12-1132B1_18R0014_Attch_4_VAFB_Elec_Mat_Specs.pdf

Vandenberg AFB High Voltage Construction Standard Material

Specifications

The Following pages are of recommended products to be used on Vandenberg AFB as a standard. Suitable substitutes are acceptable if they meet the material in these specifications. Meaning the substitute has the same construction materials i.e. stainless steel, copper, etc. The attached specifications are not recommendations to use a sole source but a construction standard.

FA461018R0014

Attachment 4

Overhead Hardware Specifications

Information compiled by: TSgt Russell Wells

TSgt Rus se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Shackles - Forged and Upset Forged

HEAT TREATED WITH ALLOY PINS

PERMANENTLY MARKED WITH WORKING LOAD LIMITS AND SHACKLE SIZE

ALL SHACKLES ARE STAINLESS STEEL

6:1 SAFETY FACTOR

SCREW PIN ANCHOR

SAFETY PIN ANCHOR

SCREW PIN

SAFETY PIN

STAINLESS STEEL

Federal Specifications RR-C-271 b Type IV Class 6

Federal Specifications RR-C-271 b Type IV Class 1

STAINLESS STEEL

INSIDE LENGTH OUTSIDE INSIDE SAFE WEIGHT

WIDTH CLEAR DIA. Of WIDTH WORKING EA. In

SIZE in PIN DIA. at Pin in Inches EYE at Bow LOAD in Tons Lbs.

Inches in Inches in Inches ANCHOR in Inches in Inches (Heat Treated) ANCHOR

3/16 1/4 3/8 7/8 9/16 19/32 1/3 .05

1/4 5/16 1/2 1-1/8 3/4 3/4 1/2 .10

5/16 3/8 9/16 1-1/4 7/8 1 3/4 .19

3/8 7/16 11/16 1-7/16 1 1-1/8 1 .25

7/16 1/2 3/4 1-11/16 1-1/8 1-1/4 1-1/2 .50

1/2 5/8 13/16 1-7/8 1-3/16 1-5/16 2 .75

5/8 3/4 1-1/16 2-7/16 1-9/16 1-11/16 3-1/4 1.44

3/4 7/8 1-1/4 3 1-7/8 2 4-3/4 2.50

7/8 1 1-7/16 3-5/16 2-1/8 2-1/4 6-1/2 3.50

1 1-1/8 1-11/16 3-3/4 2-3/8 2-5/8 8-1/2 5.25

1-1/8 1-1/4 1-7/8 4-1/4 2-5/8 3 9-1/2 7.25

1-1/4 1-3/8 2 4-1/2 2-15/16 3-3/8 12 9.75

1-3/8 1-1/2 2-1/4 5-1/4 3-5/16 3-5/8 13-1/2 13.25

1-1/2 1-5/8 2-3/8 5-3/4 3-5/8 3-7/8 17 17.70

1-3/4 2 2-7/8 7 4-5/16 5 25 30.38

2 2-1/4 3-1/4 7-3/4 5 5-3/4 35 45.00

2-1/2 2-3/4 4-1/8 10 6 7-1/4 55 85.75

INSIDE LENGTH OUTSIDE SAFE WEIGHT

PIN DIA. WIDTH CLEAR DIA. Of WORKING EACH

SIZE in in at Pin in Inches EYE LOAD in Lbs.

Inches Inches in Inches ANCHOR in Inches in Tons ANCHOR

1/2 5/8 13/16 1-7/8 1-3/16 2 .79

5/8 3/4 1-1/16 2-3/8 1-9/16 3-1/4 1.25

3/4 7/8 1-1/4 2-13/16 1-7/8 4-3/4 2.72

7/8 1 1-7/16 3-5/16 2-1/8 6-1/2 3.95

1 1-1/8 1-11/16 3-3/4 2-3/8 8-1/2 6.12

1-1/8 1-1/4 1-13/16 4-1/4 2-5/8 9-1/2 8.27

1-1/4 1-3/8 2-1/32 4-11/16 3 12 11.71

1-3/8 1-1/2 2-1/4 5-3/16 3-5/16 13-1/2 13.25

1-1/2 1-5/8 2-3/8 5-3/4 3-5/8 17 20.80

1-3/4 2 2-7/8 7 4-1/8 25 33.91

2 2-1/4 3-1/4 7-3/4 5 35 51.75

2-1/2 2-3/4 4-1/8 10-1/2 6 55 98.25

3 3-1/4 5 13 6-1/2 85 153.00

3-1/2 3-3/4 5-1/4 14-5/8 8 120 265.00

4 4-1/4 5-1/2 14-1/2 9 150 338.00

4-1/2 4-3/4 6-3/8 19 15-1/4 200 -

FA461018R0014

se ll W ell s

2-33ADSCO LINE PRODUCTS 03/02 Please call for pricing.

SPECIFICATIONS

MATERIAL: AISI TYPE 316 STAINLESS STEEL

CLEVIS PIN: AISI TYPE 316 STAINLESS STEEL

Anchor Shackle

CATALOG NO. AS-1.0-SL-SS316

ULTIMATE BREAKING STRENGTH: 60,000 LBS.

DIMENSION IN INCHES: A = 3 1/2

B = 3/4

C = 1 1/4

E = 3/4

F = 1 7/8

G = 1

WEIGHT LBS./C: 242

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Machine Bolts - Square Head Stainless Steel

3/8 inch 4250 lbs.

1/2 inch 7800 lbs.

5/8 inch 12400 lbs.

3/4 inch 18350 lbs.

7/8 inch 25400 lbs.

Min. Tensile Strength

LENGTH MIN. THREAD APPX. SHIPPING

CAT. NO INCHES LENGTH INCHES WT. LBS. PER 100 PCS.

MBSA10 1 3/4 7

MBSB10 1-1/2 1 9

MBSC10 2 1 10

MBSD10 2-1/2 1 12

MBSE10 3 1-3/4 13

MBSF10 3-1/2 2 14

MBSG10 4 3 15

MBSH10 4-1/2 3 16

MBSI10 5 3 18

MBSJ10 5-1/2 3 19

3/8 INCH DIAMETER

1/2 INCH DIAMETER

LENGTH MIN. THREAD APPX. SHIPPING

CAT. NO. INCHES LENGTH INCHES WT. LBS. PER 100 PCS.

MBSA15 1 3/4 16

MBSB15 1-1/2 1-1/4 17

MBSC15 2 1-1/4 20

MBSD15 2-1/2 1-1/4 22

MBSE15 3 1-1/4 24

MBSF15 3-1/2 1-1/4 27

MBSG15 4 3 29

MBSH15 4-1/2 3 32

MBSI15 5 3 33

MBSJ15 5-1/2 3 39

MBSK15 6 3 39

MBSL15 6-1/2 3 41

MBSM15 7 3 44

MBSN15 8 4 49

MBSP15 9 4 53

MBSQ15 10 6 58

MBSR15 11 6 65

MBSS15 12 6 70

MBST15 14 6 75

MBSU15 16 6 85

MBSV15 18 6 92

MBSW15 20 6 103

5/8 INCH DIAMETER

LENGTH MIN. THREAD APPX. SHIPPING

CAT. NO. INCHES LENGTH INCHES WT. LBS. PER 100 PCS.

MBSA20 1 1 25

MBSB20 1-1/2 1-1/2 35

MBSC20 2 1-1/2 36

MBSD20 2-1/2 1-1/2 40

MBSE20 3 1-3/4 42

MBSF20 3-1/2 1-3/4 49

MBSG20 4 3 50

MBSH20 4-1/2 3 55

MBSI20 5 3 57

MBSK20 6 3 64

MBSM20 7 4 74

MBSN20 8 4 82

MBSP20 9 4 88

MBSQ20 10 6 96

MBSS20 12 6 110

MBST20 14 6 124

MBSU20 16 6 140

MBSV20 18 6 156

MBSW20 20 6 168

MBSX20 22 6 188

MBSY20 24 6 196

MBSZ20 26 6 228

3/4 INCH DIAMETER

LENGTH MIN. THREAD APPX. SHIPPING

CAT. NO. INCHES LENGTH INCHES WT. LBS. PER 100 PCS.

MBSC25 2 1-3/4 53

MBSD25 2-1/2 2-1/8 58

MBSE25 3 1-3/4 65

MBSF25 3-1/2 1-3/4 71

MBSK25 6 3 101

MBSM25 7 4 112

MBSN25 8 4 124

MBSQ25 10 6 146

MBSS25 12 6 168

MBST25 14 6 192

MBSU25 16 6 210

MBSV25 18 6 230

MBSW25 20 6 272

MBSX25 22 6 280

MBSY25 24 6 296

MBSZ25 26 6 316

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Double Arming Bolts Stainless Steel

· Rolled threads to assure uniformity and strength

· Cone points on all sizes

· Four regular square nuts furnished with each bolt.

5/8 INCH DIAMETER

LENGTH APPX. SHIPPING

CAT. NO. INCHES WT. LBS. PER 100 PCS.

DABA38 10 120

DABB38 12 132

DABC38 14 144

DABD38 16 164

DABE38 18 180

DABF38 20 192

DABG38 22 212

DABH38 24 224

DABI38 26 240

DABJ38 28 256

DABK38 30 280

DABL38 32 296

DABM38 34 298

DABN38 36 440

3/4 INCH DIAMETER

LENGTH APPX. SHIPPING

CAT. NO. INCHES WT. LBS. PER 100 PCS.

