3._FBNV160609-Design_Analysis.pdf

Design Analysis Report

Construct Guardian Angel AFE Shop

Davis-Monthan Air Force Base Tucson, Arizona

Prepared for

United States Department of the Air Force Air Force Installation Contracting Agency

Request for Proposal Number: FA9003-15-D-0005 Task Order: 5C01

Co nt en ts

“SAFETY PAYS” DESIGN ANALYSIS REPORT

GUARDIAN ANGEL AFE SHOP

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA TOC1

Contents SSection Page

1 General ..................................................................................................................... ...................... G1 2 Civil ....................................................................................................................... .......................... C1 3 Architectural ............................................................................................................... ................... A1 4 Structural .................................................................................................................. ..................... S1 5 Mechanical and Plumbing ..................................................................................................... ........ M1 6 Fire Protection ............................................................................................................. ................ FP1 7 Electrical .................................................................................................................. ....................... E1 8 Telecommunications .......................................................................................................... ............ T1

Appendixes

A Design Schedule B Meeting Minutes C Brand Name Justification D Submittal Register E Site Survey (Provided under separate cover) F Schedule of Bid Items (Provided under separate cover) G AF Form 3052 (Provided under separate cover)

“SAFETY PAYS” GENERAL NARRATIVE

DAVID-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA G1

1.0 General

“SAFETY PAYS” GENERAL NARRATIVE

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA G2

**SAFETY PAYS** CIVIL NARRATIVE

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA C1

2.0 Civil

2.1 Existing Conditions

2.2 Proposed Conditions

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA C2

2.3 Base Map

2.4 Site Grading

2.5 Parking and Pavement

2.6 Site Security and Fencing

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA C3

2.7 Site Utilities

Water System

Sanitary Sewer

Natural Gas

2.8 Storm Water Treatment and Permanent Erosion Control

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA C4

Storm Drainage

Temporary Erosion Control Measures

2.9 Environmental and Utility Permitting

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA C5

Permit Matrix

PERMIT TYPE DESCRIPTION AGENCY FEE

2.10 Sustainability

2.11 Codes, Standards, and Regulations

“SAFETY PAYS” ARCHITECTURAL NARRATIVE

DAVID-MONTHAN AFB

TUCSON, ARIZONADE A1

3.0 Architectural Narrative

3.1 Architectural Floor Plan

AFE Shop Floor Plan

DAVID-MONTHAN AFB

TUCSON, ARIZONADE A2

AFE Shop Code Summary

AFE Shop Accessibility

AFE Shop Bid Alternates

DAVID-MONTHAN AFB

TUCSON, ARIZONADE A3

3.2 Architectural Systems

AFE Shop:

Wall Systems

Exterior Walls

Interior Walls

Roof Systems

DAVID-MONTHAN AFB

TUCSON, ARIZONADE A4

Structural Interior Design

Interior Finishes

Floors

Ceilings

Walls

DAVID-MONTHAN AFB

TUCSON, ARIZONADE A5

Doors and Windows

Specialties

Sustainability

3.3 Codes, Standards, and Regulations

Government Design Criteria

DAVID-MONTHAN AFB

TUCSON, ARIZONADE A6

Other Design Criteria

**SAFETY PAYS** STRUCTURAL NARRATIVE

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S1

4.0 Structural

Table of Contents

Narrative

Calculations

Appendix for Structural Calculations

Introduction Guardian Angel AFE Warehouse Facility

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S2

Design Criteria, Methodology and Assumptions o o o

TUCSON, ARIZONA S3

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S4

Description of Project Structures and Facilities

Pre-Engineered Metal Building

Warehouse Foundation – Grade Slab with Thickened Perimeter

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S5

Mechanical Yard

Design Loads

TUCSON, ARIZONA S6

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S7

Design Loads continued

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S8

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S9

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S10

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S11

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S12

Load Combinations

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S13

Pre-Engineered Metal Building (PEMB) Analytical Model

N

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S14

Analytical Model

Primary Loads

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S15

Dead Load

Roof Live Load

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S16

Wind Load

TUCSON, ARIZONA S17

TUCSON, ARIZONA S18

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S19

Seismic Load

TUCSON, ARIZONA S20

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S21

Pre-Engineered Metal Building (PEMB) Column Reactions

Pre-Engineered Metal Building Foundation Anchor Rod Reinforcement Design

TUCSON, ARIZONA S22

TUCSON, ARIZONA S23

TUCSON, ARIZONA S24

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S25

Pre-Engineered Metal Building Foundation Design

TUCSON, ARIZONA S26

TUCSON, ARIZONA S27

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S28

PEMB Foundation’s Soil Bearing Pressure

TUCSON, ARIZONA S29

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S30

PEMB Foundation’s Concrete and Reinforcement Design

TUCSON, ARIZONA S31

TUCSON, ARIZONA S32

TUCSON, ARIZONA S33

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S34

Thickened Slab Edge Design

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S35

Thickened slab analysis

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S36

Grade Slab

Fork Truck

TUCSON, ARIZONA S37

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S38

Storage Racks

TUCSON, ARIZONA S39

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S40

Masonry Wall Designs

Design Parameters and Assumptions:

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S41

Metal Building Exterior Masonry Façade Wall Design

Design Parameters and Assumptions:

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S42

Masonry Screen Wall and Footing Calculations

TUCSON, ARIZONA S43

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA S44

Metal Building Exterior Masonry Façade Wall Calculations

Structural Calculations

Pre-Engineered Metal Building Column Reactions

Preliminary Fork Truck Data Sheets

Preliminary Storage Rack Data Sheets

YES

ELEVATOR

**SAFETY PAYS** MECHANICAL AND PLUMBING NARRATIVE

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M1

5.0 Mechanical and Plumbing

5.1 Design Criteria

Physical Location

Outdoor Design Conditions

(per ASHRAE Fundamentals 2013)

Indoor Design Temperature

Area Heating Cooling

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M2

Area Heating Cooling

Relative Humidity

ASHRAE Fundamentals Handbook: Ch 8, Fig. 5

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M3

Outside Air Ventilation Rate

Area Ventilation Rate

Area Exhaust Rate

Radon Systems

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M4

5.2 HVAC Systems

Proposed Heating Source

Proposed Cooling Source

Proposed HVAC System AFE Packing/Storing Building

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M5

Janitor Rooms / Toilet Rooms

Telecom Equipment / Electrical Rooms

Automatic Temperature Controls

ASHRAE 90.1 and LEED Compliance

Alternative Systems Analysis

Mechanical Systems Additional Clarification Items

5.3 Plumbing Systems

Materials and Systems

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M6

Plumbing System Equipment Domestic Potable Water Heating

Plumbing System Concepts

Water Conservation

Fixture ID Consumption

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M7

Barrier-Free Plumbing Fixtures

Plumbing Systems Additional Clarification Items

5.4 Codes, Standards, and Regulations

Standard ID Description

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M8

5.5 Calculations

Heat and Cooling Calculations

ACU-1

TUCSON, ARIZONA M9

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M10

ACU-1 Option 1

TUCSON, ARIZONA M11

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M12

Electrical Room DSS

TUCSON, ARIZONA M13

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M14

Energy Compliance

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M15

Duct Static Pressure Calculations

TUCSON, ARIZONA M16

TUCSON, ARIZONA M17

TUCSON, ARIZONA M18

TUCSON, ARIZONA M19

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M20

Equipment Selections Base Bid ACU-1

TUCSON, ARIZONA M21

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M22

Option 1 ACU-1

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M23

Natural Gas Pipe Sizing Calculation

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA M24

Minimum Water Service Size Calculation

“SAFETY PAYS” FIRE PROTECTION NARRATIVE

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA FP1

6.0 Fire Protection

6.1 Fire Suppression System Water Supply

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA FP2

6.2 Fire Suppression Systems

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA FP3

Fire Pump

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA FP4

Fire Department Access

Fire Extinguishers

6.3 Fire Alarm and Mass Notification Systems

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA FP5

6.4 Codes, Standards, and Regulations

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA FP6

F-2 Low Hazard. (NFPA 101 (Industrial Occupancy- Special Purpose)

Frontage Increase: Not needed 92,000 SF allowable per floor

UFC 3-600-01, chapters 4 and 6 Building shall be fully sprinklered per UFC 3- 600-01 requirements with a wet pipe sprinkler system.

DAVIS-MONTHAN AIR FORCE BASE

TUCSON, ARIZONA FP7

NFPA 90A

TUCSON, ARIZONA FP8

TUCSON, ARIZONA FP9

Preparers of this document certify the accuracy and completeness of the Fire Protection and Life Safety features for this project.

