FA465915R0015_Drawings.pdf

LAD Project No.

A R C H I T E C T U R E

EST. 1915

E N G I N E E R I N G

I N T E R I O R S

P L A N N I N G

ATLANTA

AUSTIN

DALLAS

DENVER

FORT WORTH

HONG KONG

HONOLULU

HOUSTON

LAS VEGAS

LOS ANGELES

MIAMI

MINNEAPOLIS

OMAHA

PHOENIX

SAN ANTONIO

WACO

WASHINGTON, DC

GFAFB Project No. JFSD201516

Sheet ______ of __25__

JFSD201516 Repair HVAC Controls/Equipment - 69 RG & 319 ABW Building 607

GRAND FORKS AIR FORCE BASE

575 TUSKEGEE AIRMEN BLVD

GRAND FORKS AFB, ND 58205-6436

Grand Forks Air Force Base

3-20-2015

100% SUBMITTAL

021-10085-012

Stephen W. Nelson

03/18/2015 14186

Print Name:

Signature:

Date: License #

I hereby certify that this plan, specification, or report was prepared by me or under my direct supervision and that I am a duly Licensed Professional Engineer under the laws of the State of Minnesota.

ELECTRICAL

Print Name:

Signature:

Date: License #

I hereby certify that this plan, specification, or report was prepared by me or under my direct supervision and that I am a duly Licensed Professional Engineer under the laws of the State of Illinois.

MECHANICAL

Joseph W. Reister

03/18/2015 062-043516

1. ALL DUCTWORK IS SHOWN IN SCHEMATIC FORM. NOT ALL DUCT

RISES AND DROPS ARE SHOWN. PROVIDE OFFSETS AS REQUIRED

TO MEET SPACE REQUIREMENTS AND TO AVOID INTERFERENCE

WITH OTHER TRADES. ROUTE ALL DUCTWORK AS HIGH AS

POSSIBLE.

2. COORDINATE FINAL LOCATIONS OF NEW DUCTWORK AND HVAC

EQUIPMENT WITH EXISTING SYSTEMS, STRUCTURE, LIGHTING,

ARCHITECTURAL ELEMENTS, PIPING AND SPRINKLERS.

3. COORDINATE DIFFUSER, REGISTER AND GRILLE LOCATIONS WITH

REFLECTED CEILING PLAN AND ELECTRICAL LIGHTING PLAN.

4. PROVIDE LONG RADIUS DUCT ELBOWS WHEREVER POSSIBLE AND

PROVIDE SQUARE ELBOWS WITH TURNING VANES PER SMACNA.

5. LIMIT DUCT TRANSITION ANGLES TO 1 IN 7 OR 15 DEGREES. LIMIT

EQUIPMENT CONNECTION TRANSITIONS TO 30 DEGREES MAXIMUM.

TRANSITION DUCTWORK AS REQUIRED FOR FINAL EQUIPMENT

CONNECTIONS.

6. FOR BRANCH DUCT TAPS, PROVIDE CONICAL FITTINGS AT ROUND

OR FLAT OVAL TAKEOFFS AND 45 DEGREE ENTRY FITTINGS AT

RECTANGULAR TAKEOFFS.

7. PROVIDE MANUAL VOLUME DAMPERS AT BRANCH DUCT TAPS FOR

EACH SUPPLY AIR OUTLET AND EACH EXHAUST, RETURN AND

RELIEF AIR INLET OR PROVIDE VOLUME DAMPERS AT GRILLES,

REGISTERS OR DIFFUSERS, AS INDICATED.

8. PROVIDE SLEEVES AT EACH PENETRATION OF FIRE AND SMOKE

RATED ASSEMBLIES AND SEAL WITH FLANGES AND INTUMESCENT

MATERIAL, AS REQUIRED.

9. DO NOT LOCATE DUCTWORK, PIPING OR MECHANICAL EQUIPMENT

ABOVE ANY ELECTRICAL EQUIPMENT.

10. ALL DUCT SIZES ARE CLEAR INSIDE DIMENSIONS.

11. PROVIDE FACTORY INSULATED FLEX DUCTS AS INDICATED,

MINIMUM 36” AND MAXIMUM 72” LONG, SAME SIZE AS OUTLET OR

INLET NECK SIZE. CONNECT FLEXIBLE DUCTS WITH DRAWBANDS

AND TAPE AT EACH END. DO NOT INSTALL FLEXIBLE CONNECTIONS

ABOVE INACCESSIBLE CEILINGS.

12. FABRICATE AND SUPPORT ALL DUCTWORK IN ACCORDANCE WITH

SMACNA HVAC DUCT CONSTRUCTION STANDARDS – METAL AND

FLEXIBLE – CURRENT VERSION.

13. PROVIDE ADEQUATE CLEARANCE FOR INSULATION IN HANGERS,

FROM STRUCTURE AND FROM EQUIPMENT.

14. PROVIDE ROUGH-INS AND CONNECTIONS TO EQUIPMENT PROVIDED

BY OTHERS, AS INDICATED.

15. SEAL ALL DUCTWORK TO SMACNA SEAL CLASS A, UNLESS

INDICATED OTHERWISE.

16. CONSTRUCT ROUND, FLAT OVAL AND RECTANGULAR SUPPLY AIR

DUCTWORK TO +2 INCH W.G. SMACNA PRESSURE CLASSIFICATION,

UNLESS INDICATED OTHERWISE.

17. CONSTRUCT ROUND, FLAT OVAL AND RECTANGULAR EXHAUST,

RETURN AND RELIEF AIR DUCTWORK TO -2 INCH W.G. SMACNA

PRESSURE CLASSIFICATION, UNLESS INDICATED OTHERWISE.

18. WHERE ANY AUTOMATIC DAMPER, SMOKE DAMPER OR FIRE DAMPER

CANNOT BE ACCESSED OR VIEWED THROUGH LAY-IN CEILINGS OR

OTHER CONVENIENT MEANS, PROVIDE A MINIMUM 24 INCH X 24 INCH

ARCHITECTURALLY ACCEPTABLE RATED ACCESS PANEL AT EACH

INACCESSIBLE LOCATION.

19. CONNECT DUCT AND EQUIPMENT HANGERS TO TOP CHORD OF ROOF

JOISTS, BEAM FLANGES OR CONCRETE FLOOR DECK, BY APPROVED

MEANS.

DUCTWORK NOTESGENERAL/DEMOLITION NOTES

1. CONCRETE CURBS AND PADS ARE PROVIDED BY OTHERS.

COORDINATE EXACT SIZES AND LOCATIONS.

2. LOUVERS ARE PROVIDED BY OTHERS. COORDINATE EXACT SIZES

AND LOCATIONS.

3. MAINTAIN EXISTING SERVICES IN OPERATION AT ALL TIMES, EXCEPT

AS SPECIFICALLY INDICATED.

4. COORDINATE SHUTDOWNS OF, CONNECTIONS TO, TESTING AND

CLEANING OF EXISTING SYSTEMS WITH THE OWNER TO MINIMIZE

DISRUPTION AND DOWNTIME.

5. REMOVE LAY-IN CEILING TILES AND GRID AS REQUIRED FOR NEW

SYSTEMS INSTALLATION AND CONNECTIONS TO EXISTING SYSTEMS.

INSTALL CEILING TILES WHEN WORK IS COMPLETE, REPLACE ANY

DAMAGED CEILING TILES AND REPAIR ANY DAMAGED CEILING GRID.

6. IDENTIFY AND COORDINATE ALL NEW PENETRATIONS OF EXISTING

FLOORS AND PARTITIONS. PATCH, REPAIR AND FIRESTOP ALL NEW

PENETRATIONS REQUIRED FOR MECHANICAL WORK.

1. ALL PIPING IS SHOWN IN SCHEMATIC FORM. NOT ALL PIPING RISES

AND DROPS ARE SHOWN. PROVIDE OFFSETS AS REQUIRED TO

MEET SPACE REQUIREMENTS AND TO AVOID INTERFERENCE WITH

OTHER TRADES. ROUTE ALL PIPING AS HIGH AS POSSIBLE.

2. INSTALL PIPING WITH ADEQUATE SLOPE FOR EACH SYSTEM, AS

REQUIRED.

3. COORDINATE FINAL LOCATIONS OF NEW PIPING AND HVAC

EQUIPMENT WITH EXISTING SYSTEMS, STRUCTURE, LIGHTING,

ARCHITECTURAL ELEMENTS, DUCTWORK, PIPING AND SPRINKLERS.

4. REFER TO PIPING DETAILS FOR PIPING ACCESSORIES AND FINAL

CONNECTIONS TO HVAC EQUIPMENT AND TERMINAL UNITS.

TRANSITION PIPING AS REQUIRED FOR FINAL EQUIPMENT

CONNECTIONS, MINIMUM ¾” IPS PIPE SIZE.

5. PROVIDE MANUAL AIR VENTS WITH CAPPED HOSE END

CONNECTIONS AT THE TOP OF EACH RISER AND AT ALL HIGH POINTS

IN EACH PRESSURE PIPING SYSTEM.

6. PROVIDE DRAIN VALVES WITH CAPPED HOSE END CONNECTIONS AT

THE BOTTOM OF EACH RISER AND AT ALL LOW POINTS IN EACH

PRESSURE PIPING SYSTEM.

7. PROVIDE SLEEVES AT EACH PENETRATION OF FIRE AND SMOKE

RATED ASSEMBLIES AND SEAL WITH INTUMESCENT MATERIAL.

8. PROVIDE ADEQUATE CLEARANCE FOR INSULATION IN HANGERS,

FROM STRUCTURE AND FROM EQUIPMENT.

9. INSTALL PIPING TO ALLOW FOR EXPANSION AND CONTRACTION AND

TO MINIMIZE STRESSING OF EQUIPMENT CONNECTIONS.

10. PROVIDE ROUGH-INS AND CONNECTIONS TO EQUIPMENT PROVIDED

BY OTHERS, AS INDICATED.

11. WHERE ANY CONTROL VALVE, MANUAL VALVE, DRAIN OR AIR VENT

CANNOT BE ACCESSED OR VIEWED THROUGH LAY-IN CEILINGS OR

OTHER CONVENIENT MEANS, PROVIDE A MINIMUM 24 INCH X 24 INCH

ARCHITECTURALLY ACCEPTABLE RATED ACCESS PANEL AT EACH

INACCESSIBLE LOCATION.

12. CONNECT PIPE AND EQUIPMENT HANGERS TO TOP CHORD OF ROOF

JOISTS, BEAM FLANGES OR CONCRETE FLOOR DECK, BY APPROVED

MEANS.

13. SIZE AND SLOPE REFRIGERANT PIPING AS INDICATED, OR IN

ACCORDANCE WITH MANUFACTURER GUIDELINES.

14. FOR BELOW GRADE PIPING FOR INFLOOR HEATING, BELOW FLOOR

HEATING AND GROUND SOURCE WELL FIELDS, REFER TO

MANUFACTURER GUIDELINES FOR MATERIAL HANDLING AND

INSTALLATION. PRESSURE TEST ALL INFLOOR HEATING, BELOW

FLOOR HEATING AND GROUND SOURCE WELL FIELD PIPING PRIOR

TO, AND DURING, BACKFILLING, COMPACTION AND CONCRETE

INSTALLATION.

