1242 33 1.407 4.79 11.504 2.876 2.860 0.345 0.496 11.50 2.88 71.47* 11341 4971 7.234 4.766 -0.842 0.556 3.022 0.922 34.1 800S162-118 0.1242 50 1.407 4.79 11.504 2.876 2.860 0.345 0.496 11.50 2.88 105.23* 16235 7115 7.234 4.766 -0.842 0.556 3.022 0.922 28.0 800S200-33¹ 0.0346 33 0.448 1.52 4.096 1.024 3.023 0.227 0.712 4.10 0.82 16.12 474 474 0.179 2.971 -1.288 0.817 3.363 0.853 50.5 800S200-43 0.0451 33 0.582 1.98 5.302 1.325 3.018 0.292 0.708 5.30 1.29 25.54 1051 1051 0.395 3.797 -1.277 0.811 3.353 0.855 50.4 800S200-54 0.0566 33 0.726 2.47 6.573 1.643 3.009 0.357 0.701 6.57 1.64 35.75* 2091 2091 0.775 4.663 -1.265 0.804 3.338 0.856 47.8 800S200-54 0.0566 50 0.726 2.47 6.573 1.643 3.009 0.357 0.701 6.57 1.50 44.87 2091 2091 0.775 4.663 -1.265 0.804 3.338 0.856 40.7 800S200-68 0.0713 33 0.907 3.09 8.140 2.035 2.996 0.435 0.692 8.14 2.04 45.29* 4221 3367 1.537 5.712 -1.248 0.796 3.319 0.859 47.0 800S200-68 0.0713 50 0.907 3.09 8.140 2.035 2.996 0.435 0.692 8.14 1.96 65.21* 4221 3367 1.537 5.712 -1.248 0.796 3.319 0.859 38.4 800S200-97 0.1017 33 1.271 4.32 11.203 2.801 2.969 0.576 0.673 11.20 2.80 65.12* 8843 4824 4.381 7.684 -1.214 0.777 3.278 0.863 45.5 800S200-97 0.1017 50 1.271 4.32 11.203 2.801 2.969 0.576 0.673 11.20 2.80 96.63* 10885 5938 4.381 7.684 -1.214 0.777 3.278 0.863 37.2 800S200-118 0.1242 33 1.531 5.21 13.316 3.329 2.949 0.665 0.659 13.32 3.33 79.78* 11341 4971 7.872 8.981 -1.188 0.764 3.247 0.866 44.6 800S200-118 0.1242 50 1.531 5.21 13.316 3.329 2.949 0.665 0.659 13.32 3.33 117.95* 16235 7115 7.872 8.981 -1.188 0.764 3.247 0.866 36.5 800S250-43 0.0451 33 0.627 2.13 6.015 1.504 3.097 0.500 0.893 6.02 1.31 25.95 1051 1051 0.425 6.374 -1.675 1.043 3.632 0.787 61.5 800S250-54 0.0566 33 0.783 2.66 7.465 1.866 3.088 0.614 0.886 7.47 1.71 33.82 2091 2091 0.836 7.850 -1.661 1.036 3.617 0.789 61.4 800S250-54 0.0566 50 0.783 2.66 7.465 1.866 3.088 0.614 0.886 7.38 1.53 45.66 2091 2091 0.836 7.850 -1.661 1.036 3.617 0.789 49.8 800S250-68 0.0713 33 0.978 3.33 9.261 2.315 3.077 0.752 0.877 9.26 2.22 48.33* 4221 3367 1.658 9.652 -1.644 1.027 3.597 0.791 58.2 800S250-68 0.0713 50 0.978 3.33 9.261 2.315 3.077 0.752 0.877 9.24 2.06 61.65 4221 3367 1.658 9.652 -1.644 1.027 3.597 0.791 49.6 800S250-97 0.1017 33 1.372 4.67 12.789 3.197 3.053 1.009 0.857 12.79 3.19 72.07* 8843 4824 4.731 13.091 -1.607 1.008 3.555 0.796 56.8 800S250-97 0.1017 50 1.372 4.67 12.789 3.197 3.053 1.009 0.857 12.79 3.05 102.70* 10885 5938 4.731 13.091 -1.607 1.008 3.555 0.796 46.4 800S250-118 0.1242 33 1.655 5.63 15.242 3.810 3.035 1.175 0.843 15.24 3.81 88.31* 11341 4971 8.511 15.395 -1.580 0.994 3.524 0.799 55.9 800S250-118 0.1242 50 1.655 5.63 15.242 3.810 3.035 1.175 0.843 15.24 3.71 127.51* 16235 7115 8.511 15.395 -1.580 0.994 3.524 0.799 45.6 800S300-68 0.0713 33 1.050 3.57 10.382 2.595 3.145 1.179 1.060 10.35 2.32 45.86 4221 3367 1.779 14.888 -2.055 1.262 3.903 0.723 72.0 800S300-68 0.0713 50 1.050 3.57 10.382 2.595 3.145 1.179 1.060 10.08 2.15 64.21 4221 3367 1.779 14.888 -2.055 1.262 3.903 0.723 58.4 800S300-97 0.1017 33 1.474 5.02 