Bruce V Peabody P.E

Calculations

Fi re

A la rm S ys te m S ec on da ry

B at te ry

-s et

C al cu la tio n

W or ks he et G

U

AR

D

IA

N A

N G

LE

S

D

AV

IS

M

O N

TH

AN

A

FB

IT

EM

D

ES

C

R

IP

TI

O

N

ST

AN

D

B Y

C U

R R

EN

T

PE

R

U

(A M

PS

Q

TY

TO

TA

L

ST

AN

D

B Y

C U

R R

EN

T

PE

R

IT

EM

AL

AR

C U

R R

EN

T

PE

R

U

(A

PS

Q

TY

TO

TA

L

AL

R

R

EN

T

PE

R

IT

EM

FA

C U

Fi re

A la rm C on tr ol U ni t

0.

X

0.

0.

X

0.

SD

Sm ok e

D et ec to r 0.

X

0.

0.

X

0.

D

D D uc t D et ec to r

0.

X

0.

0.

X

0.

R

LY

R el ay (f ai ls af e)

0.

X

0.

0.

X

0.

R

LY

R el ay (n ot fa ils af

e) 0.

X

0.

0.

X

0.

H

S H or n-

St ro be 0.

X

0.

0.

X

0.

D

H D oo r H ol de r 0.

X

0.

0.

X

0.

AN

N An nu nc ia to r 0.

X

0.

0.

X

0.

M

S M an ua l S ta tio n

0.

X

0.

0.

X

0.

W F

W at er flo w S w itc h 0.

X

0.

0.

X

0.

TS

Ta m pe r S w itc h 0.

X

0.

0.

X

0.

0.

X

0.

0.

X

0.

0.

X

0.

0.

X

0.

R

EQ

U

IR

ED

ST

AN

D B

Y

TI

M E

(H R

S)

FP

A

-2

4.

4.

1.

5.

3.

TO

TA

L

SY

D

B Y

C U

R R

EN

T

(A M

PS

R

EQ

U

D B

Y C

AP

AC

IT

Y

(A M

P- H

O U

R S)

R

EQ

U

AL

M T

IM

E

(H O

U R

S)

FP

A

-2

4.

4.

1.

5.

3.

TO

TA

L

SY

R

R

EN

T (A

M

PS

R

EQ

U

AP

AC

IT

Y (A

M P-

H O

U R

S)

X

0.

9.

0.

X

1.

0.

R

EQ

U

D B

Y C

AP

AC

IT

Y

(A M

P- H

O U

R S)

R

EQ

U

AP

AC

IT

Y (A

M P-

H O

U R

S)

TO

TA

L C

AP

AC

IT

Y

(A M

P- H

O U

R S)

TO

TA

L C

AP

AC

IT

Y

(A M

P- H

O U

R S)

SA

FE

TY

FA

TO

R

AD

JU

B

AT

TE

R Y

C

AP

AC

IT

Y (A

M P-

H O

U R

S) 9.

0.

.1

.1

X

0%

Pr ep ar ed b y:

1.

0.

TO

TA

L

SY

ST

EM

AL

AR

M C

U R

R

EN

T (A

M

PS

TO

TA

L

SY

ST

EM

ST

AN

D

B Y

C U

R R

EN

T

(A M

PS

Pr ep ar ed fo r:

Detect Manage

Record

190-400-00, 190-401-xx, 190-407-00 Rev F 5/14/14

Monaco Enterprises, Inc.

P.O. Box 14129, Spokane Valley, WA 99214-0129; 14820 E. Sprague Ave., Spokane Valley, WA 99216-2149

Phone (509) 926-6277 Fax (509) 924-4980 E-mail service@monaco.com Web www.monaco.com

Antenna Systems

Description These antennas transmit and receive VHF signals between a transceiver and the radio frequency modem connected to the Central Receiving System.

Monaco offers omnidirectional and directional antennas:

Omnidirectional Transmit and receive in any horizontal direction; the primary antenna used with BTs, M-Panels, M Addressable Panels, and RFMs that operate in the VHF frequency range.

Directional Gold anodized Yagi antenna, transmit and receive in one direction; used to transmit VHF signals over longer distances or in areas where significant interference exists. Customer tuning required, comes with N-female connector with PL-259 female adapter, and weather seal. Includes aluminum mounting kit with stainless steel hardware.

Specifications

Omnidirectional, P/N 190-400-00

Omnidirectional, P/N 190-407-00

Omnidirectional Example

Yagi Directional Example

Mast Mount

Mast Mount

Material Stainless steel

Frequency Range 136–174 MHz

Connector Type PL-259 female

Polarization Vertical

Gain 3 dBd, 5/8 wave ground plane

RF Impedance 50 nominal

VSWR at Resonance 1.5 to 1 maximum

Wind Resistance 100 mph

Magnetic Mount

Material Stainless steel

Frequence Range 136–174 MHz

Connector Type BNC male

Polarization Vertical

Gain 3 dBd, 5/8 wave ground plane

RF Impedance 50 nominal

VSWR at Resonance 1.5 to 1 maximum

VHF Antenna, Standard 190-400-00, 190-401-xx, 190-407-00

Antenna Systems

Record

190-400-00, 190-401-xx, 190-407-00 Rev F 5/14/14

Monaco Enterprises, Inc.