PIPING NOTES

LEO A DALY Company 2014

A

B

C

D

A

B

C

D

2 3 4 5

P L

A N

N I N

G A

R C

H I T

E C

T U

R E

E N

G I N

E E

R I N

G I N

T E

R I O

R S

ES

T

S ec o n d A ve n u e

So u th

Su it e

M in n ea p o li s, M N

-2

U

SA

T el

-3

-8

F ax

-3

-4

G R

A N

D F

O R

K S

A F

B , N

D

C O

N T

R A

C T

S E

LE

M

E N

T

C

IV

IL

E

N G

IN

E

E R

S Q

U A

D R

O N

A

IR

M O

B

IL

IT

Y

C O

M M

A N

D

D E

P A

R T

M E

N T

O F

T H

E A

IR

F

O R

C E

P R

O

JE

C T

N U

M B

E R

: G F

A F

B J

F S

D

LA

D

P

LO

T S

C A

LE

P

LO

T D

A T

E

C H

K B

Y

D W

N B

Y

D E

S

IG

N E

D B

Y

F

IL

E N

A M

E

D A

T E

1 2 3 4 5

Sheet of 25

A S

IN

D

IC

A

T E

D

/1

/2

:1

:2

P

M

G E

N E

R A

L N

O T

E S

, S H

E E

T

IN

D E

X

K E

Y N

O T

E S

JF

S

D

R ep ai r

H V

A C

C on tr ol s/ E qu ip m en t -

R

G

A B

W B ui ld in g

1-

5-

3-

-2

B

LB

N R

W

N

JB

100% SUBMITTAL

G-001

3-

-2

JF

S

D _G

-0

SHEET INDEX

SHEET

SEQUENCE

NUMBER 3

D E

S

IG

N S

U B

M

IT

T A

L

IS

S U

E D

-0

-2

D E

S

IG

N S

U B

M

IT

T

U

E D

-1

-2

D E

S

IG

N S

U B

M

IT

T

U

E D

-2

-2

D E

S

IG

N S

U B

M

IT

T

U

E D

-0

-0

SHEET NO. SHEET NAME

01 - GENERAL

1 G-000 COVER X X X X

2 G-001 GENERAL NOTES, SHEET INDEX & KEYNOTES X X X X

3 G-002 SYMBOLS AND ABBRIVATIONS X X X X

4 G-101 VICINITY MAP X X X X

5 G-501 GENERAL DETAILS X X X X

6 G-601 GENERAL SCHEDULES AND SECTIONS X X X X

06 - BLDG 607

7 607-M-101 BUILDING 607 - OVERALL PLAN X X X X

8 607-M-401 ENLARGED PLANS B607 AHU-16 AND ROOM 119 X X X X

9 607-M-402 ENLARGED PLANS B607 AHU-19 AND AHU-20 X X X X

10 607-M-610 CONTROL SCHEMATICS B607 AHU-1 ROOF X X X X

11 607-M-611 CONTROL SCHEMATICS B607 AHU-1 SOUTH X X X X

12 607-M-612 CONTROL SCHEMATICS B607 AHU-2 ROOF X X X X

13 607-M-613 CONTROL SCHEMATICS B607 AHU-2 FLOOR X X X X

14 607-M-614 CONTROL SCHEMATICS B607 AHU-6 X X X X

15 607-M-615 CONTROL SCHEMATICS B607 AHU-8 NORTH X X X X

16 607-M-616 CONTROL SCHEMATICS B607 AHU-8 SOUTH X X X X

17 607-M-617 CONTROL SCHEMATICS B607 AHU-13 X X X X

18 607-M-618 CONTROL SCHEMATICS B607 AHU-15 X X X X

19 607-M-619 CONTROL SCHEMATICS B607 AHU-16 X X X X

20 607-M-620 CONTROL SCHEMATICS B607 AHU-19 X X X X

21 607-M-621 CONTROL SCHEMATICS B607 AHU-20 X X X X

22 607-M-622 CONTROL SCHEMATICS B607 HVU-2 X X X X

23 607-M-623 CONTROL SCHEMATICS B607 HVU-5 X X X X

24 607-M-624 CONTROL SCHEMATICS B607 INTEL HVAC X X X X

25 607-E-401 ELECTRICAL PLAN X X

CONTROLS KEYNOTE LEGEND

C01 ACTUATOR AND DAMPER. PROVIDE NEW DDC ACTUATOR. DAMPER TO REMAIN.

C02 ACTUATOR AND DAMPER TO REMAIN.

C03 LINKED ACTUATOR AND DAMPER. PROVIDE NEW DDC ACTUATOR. DAMPER TO

REMAIN.

C04 LINKED ACTUATOR AND DAMPER TO REMAIN.

C05 MOTORIZED 3-WAY VALVE. PROVIDE NEW VALVE BODY AND DDC ACTUATOR.

C06 MOTORIZED 3-WAY VALVE AND ACTUATOR TO REMAIN.

C07 PROVIDE NEW FILTER DIFFERENTIAL PRESSURE SENSOR

C08 PROVIDE NEW DUCT MOUNTED, PROBE TYPE TEMPERATURE SENSOR

C09 PROVIDE NEW DUCT MOUNTED, AVERAGING TYPE CAPILARY TUBE TEMPERATURE

SENSOR

C10 PROVIDE NEW UNIT MOUNTED, PROBE TYPE TEMPERATURE SENSOR

C11 PROVIDE NEW UNIT MOUNTED, AVERAGING TYPE CAPILARY TUBE TEMPERATURE

SENSOR

C12 PROVIDE NEW UNIT MOUNTED FREEZE STAT

C13 NEW WALL MOUNTED ROOM TEMPERATURE SENSOR. INCLUDE LCD DISPLAY.

OCCUPANCY OVERRIDE AND SETPOINT ADJUSTMENT

C14 PROVIDE NEW DUCT MOUNTED STATIC PRESSURE SENSOR

C15 EXISTING DUCT MOUNTED SMOKE DETECTOR TO REMAIN

C16 PROVIDE NEW VARIABLE FREQUENCY DRIVE. REMOVE ANY/ALL INLET VANE

DAMPERS.

C17 EXISTING VARIABLE FREQUENCY DRIVE TO REMAIN

C18 EXISTING PREFILTERS

C19 PROVIDE NEW ZONE/ZONE PRESSURE DIFFERENTIAL SENSOR

C21 EXISTING PUMP AND PUMP PRESSURE DIFFERENTIAL SENSOR TO REMAIN

C22 PROVIDE NEW AIR FLOW MEASURING STATION

C23 PROVIDE NEW DUCT MOUNTED HUMIDITY SENSOR

C24 PROVIDE NEW DUCT MOUNTED CO2 SENSOR

C25 PROVIDE NEW DUCT MOUNTED STATIC PRESSURE SENSOR

DEMO KEYNOTE LEGEND

D02 REMOVE CONDENSING UNIT AND ASSOCIATED CONTROLS AND REFRIGERANT

PIPING. SEE SPEC FOR REFRIGERANT RECOVERY REQUIREMENTS.

D04 REMOVE AHU, SUPPLY AND OUTSIDE AIR DUCT CONNECTIONS, CHILLED WATER

PIPING CONNECTIONS AND CONTROLS. CAP CHILLED WATER PIPING RUNOUTS FOR

RECONNECTION.

D05 REMOVE AHU, SUPPLY AND RETURN DUCT CONNECTIONS, DX PIPING, CONDENSATE

PIPING CONNECTION AND CONTROLS. CAP CONDENSATE PIPING FOR

RECONNECTION.

D06 REMOVE AHU, SUPPLY AND RETURN DUCT CONNECTIONS, DX PIPING, HEATING

WATER PIPING CONNECTIONS AND CONTROLS. CAP HEATING WATER PIPING FOR

RECONNECTION.

D07 REMOVE AHU, SUPPLY, RETURN AND OUTSIDE AIR DUCT CONNECTIONS, DX PIPING,

HEATING WATER PIPING CONNECTIONS AND CONTROLS. CAP HEATING WATER

PIPING FOR RECONNECTION.

MECHANICAL KEYNOTE LEGEND

M01 REMOVE ALL EXISTING PNEUMATIC CONTROLS AND REPLACE WITH DDC CONTROL

SYSTEM INTERFACED WITH THE CAMPUS EMCS. REPROGRAM AIR HANDLER

CONTROL SEQUENCES. REFER TO AIR HANDLING UNIT CONTROL SCHEMATICS FOR

ADDITIONAL INFORMATION.

M02 REBALANCE AIR HANDLING UNIT SUPPLY, RETURN, AND OUTSIDE AIR FLOW TO CFM

INDICATED ON AIR HANDLING UNIT CONTROL SCHEMATICS.

M03 ADJUST ALL DAMPER LINKAGES TO ENSURE DAMPER OPERATES PROPERLY

THROUGH ITS FULL RANGE OF MOTION.

M04 REMOVE EXISTING DRAIN PAN AND REPLACE WITH NEW, INSULATED, DOUBLE

SLOPED STAINLESS STEEL DRAIN PAN.

M05 REPAINT UNIT CASING WITH WEATHER AND UV RESISTANT ENAMEL BASED PAINT.

REFER TO PAINT SPECIFICATION FOR ADDITIONAL INFORMATION.

M06 REMOVE STEEL CURB FLASHING AND REPLACE WITH COATED ALUMINUM FLASHING.

M07 REPROGRAM AIR HANDLER CONTROL SEQUENCES. REFER TO AIR HANDLING UNIT

CONTROL SCHEMATICS FOR ADDITIONAL INFORMATION.

M08 PROVIDE NEW OSHA APPROVED BELT GUARD.

M09 REMOVE AND REPLACE AIR HANDLING UNIT. REFER TO ENLARGED PLANS FOR

ADDITIONAL INFORMATION.

M10 REPAIR AND RE-SEAL INTERIOR AIR HANDLING UNIT INSULATION.

M16 INSTALL NEW CONDENSING UNIT ON NEW ROOF CURBS. ROUTE REFRIGERANT

PIPING ON ROOF AND DOWN THRU EXISTING ROOF OPENING.

M17 NEW AHU, ENLARGE EQUIPMENT PAD AS REQUIRED TO ACCOMMODATE UNIT,

RECONNECT SUPPLY AND OUTSIDE AIR DUCTS, RECONNECT CHILLED WATER

PIPING.

M18 NEW AHU HUNG FROM STRUCTURE, RECONNECT SUPPLY AND RETURN DUCTS,

ROUTE DX PIPING FROM UNIT TO CONDENSING UNIT ON ROOF, CONNECT

CONDENSATE PIPE TO EXISTING.

M19 NEW AHU, ENLARGE EQUIPMENT PAD AS REQUIRED TO ACCOMMODATE UNIT,

RECONNECT SUPPLY AND RETURN DUCTS, ROUTE DX PIPING FROM UNIT TO

CONDENSING UNIT ON ROOF, RECONNECT HEATING WATER PIPING.

M20 NEW AHU, ENLARGE EQUIPMENT PAD AS REQUIRED TO ACCOMMODATE UNIT,

RECONNECT SUPPLY, RETURN AND OUTSIDE AIR DUCTS, ROUTE DX PIPING FROM

UNIT TO CONDENSING UNIT ON ROOF, RECONNECT HEATING WATER PIPING.

M22 REMOVE FAN INLET GUIDE VANES.

ENVIRONMENTAL AWARENESS

Both an Asbestos and Lead Based Paint Surveys were performed. Refer to the project specifications section 00 31 26 and 028214 for additional information. Asbestos was detected in the samples collected from some of the existing buildings. If suspected asbestos containing materials (SACM) are encountered during demolition activities during the renovation, the Contractor shall immediately notify the Government Construction Representitive and cease work in proximity to the SACM. The Government Construction Representative will arrange for the testing and removal of any asbestos containing materials (ACM). If asbestos containing materials will be disturbed as part of the renovation project the asbestos containing materials must be removed by an EPA licensed asbestos abatement contractor.

