Atch_2_PD_180_161013_A_SHORT_Men's_and_Women's.pdf

UNITED STATES AIR FORCE ACADEMY

USAFA PD 180

SHORTS, ATHLETIC, CADET, MEN’S AND WOMEN’S

13 OCTOBER 2016

ATTACHMENT 2

13 OCT 2016

USAFA PURCHASE DESCRIPTION

SHORTS, ATHLETIC, CADET, MEN’S & WOMEN’S

1. Scope:

This purchase description covers the requirements for boxer style cadet athletic shorts.

Type I - Men’s – Just-above-the-knee length Type II - Women’s – Mid-thigh length

2. First Article:

Before production is commenced the contractor shall submit to the contracting officer, for approval, two pair athletic shorts, one of each type, size large in accordance with this purchase description.

3. Style:

The Athletic shorts shall be double-layered boxer style, four-panel construction athletic short. The shorts shall have straight hemmed legs with a 2" V-notch in the out seam hem. The waistband shall be enclosed elastic with a drawstring. The elastic shall be 1- 1/4", stitched using a four needle head. The shorts shall have two interior wallet pockets one measuring 4.5" in length and 4.5" in width and the other 4” x 3” with a tolerance of + 1/4". The pocket shall be sewn into the front inside of the waistband.

4. Logo:

The shorts shall have the USAFA Falcon Logo. The Falcon Logo shall be screen-printed in white. The Letters shall be the block style depicted in this document, 5/8" in height and placed 1/8" below the falcon (see Figure 3). The logo shall be placed on the left front leg of the Athletic shorts, facing the direction as seen on Figure 1 and Figure 3.

The dimensions of the Falcon Logo shall be as follow:

Table I. Logo Placement Inches Location

5-1/2 From (left leg) side seam 4” for men’s and 2.5” for women’s From (left leg) bottom hem

1/4" Tolerance for all placements: see Figure 1.

5. Material

The fabric shall be texollini style 4037 or equal with antimicrobial and upgraded wicking properties. This is an interlock 100% polyester fabric, 4.3 oz/sqyd.

6. Color

The color shall be Navy Blue in accordance with the Standard Color Reference of America (10th Ed.), color code #80174 or Pantone Fashion and Home Cotton Planner TCX 19-3933. All dyed components are to be of good colorfastness to withstand commercial laundering.

7. Sizes

The sizes shall be manufactured in commercial sizes:

Table II. Commercial Sizes

XS S M L XL XXL XXXL

Extra Small Small Medium Large X-Large XX-Large XXX-Large

8. Finished Measurements

The finish measurements for the Athletic shorts shall be as followed:

Table III. Finished Measurements.

Point of Measurement Tolerance XS S M L XL XXL 1.Waist Relaxed (1/2) +1/2" 11 13 15 16 18 19 2.Hip/Seat (1/2) +1/2" 19.5 21 22.5 24 25.5 27 3.Thigh (1/2) +1/2" 12 13 14 15 17 18 4a. Men’s outseam, top of band +1/2" 16.5 17 17.5 18 18.5 19.5 4b. Women’s outseam, top of band +1/2" 13.5 14 14.5 15 15.5 16.5 5a. Men’s Inseam, Type 1 +1/2" 8 8 9 9 9 10 5b. Women’s Inseam, Type 2 +1/2" 5 5 6 6 6 7 6.Front Crotch Seam +1/2" 12.5 13 13.5 14 14.5 15 7.Back Seat Seam +1/2" 14 14.5 15 15.5 16 16.5 8.Bottom Extended(1/2) +1/2" 11 12 13.5 15 15.5 16.5

1. Measure the ½ waist on a flat surface, with no stretching to the shorts.

2. The ½ hip/seat is measure 10" down from the waist across the hip/seat area parallel to the waist.

3. Thigh is measured 1" below the crotch seam, across the front of the leg.

4. The out seam is measured at the side seam from the top of waist to the top of the v-notch.

5. The inseam is measure from crotch seam to leg bottom hem edge.

6. The front crotch seam is measured front seam line from the top of the inseam to the top of the waistband.

7. The back seat seam is measured along the back seam line from the top of the inseam to the top of the waistband.

8. The ½ bottom extended is measured at the leg hem edge of the shorts.

9. Instruction Label

Standard labels shall be placed in all garments giving size, care instructions and manufacturer name. A Code 39 bar code label shall also be affixed to the individual garment package. The Code 39 bar code shall be a removable paper ticket of commercial quality with the Cadet Issue Section stock number and Code 39 bar code.

The paper ticket shall contain a short item description to include size in plain text. See Figure 2.

10. Patterns

Commercial patterns shall be used. They shall conform to the design and requirements cited in this purchase description.

11. Recycled, recovered, or environmentally preferable material:

Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs.

12. Workmanship: The finished athletic short shall conform to the quality of product established by this document. The occurrence of defects shall not exceed the contractor’s own quality assurance standards and the quality assurance standards defined by this purchase description and the technical data in the bid package.