P.O. Box 14129, Spokane Valley, WA 99214-0129; 14820 E. Sprague Ave., Spokane Valley, WA 99216-2149

Phone (509) 926-6277 Fax (509) 924-4980 E-mail service@monaco.com Web www.monaco.com

Antenna Systems

Directional, P/N 190-401-10

Directional, P/N 190-401-11

Directional, P/N 190-401-12

Directional, P/N 190-401-13

Material Aluminum

Frequency Range 136–142 MHz

Connector N female (RF adapter for PL-259 female)

Polarization Vertical

Power 300W

Gain 7.1 dBd

Front to Back Ratio 17 dB

RF Impedance 50 nominal

VSWR at Resonance <2:1 typical

Wind Resistance 80 mph

Horizontal Beam Width 78 degrees

Vertical Beam Width 74 degrees

Tuning See cutting chart

Material Aluminum

Frequencey Range 142–150 MHz

Connector N female (RF adapter for PL-259 female)

Polarization Vertical

Power 300W

Gain 7.1 dBd

Front to Back Ratio 17 dB

RF Impedance 50 nominal

VSWR at Resonance <2:1 typical

Wind Resistance 80 mph

Horizontal Beam Width 78 degrees

Vertical Beam Width 74 degrees

Tuning See cutting chart

Material Aluminum

Frequency Range 150–158 MHz

Connector N female (RF adapter for PL-259 female)

Polarization Vertical

Power 300W

Gain 7.1 dBd

Front to Back Ratio 17 dB

RF Impedance 50 nominal

VSWR at Resonance <2:1 typical

Wind Resistance 80 mph

Horizontal Beam Width 78 degrees

Vertical Beam Width 74 degrees

Tuning See cutting chart

Material Aluminum

Frequency Range 158–166 MHz

Connector N female (RF adapter for PL-259 female)

Polarization Vertical

Power 300W

Gain 7.1 dBd

Front to Back Ratio 17 dB

RF Impedance 50 nominal

VSWR at Resonance <2:1 typical

Wind Resistance 80 mph

Horizontal Beam Width 78 degrees

Vertical Beam Width 74 degrees

Tuning See cutting chart

Record

190-400-00, 190-401-xx, 190-407-00 Rev F 5/14/14

Monaco Enterprises, Inc.

P.O. Box 14129, Spokane Valley, WA 99214-0129; 14820 E. Sprague Ave., Spokane Valley, WA 99216-2149

Phone (509) 926-6277 Fax (509) 924-4980 E-mail service@monaco.com Web www.monaco.com

Antenna Systems

Directional, P/N 190-401-14

Ordering Information Antenna Associated Parts

Material Aluminum

Frequency Range 166–174 MHz

Connector N female (RF adapter for PL-259 female)

Polarization Vertical

Power 300W

Gain 7.1 dBd

Front to Back Ratio 17 dB

RF Impedance 50 nominal

VSWR at Resonance <2:1 typical

Wind Resistance 80 mph

Horizontal Beam Width 78 degrees

Vertical Beam Width 74 degrees

Tuning See cutting chart

Part Number Description

190-400-00 BSA-1 VHF Omnidirectional antenna, 136–174 MHz , PL-259 female connector, mounting hardware, ground clamp, coaxial cable seal.

Customer must cut to frequency.

190-407-00 BSA-6 VHF omnidirectional antenna, 136–174 MHz, magnetic-mount, portable, BNC male connector. Customer must cut to frequency.

190-401-10 BSA-2, VHF 3-element Yagi directional antenna, 136–142 MHz, N Female connector with PL-259 female adaptor, mounting hardware, coaxial cable seal. Customer must cut to frequency.

190-401-11 BSA-2, VHF 3-element Yagi directional antenna, 142–150 MHz, N Female connector with PL-259 female adaptor, mounting hardware, coaxial cable seal. Customer must cut to frequency.

190-401-12 BSA-2, VHF 3-element Yagi directional antenna, 150–158 MHz, N Female connector with PL-259 female adaptor, mounting hardware, coaxial cable seal. Customer must cut to frequency.