N O

D

ES

C

R

IP

T

IO

N D

A T E

AIR ADMITTANCE VALVE

AIR COMPRESSOR

AIR COOLED CONDENSING UNIT

ACTUAL CUBIC FEET PER MINUTE

AIR CONDITIONING UNIT

AREA DRAIN (AIR DRYER)

AIR FILTER

ABOVE FINISHED FLOOR

AIR FLOW MEASURING STATION

AIR HANDLING UNIT

AIR TO AIR HEAT EXCHANGER

ALTERNATE

ACCESS PANEL

AIR PRESSURE DROP

AIR SEPARATOR

BACKDRAFT DAMPER

BELOW FINISHED FLOOR

BACK FLOW PREVENTER

BRAKE HORSEPOWER

BY OWNER

BOTTOM OF DUCT

BUFFER TANK

BACKWATER VALVE

COOLING (CHILLED WATER) COIL

CONDENSATE DRAIN

CUBIC FEET PER HOUR

CUBIC FEET PER MINUTE

CAST IRON

CEILING

CENTER LINE

CARBON MONOXIDE (CLEANOUT)

COMBINATION

COMPRESSOR

CONCRETE

CONDENSATE (CONDENSER)

CONNECTION

CONTINUOUS (CONTINUED)

CONTRACTOR

COMPUTER ROOM AIR COND. UNIT

CLINICAL SERVICE SINK

CABINET UNIT HEATER

DECIBEL (DRY BULB)

DIRECT DIGITAL CONTROL (PANEL)

DRINKING FOUNTAIN

DRY FLUID COOLER

DRY FIRE SPRINKLER

DIFFUSER

DISCHARGE

DOWN

DOWNSPOUT

DRY STAND PIPE

DISH WASHER

DIRECT EXPANSION (COOL'G COIL)

EXHAUST AIR (EACH)

ENTERING AIR TEMPERATURE

EXHAUST FAN

ELEVATION

EQUIPMENT

ENERGY RECOVERY VENTILATOR

EM. EYEWASH/SHOWER

EXTERNAL STATIC PRESSURE

EXPANSION TANK

EVAPORATOR

EMERGENCY EYEWASH

ELECTRIC WATER COOLER

ELECTRIC WATER HEATER

ENTERING WATER TEMPERATURE

EXHAUST

EXPANSION

EXTERNAL

FLOW CONTROL VALVE

FIRE DAMPER (FLOOR DRAIN)

FIRE DEPARTMENT CONNECTION

FIRE DEPARTMENT VALVE

FIRE MAIN

FIRE PROTECTION

FEET PER MINUTE

FINS PER INCH

FEET PER SECOND

FACE VELOCITY

GAUGE

GALVANIZE

GRAVITY BACK DRAFT DAMPER

GENERAL

GLYCOL FEEDER

GALLONS PER HOUR

GALLONS PER MINUTE

GRILLE

GROUND SOURCE HEAT PUMP

GRAVITY VENTILATOR

GAS WATER HEATER

HUMIDIFIER

HEATING CONVECTOR (COIL)

HEAD

HANDICAPPED

HIGH PRESSURE (HORSEPOWER)

HEAT PUMP WATER HEATER

HEATING, VENTILATION & AIR COND.

HEAT WHEEL (HOT, HEAT'G WATER)

HEAT EXCHANGER

HOSE BIBB

HOSE REEL

AAV

AC

ACCU

ACFM

ACU

AD

AF

AFF

AFMS

AHU

AHX

ALT

AP

APD

AS

BDD

BFF

BFP

BHP

BO

BOD

BT

BWV

CC

CD

CFH

CFM

CI

CLG

CL

CO

COMB

COMP

CONC

COND

CONN

CONT

CONTR

CRAC

CSS

CUH

DB

DDC

DF

DFC

DFS

DIFF

DISH

DN

DS

DSP

DW

DX

EA,E/A

EAT

EF

EL

EQ

ERV

ES

ESP

ET

EVAP

EW

EWC

EWH

EWT

EXH

EXP

EXT

FCV

FD

FDC

FDV

FM

FP

FPM

FPI

FPS

FV

GA

GALV

GBD

GEN

GF

GPH

GPM

GR

GSHP

GV

GWH

H

HC

HD

HDCP

HP

HPWH

HVAC

HW

HX

HB

HR

CONDENSATE, CONDENSER DRAIN

HEATING WATER SUPPLY

HEATING WATER RETURN

D

HWS

HWR

ABBREVIATIONSPIPING ANNOTATION DUCT SYMBOLSPIPING & PLUMBING SYMBOLS

DOUBLE LINE DUCTWORK

SUPPLY RETURN

EXHAUST ROUND

SINGLE LINE DUCTWORK

DUCT RISES,

DROPS AND

SECTIONS

SUPPLY RETURN

DESCRIPTION SYMBOLSYMBOL

RISE (R) OR DROP (D) IN DUCTWORK

TRANSITION

CONCENTRIC REDUCER (SQUARE TO ROUND)

MOTORIZED DAMPER

FIRE, SMOKE AND FIRE/SMOKE DAMPER

MANUAL VOLUME DAMPER AND

BACKDRAFT DAMPER

MITERED ELBOW WITH TURNING VANES

LONG SWEEP RADIUS ELBOW

BRANCH TAKE-OFFS OF A

RECTANGULAR MAIN WITH MANUAL

VOLUME DAMPERS

BRANCH TAKE-OFFS OF A ROUND MAIN

WITH MANUAL VOLUME DAMPERS

FLEXIBLE DUCT WITH DIFFUSER

R D

24/12 18/16 24/12 18/16

24/12 20Ø24/12 20Ø

M M

BB

36/18

/1

Ø

12Ø

24Ø

Ø 12Ø

MAX

3'-0".

MAX

3'-0".

SUPPLY AIR

FLOW

36/18

/1

Ø

12Ø

24Ø

Ø

12Ø

DIFFUSER TAG GRILLE & REGISTER TAG

LINEAR DIFFUSER TAG

CONTROL TAG

T

S

CO

CO

EQUIPMENT TAG

WALL MOUNTED THERMOSTAT

/TEMPERATURE SENSOR

WALL MOUNTED SWITCH

WALL MOUNTED CARBON MONOXIDE SENSOR

WALL MOUNTED CARBON

DIOXIDE SENSOR2

AF

UNIT NUMBER

EQUIPMENT TYPE

AHU-1

UNIT NUMBER

EQUIPMENT TYPE

X-XX-X

X

X-XX

X

(TYP OF X)

CFM

PLENUM INLET SIZE

LENGTH

TYPE (SEE SCHEDULE)

TYPICAL OF X

AIR FLOW RATE

NECK SIZE

TYPE (SEE SCHEDULE)

AIR VENT MANUAL

PIPE ANCHOR

4" AD-1

AREA DRAIN (4" CONN.)

TYPE (SEE SPEC.)

CLEAN OUT

CLEAN OUT (FLOOR)

CLEAN OUT (WALL)

DOWN SPOUT NOZZLE

EXPANSION JOINT

FLEXIBLE CONNECTION

FLOOR DRAIN (2" CONN.)

FLOOR SINK (2" CONN.)

FLOW DIRECTION

FLOW SWITCH/SENSOR

HOSE BIB OR DRAIN VALVE

ORIFICE

PRESSURE GAUGE W/COCK

CONT. PIPE NOT SHOWN

PIPE CAP

PIPE DOWN

PIPE GUIDE

PIPE TEE

PIPE TEE DOWN

PIPE TEE UP

PIPE UP

PITCH (DOWN IN THE

DIRECTION OF ARROW)

PRESSURE SWITCH/SENSOR

PRESSURE/TEMP. PORT

REDUCER (CONCENTRIC)

REDUCER (ECCENTRIC)

ROOF DRAIN (4" CONN.)

OVERFLOW ROOF DRAIN (4" CONN.)

VENT THRU ROOF (4" CONN.)

STRAINER

STEAM TRAP

THERMOMETER

UNION

WALL HYDRANT

2" FD-1

TYPE (SEE SPEC.)

2" FS-1

TYPE (SEE SPEC.)

4" RD-1

TYPE (SEE SPEC.)

4" ORD-1

TYPE (SEE SPEC.)

4" VTR-1

TYPE (SEE SPEC.)

WH

PT

PS

1/8"

HB

FS

DS

WCO

FCO

CO

DESCRIPTIONSYMBOL DESCRIPTIONSYMBOLDESCRIPTIONSYMBOL

INDIRECT DRAIN (INSIDE DIAMETER)

INSULATION

INTERNAL

INVERT ELEVATION

IRON PIPE SIZE

ISOLATOR/ISOLATION

INTERNAL STATIC PRESSURE

INFRARED HEATER

LEAVING AIR TEMPERATURE

LAVATORY

LOCAL CONTROL PANEL

LINEAR FEET

LIQUID

LAUNDRY TUB

LEAVING

LOUVER

LEAVING WATER TEMPERATURE

MIXED AIR

MIXED AIR TEMPERATURE

MAKE UP AIR UNIT

MOP BASIN

MANUFACTURER

MANHOLE

MOTORIZED

THERMOSTATIC MIXING VALVE

NORMALLY CLOSED (NOISE CRIT.)

NEGATIVE

NORMALLY OPEN

NOT TO SCALE

OUTSIDE AIR

OPPOSED BLADE DAMPER

ON CENTER

OUTSIDE DIAMETER

OPEN END DUCT

OVERFLOW ROOF DRAIN

OUTSIDE STEM AND YOKE

PUMP

PUMPED CONDENSATE RETURN

PRESSURE DROP

PLUMBING

PANEL

PRESSURE REDUCING VALVE

RETURN AIR

REHEAT COIL

ROOF DRAIN

REFRIGERANT/REFRIGERATE

REGISTER

REQUIRED

RELIEF FAN

RELATIVE HUMID. (ROOF HYDRANT)

RECIRCULATING HOT WATER

REDUCED PRESSURE ZONE

RETURN

ROOF TOP UNIT

RAIN WATER LEADER

SOUND ATTEN. (SUPPLY AIR)

SANITARY

SUPPLY AIR TEMPERATURE

SUPPLY FAN

STATIC PRESSURE (SUMP PUMP)

SPRINKLER

STAINLESS STEEL

SUPERVISORY SWITCH

STORAGE TANK

STEAM

SUCTION

SINK

SHOWER DRAIN (STORM DRAIN)

SHOWER

SERVICE SINK

TEMPERATURE CONTROL CONTR.

TEMP. DIFF. (TRENCH DRAIN)

TEMPERATURE - DRY BULB

TEMPERATURE - DEW POINT

THERMOSTATIC MIXING VALVE

TOTAL STATIC PRESSURE

TEMPERATURE - WET BULB

THERMOSTATIC EXPANSION VALVE

TYPICAL

URINAL

UNDERGROUND

UNIT HEATER

VALVE

VARIABLE AIR VOLUME (TERM. UNIT)

VACUUM BREAKER

VOLUME DAMPER

VARIABLE FREQUENCY DRIVE

VERIFY IN FIELD

VACUUM PUMP

VACUUM RETURN

VENT THROUGH ROOF

WITH

WITHOUT

WATER COLUMN (WATER CLOSET)

WALL HYDRANT

WALL POST INDICTOR VALVE

WATER GAUGE

WATER TO WATER HEAT EXCH.

WATER SOFTENER

WATER SOURCE HEAT PUMP

WET STANDPIPE

ID

INSUL

INT

I.E.

IPS

ISO

ISP

IR

LAT

LAV

LCP

LF

LIQ

LT

LV

LVR

LWT

MA

MAT

MAU

MB

MFR

MH

MOT

MV

NC

NEG

NO

NTS

OA

OBD

OC

OD

OED

ORD

OS&Y

P

PCR

PD

PLBG

PNL

PRV

RA

RC

RD

REFR

REG

REQ

RF

RH

RHW

RPZ

RTN

RTU

RWL

SA

SAN

SAT

SF

SP

SPKLR

S/S

SSW

ST

STM

SUCT

S

SD

SH

SS

TCC

TD

TDB

TDP

TMV

TSP

TWB

TXV

TYP

U

UG

UH

V

VAV

VB

VD

VFD

VIF

VP

VR

VTR

W/ W/O

WC

WH

WPIV

WG

WHX

WS

WSHP

WSP

ABBREVIATIONS

DESCRIPTIONSYMBOL

GLYCOL WATER SUPPLY

GLYCOL WATER RETURN

GWS

GWR

CHILLED WATER SUPPLY

CHILLED WATER RETURN

CHWS

CHWR

REFRIGERANT LIQUID

REFRIGERANT SUCTION/GAS

RL

RS

AIR SEPARATOR

LOW PRESSURE STEAM

LOW PRESSURE RETURN

LPS

LPR

H WALL MOUNTED HUMIDIFIER

DESCRIPTIONSYMBOL

DEMOLITION SYMBOLS

PIPE TO BE REMOVED

DUCT TO BE REMOVED

EQUIPMENT TO BE REMOVED

CONNECT TO EXISTING PIPE OR DUCT

FD SD

FSD

3-WAY VALVE

ANGLE VALVE

BALANCING VALVE

GATE VALVE

BALL VALVE

BUTTERFLY VALVE

CHECK VALVE

SHUTOFF VALVE (ALL TYPES)

PRESSURE REDUCING VALVE

PRESSURE RELIEF VALVE

MOTORIZED VALVE

FLOW VENTURI

BACKFLOW PREVENTER

DESCRIPTIONSYMBOL

AUTOMATIC AIR VENTAV

M

CALIBRATED BALANCE VALVE

VALVE SYMBOLS

EXHAUST ROUND

XX-X

XX

(TYP OF X)TYPICAL OF X

AIR FLOW RATE

GRILLE/REGISTER SIZE

TYPE (SEE SCHEDULE)

DUCT SYMBOLS

DESCRIPTIONSYMBOL

NTRUE

NORTH

ACTUAL SQ. FT.