DABB39 12 204

DABC39 14 216

DABD39 16 244

DABE39 18 260

DABF39 20 280

DABG39 22 304

DABH39 24 324

DABI39 26 348

DABJ39 28 373

DABK39 30 390

DABL39 32 400

DABM39 34 420

DABN39 36 450

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Oval Eye Bolts Stainless Steel

Double Arming Eye Bolts Stainless Steel

5/8 inch 12400 lbs.

3/4 inch 18350 lbs.

Min. Tensile Strength

5/8 INCH DIAMETER

BOLT LENGTH THREAD LENGTH APPX. SHIPPING

CAT. NO. INCHES INCHES WT. LBS. PER 100 PCS.

OEB-5864 6 4 98

OEB-5884 8 4 114

OEB-5894 9 4 121

OEB-58106 10 6 132

OEB-58126 12 6 146

OEB-58146 14 6 160

OEB-58166 16 6 169

OEB-58186 18 6 187

OEB-58206 20 6 200

3/4 INCH DIAMETER

BOLT LENGTH THREAD LENGTH APPX. SHIPPING

CAT. NO. INCHES INCHES WT. LBS. PER 100 PCS.

OEB-3484 8 4 181

OEB-34106 10 6 205

OEB-34126 12 6 217

OEB-34146 14 6 235

OEB-34166 16 6 265

OEB-34186 18 6 282

5/8 INCH DIAMETER

BOLT LENGTH THREAD LENGTH APPX. SHIPPING

CAT. NO. INCHES INCHES WT. LBS. PER 100 PCS.

EBDA1412 14 12 185

EBDA1614 16 14 205

EBDA1816 18 16 216

EBDA2018 20 18 232

EBDA2220 22 20 251

EBDA2422 24 22 279

EBDA2624 26 24 288

3/4 INCH DIAMETER

BOLT LENGTH THREAD LENGTH APPX. SHIPPING

CAT. NO. INCHES INCHES WT. LBS. PER 100 PCS.

EBDA1614-75 16 14 312

EBDA1816-75 18 16 328

EBDA2018-75 20 18 358

EBDA2220-75 22 20 374

EBDA2422-75 24 22 389

EBDA2624-75 26 24 416

5/8 inch 12400 lbs.

3/4 inch 18350 lbs.

Min. Tensile Strength Length

Length

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Carriage Bolts Stainless Steel

Brace Bolts Stainless Steel

BRACE BOLTS HAVE ONE-PIECE WASHER

HEADS FOR WRENCHING, MAKING

RECLAIMING HARDWARE EASIER. BOLTS

ARE USED FASTENING A BRACE TO A

CROSS-ARM. EACH BOLT IS PROVIDED WITH

ONE SQUARE NUT. MINIMUM TENSILE

STRENGTH: 4,250 LBS.

CARRIAGE BOLTS ARE

STAINLESS STEEL ROLLED

THREADS WITH SQUARE

SHOULDERS. EACH BOLT IS

PROVIDED WITH ONE

SQUARE NUT.

3/8 INCH DIAMETER

BOLT LENGTH THREAD LENGTH APPX. SHIPPING

CAT. NO. INCHES INCHES WT. LBS. PER 100 PCS.

CBA32 3 2 12

CBA43 4 3 14

CBA453 4-1/2 3 16

CBA53 5 3 17

CBA553 5-1/2 3 18

CBA63 6 3 19

CBA73 7 3 22

CBA83 8 3 24

CBA106 10 6 29

CBA126 12 6 34

BOLT LENGTH THREAD LENGTH APPX. SHIPPING

CAT. NO. INCHES INCHES WT. LBS. PER 100 PCS.

CBA453-1/2 4-1/2 3 30

CBA53-5 5 3 32

CBA553-5 5-1/2 3 35

CBA63-5 6 3 36

CBA74-5 7 4 41

CBA84-5 8 4 46

CBA106-5 10 6 53

1/2 INCH DIAMETER

DIAMETER BOLT LENGTH THREAD LENGTH APPX. SHIPPING

CAT. NO INCHES INCHES INCHES WT. LBS. PER 100 PCS.

BBA452 3/8 4-1/2 2 22

3/8 inch 4250 lbs.

1/2 inch 7800 lbs.

Min. Tensile Strength

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

BONDING CLAMP

TYPE 316 Stainless Steel

CATALOG NO. BC-3/4HN-SS316

BONDING CLAMP FOR 3/4” HEX NUT

TYPE 316 STAINLESS STEEL WITH 3/16” HOLE ON CENTER

MADE FROM 1/16” THICK MATERIAL, TYPE 316 STAINLESS STEEL

1/16” THICK MATERIAL

TYPE 302/316 STAINLESS STEEL

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Angle Crossarm Braces Stainless Steel

The one-piece steel angle crossarm brace is used in the construction of heavy pole lines.

• Use ½ inch lag screws or bolts under the arm

• Use 5/8 inch through bolt at the pole

• Formed at pole mount hole with ample clearance for bolt tightening

Flat Crossarm Braces Stainless Steel

The steel flat crossarm brace is used to align and support crossarms.

• Rounded ends for safety

• Style A accommodates 3/8 and ½ inch lag screw or bolt

• Style B has offset ends to fit flat

• Style B accommodates ½ and 5/8 inch lag screw or bolt

APPX. SHIPPING

ANGLE SIZE A B WT. LBS. PER

CAT. NO. INCHES INCHES INCHES 100 PCS.

ACB-4212 1-1/2 X 1-1/2 X 3/16 42 12 800

ACB-4814 1-1/2 X 1-1/2 X 3/16 48 14 920

ACB-4818 1-1/2 X 1-1/2 X 3/16 48 18 1000

ACB-4918 1-1/2 X 1-1/2 X 3/16 slots 48 18 1000

ACB-6018 1-1/2 X 1-1/2 X 3/16 60 18 1130

ACB-6118 1-1/2 X 1-1/2 X 3/16 slots 60 18 1130

ACB-6218 1-3/4 X 1-3/4 X 3/16 60 18 1390

ACB-6620 1-3/4 X 1-3/4 X 3/16 66 20 1490

ACB-7222 1-3/4 X 1-3/4 X 3/16 72 22 1640

ACB-7322 2 X 2 X 3/16 72 22 1890

ACB-7422 2 X 2 X 3/16 slots 72 22 1890

ACB-7218 2 X 2 X 3/16 72 18 1780

ACB-8827 1-3/4 X 1-3/4 X 3/16 88 27-3/8 2010

TOTAL LENGTH STEEL SIZE APPROX. SHIPPING WT.

CAT.NO. INCHES STYLE INCHES LBS. PER 100 PCS

FCB-26 26 A 1/4 X 1-1/4 220

FCB-28 28 A 1/4 X 1-1/4 245

FCB-30 30 A 1/4 X 1-1/4 265

FCB-32 32 A 1/4 X 1-1/4 280

FCB-34 34 A 1/4 X 1-1/4 295

FCB-36 36 A 1/4 X 1-1/4 310

FCB-30B 30 B 1/4 X 1-1/2 320

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Alley Crossarm Braces Stainless Steel

The alley crossarm brace is used when a crossarm extends out on one side of a pole only.

Most come with a welded lineman step.

Smith Corner Brace Stainless Steel

The smith corner crossarm brace is used as a crossarm-to-crossarm support in double-dead-end construction. It is also used like the alley crossarm brace when a shorter length support is required.

• Manufactured from 1-3/4 x 1-3/4 x 3/16 inch steel angle

• All holes accommodate 5/8 inch bolts.

A B APPROX. SHIPPING WT.

CAT.NO. FIG. ANGLE SIZE INCHES INCHES INCHES LBS. PER 100 PCS.

ACB-96 A 2-1/2 X 2-1/2 X 3/16 96 3 2690

ACB-84 B 2-1/2 X 2-1/2 X 3/16 84 5 2600

ACB-120 B 2 X 2 X 1/4 120 6 2760

ACB-84L B 1-3/4 X 1-3/4 X 3/16 84 5 1750

A B APPX. SHIPPING WT.

CAT. NO. FEET INCHES LBS. PER 100 PCS.

SCB-54 4-1/2 3 1170

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Back Crossarm Brace Stainless Steel

The back crossarm brace is used to support a crossarm from the back side of the pole. It is manufactured from 1-3/4 x 1-3/ 4 x 3/16 inch steel angle with holes for 5/8 bolts.

Vertical Braces Stainless Steel

Vertical braces and vertical angle braces are used in a variety of ways to support crossarms.

• Brace from pole to arm

• Brace from arm to arm(s)

• Varying quantity of holes for 5/8 inch bolts in each brace

Contact factory for other configurations.

A B APPX. SHIPPING WT.

CAT. NO. INCHES INCHES LBS. PER 100 PCS.

BCB-37 37 2-1/2 770

ANGLE SIZE OVERALL NO. OF APPX. SHIPPING WT.

CAT. NO. INCHES LENGTH HOLES LBS. PER 100 PCS.