190-401-13 BSA-2, VHF 3-element Yagi directional antenna, 158–166 MHz, N Female connector with PL-259 female adaptor, mounting hardware, coaxial cable seal. Customer must cut to frequency.

190-401-14 BSA-2, VHF 3-element Yagi directional antenna, 166–174 MHz, N Female connector with PL-259 female adaptor, mounting hardware, coaxial cable seal. Customer must cut to frequency.

Part Number Description

199-001-00 Spare 54" antenna whip for P/N 190-400-00.

Customer must cut to frequency.

199-002-00 Spare VHF coil for P/N 190-400-00.

643-554-00 Adapter PL-259 Female to N male

164-004-03 Coaxial seal, 10" long

Part Number Description

Record

199-008-00, 199-010-00, 199-012-00, 199-014-01, 199-063-00 Rev C 06/30/15

Monaco Enterprises, Inc.

P.O. Box 14129, Spokane Valley, WA 99214-0129; 14820 E. Sprague Ave., Spokane Valley, WA 99216-2149

Phone (509) 926-6277 Fax (509) 924-4980 E-mail service@monaco.com Web www.monaco.com

Antenna Systems

Description Mounting methods depend on antenna location and desired height.

[graphic]

Tripod Mount 199-008-00

Eaves-mount Pair P/N 199-012-00

Wall-mount Pairs:

P/N 199-010-00

P/N 199-063-00

4-inch offset 1.5"dia. mast

5-inch offset 1.75"dia. mast

Antenna Tower Kit P/N 199-014-01

Pre-zinc tubing Pre-galvanized with baked alu-minum paint Heat-treated and cadmium-plated hardware Single-bolt holes

Note Conduit, weatherhead, and antennas shown but not included.

Antenna Mounting Hardware 199-008-00, 199-010-00, 199-012-00, 199-014-01, 199-063-00

Antenna Systems

Record

Monaco Enterprises, Inc.

P.O. Box 14129, Spokane Valley, WA 99214-0129; 14820 E. Sprague Ave., Spokane Valley, WA 99216-2149

Phone (509) 926-6277 Fax (509) 924-4980 E-mail service@monaco.com Web www.monaco.com

Antenna Systems

199-008-00, 199-010-00, 199-012-00, 199-014-01, 199-063-00 Rev C 06/30/15

Ordering Information Associated Parts for Tower, P/N 199-014-01 Part Number Description

199-008-00 Tripod mount, 3 ft, heavy duty, use with up to 1.75-in. dia. mast

199-010-00 Wall-mount pair, 4 in., lag bolts, use with up to 1.5-in. dia. mast

199-063-00 Wall-mount pair, 5 in. medium-duty, lag bolts, use with up to 1.75-in. dia. mast

199-012-00 Eaves-mount pair, adjustable 45-60 in. heavy-duty, lag bolts, use with up to 1.5-in. dia. mast

199-014-01 Antenna tower kit: 42-ft , 3 tower sections, top sec-tion with 1.25 in. × 5 ft mast, one 12 in. adjustable house bracket, one motor mount, all assembly hardware

Part Number Description

199-013-00 Accessory pad kit for tripod mount, three 2 in. × 0.25 in. pitch pads, six lag bolts

199-020-00 Tower section, 10 ft optional addition for P/N 199-014-01

199-021-00 Adjustable house bracket, 12 in., for tower section (P/N 199-020-00)

199-022-00 Tower hinged base for flat roof or ground founda-tion, towers must be bracketed or guyed, use with P/N 199-014-01

199-023-00 Tower nonhinged base, use with P/N 199-014-01

199-024-00 Adjustable bracket, 20–24 in., for connecting tower to building, use with P/N 199-014-01

199-025-00 Adjustable bracket, 24–33 in., for connecting tower to building, use with P/N 199-014-01

199-031-00 Spare tower-top section

Monaco Enterprises, Inc.; P.O. Box 14129, Spokane, WA 99214-0129; 14820 E. Sprague Ave, Spokane, WA 99216-2191

(509) 926-6277 (509) 924-4980 service@monaco.com www.monaco.com

Monaco Analog Addressable Panel Plus I-O-M Manual 001-353-01 Revision D 5/15

The Monaco Enterprises, Inc. (Monaco) logo and MEI are registered trademarks of Monaco. All other product names and logos in this manual are used for identification purposes only and may be trademarks or registered trademarks of their respective companies.