PROGRAMMED SQ. FT.

ROOM NUMBER

DOOR NUMBER

KEYNOTE

REVISION NUMBER

ELEVATION INDICATION

COLUMN GRID

IDENTIFICATION

NORTH ARROW

BUILDING SECTION

WALL SECTION

EXTERIOR/INTERIOR

ELEVATION

ELEVATION NUMBER

SHEET ON WHICH

ELEVATION IS DRAWN

DETAIL SECTION

REFERENCE

DESCRIPTIONSYMBOL DESCRIPTIONSYMBOL

LEO A DALY Company 2014

A

B

C

D

A

B

C

D

2 3 4 5

P L

A N

N I N

G A

R C

H I T

E C

T U

R E

E N

G I N

E E

R I N

G I N

T E

R I O

R S

ES

T

S ec o n d A ve n u e

So u th

Su it e

M in n ea p o li s, -2

U

SA

T el

-3

-8

F ax

-3

-4

G R

A N

D F

O R

K S

A F

B , N

D C

O N

T R

A C

T S

E

LE

M E

N T

C

IV

IL

E

N G

IN

E

E R

S Q

U A

D R

O N

A

IR

M O

B

IL

IT

Y

C O

M M

A N

D

D E

P A

R T

M E

N T

O F

T H

E A

IR

F

O R

C E

P R

O

JE

C T

N U

M B

E R

: G F

A F

B J

F S

D

P

LO

T S

C A

LE

P

LO

T D

A T

E

C H

K B

Y

D W

N B

Y

D E

S

IG

N E

D B

Y

F

IL

E N

A M

E

D A

T E

1 2 3 4 5

Sheet of 25

A S

IN

D

IC

A

T E

D

/1

/2

:1

:2

P

M

S Y

M B

O L S

A N

D A

B B

R

IV

A T

IO

N

S

JF

S

D

R ep ai r H

V A

C C on tro ls /E qu ip m en t -

R

G

A B

W B ui ld in g

1-

5-

3-

-2

B

LB

N R

W

N

JB

100% SUBMITTAL

G-002

3-

-2

JF

S

D _G

-0

N O

D

ES

C

R

IP

T

IO

N D

A

U.S. 2

C O

U N

T Y

R O

A D

B

U.S. 2

PERIMETER SECURITY ROAD

ALERT AVE

E

IE

L S

O N

S T

E

IE

L S

O N

S T

B S

T R

E E

T

7TH AVE

TUSKEGEE AIRMEN BLVD

STEEN BLVD

1ST AVE

G S

T R

E E

T

R O

A D

TAXIWAY D

T A

X

IW

A Y

A

R U

N W

A Y

EIELSON

ELEMENTARY

SCHOOL

100101

100100

145 6245

602600

846847

999999

748749750 747

107433

20192017

TWINING SCHOOL

EIELSON

ELEMENTARY

SCHOOL

2016 2018 2020 2022

2024 2026

15691567 15651563

1572 1574 1576 1578

15791577 15751573

1593 1591

1104 1110

1115 1117

1592 1590 1588 1586

2070 2068 2066

1134 1136 1138 1140

1139 1141

1371 2

1452 1454

1449 1451 1453

10681066

10601058

10691067

22692273

10211025

10611059

1046 1048 1050 1052 1054 1056

16221624162616281630

162116231625162716291631

1605160316011597

1596 1598 1600 1602 1604

10281030

13401338

81519

1075 1073

1343 1347

1370 1374

13351331

1406 1408

4 1187

1 2

1118 1120 1122

13231315

1121 1123

1114 1116

14821124

1480 1478 1486 1474

1496 1498

1477 1475

10991095

1126 1128 1130 1132

1133113111291127

C O

U N

T Y

R O

A D

B

E

IE

L S

O N

S T

L O

U

IS

IA

N

A S

T

STEEN BLVD.

D A

K O

T A

D R

7TH AVE

H S

T

G S

T

ALERT AVE

H S

T

R O

A D

R O

A D

R O

A D

REDWOOD DR

HEMLOCK RD

CEDAR AVE

MARCH DR

SYCAMORE DR

SPRUCE DR

BEECH DR

DOGWOOD DR

E

IE

L S

O N

S T

J S

T

I S

T

10TH AVE

ASPEN AVE

LILAC COURT

SPRUCE DR

K E

N T

U C

K Y

S T

WILLOW AVE

SUNFLAKE CIR

1ST AVE

F S

T

E

IE

L S

O N

S T

BEECH DR

NEVADA DR

REDWOOD DR

SUNFLAKE C

IR

3RD AVE

HICKAM DR.

TUSKEGEE AIRMEN BLVD

IO

W

A S

T

DOGWOOD DR

REDWOOD DR

H A

W A

II

S

T

MARCH DR

WARRIOR DR

POPLAR AVE

KORINA AVE.

ALERT AVE.

IN

D

IA

N

A S

T

H O

L Z

A P

P L E

S T

MALMSTROM AVE

H O

L Z

A P

P L E

S T

ASH AVE

2ND AVE

PENN AVE

HEMLOCK RD

TEAK AVE TEAK AVE

HOLLY DR

SYCAMORE DR

MAXWELL AVE

BEECH DR

RED OAK AVE

M E

A D

O W

L A

R K

L N

W H

IT

E

M A

N S

T

V A

N D

E N

B U

R G

S T

J

ST

U.S. 2

CYPRESS DR.

CYPRESS DR.

W A

R R

E N

S T

J S

T

STEEN BLVD

L O

U

IS

I A N

A S

T

SPRUCE DR

SPRUCE DR

JUNIPER AVE

GUMWOOD AVE

O R

E G

O N

S T

MARCH DR

RANDOLPH AVE

FIR AVE

LANGLEY AVE

HICKAM DR.

A S

T

BIRCH AVE

J S

T

M

IS

S O

U R

I S

T

N E

W J

E R

S E

Y S

T

FREEDOM DR

ELLSWORTH AVE

M O

N T

A N

A S

T

CEDAR AVE

H

IC

K A

M C

IR

LOX AVE.

N O

R T

O N

S T

STEEN BLVD.

E

IE

L S

O N

S T

E

IE

L S

O N

S T

E

IE

L S

O N

S T

ROAD 16

REDWOOD DR

ASPEN AVE

MSA SECURITY ROAD

C O

N T

R A

C T

O R

'S R

O W

P E

R

IM

E T

E R

S E

C U

R I T

Y R

O A

D

U.S. 2

R O

A D

P E

R I M

E T

E R

S E

C U

R

IT

Y R

O A

D

R O

A D

ROAD 25

PERIMETER SECURITY ROAD

R O

A D

P E

R

IM

E T

E R

S E

C U

R I T

Y R

O A

D

R O

A D

ROAD 3

P E

R

IM

E T

E R

S E

C U

R I T

Y R

O A

D

U.S. 2

R O

A D

R O

A D

R O

A D

R O

A D

ALERT AVE

NEVADA DR

J S

T J S

T J S

T

J S

T J S

T J S

T J S

T

STEEN BLVD.STEEN BLVD.

B S

T

R O

A D

ROAD 11

TAXIWAY

TRANSIENT

AIRCRAFT

PARKING

BRAVO

RAMP

T A

X

IW

A Y

A

R U

N W

A Y

DELTA

607-M-101

A1

HWY 2

I-94 I-94

HWY 2

HWY 2

H W

Y

H W

Y

H W

Y

H W

Y

H W

Y

I-94

I-

I-

GRAND FORKS AFB

MINOT

BEULAH

JAMESTOWN

BISMARCK FARGO

DEVIL'S LAKE

CANADA

NORTH DAKOTA

M O

N T

A N

A

N O

R T

H D

A K

O T

A

N O

R T

H D

A K

O T

A

M

IN

N E

S O

T A

NORTH DAKOTA

SOUTH DAKOTA

NTRUE

NORTH

LEO A DALY Company 2014

A

B

C

D

A

B

C

D

2 3 4 5

P L

A N

N I N

G A

R C

H I T

E C

T U

R E

E N

G I N

E E

R I N

G I N

T E

R I O

R S

ES

T

S ec o n d A ve n u e

So u th

Su it e

M in n ea p o li s, -2

U

SA

T el

-3

-8

F ax

-3

-4

G R

A N

D F

O R

K S

A F

B , N

D

C O

N T

R A

C T

S E

LE

M

E N

T

C

IV

IL

E

N G

IN

E

E R

S Q

U A

D R

O N

A

IR

M O

B

IL

IT

Y

C O

M M

A N

D

D E

P A

R T

M E

N T

O F

T H

E A

IR

F

O R

C E

P R

O

JE

C T

N U

M B

E R

: G F

A F

B J

F S

D

P

LO

T S

C A

LE

P

LO

T D

A T

E

C H

K B

Y

D W

N B

Y

D E

S

IG

N E

D B

Y

F

IL

E N

A M

E

D A

T E

1 2 3 4 5

Sheet of 25

A S

IN

D

IC

A

T E

D

/1

/2

:1

:2

P

M

V

IC

IN

IT

Y M

A P

JF

S

D

R ep ai r

H V

A C

C on tr ol s/ E qu ip m en t -

R

G

A B

W B ui ld in g

1-

5-

3-

-2

B

LB

N R

W

N

JB

100% SUBMITTAL

G-101

3-

-2

JF

S

D _G

-1

SCALE: 1 : 9600G-101

A1 VICINITY MAP

SCALE: NTSG-101

D5 NORTH DAKOTA MAP

N O

D

ES

C

R

IP

T

IO

N D

A

DOUBLE WALL INSULATED

CASING

FILTER MIXING BOX WITH

2" MERV 8 PLEATED FILTERS

CHILLED WATER

COOLING COIL

UPFLOW BELT DRIVEN

SUPPLY FAN.

FLEXIBLE CONNECTOR

(TYPICAL)

OUTSIDE AIR

RETURN AIR

SUPPLY AIR

SECTION VIEW PLAN VIEW

RETURN AIR

ACCESS DOOR

(TYPICAL)

VARIABLE FREQUENCY DRIVEROUTE CONDENSATE

FULL SIZE TO NEAREST

FLOOR DRAIN

DOUBLE WALL INSULATED

CASING

FILTER MIXING BOX WITH

2" MERV 8 PLEATED FILTERS

DUAL CIRCUIT DX

COOLING COIL

UPFLOW BELT DRIVEN

SUPPLY FAN.

FLEXIBLE CONNECTOR

(TYPICAL)

OUTSIDE AIR

RETURN AIR

SUPPLY AIR

FLOOR

SECTION VIEW

PLAN VIEW

ACCESS DOOR

(TYPICAL)

VARIABLE

FREQUENCY

DRIVE

RETURN AIR

ROUTE CONDENSATE

FULL SIZE TO NEAREST

FLOOR DRAIN

HEATING WATER COIL

STANDARD CLEVIS PIPE HANGER

INSULATION PROTECTION SHIELD.

ROD, STEEL, GALVANIZED OR

ELECTRO-PLATED

HEX. NUTS WITH FLAT WASHERS,

GALVANIZED OR ELECTRO-PLATED

CONCRETE

EXPANSION

BOLT CASING

INSULATION WITH HIGH DENSITY

INSERT AT SUPPORTNOTE:

AHU COILS: AIR VENTS AT SUPPLY & RETURN HIGH POINTS AND HEADERS AS SHOWN. VAV & REHEAT

COILS: AIR VENTS (KEY OPERATED) ON RETURN ONLY. OMIT THERMOMETERS AND GAUGES.