VB-262 1-1/2 X 1-1/2 X 3/16 26 2 430

VB-383 1-1/2 X 1-1/2 X 3/16 38 3 600

VB-382 1-1/2 X 1-1/2 X 3/16 38 2 610

VB-502 1-1/2 X 1-1/2 X 3/16 50 2 830

VB-516 1-1/2 X 1-1/2 X 3/16 51 6 1010

VB-823 2 X 2 X 1/8 82 3 1160

VB-843 2 X 2 X 3/16 84 3 1880

VB-1203 2 X 2 X 3/16 120 3 2680

VB-646 2 X 2 X 1/4 64 6 1830

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Double Arming Bracket Stainless Steel

The double arming bracket is used to increase the breaking strength of a double arm assembly.

It is used advantageously where a single guy wire is desirable on heavy dead-end loads.

• Cast of ductile iron

• Fits arms spaced from 7 to 10-3/4 inches apart

• Extension plate allows arm spacing to

17-3/4 inches

Service Brackets Stainless Steel

Service brackets support single or multiplex wires at the service entrance.

• Style 1 insulators are grey, dry process porcelain type

• Style 1 brackets may be installed without removing the bolts

• Style 2 is manufactured from steel channel and has three 3/8”-

16 threaded locations for up to 3 single house bracket insulators (not furnished)

• Back up bracket for style 2 is sold separately

APPX. SHIPPING

CAT. NO DESCRIPTION WT. LBS. PER 100 PCS.

DAB-1 DOUBLE ARMING BRACKET 620

DAB-2 2 DOUBLE ARMING BRACKETS ASSEMBLED 1200

DAB-2W/8 2 DOUBLE ARMING BRACKETS ASSEMBLED 1300

INCLUDING 4-5/8 X 6 INCH MOUNTING

BOLTS AND NUTS

DAB-EXT EXTENSION PLATE 470

FITS PIPE APPX. SHIPPING

CAT. NO. STYLE SIZES-INCHES WT. LBS. PER 100 PCS.

SBS-1 1 2-1/2 THRU 5 410

SBS-2 2 1 THRU 2-1/2 184

SBU 1 THRU 2-1/2 88

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Cutout Mounting Bracket TYPE 316 Stainless Steel

Cutout Combination Unit Mounting Brackets are engineered for strength and durability.

CATALOG NO. COB1-316

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Cable Extension Arms TYPE 316 Stainless Steel

Used to support a telephone cable at a distance from the pole. The messenger wire is held by a standard #TBC-1316SS Suspension Clamp which is bolted up against the under side of the angles by a stainless steel 5/8” machine bolt. The machine bolt goes between the legs of the two angles and permits adjustment. Mounting is accomplished by a 5/8” machine bolt at the upper position and ½” lag screw at the lower position.

STOCK NO. DESCRIPTION EXTENSION APPROX. WT.

LBS. 100 PCS.

CEA-1 3" X 2-1/2" X 1/4" Angle 17-1/2 to 26 3000

CEA-2 3-1/2" X 2-1/2" x 5/16" Angle 26-1/2 to 44-1/2 6000

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Cutout Mounting Bracket TYPE 316 Stainless Steel

Cutout Combination Unit Mounting Brackets are engineered for strength and durability.

CATALOG NO. COB1-316

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Insulator Support Angle Stainless steel

The insulator support angle mounts at the ends of a double arm and acts as a fastening point for suspension or pin-type insulators.

• Manufactured from 2-1/2 x 2-1/2 x ¼ inch steel angle

• All holes accommodate 5/8 inch bolts

Dead-End Clevis Stainless Steel

The clevis is used for attaching dead-end insulators and guys with connecting links.

• Manufactured from 3/16 x 1-1/2 inch flat steel

• May be ordered with a 5/8 inch galvanized cotter bolt with brass humpback cotter

OVERALL HOLES IN HOLES IN APPX. SHIPPING WT.

CAT. NO. LENGTH VERTICAL LEG HORIZONTAL LEG LBS. PER 100 PCS.

ISA 29 4 21 1090

COTTER A B HOLE APPX. SHIPPING WT.

CAT. NO. BOLT INCHES INCHES INCHES LBS. PER 100 PCS.

PEC-311 NO 3-1/2 1/4 11/16 79

PEC-313 NO 3-1/2 1/4 13/16 79

PEC-311C YES 3-1/2 1/4 11/16 85

PEC-411 NO 3-5/8 5/8 11/16 79

PEC-413 NO 3-5/8 5/8 13/16 79

PEC-411C YES 3-5/8 5/8 11/16 85

PEC-413C YES 3-5/8 5/8 13/16 85

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Eye Nut - Weldless TYPE 304/316 Stainless Steel

When Ordering Please Specify Alloy Type 304SS, T316SS Example: OEN12316SS

ROD MAX ROD MAX. PIN

CATALOG SIZE SIZE RATED TAKE- DIA. WEIGHT

NO. A NO. LOAD OUT C D E F G PER 100

OEN38SS 3/8 1 610 1-1/2 1-3/16 1/2 2 1-3/8 11/16 63

OEN12SS 1/2 1 1130 1-1/2 1-3/16 1/2 2 1-3/8 11/16 63

OEN58SS 5/8 1 1810 1-1/2 1-3/16 1/2 2 1-3/8 11/16 62

OEN34SS 3/4 1 2710 1-1/2 1-3/16 1/2 2 1-3/8 11/16 60

OEN78SS 7/8 2 3770 2 1-11/16 3/4 2-5/8 1-15/16 1 170

OEN1SS 1 2 4960 2 1-11/16 3/4 2-5/8 1-15/16 1 170

OEN114SS 1-1/4 3 8000 2-1/2 1-13/16 1 3-3/8 3 1-1/4 364

OEN112SS 1-1/2 3 11630 2-1/2 1-13/16 1 3-3/8 3 1-1/4 345

OEN134SS 1-3/4 4 15700 4 4 1-1/2 6-1/4 4 2-1/4 1638

OEN2SS 2 4 20700 4 4 1-1/2 6-1/4 4 2-1/4 1588

OEN214SS 2-1/4 4 27200 4 4 1-1/2 6-1/4 4 2-1/4 1538

OEN212SS 2-1/2 4 33500 4 4 1-1/2 6-1/4 4 2-1/4 1488

LOADS-DIMENSIONS-WEIGHTS

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Guy Hook MATERIAL SPECIFICATIONS: TYPE 316 Stainless Steel

• TWO SPURS TO RESIST POLE SPLITTING

• MORE SURFACE IN CONTACT WITH POLE THAN OTHER COMPARABLE GUY ATTACHMENTS –

GREATER PROTECTION TO WOOD FIBERS

• FOR ROUND OR FLAT SURFACES

• WILL INTERCEPT WIRE AT ANY ANGLE

GH2-316SS GH1-316SS

CATALOG MAXIMUM MOUNTING MINIMUM

NUMBER WIRE BOLTS A B C R ULTIMATE

LBS.

GH1-316SS 9/16" 5/8" - 3/4" 3" 5/8" 2-7/8" 3/4" 20,000

TOP- 1" - 7/8"

GH2-316SS 3/4" BOTTOM- 3/4" - 5/8" 4" 1" 3-7/16" 7/8" 25,000

AND/OR 1/2" L.S.

DIMENSIONS-INCHES

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Guying Hardware MATERIAL: TYPE 316 Stainless Steel

Angle Guy Attachments Made of flat steel. The strand bearing surface is rounded to provide protection to the strand without the use of a guy thimble

Figure 2-24

AGA-1-316SS

Figure 2-25

AGA2-316SS

Guy Hooks Made from half oval steel bent with flat side toward pole, the rounded side prevents injury to guy strand.

Figure 2-26 – GJH

Strain Plates Serve the same purpose as Guy Shims but offer greater pole protection. Made in two types; the Standard Type and the Combination Guy Hook and strain Plate Type. All types have 7/32” nail holes. No.

5728 has one 11/16” Guy Hook hole and two 7/16” lag screw holes.

Figure 2-27

SP1-316SS

Figure 2-28

SP2-316SS

Lift Plates Used under the eyes of straight and angle strand-eye bolts to relieve the load on the bolts.

Figure 2-29

LP1-316SS

Push Brace Bracket Made of heavy steel and welded prior to hot galvanizing. Brackets eliminate (1) gaining or mortising, (2) unnecessary digging and back filling, and (3) cutting and damaging treated surface of pole.

Figure 2-30

PBB-316SS

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Thimble Eye Nut MATERIAL: SPECIFICATIONS: TYPE 316 Stainless Steel

Guying Hardware (cont.)

CATALOG

NUMBER FOR BOLT DIA. A" B" C" D" E" F"

TEN-58316SS 5/8" 1-1/2" 1-1/2" 7/8" 1-3/8" 1-7/8" 3"

TEN-34316SS 3/4" 1-1/2" 1-1/2" 7/8" 1-3/8" 1-7/8" 3"

DIMENSIONS-INCHES

STOCK FIGURE DESCRIPTION APPROX. WT.

NO. NO. BOLT HOLE SIZE LBS. 100 PCS.