14.375 3.594 3.123 1.595 1.040 14.38 3.44 76.21* 8843 4824 5.082 20.304 -2.017 1.243 3.860 0.727 67.7 800S300-97 0.1017 50 1.474 5.02 14.375 3.594 3.123 1.595 1.040 14.17 3.30 98.92 10885 5938 5.082 20.304 -2.017 1.243 3.860 0.727 58.1 800S300-118 0.1242 33 1.779 6.05 17.167 4.292 3.106 1.871 1.025 17.17 4.17 94.33* 11341 4971 9.149 23.979 -1.989 1.229 3.828 0.730 66.8 800S300-118 0.1242 50 1.779 6.05 17.167 4.292 3.106 1.871 1.025 17.02 4.11 138.41* 16235 7115 9.149 23.979 -1.989 1.229 3.828 0.730 54.5 800S350-54 0.0566 33 0.938 3.19 9.683 2.421 3.212 1.646 1.325 9.48 2.13 41.98 2091 2091 1.002 22.897 -2.766 1.668 4.441 0.612 90.1 800S350-54 0.0566 50 0.938 3.19 9.683 2.421 3.212 1.646 1.325 9.19 1.87 55.96 2091 2091 1.002 22.897 -2.766 1.668 4.441 0.612 73.1 800S350-68 0.0713 33 1.174 4.00 12.046 3.012 3.203 2.034 1.316 12.05 2.84 56.07 4221 3367 1.990 28.308 -2.748 1.658 4.421 0.614 89.9 800S350-68 0.0713 50 1.174 4.00 12.046 3.012 3.203 2.034 1.316 11.91 2.60 77.73 4221 3367 1.990 28.308 -2.748 1.658 4.421 0.614 72.9 800S350-97 0.1017 33 1.652 5.62 16.737 4.184 3.183 2.784 1.298 16.74 4.10 89.43* 8843 4824 5.696 38.834 -2.710 1.639 4.377 0.617 85.4 800S350-97 0.1017 50 1.652 5.62 16.737 4.184 3.183 2.784 1.298 16.74 3.79 113.34 10885 5938 5.696 38.834 -2.710 1.639 4.377 0.617 72.7 800S350-118 0.1242 33 1.997 6.79 20.041 5.010 3.168 3.295 1.285 20.04 5.01 111.44* 11341 4971 10.267 46.068 -2.682 1.624 4.345 0.619 84.6 800S350-118 0.1242 50 1.997 6.79 20.041 5.010 3.168 3.295 1.285 20.04 4.76 158.02* 16235 7115 10.267 46.068 -2.682 1.624 4.345 0.619 68.9

1000S162-43¹ 0.0451 33 0.627 2.13 8.025 1.605 3.577 0.168 0.518 7.52 1.30 25.74 836 836 0.425 3.430 -0.823 0.545 3.707 0.951 38.8 1000S162-54 0.0566 33 0.783 2.66 9.950 1.990 3.565 0.204 0.511 9.63 1.72 34.02 1661 1661 0.836 4.198 -0.812 0.538 3.692 0.952 38.6 1000S162-54 0.0566 50 0.783 2.66 9.950 1.990 3.565 0.204 0.511 9.39 1.57 47.07 1661 1661 0.836 4.198 -0.812 0.538 3.692 0.952 31.3 1000S162-68 0.0713 33 0.978 3.33 12.325 2.465 3.550 0.246 0.502 12.26 2.28 44.98 3345 3345 1.658 5.121 -0.798 0.531 3.673 0.953 38.2 1000S162-68 0.0713 50 0.978 3.33 12.325 2.465 3.550 0.246 0.502 11.98 2.15 64.51 3345 3345 1.658 5.121 -0.798 0.531 3.673 0.953 31.0 1000S162-97 0.1017 33 1.372 4.67 16.967 3.393 3.516 0.320 0.483 16.97 3.39 67.06 8843 6434 4.731 6.827 -0.768 0.514 3.631 0.955 37.5 1000S162-97 0.1017 50 1.372 4.67 16.967 3.393 3.516 0.320 0.483 16.97 3.27 97.89 9864 7177 4.731 6.827 -0.768 0.514 3.631 0.955 30.4 1000S162-118 0.1242 33 1.655 5.63 20.169 4.034 3.491 0.363 0.468 20.17 4.03 100.24* 13189 7747 8.511 7.924 -0.746 0.502 3.600 0.957 32.9

Administrator Text Box 600S300-54 0.0566 33 0.726 2.47 4.319 1.440 2.439 0.875 1.098 4.269 1.211 23.93 2739 1890 0.775 6.452 -2.299 1.372 3.527 0.575 72.8 600S300-54 0.0566 50 0.726 2.47 4.319 1.440 2.439 0.875 1.098 4.014 1.106 33.13 2823 1947 0.775 6.452 -2.299 1.372 3.527 0.575 59.0 800S300-54 0.0566 33 0.839 2.86 8.358 2.090 3.156 0.960 1.069 8.249 1.785 35.28 2091 2091 0.896 12.076 -2.073 1.271 3.924 0.721 72.2…