UNION (TYP)

AHU COILS: MANUAL AIR

VENT AT EACH HEADER

COIL

VAV & REHEAT COILS: MANUAL AIR VENT

W/KEY OPERATED VALVE AT CEILING

FLOW

AIR

BALANCE PLUG

VALVE (TYP)

THERMOMETER (TYP)

DRAIN VALVE WITH HOSE

CONNECTION (TYP)

PETCOCK AND

PRESSURE GAUGE (TYP)

STRAINER

SHUT OFF VALVE (TYP)

MANUAL VENT (TYP)

3-WAY VALVE

BALANCING VALVE

2 PIPE DIA.

5 PIPE DIA.

RETURN

SUPPLY

GALVANIZED BOLT PER

MANUFACTURERS

INSTALLATION

RECOMMENDATIONS

ROOF STRUCTURE

REFRIGERANT

PIPING

ROOF SUPPORT RAIL

ROOF CURB MUST BE

DESIGNED FOR WIND

RESTRAINT

RUBBER GROMMET

AIR COOLED CONDENSING UNIT

2" WIDE STAINLESS

STEEL STRAPS OVER

UNIT, SECURED TO ROOF

RAIL AS INDICATED

ROOF MEMBRANE

FLASHING SET IN

BONDING ADHESIVE

HEAT WELD EDGE

SEALANT AS

REQUIRED

24 GAUGE PREFINISHED

METAL COUNTER

FLASHING WITH HIGH-

DOMED CAPPED NO. 10 x

1-1/2" GALVANIZED SCREW

AND NEOPRENE WASHER

PIPE CLAMP W/ VIBRA STRIP PIPE CUSHION

ADDITIONAL

MEMBRANE PAD SET IN

BONDING ADHESIVE

ROOF

PIPE PIER PIPE BLOCK

PIPE

DOUBLE WALL INSULATED

CASING

FILTER SECTION WITH

2" MERV 8 PLEATED FILTERS

DUAL CIRCUIT DX

COOLING COIL

UPFLOW BELT DRIVEN

SUPPLY FAN.

PUMPED CONDENSATE

RETURN AIR

SUPPLY AIR

FLOOR

SECTION VIEW

RELOCATE EXISTING CONDENSATE PUMP TO

ACCOMMODATE NEW AIR HANDLING UNIT -- ROUTE

CONDENSATE FULL SIZE TO NEW CONDENSATE PUMP

LOCATION -- REROUTE PUMPED CONDENSATE AS REQUIRED

HEATING WATER COIL

PLAN VIEW

RETURN AIR

ACCESS DOOR

(TYPICAL)

VARIABLE

FREQUENCY

DRIVE

12"

LEO A DALY Company 2014

A

B

C

D

A

B

C

D

2 3 4 5

P L

A N

N I N

G A

R C

H I T

E C

T U

R E

E N

G I N

E E

R I N

G I N

T E

R I O

R S

ES

T

S ec o n d A ve n u e

So u th

Su it e

M in n ea p o li s, -2

U

SA

T el

-3

-8

F ax

-3

-4

G R

A N

D F

O R

K S

A F

B , N

D

C O

N T

R A

C T

S E

LE

M

E N

T

C

IV

IL

E

N G

IN

E

E R

S Q

U A

D R

O N

A

IR

M O

B

IL

IT

Y

C O

M M

A N

D

D E

P A

R T

M E

N T

O F

T H

E A

IR

F

O R

C E

P R

O

JE

C T

N U

M B

E R

: G F

A F

B J

F S

D

P

LO

T S

C A

LE

P

LO

T D

A T

E

C H

K B

Y

D W

N B

Y

D E

S

IG

N E

D B

Y

F

IL

E N

A M

E

D A

T E

1 2 3 4 5

Sheet of 25

A S

IN

D

IC

A

T E

D

/1

/2

:1

:2

P

M

G E

N E

R A

L D

E T

A

IL

S

JF

S

D

R ep ai r

H V

A C

C on tr ol s/ E qu ip m en t -

R

G

A B

W B ui ld in g

1-

5-

3-

-2

B

LB

N R

W

N

JB

100% SUBMITTAL

G-501

3-

-2

JF

S

D _G

-5

SCALE: NTSG-501

D1 B607 AHU-16

SCALE: NTSG-501

D3 B607 AHU-20

SCALE: NTSG-501

B2 CEILING HUNG PIPE SUPPORT FOR INSUL. PIPE DETAIL

SCALE: NTSG-501

B1 WATER COIL PIPING DETAIL (3-WAY VALVE)

SCALE: NTSG-501

B3 ROOF MOUNTED CONDENSING UNIT DETAIL

SCALE: NTSG-501

A1 ROOF PIPING SUPPORT DETAIL

SCALE: NTSG-501

A2 B607 AHU-19

N O

D

ES

C

R

IP

T

IO

N D

A

AHU-20

15/56

28/48

30/36

EXISTING

SUPPLY

EXISTING

OUTSIDE AIR

AHU-19

26/12

12/26

EXISTING

RETURN

12/26

AHU-16

17/80

EXISTING

SUPPLY

18/28

EXISTING

OUTSIDE AIR

LEO A DALY Company 2014

A

B

C

D

A

B

C

D

2 3 4 5

P L

A N

N I N

G A

R C

H I T

E C

T U

R E

E N

G I N

E E

R I N

G I N

T E

R I O

R S

ES

T

S ec o n d A ve n u e

So u th

Su it e

M in n ea p o li s, -2

U

SA

T el

-3

-8

F ax

-3

-4

G R

A N

D F

O R

K S

A F

B , N

D

C O

N T

R A

C T

S E

LE

M

E N

T

C

IV

IL

E

N G

IN

E

E R

S Q

U A

D R

O N

A

IR

M O

B

IL

IT

Y

C O

M M

A N

D

D E

P A

R T

M E

N T

O F

T H

E A

IR

F

O R

C E

P R

O

JE

C T

N U

M B

E R

: G F

A F

B J

F S

D

P

LO

T S

C A

LE

P

LO

T D

A T

E

C H

K B

Y

D W

N B

Y

D E

S

IG

N E

D B

Y

F

IL

E N

A M

E

D A

T E

1 2 3 4 5

Sheet of 25

A S

IN

D

IC

A

T E

D

/1

/2

:1

:2

P

M

G E

N E

R A

L S

C H

E D

U

LE

S A

N D

S E

C T

IO

N

S

JF

S

D

R ep ai r

H V

A C

C on tr ol s/ E qu ip m en t -

R

G

A B

W B ui ld in g

1-

5-

3-

-2

B

LB

B C

P

N

JB

100% SUBMITTAL

G-601

3-

-2

JF

S

D _G

-6

AIR COOLED CONDENSER SCHEDULE

MARK LOCATION SERVES

NET COOL CAP

TONS

COMPRESSOR DATA CONDENSER DATA ELECTRICAL DATA

MANUFACTURER MODEL NOTESNO. REFR. TYPES NO. STEPS

CONDENSER FAN NO. REF.

CIRCUITS VOLTAGE PHASE HZNO. HP EA

CU-19 ROOF AHU-19 5 1 R-410A 1 1 0.20 1 208 1 60 TRANE 4TTA3060D4000 1, 2, 3, 4, 8

CU-20 ROOF AHU-20 20 2 R-410A 2 2 1.00 2 460 3 60 TRANE TTA240E4HRA 5, 6, 7, 8

CU-INTEL HVAC ROOF AHU-INTEL HVAC 4 1 R-410A 1 1 0.20 1 208 1 60 TRANE 4TTA3048D4000 1, 2, 3, 4, 8

AIR HANDLING UNIT SCHEDULE

MARK LOCATION

SUPPLY FAN HEATING COIL COOLING COIL ELECTRICAL

MANUFACTURER MODEL NOTES

SUPPLY AIR

(CFM) ESP HP TYPE

CAPACITY

(MBH) GPM

FLUID PD

(FT H2O)

FACE VELOCITY

(FPM) KW TYPE

TOTAL

CAPACITY

(MBH)

SENSIBLE

CAPACITY

(MBH) GPM

FACE

VELOCITY

(FPM) VOLTAGE PHASE HZ

AHU-16 ROOM 206 6400 1.50 in-wg 7.5 NONE 0.0 0.00 0 0 0 CHILLED WATER 154.08 138.77 30.71 521 208 3 60 TRANE PERFORMANCE CLIMATE CHANGER UNIT SIZE 21 1, 2, 3, 4, 5

AHU-19 ROOM 103C 2000 1.00 in-wg 1 30% GLYCOL 58.6 4.19 0.28 514 0 DX 50.66 50.66 0 500 208 3 60 TRANE BCVD054G2 2, 3, 4, 5

AHU-20 ROOM 246 9100 1.50 in-wg 10 30% GLYCOL 355.3 24.95 1.68 447 0 DX 250.73 250.71 0 447 460 3 60 TRANE PERFORMANCE CLIMATE CHANGER UNIT SIZE 21 1, 2, 3, 4, 5

AHU-INTEL HVAC ROOM 119 900 0.50 in-wg 1 ELECTRIC 27.3 0.00 0 0 8 DX 43.19 28.24 0 338 208 3 60 TRANE BCHD036G2 3, 4

NOTES;

1. PROVIDE VIBRATION ISOLATORS.

2. PROVIDE EVAPORATOR DEFROST CONTROL.

3. PROVIDE HEAD PRESSURE CONTROL.

4. PROVIDE CRANKCASE HEATER.

5. PROVIDE HAILGUARD.

6. PROVIDE RELIATEL MICROPROCESOR CONTROLS

7. PROVIDE RUBBER-IN-SHEAR ISOLATORS.

8. FACTORY MOUNTED AND WIRED DISCONNECT.

SCALE: 1/4" = 1'-0"G-601

A4 SECTION THRU BLDG 607 AHU-20

SCALE: 1/4" = 1'-0"G-601

A3 SECTION THRU BLDG 607 AHU-19

SCALE: 1/4" = 1'-0"G-601

A2 SECTION THRU BLDG 607 AHU-16

NOTES;

1. REFER TO DETAIL FOR UNIT CONFIGURATION.

2. SINGLE POINT POWER CONNECTION.

3. BACKWORD INCLINED BELT DRIVEN SUPPLY FAN.

4. FACTORY MOUNTED AND WIRED DISCONNECT.

5. VARIABLE FREQUENCY DRIVE.

N O

D

ES

C

R

IP

T

IO

N D

A

R

E A

S E

R V

E D

B Y

A H

U -2

A R

E A

S E

R V

E D

B Y

A H

U -1

(R O

O F

A R

E A

S E

R V

E D

B Y

A H

U -13

A R

E A

S E

R V

E D

B Y

A H

U -16

A R

E A

S E

R V

E D

B Y

A H

U -20

A R

E A

S E

R V

E D

B Y

A H

U -6

A R

E A

S E

R V

E D

B Y

H V

U -5 A

R E

A S

E R

V E

D B

Y A

H U

-1 (S

O U

T H

A R

E A

S E

R V

E D

B Y

IN

T

E L

H V

A C

A R

E A

S E

R V

E D

B Y

A H

U -19

A R

E A

S E

R V

E D

B Y

A H

U -2

A R

E A

S E

R V

E D

B Y

A H

U -8

A R

E A

S E

R V

E D

B Y

A H

U -15

A R

E A

S E

R V

E D

B Y

H V

U -2

M

A H

U -1

(R O

O F

)A H

U -2

R O

O F

M

M

M

M

M

A H

U -1

(S O

U T

H

M

M

M

M

M

M

M

M

M

A H

U -2

(F

LO

O R

M

M

M

A R

E A

S E

R V

E D

B Y

A H

U -15

A H

U -6

M

M

M

A H

U -8

(N O

R T

H

M

M

M

A H

U -8

M

M

A H

U -15

A H

U

IN

T E

L H

V A

C

A H

U -15

(W E

S T

M

M

M

M

M

A H

U -16

M

A H

U -13

M

M

M

M

M

M

M

A H

U -19

M

A H

U -20

M

H V

U -2

M

M

M

M

M

H V

U -5

M

M

M

607-M -610

C

607-M -612

C

607-M -613

C

607-M -624

C

607-M -620

C

607-M -615

C

607-M -622

C

607-M -616

C

607-M -619

C

607-M -617

C

607-M -618

C

607-M -621

C

607-M -611

C

607-M -618

C

607-M -614

C 1607-M

-623

C

M

N T

R U

E N

O R

T H

LEO

A

D A

LY

C o m p an y 2

A B C D

A B C D

P L A N N I N G A R C H I T E C T U R E E N G I N E E R I N G I N T E R I O R S

EST. 1915

730 Second Avenue South, Suite 1100 Minneapolis, MN 55402-2455 USA Tel 612-338-8741 Fax 612-338-4840 GRAND FORKS AFB, ND

CONTRACTS ELEMENT

319 CIVIL ENGINEER SQUADRON

AIR MOBILITY COMMAND

DEPARTMENT OF THE AIR FORCE

PROJECT NUMBER: GFAFB JFSD201516 LAD

PLOT SCALE:

PLOT DATE:

CHK BY:DWN BY:

DESIGNED BY:

FILE NAME:

DATE:

S heet of 25

AS INDICATED

4/1/2015 12:16:09 PM

BUILDING 607 - OVERALL PLAN

JFSD201516 Repair HVAC Controls/Equipment - 69 RG & 319 ABW Building 607

021-10085-012

3-20-2015

BLBNJB

NJB100%

S

U B

M

IT

T A

L

607-M -101

3-20-2015

JFSD_607-M-101

S C

A

LE

: 1" = 30'-0" 607-M

-101

A

B U

IL

D

IN

G

- O

V E

R A

L L

K E

Y N

O T

E L

E G

E N

D

M

R E

M O

V E

A L L E

X

IS

T

IN

G P

N E

U M

A T

IC

C

O N

T R

O L S

A N

D R

E P

L A

C E

W

IT

H D

D C

C O

N T

R O

L

S Y

S T

E M

IN

T

E R

F A

C E

D W

IT

H

T H

E C

A M

P U

S E

M C

S . R

E P

R O

G R

A M

A

IR

H A

N D

L E

R

C O

N T

R O

L S

E Q

U E

N C

E S

. R E

F E

R T

O A

IR

H

A N

D L

IN

G U

N

IT

C O

N T

R O

L S

C H

E M

A T

IC

S

F O

R

A D

D

IT

IO

N

A L

IN

F O

R M

A T

IO

N

M

R E

B A

L A

N C

E A

IR

H

A N

D L

IN

G U

N

IT

S U

P P

L Y

, R E

T U

R N

, A N

D O

U T

S

ID

E A

IR

F

L O

W T

O C

F M

IN

D

IC

A

T E

D O

N A

IR

H

A N

D L

IN

G U

N

IT

C O

N T

R O

L S

C H

E M

A T

IC

S

M

A D

JU

S

T A

L L D

A M

P E

R L

IN

K

A G

E S

T O

E N

S U

R E

D A

M P

E R

O P

E R

A T

E S

P R

O P

E R

L Y

T H

R O

U G

H

IT

S F

U L L R

A N

G E

O F

M O

T

IO

N

M

R E

M O

V E

E X

IS

T

IN

G

D R

A

IN

P A

N A

N D

R E

P L A

C E

W

IT

H N

E W

, IN

S

U L A

T E

D , D

O U

B L E

S L O

P E

D S

T A

IN

L E

S S

S T

E E

L D

R A

IN

P

A N

M

R E

P A

IN

T

U N

IT

C

A S

IN

G

W

IT

H W

E A

T H

E R

A N

D U

V R

E S

IS

T

A N

T E

N A

M E

L B

A S

E D

P A

IN

T

R E

F E

R T

O P

A

IN

T S

P E

C

IF

IC

A

T

IO

N F

O R

A D

D

IT

IO

N

A L

IN

F O

R M

A T

IO

N

M

R E

M O

V E

S T

E E

L C

U R

B F

L A

S H

IN

G

A N

D R

E P

L A

C E

W

IT

H C

O A

T E

D A

L U

M

IN

U M

F L A

S H

IN

G

M

R E

P R

O G

R A

M A

IR

H

A N

D L E

R C

O N

T R

O L S

E Q

U E

N C

E S

. R E

F E

R T

O A

IR

H

A N

D L

IN

G U

N

IT

C O

N T

R O

L S

C H

E M

A T

IC

S

F O

R A

D D

IT

IO

N A

L

IN

F O

R M

A T

IO

N

M

P R

O V

ID

E

N E

W O

S H

A A

P P

R O

V E

D B

E L T

G U

A R

D

M

R E

M O

V E

A N

D R

E P

L A

C E

A

IR

H A

N D

L

IN

G U

N

IT

. R E

F E

R T

O E

N L A

R G

E D

P L A

N S

F O

R

A D

D

IT

IO

N

A L

IN

F O

R M

A T

IO

N

M

R E

P A

IR

A

N D

R E

-S E

A L

IN

T E

R

IO

R A

IR

H

A N

D L

IN

G U

N

IT

IN

S

U L A

T

IO

N

M

R E

M O

V E

F A

N

IN

L E

T G

U

ID

E V

A N

E S

B S

H E

E T

IN

D

E X

30% DESIGN SUBMITTAL ISSUED 12-01-2014

60% DESIGN SUBMITTAL ISSUED 01-14-2015

90% DESIGN SUBMITTAL ISSUED 02-23-2015

100% DESIGN SUBMITTAL ISSUED 00-00-0000

S H

E E

T N

O

S H

E E

T N

A M

E

-M

-1

B U

IL

D

IN

G

- O

V E

R A

L L P

L A

N X

X X

X

-M

-4

E N

L A

R G

E D

P L A

N S

B A

H U

-1 A

N D

R O

O M

X X

X X

-M

-4

E N

L A

R G

E D

P L A

N S

B A

H U

-1 A

N D

A H

U -2

X

X X

X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-1 R

O O

F X

X X

X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-1 S

O U

T H

X X

X X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-2 R

O O

F X

X X

X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-2 F

L O

O R

X X

X X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-6 X

X X

X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-8 N

O R

T H

X X

X X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-8 S

O U

T H

X X

X X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-1

X X

X X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-1

X X

X X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-1

X X

X X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-1

X X

X X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B A

H U

-2

X X

X X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B H

V U

-2 X

X X

X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B H

V U

-5 X

X X

X

-M

-6

C O

N T

R O

L S

C H

E M

A T

IC

S

B

IN

T E

L H

V A

C X

X X

X

-E

-4

E L E

C T

R

IC

A L P

L A

N X

X

NO. DESCRIPTION DATE

AHU-16

A2

G-601

80/17

(EXISTING

SUPPLY)

18/28

(EXISTING

OUTSIDE AIR)

M17

AHU-16

(EXISTING)

D04

(EXISTING

SUPPLY)

(EXISTING

OUTSIDE AIR) 80/17

18/28

AHU-INTEL

HVAC

EXISTING

RETURN

EXISTING

SUPPLY

M18

EXISTING CONDENSATE PUMP TO

REMAIN -- REWORK PIPING

CONNECTIONS AS REQUIRED

DX PIPING TO CU-INTEL-HVAC

ON ROOF ABOVE

D05

AHU-INTEL HVAC

(EXISTING)

EXISTING

RETURN

EXISTING

SUPPLY

D02

CU-INTEL HVAC

(EXISTING)

CU-INTEL

HVAC

M16

DX PIPING TO AHU-INTEL-HVAC

BELOW

ROOF PIPE SUPPORTS 4'-0" O.C.

(TYP.) -- REFER TO A1/G-501

NTRUE

NORTH

LEO A DALY Company 2014

A

B

C

D

A

B

C

D

2 3 4 5

P L

A N

N I N

G A

R C

H I T

E C

T U

R E

E N

G I N

E E

R I N

G I N

T E

R I O

R S

ES

T

S ec o n d A ve n u e

So u th

Su it e

M in n ea p o li s, -2

U

SA

T el

-3

-8

F ax

-3

-4

G R

A N

D F

O R

K S

A F

B , N

D

C O

N T

R A

C T

S E

LE

M

E N

T

C

IV

IL

E

N G

IN

E

E R

S Q

U A

D R

O N

A

IR

M O

B

IL

IT

Y

C O

M M

A N

D

D E

P A

R T

M E

N T

O F

T H

E A

IR

F

O R

C E

P R

O

JE

C T

N U

M B

E R

: G F

A F

B J

F S

D

P

LO

T S

C A

LE

P

LO

T D

A T

E

C H

K B

Y

D W

N B

Y

D E

S

IG

N E

D B

Y

F

IL

E N

A M

E

D A

T E

1 2 3 4 5

Sheet of 25

A S

IN

D

IC

A

T E

D

/1

/2

:1

:1

P

M

E N

L A R

G E

D P

LA

N

S B

A H

U -1

A

N D

R O

O M

JF

S

D

R ep ai r

H V

A C

C on tr ol s/ E qu ip m en t -

R

G

A B

W B ui ld in g

1-

5-

3-

-2

B

LB

N

JB

N

JB

100% SUBMITTAL

607-M-401

3-

-2

JF

S

D _6

-M

-4 0 1

SCALE: 1/4" = 1'-0"607-M-401

C3 AHU - 16

SCALE: 1/4" = 1'-0"607-M-401

C1 AHU-16 DEMO

SCALE: 1/4" = 1'-0"607-M-401

B3 B607 - ROOM 119

SCALE: 1/4" = 1'-0"607-M-401

B1 B607 - ROOM 119 DEMO

KEYNOTE LEGEND

D02 REMOVE CONDENSING UNIT AND ASSOCIATED CONTROLS AND REFRIGERANT

PIPING. SEE SPEC FOR REFRIGERANT RECOVERY REQUIREMENTS.

D04 REMOVE AHU, SUPPLY AND OUTSIDE AIR DUCT CONNECTIONS, CHILLED WATER

PIPING CONNECTIONS AND CONTROLS. CAP CHILLED WATER PIPING RUNOUTS FOR

RECONNECTION.

D05 REMOVE AHU, SUPPLY AND RETURN DUCT CONNECTIONS, DX PIPING, CONDENSATE

PIPING CONNECTION AND CONTROLS. CAP CONDENSATE PIPING FOR

RECONNECTION.

M16 INSTALL NEW CONDENSING UNIT ON NEW ROOF CURBS. ROUTE REFRIGERANT

PIPING ON ROOF AND DOWN THRU EXISTING ROOF OPENING.

M17 NEW AHU, ENLARGE EQUIPMENT PAD AS REQUIRED TO ACCOMMODATE UNIT,

RECONNECT SUPPLY AND OUTSIDE AIR DUCTS, RECONNECT CHILLED WATER

PIPING.

M18 NEW AHU HUNG FROM STRUCTURE, RECONNECT SUPPLY AND RETURN DUCTS,

ROUTE DX PIPING FROM UNIT TO CONDENSING UNIT ON ROOF, CONNECT

CONDENSATE PIPE TO EXISTING.

SCALE: 1/4" = 1'-0"607-M-401

A1 B607 - ROOM 119 DEMO ROOF

SCALE: 1/4" = 1'-0"607-M-401

A3 B607 - ROOM 119 ROOF

N O

D

ES

C

R

IP

T

IO

N D

A

AHU-20

A4

G-601

EXISTING

ELECTRICAL

SWITCH

GEAR

EXISTING TELEPHONE

SWITCH EQUIPMENT

SHF-1

(EXISTING

OUTSIDE

AIR)

(EXISTING

SUPPLY)

(EXISTING

RETURN)

36/30

56/15

28/48

30/36

36/30

M20

DX PIPING FROM CU-

20 ABOVE TO AHU-20

REMOVE PORTION OF

EXISTING CMU WALL BELOW

SUPPLY DUCT, AS REQUIRED

TO ALLOW ACCESS TO RM

246 FOR THE REMOVAL AND

REPLACEMENT OF AHU-20.

PROVIDE COMPLETE BUILD-

BACK TO MATCH EXISTING

MATERIALS AND FINISHES.

TOOTH CMU INFILL INTO

ADJACENT WALL.

EXISTING ELECTRICAL

SWITCH GEAR

EXISTING TELEPHONE

SWITCH EQUIPMENT

SHF-1

D07AHU-20

(EXISTING)

28/48

56/15

36/30

(EXISTING

OUTSIDE

AIR)

(EXISTING

SUPPLY)

(EXISTING

RETURN)

REMOVE PORTION OF

EXISTING CMU WALL BELOW

SUPPLY DUCT, AS REQUIRED

TO ALLOW ACCESS TO RM

246 FOR THE REMOVAL AND

REPLACEMENT OF AHU-20.