AGA1-316 2-24 1- BOLT TYPE 11/16 1/4 X 1 1/2 X 4 1/8 84

AGA12-316 2-24 1- BOLT TYPE 13/16 1/4 X 2 X 4 1/8 114

AGA2-316 2-25 2- BOLT TYPE 9/16-13/16 1/4 X 1 1/2 X 7 118

AGA22-316 2-25 2- BOLT TYPE 9/16-13/16 1/4 X 2 X 7 1/4 150

GJH 2-26 1- HOLE MOUNTING 11/16 3/8 X 1 3/4 X 4 84

SP1-316 2-27 STANDARD 7/32 14 GA X 4 X 8 74

SP2-316 2-28 GUY HOOK TYPE 7/32 14 GA X 4 X 8 154

LP12-316 2-29 5/8 BOLT-2 HOLE 11/16 X 15/16 3/16 X 2 1/2 X 7 90

LP13-316 2-29 5/8 BOLT-3 HOLE 11/16 X 15/16 3/16 X 2 1/2 X 7 86

LP22-316 2-29 3/4 BOLT-2 HOLE 13/16 X 1 1/16 1/4 X 2 1/2 X 7 119

LP23-316 2-29 3/4 BOLT-3 HOLE 13/16 X 1 1/16 1/4 X 2 1/2 X 7 115

PBB-316 2-30 11/16 - 1300

LIFT PLATES

PUSH BRACE BRACKET

DIMENSIONS-INCHES

GUY HOOKS

ANGLE GUY ATTACHMENTS

STRAIN PLATES

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Insulator Support Angle Stainless steel

The insulator support angle mounts at the ends of a double arm and acts as a fastening point for suspension or pin-type insulators.

• Manufactured from 2-1/2 x 2-1/2 x ¼ inch steel angle

• All holes accommodate 5/8 inch bolts

Dead-End Clevis Stainless Steel

The clevis is used for attaching dead-end insulators and guys with connecting links.

• Manufactured from 3/16 x 1-1/2 inch flat steel

• May be ordered with a 5/8 inch galvanized cotter bolt with brass humpback cotter

OVERALL HOLES IN HOLES IN APPX. SHIPPING WT.

CAT. NO. LENGTH VERTICAL LEG HORIZONTAL LEG LBS. PER 100 PCS.

ISA 29 4 21 1090

COTTER A B HOLE APPX. SHIPPING WT.

CAT. NO. BOLT INCHES INCHES INCHES LBS. PER 100 PCS.

PEC-311 NO 3-1/2 1/4 11/16 79

PEC-313 NO 3-1/2 1/4 13/16 79

PEC-311C YES 3-1/2 1/4 11/16 85

PEC-411 NO 3-5/8 5/8 11/16 79

PEC-413 NO 3-5/8 5/8 13/16 79

PEC-411C YES 3-5/8 5/8 11/16 85

PEC-413C YES 3-5/8 5/8 13/16 85

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Lag Screws, Screw Eye Bolts Stainless Steel

Screw Bolts Stainless Steel

CATALOG NO. MIN. THREAD APPROX.

FETTER DRIVE FETTER DRIVE TWIST DRIVE SIZE LENGTH SHIP WT.

GIMLET POINT REG. POINT PILOT POINT PILOT POINT (INCH) (INCH) (LBS/100)

LS-415G 1/4 X 1-1/2 1-1/4 2.4

LS-420G LS-420 1/4 X 2 1-1/2 2.7

LS-425G LS-425 1/4 X 2-1/2 1-3/4 3.3

LS-430G 1/4 X 3 2 3.7

LS-525G 5/16 X 2-1/2 1-3/4 5.3

LS-625 3/8 X 2-1/2 1-3/4 8.8

LS-630G LS-630 LS-630P 3/8 X 3 2 9.9

KS-640 KS-640P 3/8 X 4 2-1/2 13

LS-830 LS-830P LS-830TP 1/2 X 3 2 19

LS-835 LS-835P 1/2 X 3-1/2 2-1/4 20

LS-840G LS-840 LS-840P LS-840TP 1/2 X 4 2-1/2 23

LS-845 LS-845P 1/2 X 4-1/2 2-3/4 26

LS-850 LS-850P LS-850TP 1/2 X 5 3 27

LS-1050 5/8 X 5 3 44

CATALOG DIAMETER APPROX. SHIP WT.

NO. (INCH) (LBS/100)

SEB-860 1/2 53

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Multi-Helix Roundshaft Anchors TYPE 316 Stainless Steel

Guy Attachment with High Strength bolt

TYPE 316 STAINLESS STEEL

Helixes No Eyenut Single Eye Double Eye Triple Eye

1-8",10", & 12" THMA-316SS THMAS-316SS THMAD-316SS THMAT-316SS

Three 10" THMA-10-316SS THMA-10S-316SS THMA-10D-316SS THMA-10T-316SS

TRIPLE HELIX

ASE-50316SS

ASE-70316SS

ASE-100316SS

3.5'

1 1/4" ROUND with upset Coupling and High Strength Bolt

ANCHOR SHAFT EXTENSIONS

Length Catalog No.

5'

7'

10'

ASE-3.5316SS

Single Eye with Upset Coupling

Description Catalog No.

GAU-1316SS

(above for 1 1/2" Square and 1/14" Round)

GAU-2316SS

GAU-3316SS

Double Eye with Upset Coupling

Triple Eye with Upset Coupling

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Nuts Stainless Steel Stainless Steel Hardware

Washers Stainless Steel

USED WITH BOLTS

ON CROSSARMS AND

POLES

REGULAR SQUARE

FITS BOLT APPX. SHIPPING

CAT. NO. SIZES INCHES WT. LBS. PER 100 PCS.

SN-38 3/8 3

SN-12 1/2 5

SN-58 5/8 10

SN-34 3/4 15

SN-78 7/8 25

REGULAR HEX

HN-38 3/8 1.6

HN-12 1/2 3.75

HN-58 5/8 7.33

HN-34 3/4 11.9

HN-78 7/8 19.0

FITS BOLT WASHER APPX. SHIPPING

CAT. NO SIZES - INCHES SIZE - INCHES WT. LBS. PER 100 PCS.

RW-38 3/8 1"DIA.-7/16" HOLE 1.6

RW-12 1/2 1-3/8" DIA.-9/16" HOLE 3.9

RW-58 5/8 1-3/4" DIA.-11/16" HOLE 7

RW-34 3/4 2" DIA.-13/16" HOLE 10

RW-78 7/8 2-1/4" DIA.-15/16" HOLE 18

RW-100 1 2-1/2" DIA.-1-1/16" HOLE 20

LW-38 3/8 SINGLE COIL 2

LW-12 1/2 SINGLE COIL 2

LW-58 5/8 SINGLE COIL 3

LW-34 3/4 SINGLE COIL 5

WIDTH DIA. HOLE THICKNESS APPX. SHIPPING

(INCH) (INCH) (INCH) WT. LBS. PER 100 PCS.

Flat

SW-582 2 9/16 1/8 13

SW-122 2 11/16 1/8 13

SW-1222 2-1/4 11/16 3/16 23

SW-3422 2-1/4 13/16 3/16 23

SW-784 4 7/8 3/16 75

SW-1184 4 1-1/8 1/4 194

Curved

CW-123 3 11/16 1/4 57

CW-1222 2-1/4 11/16 3/16 23

CW-343 3 13/16 1/4 56

SPLIT LOCK

ROUND

SQUARE

FA461018R0014

se ll W ell s

2-32ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Two Hole Pipe Straps TYPE 304 and 316 Stainless Steel

MATERIAL:

TYPE 304 or TYPE 316 STAINLESS STEEL

WHEN ORDERING:

SPECIFY NAME, NUMBER, PIPE SIZE AND

MATERIAL.

DIMENSIONS (INCHES)

LOAD APPRX

CATALOG PIPE HOLE STOCK RATING WEIGHT

NO. SIZE A B C SIZE SIZE LBS. PER 100

50B08-SS 1/2 4-1/8 7/16 2-7/8 7/16 1/8 X 1-1/4 410 21

50B09-SS 3/4 4-5/16 9/16 3-1/16 7/16 1/8 X 1-1/4 410 24

50B10-SS 1 4-9/16 11/16 3-5/16 7/16 1/8 X 1-1/4 410 26

50B11-SS 1-1/4 4-15/16 13/16 3-11/16 7/16 1/8 X 1-1/4 410 30

50B12-SS 1-1/2 5-3/16 15/16 3-15/16 7/16 1/8 X 1-1/4 410 33

50B14-SS 2 5-3/4 1-1/8 4-1/2 7/16 1/8 X 1-1/4 410 38

50B16-SS 2-1/2 6-1/4 1-3/8 5 7/16 1/4 X 1-1/4 610 85

50B18-SS 3 6-7/8 1-3/4 5-5/8 7/16 1/4 X 1-1/4 610 100

50B19-SS 3-1/2 7-3/8 2 6-1/8 7/16 1/4 X 1-1/4 610 111

50B22-SS 4 8-3/8 2-1/4 7-1/8 9/16 1/4 X 1-1/2 725 151

50B26-SS 5 9-7/16 2-3/4 8-3/16 9/16 1/4 X 1-1/2 725 179

50B30-SS 6 10-1/2 3-5/16 9-1/4 9/16 1/4 X 1-1/2 725 207

50B32-SS 8 14 4-5/16 12 11/16 3/8 X 1-1/2 900 415

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Pole-Top Extension Stainless Steel

The steel pole-top extension solves the problem of installing new primary circuits on established poles.