© 2015 by Monaco Enterprises, Inc. All rights reserved. This document contains proprietary information and is for exclusive use by Monaco customers. Use or reproduction other than by Monaco customers is expressly prohibited unless authorized in writing by Monaco.

These instructions are not intended to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation, or maintenance. If further information is needed or a particular problem arises that needs to be further described, contact Monaco.

If you have comments or suggestions on how we may improve this document, send them to:

Monaco Enterprises, Inc.; Attention: Technical Publications; P.O. Box 14129; Spokane, WA 99214-0129

Subject to the exceptions and conditions below, Monaco agrees to repair or replace any defect of material or workmanship of equipment manufactured by Monaco that develops within 12 months from the date of delivery but no more than 14 months after date of shipment from Monaco (whichever is earlier), free of charge F.O.B. Spokane, Washington. You must notify Monaco of any defect and provide either satisfactory proof of the defect or return the defective equipment to Monaco for examination at your expense in order for the equipment to be repaired or replaced under warranty.

Monaco does not provide warranty for expendable components or accessories incorporated or used with equipment manufactured by Monaco, such as batteries, visual indicators, fusing devices, etc. In addition, Monaco does not warrant components or accessories not manufactured by Monaco;

however, Monaco may help you seek adjustment from the manufacturer if the expendable components or accessories are under warranty.

You assume full responsibility for whether or not the equipment and any programs meet your specifications, capacity, capabilities, versatility, and other requirements; the installation and the condition and effectiveness of the operating environment in which the equipment and software are to function; and maintaining the equipment as specified.

The following are exceptions and conditions to this warranty:

Except as stated in this warranty, Monaco makes no warranty, expressed or implied (either in fact or by operation of law), statutory, or otherwise.

All warranties not expressly stated in this document are waived by you.

Monaco is not responsible for damage to any product from accident, unauthorized alteration, abuse, acts of God, misuse, misapplication, or inappropriate or faulty installation.

This warranty covers only those products that have been properly installed using factory-approved wiring and installation techniques.

Monaco assumes no liability for products damaged in shipment to Monaco for repair or replacement.

Monaco disclaims any liability to anyone for any damages of any kind from any cause associated with the manufacture, sale, handling, repair, maintenance, replacement, or use of its equipment.

Monaco’s liability and purchaser’s or consumer’s exclusive remedy is limited to repair or replacement of nonfunctional product at the factory.

Monaco is not liable for incidental or consequential damages, including but not limited to, installation or replacement labor costs.

Any representation and/or warranty made by any person including dealers, distributors, and representatives of Monaco that are inconsistent or in conflict with the terms of this warranty are not binding unless they are approved in writing by an Officer of Monaco.

This warranty shall be construed in accordance with and governed by the laws of the State of Washington.

This warranty gives you specific legal rights and you may also have other rights that may vary from state to state.

Before returning your equipment, contact a Monaco Customer Service Representative at (509) 926-6277 to receive a return authorization. The return authorization number must be clearly marked on any box in which the returned items are shipped and on all documents related to the return.

Monaco will not accept equipment for repair without prior Return Authorization.

Replacement and/or repair is subject to review by Monaco and will be done in accordance with this warranty. If the equipment is not under warranty or if the warranty is not in effect because of the Exceptions and Conditions, you will be asked to provide a purchase order for payment of the repair when the Return Authorization number is given. The amount of the purchase order will be based on an estimate of the cost of the repair. If a repair is not feasible, either because of cost or performance reliability of the repaired equipment, Monaco will contact you.

Monaco grants license to use its software on one computer subject to the following conditions:

Except as provided in the software license, applicable copyright laws apply to the software.

You may copy the software for the sole purpose of backup in support of its use on a single computer. All copies must include the copyright notice.

You may transfer the software and license to another party if the other party agrees to accept the terms and conditions of this agreement. If you transfer the software, you must, at the same time, transfer all copies to the same party or destroy any copies not transferred.

You may not use, copy, or transfer the software or any copy, in whole or in part, except as expressly provided in this license. If you transfer possession of any copy to another party, your license is automatically terminated.

This license is effective until terminated. You terminate the license by destroying the software and all copies in any form. License automatically terminates if you fail to comply with any term or condition of this license, in which case, you must destroy the software and all copies of it.

If you need help with your Monaco products, contact one of our Customer Service Representatives at (509) 926-6277. For other methods of contacting us, see “Contact Information” on page ii.

If the shipping cartons show evidence of rough handling, inspect the equipment carefully for shipping damage. If you find damage, notify the carrier immediately.