PROVIDE COMPLETE BUILD-

BACK TO MATCH EXISTING

MATERIALS AND FINISHES.

TOOTH CMU INFILL INTO

ADJACENT WALL.

103C

AHU-19

A3

G-601

(EXISTING

SUPPLY)(EXISTING

RETURN)

26/12 26/12

26/12

26/12

M19

DX PIPING FROM CU-

19 ABOVE TO AHU-19

103C

26/12

26/12 (EXISTING

SUPPLY)(EXISTING

RETURN) AHU-19

(EXISTING)

D06

D02

CU-19

(EXISTING)

CU-19 M16

DX PIPING FROM CU-19

TO AHU-19 BELOW

ROOF PIPE SUPPORTS 4'-0" O.C.

(TYP.) -- REFER TO A1/G-501

D02

CU-20

(EXISTING)

EXISTING

OUTSIDE AIR

CU-20

EXISTING

OUTSIDE AIR

M16

DX PIPING FROM CU-

20 TO AHU-20 BELOW

ROOF PIPE SUPPORTS

4'-0" O.C. (TYP.) --

REFER TO A1/G-501

NTRUE

NORTH

LEO A DALY Company 2014

A

B

C

D

A

B

C

D

2 3 4 5

P L

A N

N I N

G A

R C

H I T

E C

T U

R E

E N

G I N

E E

R I N

G I N

T E

R I O

R S

ES

T

S ec o n d A ve n u e

So u th

Su it e

M in n ea p o li s, -2

U

SA

T el

-3

-8

F ax

-3

-4

G R

A N

D F

O R

K S

A F

B , N

D

C O

N T

R A

C T

S E

LE

M

E N

T

C

IV

IL

E

N G

IN

E

E R

S Q

U A

D R

O N

A

IR

M O

B

IL

IT

Y

C O

M M

A N

D

D E

P A

R T

M E

N T

O F

T H

E A

IR

F

O R

C E

P R

O

JE

C T

N U

M B

E R

: G F

A F

B J

F S

D

P

LO

T S

C A

LE

P

LO

T D

A T

E

C H

K B

Y

D W

N B

Y

D E

S

IG

N E

D B

Y

F

IL

E N

A M

E

D A

T E

1 2 3 4 5

Sheet of 25

A S

IN

D

IC

A

T E

D

/1

/2

:1

:1

P

M

E N

L A R

G E

D P

LA

N

S B

A H

U -1

A

N D

A H

U -2

JF

S

D

R ep ai r

H V

A C

C on tr ol s/ E qu ip m en t -

R

G

A B

W B ui ld in g

1-

5-

3-

-2

B

LB

N

JB

N

JB

100% SUBMITTAL

607-M-402

3-

-2

JF

S

D _6

-M

-4 0 2

SCALE: 1/4" = 1'-0"607-M-402

B3 B607 - AHU-20

SCALE: 1/4" = 1'-0"607-M-402

B1 B607 AHU-20 DEMO

SCALE: 1/4" = 1'-0"607-M-402

D3 B607 - AHU-19

SCALE: 1/4" = 1'-0"607-M-402

D1 B607 - AHU-19 DEMO

KEYNOTE LEGEND

D02 REMOVE CONDENSING UNIT AND ASSOCIATED CONTROLS AND REFRIGERANT

PIPING. SEE SPEC FOR REFRIGERANT RECOVERY REQUIREMENTS.

D06 REMOVE AHU, SUPPLY AND RETURN DUCT CONNECTIONS, DX PIPING, HEATING

WATER PIPING CONNECTIONS AND CONTROLS. CAP HEATING WATER PIPING FOR

RECONNECTION.

D07 REMOVE AHU, SUPPLY, RETURN AND OUTSIDE AIR DUCT CONNECTIONS, DX PIPING,

HEATING WATER PIPING CONNECTIONS AND CONTROLS. CAP HEATING WATER

PIPING FOR RECONNECTION.

M16 INSTALL NEW CONDENSING UNIT ON NEW ROOF CURBS. ROUTE REFRIGERANT

PIPING ON ROOF AND DOWN THRU EXISTING ROOF OPENING.

M19 NEW AHU, ENLARGE EQUIPMENT PAD AS REQUIRED TO ACCOMMODATE UNIT,

RECONNECT SUPPLY AND RETURN DUCTS, ROUTE DX PIPING FROM UNIT TO

CONDENSING UNIT ON ROOF, RECONNECT HEATING WATER PIPING.

M20 NEW AHU, ENLARGE EQUIPMENT PAD AS REQUIRED TO ACCOMMODATE UNIT,

RECONNECT SUPPLY, RETURN AND OUTSIDE AIR DUCTS, ROUTE DX PIPING FROM

UNIT TO CONDENSING UNIT ON ROOF, RECONNECT HEATING WATER PIPING.

SCALE: 1/4" = 1'-0"607-M-402

D2 B607 - AHU-19 DEMO ROOF

SCALE: 1/4" = 1'-0"607-M-402

D4 B607 - AHU-19 ROOF

SCALE: 1/4" = 1'-0"607-M-402

B2 B607 - AHU-20 DEMO ROOF

SCALE: 1/4" = 1'-0"607-M-402

B4 B607 - AHU-20 ROOF

N O

D

ES

C

R

IP

T

IO

N D

A

TS

HW COIL CW COILPRE-FILTER

PD

SUPPLY FAN

M

EXHAUST FANM

PD

SUPPLY AIR

MIN CFM: 3545, MAX CFM: 10743

OUTDOOR AIR

MIN CFM: 60, MAX CFM: 10743

TS-RM

R E

T U

R N

A

IR

M

IN

C F

M M

A X

C F

M

HW-V1 CW-V1

DP-F1

SD-SA

TS-RAT

TS-SAT

SD-RA

TS-OAT

SA-FAN FS

SAF-VFD

TS-MAT

C06

C08

C07

C03

C16 C08

C06

C11

EX-FAN

C08 C12C15

C15

DPR-EA

AHU-1 (ROOF) CONTROL PANEL LOCATED IN ROOM

220A. PROVIDE NEW DDC CONTROLLER IN

EXISTING PANEL FOR CONNECTION TO THE BASE

EMCS. NEW CONTROLLERS SHALL BE COMPATIBLE

WITH HONEYWELL ENTERPRISE BUILDING INTEGRATOR

(EBI) PLATFORM. REFER TO 230993.

DP-ZONE

C13

C19

1. DDC SYSTEM SHALL BE AN EXTENSION OF THE AIR FORCE BASE'S EXISTING HONEYWELL

ENTERPRISE BUILDING INTEGRATOR (EBI) 400.2 ENERGY MANAGEMENT AND CONTROL

SYSTEM (EMCS). ALL CONTROLS AND CONTROL ELEMENTS SHALL BE FULLY

INTEGRAGED INTO THE CAMPUS'S EXISTING NETWORK AND SHALL COMMUNICATE WITH

THE EMCS BACKBONE SOFTWARE VIA C-BUS PROTOCOL.

2. ALL CONTROL POINTS SHALL BE ADJUSTABLE BY THE OWNER THROUGH THE CAMPUS

WIDE EMCS.

3. ALL CONTROL ELEMENTS AND HARDWARE INCLUDING BUT NOT LIMITED TO DAMPER

AND VALVE ACTUATORS, SENSORS, SWITCHES, AND MEASURING DEVICES SHALL BE

COMPATIBLE HONEYWELL COMPONENTS FOR INTEGRATION INTO EXISTING HONEYWELL

EMCS.

4. PROVIDE ALL POINTS LISTED AND INDICATED ON CONTROL SCHEMATIC AS WELL AS ANY

ADDITIONAL HARDWARE AND SOFTWARE POINTS REQUIRED TO ACCOMPLISH THE

SEQUENCE OF OPERATIONS.

GENERAL NOTES

LEO A DALY Company 2014

A

B

C

D

A

B

C

D

2 3 4 5

P L

A N

N I N

G A

R C

H I T

E C

T U

R E

E N

G I N

E E

R I N

G I N

T E

R I O

R S

ES

T

S ec o n d A ve n u e

So u th

Su it e

M in n ea p o li s, -2

U

SA

T el

-3

-8

F ax

-3

-4

G R

A N

D F

O R

K S

A F

B , N

D

C O

N T

R A

C T

S E

LE

M

E N

T

C

IV

IL

E

N G

IN

E

E R

S Q

U A

D R

O N

A

IR

M O

B

IL

IT

Y

C O

M M

A N

D

D E

P A

R T

M E

N T

O F

T H

E A

IR

F

O R

C E

P R

O

JE

C T

N U

M B

E R

: G F

A F

B J

F S

D

P

LO

T S

C A

LE

P

LO

T D

A T

E

C H

K B

Y

D W

N B

Y

D E

S

IG

N E

D B

Y

F

IL

E N

A M

E

D A

T E

1 2 3 4 5

Sheet of 25

A S

IN

D

IC

A

T E

D

/1

/2

:1

:1

P

M

C O

N T

R O

L S

C H

E M

A T

IC

S

B 6 0

A

H U

-1 R

O O

F

JF

S

D

R ep ai r

H V

A C

C on tr ol s/ E qu ip m en t -

R

G

A B

W B ui ld in g

1-

5-

3-

-2

B

LB

N

JB

N

JB

100% SUBMITTAL

607-M-610

3-

-2

JF

S

D _6

-M

-6 1 0

SCALE: NTS607-M-610

C1 CONTROL SCHEMATIC - B607 AHU-1 (ROOF)

MECHANICAL POINT LISTING - B607 AHU-1 ROOF

MARK DESCRIPTION U

N

IT

S

T Y

P E

T R

E N

D

S C

H E

D U

L E

D

A L

A R

M

N O

T E

S

CW-V1 3-WAY VALVE % AO YES - -

DP-ZONE BLDG/SPACE PRESSURE IN. WC AI YES - -

HW-V1 3-WAY VALVE % AO YES - -

FS FREEZE STAT DEG. F AI - - YES

TS-MAT MIXED AIR TEMP. DEG. F AI YES - -

TS-OAT OUTDOOR AIR TEMP. DEG. F AI YES - -

TS-RAT RETURN AIR TEMP. DEG. F AI YES - -

TS-SAT SUPPLY AIR TEMP. DEG. F AI YES YES -

DP-F1 PRE-FILTER DIFF. PRESS. IN. WC AI - - YES

EX-FAN EXHAUST AIR FAN MOTOR (CURRENT SENSOR) ON/OFF BI - - YES

SA-FAN SUPPLY AIR FAN MOTOR (CURRENT SENSOR) ON/OFF BI - - YES

SAF-VFD SUPPLY AIR FAN VFD % BO YES YES -

DPR-EA EXHAUST/RELIEF AIR DAMPER

LDPR-OA LINKED OUTDOOR AIR DAMPER % AO YES - -

SD-RA RETURN AIR SMOKE DETECTOR ALARM BI - - YES

SD-SA SUPPLY AIR SMOKE DETECTOR ALARM BI - - YES

TS-RM SPACE TEMP. DEG. F BI YES YES -

KEYNOTE LEGEND

C03 LINKED ACTUATOR AND DAMPER. PROVIDE NEW DDC ACTUATOR. DAMPER TO

REMAIN.

C06 MOTORIZED 3-WAY VALVE AND ACTUATOR TO REMAIN.

C07 PROVIDE NEW FILTER DIFFERENTIAL PRESSURE SENSOR

C08 PROVIDE NEW DUCT MOUNTED, PROBE TYPE TEMPERATURE SENSOR

C11 PROVIDE NEW UNIT MOUNTED, AVERAGING TYPE CAPILARY TUBE TEMPERATURE

SENSOR

C12 PROVIDE NEW UNIT MOUNTED FREEZE STAT

C13 NEW WALL MOUNTED ROOM TEMPERATURE SENSOR. INCLUDE LCD DISPLAY.