• Used in pairs

• Use with the heel plate shown below

• All holes accommodate 5/8 inch bolts

Heel Plate Stainless Steel

The steel heel plate is used with the pole-top extensions to improve rigidity.

• Center hole is used to attach flat brace or 18 inch drop angle cross arm brace

• Fits top pole diameters from 5 to 13 inches

APPX. SHIPPING WT.

CAT. NO MATERIAL LBS. PER 100 PCS.

HP-125 1-4" PLATE 500

ANGLE

SIZE APPX. SHIPPING WT.

CAT. NO. LENGTH INCHES A B C D LBS. PER 100 PCS.

PTE-87 7' 3-1/2" 3 X 3 X 1/4 24 17-3/4 - 2 3920

PTE-148 12' 4" 3 X 3 X 1/4 33 24 30 2 6650

INCHES

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

ADSCO

STAINLESS STEEL DEAD-END GRIPS

FOR USE ON STAINLESS STEEL STRAND: TYPE 302

FOR USE ON STAINLESS STEEL STRAND: TYPE 316

Catalog Applied Subset Rod Color Rated Number Size Units Wt/Lbs. Length Diameter Code Strength Size Type

AG-807 1/4" 100 59 28 4 .100 Yellow 9,500 1/4" 3W-7W

AG-808 9/32" 100 58 27 4 .100 Black 10,500 9/32" 3W-7W

AG-809 5/16" 50 40 31 5 .100 Orange 13,200 5/16" 3W-7W

AG-810 3/8" 50 62 37 5 .114 Green 18,000 3/8" 3W-7W

AG-811 7/16" 25 55 43 5 .138 Red 27,000 7/16" 3W-7W

AG-812 1/2" 20 60 50 6 .138 Blue 32,000 1/2" 7W-19W

AG-813 9/16" 10 50 60 6 .162 Yellow 36,000 9/16" 7W-19W

TYPE 302 STAINLESS STEEL ADSCO DEAD-ENDS

Per Carton Strand

Catalog Applied Subset Rod Color Rated Number Size Units Wt/Lbs. Length Diameter Code Strength Size Type

AG-907 1/4" 100 53 26 4 .100 Yellow 7,500 1/4" 3W-7W

AG-908 9/32" 100 58 27 4 .100 Black 9,550 9/32" 3W-7W

AG-909 5/16" 50 41 31 5 .100 Orange 11,500 5/16" 3W-7W

AG-910 3/8" 50 62 37 5 .114 Green 16,200 3/8" 3W-7W

AG-911 7/16" 25 55 43 5 .138 Red 24,000 7/16" 3W-7W

AG-912 1/2" 20 60 50 6 .138 Blue 30,000 1/2" 7W-19W

AG-913 9/16" 10 50 60 6 .162 Yellow 33,000 9/16" 7W-19W

Per Carton Strand

TYPE 316 STAINLESS STEEL ADSCO DEAD-ENDS

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

MATERIALS:

Grip – made of the same basic material as the strand they are designed for.

Identification Tag – shows catalog number, nominal strand size and strand diameter range.

Color Code – identifies correct strand sizes.

Cross over marks – mark A shows starting point for application on small diameter terminations. Mark B shows starting point for application on larger diameter terminations described on page 2.

GENERAL RECOMMENDATIONS

POWER GRIP DEAD ENDS are recommended for single wood poles associated with distribution construction and for guying transmission towers.

They are compatible to the strand and are ideal for use in coastal areas and in polluted areas.

APPLICATION INSPECTION

DEAD ENDS may be removed and re-applied a maximum of 3 times during new construction with-out damaging their performance characteristics, however they should not be reused after original installation.

DEAD ENDS are designed generally to hold the full rated strength of 90 to 110 ton of grade galvanized steel strand.

DEAD ENDS should be used on hardware that is held in a fixed position; the fitting should not be allowed to rotate or spin about the axis of the strand.

Further, they should not be used as tools; such as come-alongs, pulling-in grips, etc.

Lay direction of both the DEAD END and the strand should be the same. In most cases left hand lay is standard. For appearance and safety, the stranded tail should be cut as close as convenient to the cross over mark. If desired the strand tail can, instead, extend through the loop for grounding purposes.

DEAD ENDS retain a positive grip under all conditions whether the guy is relaxed or under tension. Once the legs of the DEAD END are in position, the assembly is complete and permanent.

DEAD ENDS will remain fully operative under the most difficult conditions, tension, impact, temperature extremes, in fact, any force to be met in functional performance. They will never relinquish their gripping power.

POWER

GRIP DEAD END

IDENTIFICATION

TAG

CABLED LOOP

COLOR CODE AND

CROSS OVER MARKS

LONG LEG

SHORT LEG

A B

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Lag Screws, Screw Eye Bolts Stainless Steel

Screw Bolts Stainless Steel

CATALOG NO. MIN. THREAD APPROX.

FETTER DRIVE FETTER DRIVE TWIST DRIVE SIZE LENGTH SHIP WT.

GIMLET POINT REG. POINT PILOT POINT PILOT POINT (INCH) (INCH) (LBS/100)

LS-415G 1/4 X 1-1/2 1-1/4 2.4

LS-420G LS-420 1/4 X 2 1-1/2 2.7

LS-425G LS-425 1/4 X 2-1/2 1-3/4 3.3

LS-430G 1/4 X 3 2 3.7

LS-525G 5/16 X 2-1/2 1-3/4 5.3

LS-625 3/8 X 2-1/2 1-3/4 8.8

LS-630G LS-630 LS-630P 3/8 X 3 2 9.9

KS-640 KS-640P 3/8 X 4 2-1/2 13

LS-830 LS-830P LS-830TP 1/2 X 3 2 19

LS-835 LS-835P 1/2 X 3-1/2 2-1/4 20

LS-840G LS-840 LS-840P LS-840TP 1/2 X 4 2-1/2 23

LS-845 LS-845P 1/2 X 4-1/2 2-3/4 26

LS-850 LS-850P LS-850TP 1/2 X 5 3 27

LS-1050 5/8 X 5 3 44

CATALOG DIAMETER APPROX. SHIP WT.

NO. (INCH) (LBS/100)

SEB-860 1/2 53

FA461018R0014

se ll W ell s

2-35ADSCO LINE PRODUCTS 03/02 Please call for pricing.

SPECIFICATIONS

MATERIAL: BODY - AISI TYPE 316 STAINLESS STEEL

COTTER PIN: STAINLESS STEEL

Socket Eye

CATALOG NO. SE-30M-SS316

ULTIMATE BREAKING STRENGTH: 30,000 LBS.

DIMENSION IN INCHES: W = 1

R = 13/16

L = 2 1/16

DIA = 11/16

WEIGHT LBS./C: 1.40

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Strand-Eye Anchor Rods TYPE 316 Stainless Steel

Rolled threads are furnished on all rods up to and including ¾” diameter. 1” and larger have cut threads. Length of thread –3-1/2”. Manufactured to ANSI Standards.

STOCK LGTH APPROX. WT. STOCK LGTH APPROX. WT. STOCK LGTH APPROX. WT.

NO. FT. LBS. PER 100 PCS. NO. FT. LBS. PER 100 PCS. NO. FT. LBS. PER 100 PCS.

AR1-125316 5 300 - - - - - -

AR1-126316 6 450 - - - - - -

AR1-127316 7 500 - - - - - -

AR1-585316 5 590 - - - - - -

AR1-586316 6 664 AR2-586316 6 690 - - -

AR1-587316 7 766 AR2-587316 7 765 - - -

AR1-588316 8 830 AR2-588316 8 840 - - -

AR1-346316 6 960 AR2-346316 6 970 - - -

AR1-347316 7 1230 AR2-347316 7 1130 AR3-347316 7 1130

AR1-348316 8 1245 AR2-348316 8 1403 AR3-348316 8 1255

- - - AR2-349316 9 1460 AR3-349316 9 1460

- - - AR2-3410316 10 1520 - - -

AR1-108316 8 2300 AR2-108316 8 2310 AR3-108316 8 2310

- - - AR2-109316 9 2530 - - -

AR1-1010316 10 2600 AR2-1010316 10 2895 AR3-1010316 10 2895

- - - AR2-11410316 10 4400 AR3-11410316 10 4620

5/8" Diameter Rod --- Minimum Strength 16,000 Lbs.

3/4" Diameter Rod --- Minimum Strength 23,000 Lbs.

1" Diameter Rod --- Minimum Strength 36,000 Lbs.

1 1/4" Diameter Rod --- Minimum Strength 58,000 Lbs.

SINGLE EYE-Figure 2-6 DOUBLE EYE-Figure 2-7 TRIPLE EYE-Figure 2-8

1/2" Diameter Rod --- Minimum Strength 10,000 Lbs.

Figure 2-6 Figure 2-7

Figure 2-8

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Thimble Eye Nut MATERIAL: SPECIFICATIONS: TYPE 316 Stainless Steel

Guying Hardware (cont.)