The Monaco Analog Addressable Panel Plus (MAAP(+)) is a narrowband transceiver/fire alarm control panel that provides a radio interface between both addressable and conventional devices and the Central Receiving System. The MAAP(+) uses Frequency Shift Key (FSK) radio protocol and is used with the D-21 Central Receiving System. MAAP(+) transceivers can operate in either the VHF or UHF frequency range. The MAAP(+) can transmit information for up to 64 Zone Position Numbers (ZPN) to the Central Receiving System, and has been enhanced to supplement the ZPN report with a “Point” status change (alarm or trouble condition) identifying the specific device associated with the alert.

The MAAP(+) operates in three different panel types: Standalone, Non-Point, and Point Reporting. Each panel is discussed below.

The MAAP(+) supports addressable sensors and modules on up to eight SLC circuits; conventional devices may be attached to optional IDC circuits available for installation in the 43" enclosure configurations. Point descriptions assigned via the Monaco Addressable Plus Planner to addressable sensors and modules, and also to conventional IDC circuits will be displayed to first responders and maintenance personnel on the MAAP(+) local LCD screen. Local actions that control output devices based on input devices conditions will operate in this mode. Sensors and modules may be grouped together into “zones” (also known as zone position numbers—ZPNs), however, these ZPNs will not be transmitted to the Monaco central.

All features provided by the standalone mode are retained with this selection. The MAAP(+) radio reporting protocol provides capability to report 16 to 64 ZPNs to either the Monaco D-21 or D-700 Enhanced Central Receiving Systems. Point information is not transmitted to Monaco Central Receiving Systems.

All features provided by the standalone mode are retained with this selection.

All devices are reported individually as “points.” Devices may also be grouped into up to 48 Zone Position Numbers (ZPN). Point information is reported to the Monaco Central Receiving System, and the MAAP(+) reports exclusively to the D-21.

The following table identifies the sections of this document with a brief description of the content of each section. Refer to “Contents” for specific information on the contents of the sections.

This document is for use with the following products: The “xx” in the part numbers refers to system frequency.

(xx = system frequency) with an AAC and one ADC in a 28-inch-high × 18-inch-wide × 3.6-inch-deep NEMA 1 enclosure, and two 12V/18 Ah batteries

(xx = system frequency) with an AAC and one ADC in a 43-inch-high × 18-inch-wide × 3.6-inch-deep NEMA 1 enclosure, and four 12V/18 Ah batteries. This enclosure supports one expansion backplane into which ZECs, UICs, or AOCs can be plugged.

1 System Description Major hardware components, circuits, ports, cables, controls, and indicators.

2 Installation How to install the MAAP(+) and its components, and wire to terminals.

3 Configuration and Testing How to configure the MAAP(+) using the LCD/keypad and the Auto Find feature. How to perform basic tests to verify the system is working.

4 Operation Common procedures performed from the MAAP(+). Descriptions of top-level menu items and alarm and trouble conditions.

5 Maintenance Scheduled maintenance, and instructions for replacing components.

6 Troubleshooting Procedures Instructions for troubleshooting.

Appendix A Glossary

Appendix B Specifications

Appendix C MAAP(+) Menu Structure

Appendix D Spare Parts

Appendix E LCD Messages

Appendix F Wiring Diagrams

Index Index

(xx = system frequency) with an AAC and one ADC in a 60-inch-high × 18-inch-wide × 3.6-inch-deep enclosure, and four 12V/18 Ah batteries. This enclosure supports three expansion backplanes into which ZECs, UICs, or AOCs can be plugged.

(xx = system frequency) with an AAC and one ADC in a 28-inch-high × 18-inch-wide × 3.6-inch-deep NEMA 1 enclosure, and two 12V/18 Ah batteries.

(xx = system frequency) with an AAC and one ADC in a 43-inch-high × 18-inch-wide × 3.6-inch-deep enclosure, and four 12V/18 Ah batteries. This enclosure supports one expansion backplane into which ZECs, UICs, or AOCs can be plugged.

(xx = system frequency) with an AAC and one ADC in a 24-inch-high × 24-inch-wide × 8-inch-deep NEMA 4X stainless steel enclosure, and two 12V/18 Ah batteries.

(xx = system frequency) with an AAC and one ADC in a 24-inch-high × 24-inch-wide × 8-inch-deep NEMA 3R enclosure, and two 12V/18 Ah batteries.