OCCUPANCY OVERRIDE AND SETPOINT ADJUSTMENT

C15 EXISTING DUCT MOUNTED SMOKE DETECTOR TO REMAIN

C16 PROVIDE NEW VARIABLE FREQUENCY DRIVE. REMOVE ANY/ALL INLET VANE

DAMPERS.

C19 PROVIDE NEW ZONE/ZONE PRESSURE DIFFERENTIAL SENSOR

B607 AHU-1 (ROOF) SEQUENCE OF OPERATIONS

GENERAL:

THE SYSTEM CONSISTS OF A ROOF MOUNTED EXHAUST FAN (EF-1A) INTERLOCKED WITH A HORIZONTAL PACKAGED ROOF TOP, DRAW THROUGH AIR HANDLING UNIT (AHU-1) EQUIPPED WITH GLYCOL CHILLED WATER AND HOT WATER COILS, FILTER SECTION, MIXING BOX, AND VARIABLE FREQUENCY DRIVE. VARIABLE FREQUENCY DRIVE IS PROVIDED FOR BALANCING PURPOSES.

OPERATING SCHEDULE

OPERATING HOURS ARE SET THROUGH THE BASE EMCS.

MORNING START-UP SEQUENCE

THE SYSTEM SHALL UTILIZE AN OPTIMIZED MORNING START-UP ROUTINE, INCORPORATING OUTSIDE AIR TEMPERATURE, ZONE TEMPERATURE, AND PAST HISTORY OF BUILDING RESPONSE TO DETERMINE THE OPTIMUM TIME TO INITIATE START UP. UPON INITIATING MORNING START UP, THE ZONE TEMPERATURE SETPOINT SHALL BE RESET TO THE OCCUPIED MODE. AIR HANDLING UNIT OUTDOOR AIR DAMPER AND RELIEF AIR DAMPER SHALL BE FULLY CLOSED. RETURN AIR DAMPER SHALL BE FULLY OPEN. SYSTEM SHALL EXECUTE A MORNING WARM-UP SEQUENCE DURING THE HEATING SEASON AND SHALL EXECUTE A MORNING COOL-DOWN SEQUENCE DURING THE COOLING SEASON.

DURING MORNING WARM UP, CHILLED WATER CONTROL VALVE SHALL BE IN THE FULL BYPASS POSITION. HOT WATER CONTROL VALVE SHALL MODULATE TO THE FULL COIL FLOW POSITION. SUPPLY FAN SHALL MODULATE THROUGH ITS VARIABLE FREQUENCY DRIVE TO FULL FLOW AND THE SYSTEM SHALL DELIVER HEATED AIR TO THE SPACE. MORNING WARM-UP IS TERMINATED WHEN THE SPACE REACHES SETPOINT. UPON TERMINATION OF MORNING WARM-UP, SYSTEM SHALL REVERT TO THE OCCUPIED MODE SEQUENCE.

DURING MORNING COOL DOWN, HOT WATER CONTROL VALVE SHALL BE IN THE FULL BYPASS POSITION. CHILLED WATER CONTROL VALVE SHALL MODULATE FULLY OPEN. SUPPLY FAN SHALL MODULATE TO FULL FLOW AND THE SYSTEM SHALL DELIVER COOL AIR TO THE SPACE.

MORNING COOL DOWN IS TERMINATED WHEN THE SPACES REACHES SETPOINT. UPON TERMINATION OF MORNING COOL DOWN, THE SYSTEM

SHALL REVER TO THE OCCUPIED MODE SEQUENCE.

OCCUPIED MODE HEATING

SUPPLY FAN RUNS CONTINUOUSLY. THE LINKED RETURN AIR AND OUTSIDE AIR DAMPERS SHALL MODULATE TO THE MINIMUM OCCUPPIED OUTDOOR AIR VENTILATION POSITION. SUPPLY AIR FLOW IS ADJUSTED THROUGH THE SUPPLY FAN VARIABLE FREQUENCY DRIVE TO THE MINIMUM SETTING OF 3500 CFM. HOT WATER CONTROL VALVE IS MODULATED FROM FULL BYPASS TO FULL COIL FLOW AS REQUIRED TO MAINTIAN SPACE TEMPERATURE SETTING OF 68 DEG F. IF HEATING VALVE IS FULLY OPEN AND SPACE TEMPERATURE CONTINUES TO DROP, FAN SPEED SHALL BE INCREASED THROUGH THE SUPPLY FAN VARIABLE FREQUENCY DRIVE UNTIL SPACE TEMPERATURE SETPOINT IS ACHIEVED. FAN MODULATION SHALL NOT EXCEED 5% PER MINUTE (ADJUSTABLE). CHILLED WATER CONTROL VALVE SHALL BE IN THE FULL

BYPASS POSITION.

OCCUPIED MODE COOLING

SUPPLY FAN RUNS CONTINUOUSLY. SUPPLY AIR FLOW IS ADJUSTED THROUGH THE SUPPLY FAN VARIABLE FREQUENCY DRIVE TO THE MINIMUM SETTING OF 3500 CFM. WHEN OUTSIDE AIR TEMPERATURE IS GREATER THAN RETURN AIR TEMPERATURE, THE LINKED RETURN AIR AND OUTSIDE AIR DAMPERS SHALL MODULATE TO THE MINIMUM OCCUPIED OUTDOOR AIR VENTILATION POSITION. CHILLED WATER CONTROL VALVE IS MODULATED FROM FULL BYPASS TO FULL COIL FLOW AS REQUIRED TO MAINTAIN SPACE TEMPERATURE OF 74 DEG F. IF CHILLED WATER CONTROL VALVE IS FULLY OPEN AND SPACE TEMPERATURE CONTINUES TO RISE, FAN SPEED SHALL BE INCREASED THROUGH THE SUPPLY FAN VARIABLE FREQUENCY DRIVE UNTIL SPACE TEMPERATURE SETPOINT IS ACHIEVED. FAN MODULATION SHALL NOT EXCEED 5% PER MINUTE (ADJUSTABLE). HOT WATER CONTROL VALVE SHALL BE IN THE FULL BYPASS POSITION WHEN UNIT IS IN COOLING MODE.

WHEN OUTSIDE AIR TEMPERATURE IS LESS THAN RETURN AIR TEMPERATURE AND NO GREATER THAN 70 DEG F. THE UNIT SHALL GO INTO AIR SIDE ECONOMIZER MODE. OUTSIDE AIR DAMPERS SHALL MODULATE OPEN AND RETURN AIR DAMPER AIR DAMPER SHALL CLOSE AND RELIEF FAN EF-1A SHALL BE ENERGIZED AND THE UNIT SHALL PROVIDE 100% OUTSIDE AIR. CHILLED WATER CONTROL VALVE SHALL MODULATE FROM FULL BYPASS TO FULL COIL FLOW AS REQUIRED TO MAINTAIN 74 DEGREE SPACE TEMPERATURE.

UNOCCUPPIED MODE

SUPPLY FAN SHALL CYCLE DURING UN-OCCUPPIED HOURS. OUTSIDE AIR DAMPER IS FULLY CLOSED AND RETURN AIR DAMPER IS FULLY OPEN. SUPPLY FAN SHALL CYCLE ON AND COOLING VALVE SHALL MODULATE TO MAINTAIN SETBACK TEMPERATURE OF 80 DEG. F. DURING COOLING OPERATION. SUPPLY FAN SHALL CYCLE ON AND HEATING VALVE SHALL MODULATE TO MAINTAIN SETBACK TEMPERATURE OF 60

DEG. F. DURING HEATING OPERATION.

SCHEDULE OVERRIDE

WALL MOUNTED NETWORKED DDC TEMPERATURE SENSOR IS INSTALLED ON THE FACE OF THE ASSOCIATED CONTROL PANEL. THE TEMPERATURE SENSOR INCLUDES UNOCCUPPIED/OCCUPPIED OVERIDE AND LCD DISPLAY FOR TEMPERATURE, SETPOINT, AND FAN STATUS. WHEN OVERIDE BUTTON IS PUSHED, THE SYSTEM SHALL BE OVERIDDEN TO THE OCCUPPIED MODE FOR A PERIOD OF 2 HOURS

AFTER WHICH THE SYSTEM WILL RETURN TO THE UNOCCUPPIED MODE.

EXHAUST FAN CONTROL

EXHAUST FAN EF-1A SHALL BE ENERGIZED WHEN ECONOMIZER MODE IS INITIATED. MOTORIZED DAMPER AT EXHAUST FAN EF-1A SHALL MODULATE FROM FULLY CLOSED TO FULLY OPEN AS REQUIRED TO MAINTAIN SPACE PRESSURE OF 0.05" ABOVE REFERENCE.

EMERGENCY SHUT-DOWN

AN EMERGENCY SHUT-DOWN OVERRIDE SHALL BE ACCESSIBLE THROUGH THE OPERATOR WORKSTATION. UPON ACTIVATION OF THE EMERGENCY SHUT-DOWN ROUTINE, THE AIR HANDLING UNIT AND ASSOCIATED FANS SHALL BE DISABLED. OUTSIDE AIR, EXHAUST AIR, AND

RELIEF AIR DAMPERS SHALL CLOSE.

OPERATOR STATION DISPLAY

INDICATE THE FOLLOWING ON THE OPERATOR STATION DISPLAY:

SYSTEM GRAPHIC - AIR HANDLER AND ASSOCIATED RELIEF FAN

SYSTEM OCCUPPIED/UNOCUPPIED MODE

SUPPLY FAN ON/OFF INDICATION

SUPPLY FAN SPEED

SUPPLY AIR TEMPERATURE INDICATION

RETURN AIR TEMPERATURE INDICATION

MIXED AIR TEMPERATURE INDICATION

SPACE TEMPERATURE

SPACE TEMPERATURE SETPOINT

OUTSIDE AIR TEMPERATURE (GLOBAL POINT)

ECONOMIZER MODE INDICATION

RELIEF FAN ON/OFF INDICATION

RELIEF FAN DAMPER POSITION (% OPEN)

RETURN DAMPER POSITION (% OPEN)

OUTSIDE AIR DAMPER POSITION (% OPEN)

SPACE PRESSURE INDICATION

FREEZE STAT INDICATION

SYSTEM SAFETY AND LIMIT CONTROLS

1. EMERGENCY SHUT DOWN SWITCH: ALL AIR HANDLING UNITS, EXHAUST FANS, ETC. SHALL BE SHUT DOWN WHEN THE EMERGENCY SHUT DOWN SWITCH IS ACTIVATED. ALL COMBINATION FIRE/SMOKE DAMPERS, RETURN AIR DAMPERS, EXHAUST AIR DAMPERS, AND OUTSIDE AIR

DAMPERS SHALL CLOSE.

2. DUCT MOUNTED SMOKE DETECTORS: SIGNAL SHALL BE SENT TO THE FIRE ALARM SYSTEM WHEN PRODUCTS OF COMBUSTION ARE DETECTED. ALL AIR HANDLING UNITS, EXHAUST FANS, ETC SHALL BE SHUT DOWN. ALL COMBINATION FIRE/SMOKE DAMPERS, RETURN AIR

DAMPERS, EXHAUST AIR DAMPERS, AND OUTSIDE AIR DAMPERS SHALL CLOSE.

3. FILTER MAINENANCE: THE PRESSURE DIFFERENTIAL SENSOR PD-F1 MOUNTED ACROSS THE FILTER BANK SHALL CONTINUOUSLY MONITOR WHILE THE SUPPLY FAN IS RUNNING. A MAINTENANCE WARNING SHALL BE SENT TO THE BASE EMCS WHEN THE PRESSURE DIFFERENTIAL REACHES 0.75" WC. AN ALARM SHALL BE SENT TO THE BASE EMCS WHEN THE PRESSURE DIFFERENTIAL REACHES 1.0" WC.

4. MIXED AIR TEMPERATURE LOW LIMIT: IF THE MIXED AIR TEMPERATURE FALLS BELOW 35 °F, THE SUPPLY FAN SHALL SHUT DOWN, THE OUTDOOR AIR - RETURN AIR DAMPER SHALL MODULATE TO FULLY CLOSED OUTDOOR AIR DAMPER POSITION AND FULLY OPEN RETURN AIR DAMPER POSITION, AND THE HOT WATER VALVE SHALL OPEN TO 100%.