CATALOG

NUMBER FOR BOLT DIA. A" B" C" D" E" F"

TEN-58316SS 5/8" 1-1/2" 1-1/2" 7/8" 1-3/8" 1-7/8" 3"

TEN-34316SS 3/4" 1-1/2" 1-1/2" 7/8" 1-3/8" 1-7/8" 3"

DIMENSIONS-INCHES

STOCK FIGURE DESCRIPTION APPROX. WT.

NO. NO. BOLT HOLE SIZE LBS. 100 PCS.

AGA1-316 2-24 1- BOLT TYPE 11/16 1/4 X 1 1/2 X 4 1/8 84

AGA12-316 2-24 1- BOLT TYPE 13/16 1/4 X 2 X 4 1/8 114

AGA2-316 2-25 2- BOLT TYPE 9/16-13/16 1/4 X 1 1/2 X 7 118

AGA22-316 2-25 2- BOLT TYPE 9/16-13/16 1/4 X 2 X 7 1/4 150

GJH 2-26 1- HOLE MOUNTING 11/16 3/8 X 1 3/4 X 4 84

SP1-316 2-27 STANDARD 7/32 14 GA X 4 X 8 74

SP2-316 2-28 GUY HOOK TYPE 7/32 14 GA X 4 X 8 154

LP12-316 2-29 5/8 BOLT-2 HOLE 11/16 X 15/16 3/16 X 2 1/2 X 7 90

LP13-316 2-29 5/8 BOLT-3 HOLE 11/16 X 15/16 3/16 X 2 1/2 X 7 86

LP22-316 2-29 3/4 BOLT-2 HOLE 13/16 X 1 1/16 1/4 X 2 1/2 X 7 119

LP23-316 2-29 3/4 BOLT-3 HOLE 13/16 X 1 1/16 1/4 X 2 1/2 X 7 115

PBB-316 2-30 11/16 - 1300

LIFT PLATES

PUSH BRACE BRACKET

DIMENSIONS-INCHES

GUY HOOKS

ANGLE GUY ATTACHMENTS

STRAIN PLATES

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Transformer Brackets Stainless Steel

These brackets support two transformers.

• Manufactured from flat steel welded onto a rigid frame

• Mounting slots accommodate ¾ inch bolts

• 1600 pound maximum total weight allowed

These brackets support three transformers and have these features.

• Extremely stable mounting on the pole

• Angled to have an aesthetically pleasing appearance

• Reversible plastic or steel mounting blocks that allow mounting transformers with 11-1/4 or 23-1/4 inch spacing between hanger brackets

• 1400 pounds maximum transformer weight at each position

• Allows pre assembly of all equipment and connections on the ground before being easily raised into place

A B R APPX. SHIPPING WT.

CAT. NO. INCHES INCHES INCHES LBS. PER 100 PCS.

TB-6375 26 6-3/8 4 2900

TB-400 26 4 4 2150

A B APPX. SHIPPING WT.

CAT. NO. INCHES INCHES LBS. PER 100 PCS.

CTB-43 43 60 11,500

CTB-21 21-1/2 60 11,500

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Turnbuckles - DROP FORGED

DROP FORGED HEX BODY

STAINLESS STEEL

1035 STEEL • 5:1 SAFETY FACTOR

USE FOR STRAIGHT OR IN-LINE PULLS ONLY

STUB ENDS

HOOK & HOOK

EYE & EYE JAW & JAW

HOOK & EYE

JAW & EYE

N O

T E

U

S E

W E

IG

H

T S

O F

E Y

E

E Y

E T

U R

N B

U C

K

LE

S T

O G

E T

A P

P R

O X

IM

A

T E

W E

IG

H

T S

O F

S T

U B

E N

D T

U R

N B

U C

K

LE

S

Federal Specifications FF-T-791 b Type 1 Form-1 Class 4

Federal Specifications FF-T-791 b Type 1 Form-1 Class 7

Federal Specifications FF-T-791 b Type 1 Form-1 Class 3

Federal Specifications FF-T-791 b Type 1 Form-1 Class 6

Federal Specifications FF-T-791 b Type 1 Form-1 Class 5

Federal Specifications FF-T-791 b Type 1 Form-1 Class 8

DIAMETER Avg. OVERALL

& TAKE-UP ends in closed with HOOKS JAW JAW in Inches position (in Inches) or EYES and EYE and JAW

1/4 x 4 8-1/4 .30 .32 .36

5/16 x 4-1/2 9-9/16 .63 .47 .52

3/8 x 6 11-7/8 .75 .76 .81

1/2 x 6 13-5/16 1.60 1.53 1.50

1/2 x 9 16-5/16 1.83 1.71 1.74

1/2 x 12 19-5/16 2.25 2.06 2.40

5/8 x 6 15-1/2 2.75 2.35 3.02

5/8 x 9 18-1/2 3.13 3.06 3.31

5/8 x 12 21-1/2 3.50 3.78 4.00

3/4 x 6 17 3.89 4.00 4.11

3/4 x 9 20 4.61 4.75 5.10

3/4 x 12 23 5.43 5.36 5.65

3/4 x 18 29 7.25 7.00 7.00

7/8 x 12 24-5/8 8.10 8.00 8.17

7/8 x 18 30-5/8 9.25 9.75 9.00

1 x 6 20-5/8 9.33 9.00 9.75

1 x 12 26-5/8 11.93 11.20 12.00

1 x 18 32-5/8 14.00 13.30 14.00

1 x 24 38-5/8 17.25 17.00 17.00

1-1/4 x 12 29-7/8 18.00 20.00 21.50

1-1/4 x 18 35-7/8 23.00 24.18 25.50

1-1/4 x 24 41-7/8 27.00 27.50 28.70

1-1/2 x 12 32-3/8 27.50 28.50 30.05

1-1/2 x 18 38-3/8 31.00 35.00 34.25

1-1/2 x 24 44-3/8 37.50 38.73 40.67

1-3/4 x 18 41-3/4 52.50 53.75 55.04

1-3/4 x 24 47-3/4 58.00 61.00 63.36

2 x 24 51-3/4 85.25 89.00 94.00

2-1/2 x 24 58-1/2 144.25 150.00 165.00

2-3/4 x 24 61-1/2 194.00 183.00 198.00

WEIGHT EACH in Lbs.

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Turnbuckles - ENGINEERING DATA Dimensions and Strength

PROOF LOAD TWICE SAFE WORKING LOAD

ULTIMATE LOAD FIVE TIMES SAFE WORKING LOAD

Dimension “W” figured with stub screwed in as shown. To determine the overall length of longer takeup turnbuckles, add the difference in takeup.

SAFE working

LOAD

A B C D E F G H in Lbs.

1/4 5/8 1/4 13/32 9/32 1/2 1-5/8 5/8 500

5/16 7/8 1/4 15/32 9/32 1/2 2 11-16 800

3/8 7/8 5/16 1/2 5/16 19/32 2-3/16 13/16 1 200

1/2 1-1/16 3/8 5/8 13-32 3/4 2-3/4 1 2 200

5/8 1-5/16 1/2 3/4 1/2 1-1/32 3-1/2 1-5/16 3 500

3/4 1-1/2 5/8 15/16 9/16 1-9/32 4-1/8 1-5/8 5 200

7/8 1-3/4 3/4 1-1/8 11/16 1-15/32 4-27/32 1-7/8 7 200

1 2-1/16 7/8 1-3/16 25/32 1-21/32 5-17/32 2-1/8 10 000

1-1/4 2-13/16 1-1/8 1-3/4 1 2-3/32 7-3/16 2-5/8 15 200

1-1/2 2-13/16 1-3/8 2-1/16 1-1/16 2-15/32 7-7/8 3-1/8 21 400

1-3/4 3-3/8 1-5/8 2-3/8 1-1/4 2-29/32 9-3/8 3-1/2 28 000

2 3-11/16 2 2-1/2 1-9/16 3-17/32 10-7/8 4-3/16 37 000

2-1/2 4-7/16 2-1/4 2-7/8 1-9/16 4-5/8 13-11/32 5-5/8 60 000

2-3/4 4-3/16 2-3/4 3-1/2 1-5/8 5-3/8 15 6-1/8 75 000

DIMENSIONS in Inches

SAFE working

A B C D E LOAD in Lbs.

1/4 11/32 7/32 25/32 1-25/32 500

5/16 7/16 9/32 15/16 2-3/16 800

3/8 17/32 11/32 1-1/8 2-9/16 1 200

1/2 23/32 7/16 1-7/16 3-7/32 2 200

5/8 7/8 1/2 1-3/4 3-7/8 3 500

3/4 1 5/8 2-1/8 4-11/16 5 200

7/8 1-1/4 3/4 2-3/8 5-1/4 7 200

1 1-7/16 7/8 3 6-3/8 10 000

1-1/4 1-13/16 1-1/8 3-9/16 7-3/4 15 200

1-1/2 2-1/8 1-1/4 4-1/8 8-5/8 21 400

1-3/4 2-3/8 1-1/2 4-11/16 10 28 000

2 2-11/16 1-3/4 5-3/4 12-1/8 37 000

2-1/2 3-1/8 2 6-1/2 13-9/16 60 000

2-3/4 3-1/4 2-1/4 7 15 75 000

DIMENSIONS in Inches

SAFE working

A B C D E LOAD in Lbs.