13. Certification: The contractor shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producer’s own drawings, specifications, standards and quality assurance practices. The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

Reliance on contractor quality assurance systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract.

14. Certification of Compliance: Unless otherwise specified in the contract or purchase order, certificates of compliance shall be requested by government on all components, if the government deems necessary.

15. Inspection: The contractor shall inspect the finished products 100% for compliance with this purchase description prior to submitting to the USAFA for final inspection by 10LRS/LGRCU Quality Control personnel.

16. Final Inspection: The point of final inspection and acceptance of the finished articles shall be at the USAF Academy, using ANSI/ASQC Z1.4 and this purchase description.

17. Inspection Levels And Acceptable Quality Level

17.1. Inspection Levels: Inspection levels and acceptable quality levels (AQL’s) expressed in defects per hundred units (DHU) shall be in accordance with ANSI/ASQC Z1.4. To get an accurate understanding of defects per hundred the inspector shall follow ANSI/ASQC Z1.4 Inspection Levels and it’s instructions. To obtain a copy of ANSI/ASQC Z1.4 call: American National Standard, at 1800-854-7179 or write to:

American Society for Quality Control, 611 East Wisconsin Avenue, Milwaukee, WI 53202.

17.2. Defect List: For defect lists and finished measurement see Table III, IV and V.

17.3. AQL Levels: AQL levels and inspection levels for defects listed in Table IV and V (General and Detailed Defects, and Screen Printing Defects):

*Table IV General and Detailed Defects AQL

AQL INSPECTION

LEVEL LEVEL

Major 2.5 II Major and Minor A 15.0 II Major, Minor A And 40.0 II Minor B (combined)

**One Class 4.0 S-3

*Table IV shows the Acceptable Quality Levels and Inspection Levels for defects listed in General and Detailed Defects Table II.

**Used for Special Inspection Levels such as finished measurements

17.4. General and Detailed Defects

TABLE V. GENERAL AND DETAILED DEFECTS

MINOR

MAJOR A B

A Inferior material or workmanship defects such as distortion due to fabric manufacturing: slubs, thread breaks, holes, cuts, or any defect on the fabric attributed to the manufacturing of the fabric.

X

B Component and assembly - any component part or required operation omitted or not performed in accordance with specification. Includes but not limited to poor serging, stitching, and misalignment of components.

X

C Defects such as holes, cuts, and or tears due to workmanship qualities or fabric quality.

X

D Loose thread, ends not removed, label missing, or label miss printed.

X

E Discoloration, stains or spots due to material or workmanship

X

F Color not conforming to the color specified

G Incorrect, or illegible measurements. Inspection will be scored using the Size & Measurement Table III.

X

H Missing Instruction Label or Code 39 Bar label.

Bar code 39 not scannable and or not readable by government system

X

I Alignment of Falcon logo off centered, backwards, or misaligned.

X

J Logo not conforming to measurements on Figure 1

X

K Smudging, or misprint such as double print, ghost images, or blurry prints

L Bad ink, thick and thin areas X

18. Preservation, Packing, and Marking

The preservation, packing, and marking shall be as specified in the contract or order.

Custodian:

USAF Academy, CO 80840-8210

Preparing Activity:

Cadet Uniform Section (10LRS/LGRCU)

Reviewing Activity:

Chief, Cadet Logistics (10LRS/LGRC)

Figure 1

4”

Figure 2

Figure 3

STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL

2-3/8”

2”

1-5/8”

5/8”

INSTRUCTIONS: The purpose of this form is to solicit beneficial comments which will help achieve procurement of suitable products at reasonable cost and minimum delay, or will otherwise enhance use of the document. USAFA contractors, government activities, or manufacturers/vendors who are prospective suppliers of the product are invited to submit comments to the government.

Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual requirements.

Attach any pertinent data which may be of use in improving this document. If there are additional papers, attach to form and place both in an envelope addressed to Cadet Uniform Flight, 10 LRS/LGRCU, 2348 Sijan Dr., Suite 2B5, USAF Academy, CO 80840-8210.

DOCUMENT IDENTIFIER AND TITLE

NAME OF ORGANIZATION AND

ADDRESS

CONTRACT NUMBER

MATERIAL PROCURED UNDER A

Direct Government Contract Subcontract

1. HAS ANY PART OF THE DOCUMENT CREATED PROBLEMS OR

REQUIRED INTERPRETATION IN PROCUREMENT?

A. Give paragraph number and wording.

B. Recommendations for correcting deficiencies.

2. COMMENTS ON ANY DOCUMENT REQUIREMENT CONSIDERED TO

RIGID

3. IS THE DOCUMENT RESTRICTIVE?

4. REMARKS

SUBMITTED BY(Printed or typed name and address - Optional)

TELEPHONE NO.

DATE