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Panel Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 MAAP(+) Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 Electronic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 Power Supply and RF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Analog Addressable Controller (AAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14 AAC Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14 AAC Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15 AAC Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15 AAC Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15

Analog Driver Card (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16 ADC Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Expansion Backplane. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17 Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17 Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17 Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17

Devices Connected to Signaling Line Circuits (SLC) . . . . . . . . . . . . . . . . . . . . . . . 1-18 Optional External Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20

Alarm and Trouble Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20 Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20

Visible Notification of Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20 Alarm Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20 Reporting of Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22 Acknowledging and Clearing Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22 Number of Alarms Stored . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22 Alarms are the Highest Priority. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22

Troubles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23 Visible Notification of Troubles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23 Trouble Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23 Reporting of Troubles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25 Acknowledging and Clearing Troubles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25 Number of Troubles Stored. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26 Priority of Troubles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26

Trouble and Alarm List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26 Panel Trouble Supervision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26

Packaging Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Warnings and Caution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Installing the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Mounting the Enclosure and Installing the Components . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Installing an Analog Driver Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Installing and Removing ADC Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13 Installing an Expansion Backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Addressing an Expansion Backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 Selecting Class A or B for the IDC and NAC Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17 Connecting Wires to Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17 Wiring to the Electronic Assembly for IDC and NAC Operation . . . . . . . . . . . . . . . . . 2-18

Wiring Auxiliary Input Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18 Wiring Onboard IDCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

Determining the Number of Loop-Powered Sensors Supported by an IDC . . . 2-20 Wiring NACs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

Determining the Number of Devices Supported by a NAC . . . . . . . . . . . . . . . 2-22 Wiring the Auxiliary Output Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 Wiring K1 and K2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23

Wiring to the Expansion Backplane for IDC Operation . . . . . . . . . . . . . . . . . . . . . . . . . 2-23 Wiring Expansion IDCs Provided by ZECs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24 Wiring Expansion Auxiliary Output Circuits Provided by AOCs . . . . . . . . . . . . . . 2-26

Wiring to the AAC for SLC Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26 Device Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28 SLC Design Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28

Verifying an SLC Will Support the Planned Design . . . . . . . . . . . . . . . . . . . . . 2-29 Circuit Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30

Isolator Devices Per SLC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30 SLC Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30

Applying Power to the MAAP(+). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31 Determining Panel Current Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33 Determining Standby Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33 Connecting a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34

Configuring the MAAP(+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Configuring a New MAAP(+) Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Prepare the MAAP(+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Using Auto Find to Detect Addressable Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Addressable Device Defaults Set by Auto Find . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Configuring Class of NACs (Bells) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11 Defining Critical Communication Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

Defining the Transceiver Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

Critical Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17 Testing the MAAP(+). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

MAAP(+) Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18 Measure Forward and Reflected Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19 Calculate Voltage Standing Wave Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19 Test Transceiver Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20 Test the Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Available User Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Using the Keypad or Terminal Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Display Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Normal Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Alarm/Trouble Silence Pending Mode and Alarm/Trouble Display Mode. . . . . . . 4-4

LCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Planner Terminal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Before Beginning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Using Terminal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Alarm Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Supervisory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Detector Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

When Not to Use Detector Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Tamper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Alarms Associated with AUX OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14

Waterflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Positive Alarm Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Master Box Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15

Alarm Indication Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Trouble Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Trouble Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17 Zone Trouble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17 Device Trouble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17 System Trouble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Listing Troubles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 Returning the MAAP(+) to Normal Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 Troubles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

Communication with the Central Receiving System . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Transmission Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 Transmission Strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

MAAP(+) Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Maintenance Troubles and Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Scheduled Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Daily Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Monthly Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Semiannual Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Annual Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Test Equipment and Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Measurement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Component Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Replacing the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Replacing the Electronic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Replacing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 Replacing the Central Processing Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 Replacing the RF Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 Replacing the LCD/keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13 Replacing the Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14 Replacing the EPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14 Replacing the AAC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16 Replacing the Expansion Backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18

Troubleshooting Data Transfer Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Troubleshooting the MAAP(+). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Possible Transceiver Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 SLC Troubles and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2 Supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4 Inputs/Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6

Radio (Receiver/Transmitter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9 Switches, Jumpers, Keys, and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9 Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10 Enclosures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10 Typical Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10

LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2 Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Trouble Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2 Component Identifiers for Items in Alarm or Trouble . . . . . . . . . . . . . . . . . . . . . . . . . . E-5

Electronic Assembly Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-2 Expansion Backplane Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-3 SLC Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-4

Figure 1-1 MAAP(+) Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Figure 1-2 Front View of Electronic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 Figure 1-3 Electronic Assembly Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10 Figure 1-4 Power Supply with RF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13 Figure 1-5 AAC Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14 Figure 1-6 Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16 Figure 1-7 Expansion Backplane . . . . . . . . . . . . .