1/4 1/4 13/32 29/64 1-21/32 400

5/16 5/16 1/2 1/2 1-31/32 700

3/8 3/8 39/64 9/16 2-23/64 1 000

1/2 1/2 25/32 21/32 2-15/16 1 500

5/8 5/8 1 27/32 3-11/16 2 250

3/4 3/4 1-13/64 63/64 4-33/64 3 000

7/8 7/8 1-3/8 1-1/8 5-3/16 4 000

1 1 1-17/32 1-1/4 5-27/32 5 000

1-1/4 1-1/4 1-13/16 1-1/2 7-7/32 5 000

1-1/2 1-5/16 1-3/4 1-7/8 8-11/32 7 500

DIMENSIONS in Inches

SAFE working

A R S T U W LOAD in Lbs.

1/4 4 4-3/4 3/8 2-5/8 10 500

5/16 4-1/2 5-7/16 15/32 2-21/32 10-3/4 800

3/8 6 7-1/8 9/16 4-7/16 16 1 200

1/2 6 7-1/2 3/4 4-1/4 16 2 200

5/8 6 7-7/8 15/16 4-1/16 16 3 500

3/4 6 8-1/4 1-1/8 4-3/8 17 5 200

7/8 6 8-5/8 1-5/16 4-11/16 18 7 200

1 6 9 1-1/2 5 19 10 000

1-1/8 6 9-1/8 1-9/16 4-15/16 19 12 400

1-1/4 6 9-1/8 1-9/16 5-7/16 20 15 200

1-3/8 6 9-3/4 1-7/8 5-3/8 20-1/2 18 000

1-1/2 6 9-3/4 1-7/8 5-3/8 20-1/2 21 400

1-5/8 6 10-3/8 2-3/16 5-5/16 21 25 000

1-3/4 6 10-3/8 2-3/16 5-13/16 22 28 000

2 6 11 2-1/2 6 23 37 000

2-1/2 6 13-1/2 3-3/4 6-1/4 26 60 000

2-3/4 24 31-1/2 3-3/4 6-1/2 44-1/2 75 000

DIMENSIONS in Inches

JAW

EYE

HOOK

STUB END

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Turnbuckles - Eye and Eye TYPE 316 Stainless Steel

Sail Guide with Ring TYPE 316 Stainless Steel

Other Sizes & Types - Call for Price

ADSCO PART SCREW CLOSED STD.

NUMBER DIA. LENGTH PKG.

TB3/16X23/4SS316 3/16" 2-3/4" 1

TB1/4X31/2SS316 1/4" 3-1/2" 1

TB5/16X43/4SS316 5/16" 4-3/4" 1

ADSCO PART STD.

NUMBER PKG

AKS-46-01 5

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Stainless Steel Wire Rope Clips TYPE 304 AND 316 (Drop Forged)

*Based on clean, unlubricated threads.

Minimum torque required to reach max. holding power

RIGHT WAY FOR MAXIMUM ROPE STRENGTH

When using U-bolt clips, extreme care must be exercised to make certain that they are attached correctly. The correct way to attach U-bolts is shown above; the “U” section is in contact with the ropes “dead-end” and is clear of the thimble. The “live-end”, carrying the load is gripped by the saddle of the clip. Also, the tightening and retightening of the nuts must be accomplished as required.

Caution: Never use any wire rope clip to directly connect two straight lengths of wire rope.

Minimum

HOW TO SIZE Number Torque Approx.

ORDER of Clips in Lbs. Ft Weight

Required Each

To order 1/8" 2 4.5 .05lbs use the 3/16" 2 7.5 .106

Prefix: 1/4" 2 15 .19

WRC-Size 5/16" 2 30 .30 followed 3/8" 2 45 .46 by SS- 1/2" 3 65 .68

T304 or 316 5/8" 3 95 1.0

Example: 3/4" 4 130 1.5

WRC-1/2SS304 1" 5 225 2.69

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

WIRE ROPE WEIGHT

DIA. SIZE EACH

in Inches A B C D E F in Lbs.

1/8 1-15/16 1-1/16 1-5/16 11/16 5/32 5/8 3.3

3/16 1-15/16 1-1/16 1-5/16 11/16 7/32 5/8 3.3

1/4 1-15/16 1-1/16 1-5/16 11/16 9/32 5/8 3.3

5/16 2-1/8 1-1/4 1-1/2 13/16 3/8 3/4 4

3/8 2-3/8 1-15/32 1-5/8 15/16 7/16 7/8 7.50

1/2 2-3/4 1-3/4 1-7/8 1-1/8 9/16 1-1/16 18.80

5/8 3-1/2 2-3/8 2-1/4 1-3/8 11/16 1-1/4 36.

3/4 3-3/4 2-11/16 2-1/2 1-5/8 13/16 1-1/2 60.

7/8 5 3-3/16 3-1/2 1-7/8 15/16 1-3/4 90.

1 5-11/16 3-3/4 4-1/4 2-1/2 1-1/16 2-3/8 105.

1-1/8-1-1/4 6-1/4 4-5/16 4-1/2 2-3/4 1-5/16 2-5/8 166.

1-1/2 7-1/2 5-3/8 5 3-1/4 1-9/16 3-1/8 325.

1-3/4 10-3/4 7-1/4 7-1/4 4-1/4 1-7/8 4-1/8 583.25

2 10-3/4 7-1/4 7-1/4 4-1/4 2-1/8 4-1/8 583.25

DIMENSIONS IN INCHES

Wire Rope Thimbles Stainless Steel

HEAVY DUTY

STANDARD

PER FED. SPEC. FF-T-276B, TYPE III • ALSO AVAILABLE WITH WELDED GUSSET

WELDED GUSSET PLATES AVAILABLE FOR GUSSET 2”, 2 1/4”, AND 2 1/2”

MEETS FEDERAL SPECIFICATIONS FF-T-276B, TYPE II

WIRE ROPE MAX. PIN WEIGHT

DIA. SIZE DIA. per 100 in Inches A B C D E F in Inches in Lbs.

1/4 2-3/16 1-1/2 1-5/8 7/8 13/32 9/32 13/16 6.5

5/16 2-1/2 1-13/16 1-7/8 1-1/16 1/2 11/32 15/16 11.25

3/8 2-7/8 2-1/8 2-1/8 1-1/8 21/32 13/32 1-1/16 25.00

7/16 3-1/4 2-3/8 2-3/8 1-1/4 3/4 15/32 1-3/16 50.00

1/2 3-5/8 2-3/4 2-3/4 1-1/2 27/32 17/32 1-7/16 51.00

9/16 3-5/8 2-11/16 2-3/4 1-1/2 29/32 19/32 1-7/16 51.00

5/8 4-1/4 3-1/8 3-1/4 1-3/4 1 21/32 1-5/8 75.00

3/4 5 3-3/16 3-3/4 2 1-1/4 25/32 1-7/8 147.00

7/8 5-1/2 4-1/4 4-1/4 2-1/4 1-3/8 15/16 2-1/8 175.00

1 6-1/8 4-15/16 4-1/2 2-1/2 1-9/16 1-1/16 2-3/8 275.00

1-1/8-1-1/4 7 5-7/8 5-1/8 2-7/8 1-7/8 1-5/16 2-3/4 400.00

1-1/4-1-3/8 9-1/16 6-13/16 6-1/2 3-1/2 2-1/4 1-7/16 3-1/4 817.00

1-3/8-1-1/2 9 7-1/8 6-1/4 3-1/2 2-5/8 1-9/16 3-3/8 1175.00

1-5/8 11-1/4 8-1/8 8 4 2-3/4 1-23/32 3-7/8 1700.00

1-3/4 12-13/16 8-1/2 9 4-1/2 2-7/8 1-27/32 4-3/8 1775.00

1-7/8-2 15-1/8 10-3/8 12 6 3-1/8 2-3/32 5-7/8 2500.00

2-1/4 17-1/8 11-7/8 14 7 3-5/8 2-3/8 6-7/8 3950.00

2-1/2 17-1/2 13-1/2 15-3/4 8-1/2 4-1/4 2-5/8 8-1/4 5000.00

DIMENSIONS IN INCHES

Stainless Steel HEAVY DUTY

TYPE 304 • ROLLED NOT FORGED

WIRE ROPE WEIGHT

DIA. SIZE per 100 in Inches in Lbs.

1/8 Lt. Duty 2.5

3/16 Lt. Duty 2.5

1/4 8.3

5/16 10.9

3/8 25.1

1/2 49.5

5/8 73

3/4 130

7/8 175

1 275

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Forged Dimensions in inches Weights in pounds

*1/8 only is supplied with reg.

Hex nut and zinc plated U-bolt.

How to attach drop Forged wire rope clips

The right way to attach wire rope clips is illustrated at left. The base of saddle should bear on the live end of the rope- U-bolt on the short or dead end. Staggering or reversing the clips does NOT give additional holding power.

1. ATTACH FIRST CLIP one base width from dead end of rope. Tighten nuts securely.

2. ATTACH SECOND CLIP as close to loop as possible. Tighten nuts firmly but not completely tight.

3. ATTACH ALL OTHER CLIPS (if required) equally spaced between the first two. Tighten nuts firmly.

CAUTION

Apply the initial load to the rope. Alternately and uniformly retighten all nuts securely, to compensate for any reduction of rope diameter. Inspect and periodically retighten. The number of clips shown should be used for 6 v 19 or 6 x 37 class, fiber core or IWRC, IPS or XIPS, right regular or long lay Wire Rope, and 8 x 19 or 8 x 7 class, fibre core, IPS or XIPS, Wire Rope.

For 6 x 19 Seale construction or similar large outer wire constructions, add one extra clip for sizes 1” and larger. Where service conditions are unusually severe, or for other classes of rope not mentioned above, add one additional clip.

Drop Forged Wire Rope Clips, when properly applied to new rope will develop high efficiencies (approximately 80%) based upon the catalog breaking strength of the wire rope. Failure to follow the above instructions will cause a reduction in efficiency.

Please include stock number and size when ordering.

• All clips are supplied with cold-forged double chamfered, heavy hex, UNC-2B nuts. *

• Meet Federal Specification FF-C-450c Type I, Class 1.

• Base, U-bolt and nuts are hot-dip galvanized in accordance with ASTM Specification A-153. *

• Forged wire rope clips are not designed for load carrying purposes therefore, working load limits have not been established.

MIN. NO. Min.

Size for Clips for Spacing Appx. Wt.

HOW TO ROPE Max between per 100

ORDER DIA. A B C D E F G H Strength Clips Pcs.

1/8 1/2 1 7/16 3/4 15/16 7/32 27/32 7/16 2 3/4 6.0

To order 3/16 19/32 1-3/32 5/8 31/32 1-3/16 1/4 15/16 1/2 2 1-1/8 9.0

1/4 11/16 1-7/16 7/8 1-7/32 1-1/2 5/16 1-1/8 11/16 2 1-1/2 18.0 use the 5/16 7/8 1-11/16 1 1-5/8 1-31/32 3/8 1-5/16 3/4 2 1-7/8 30.0

3/8 1 1-15/16 7/8 1-5/8 2 7/16 1-1/2 7/8 2 2-1/4 44.5

Prefix 1/2 1-3/16 2-1/4 1-1/16 1-29/32 2-5/16 1/2 1-13/16 1-3/32 3 3 71.6

5/8 1-1/4 2-3/8 1-7/16 2-3/8 2-7/8 9/16 2-1/16 1-1/4 3 3-3/4 100.0

WRC 3/4 1-1/2 2-3/4 1-1/2 2-13/16 3-3/8 5/8 2-5/16 1-15/32 4 4-1/2 140.0

size 7/8 1-3/4 3-3/16 1-7/8 3-1/8 3-7/8 3/4 2-7/16 1-1/2 4 5-1/4 200.0 follow ed 1 1-7/8 3-1/2 2-1/4 3-1/2 4-1/4 3/4 2-11/16 1-3/4 5 6 245.0

1-1/8 2-1/16 3-11/16 2-3/16 3-7/8 4-5/8 3/4 3 2 6 6-3/4 285.0 by FGD. 1-1/4 2-3/16 4-1/16 2-3/8 4-1/4 5-1/8 7/8 3-1/4 2-5/32 6 7-1/2 415.0

1-1/2 2-19/32 4-1/2 2-7/16 5 5-7/8 7/8 3-3/8 2-13/32 7 9 543.0

DIMENSIONS

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Malleable / Zinc Plated or Self Colored Dimensions in inches/Weights in pounds

• All regular hex nuts.

• Clips meet FF-C-450 Type I Class 2

• Bulk pack

• Wire rope clips are not designed for load carrying purposes therefore, Working Load Limits have not been established.

USE CLIPS PROPERLY FOR MAXIMUM EFFICIENCY

1. U-Bolt should bear on dead end of rope.

2. Recommended number of clips, depending on safety requirement:

3. Spacing between clips should be 6 times the rope diameter.

4. Nuts should be re-tightened after initial load.

Zinc plated will be supplied unless otherwise specified.

SELF-COLORED ZINC-PLATED

RECOMMENDED

SIZE NUMBER OF CLIPS

1/16 to 3/8 2-4 7/16 to 5/8 3-4

3/4 to 1 4-5 1-1/8 to 1-1/4 6-8

HOW TO ROPE APPX. WT.

ORDER SIZE PER 100 PCS.

* 1/16 3.0

* 1/8 4.5 3/16 6.5

To order 1/4 12.0 5/16 12.0 use the 3/8 19.0 7/16 21.8

Prefix: 1/2 37.0 9/16 46.0

WRC-Size 5/8 54.0 3/4 80.0 followed 7/8 116.0 1 137.0 by MAL. 1-1/8 267.0 1-1/4 328.0

HOW TO ROPE APPX. WT.

ORDER SIZE PER 100 PCS.

* 1/16 3.0

To order * 1/8 4.5 3/16 6.5 use the 1/4 12.0 5/16 12.0

Prefix: 3/8 19.0 7/16 21.8

WRC-Size 1/2 37.0 9/16 46.0 followed 5/8 54.0 3/4 80.0 by ZP. 7/8 116.0 example: 1 137.0

WRC-1/2ZP 1-1/8 267.0

1-1/4 328.0

*NOTE: Not covered by FF-C-450 Type 1 Class 2

FA461018R0014

se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

WIRE ROPE WEIGHT

DIA. SIZE EACH

in Inches A B C D E F in Lbs.

1/8 1-15/16 1-1/16 1-5/16 11/16 5/32 5/8 3.3

3/16 1-15/16 1-1/16 1-5/16 11/16 7/32 5/8 3.3

1/4 1-15/16 1-1/16 1-5/16 11/16 9/32 5/8 3.3

5/16 2-1/8 1-1/4 1-1/2 13/16 3/8 3/4 4

3/8 2-3/8 1-15/32 1-5/8 15/16 7/16 7/8 7.50

1/2 2-3/4 1-3/4 1-7/8 1-1/8 9/16 1-1/16 18.80

5/8 3-1/2 2-3/8 2-1/4 1-3/8 11/16 1-1/4 36.

3/4 3-3/4 2-11/16 2-1/2 1-5/8 13/16 1-1/2 60.

7/8 5 3-3/16 3-1/2 1-7/8 15/16 1-3/4 90.

1 5-11/16 3-3/4 4-1/4 2-1/2 1-1/16 2-3/8 105.

1-1/8-1-1/4 6-1/4 4-5/16 4-1/2 2-3/4 1-5/16 2-5/8 166.

1-1/2 7-1/2 5-3/8 5 3-1/4 1-9/16 3-1/8 325.

1-3/4 10-3/4 7-1/4 7-1/4 4-1/4 1-7/8 4-1/8 583.25

2 10-3/4 7-1/4 7-1/4 4-1/4 2-1/8 4-1/8 583.25

DIMENSIONS IN INCHES

Wire Rope Thimbles Stainless Steel

HEAVY DUTY

STANDARD

PER FED. SPEC. FF-T-276B, TYPE III • ALSO AVAILABLE WITH WELDED GUSSET

WELDED GUSSET PLATES AVAILABLE FOR GUSSET 2”, 2 1/4”, AND 2 1/2”

MEETS FEDERAL SPECIFICATIONS FF-T-276B, TYPE II

WIRE ROPE MAX. PIN WEIGHT

DIA. SIZE DIA. per 100 in Inches A B C D E F in Inches in Lbs.

1/4 2-3/16 1-1/2 1-5/8 7/8 13/32 9/32 13/16 6.5

5/16 2-1/2 1-13/16 1-7/8 1-1/16 1/2 11/32 15/16 11.25

3/8 2-7/8 2-1/8 2-1/8 1-1/8 21/32 13/32 1-1/16 25.00

7/16 3-1/4 2-3/8 2-3/8 1-1/4 3/4 15/32 1-3/16 50.00

1/2 3-5/8 2-3/4 2-3/4 1-1/2 27/32 17/32 1-7/16 51.00

9/16 3-5/8 2-11/16 2-3/4 1-1/2 29/32 19/32 1-7/16 51.00

5/8 4-1/4 3-1/8 3-1/4 1-3/4 1 21/32 1-5/8 75.00

3/4 5 3-3/16 3-3/4 2 1-1/4 25/32 1-7/8 147.00

7/8 5-1/2 4-1/4 4-1/4 2-1/4 1-3/8 15/16 2-1/8 175.00

1 6-1/8 4-15/16 4-1/2 2-1/2 1-9/16 1-1/16 2-3/8 275.00

1-1/8-1-1/4 7 5-7/8 5-1/8 2-7/8 1-7/8 1-5/16 2-3/4 400.00

1-1/4-1-3/8 9-1/16 6-13/16 6-1/2 3-1/2 2-1/4 1-7/16 3-1/4 817.00

1-3/8-1-1/2 9 7-1/8 6-1/4 3-1/2 2-5/8 1-9/16 3-3/8 1175.00

1-5/8 11-1/4 8-1/8 8 4 2-3/4 1-23/32 3-7/8 1700.00

1-3/4 12-13/16 8-1/2 9 4-1/2 2-7/8 1-27/32 4-3/8 1775.00

1-7/8-2 15-1/8 10-3/8 12 6 3-1/8 2-3/32 5-7/8 2500.00

2-1/4 17-1/8 11-7/8 14 7 3-5/8 2-3/8 6-7/8 3950.00

2-1/2 17-1/2 13-1/2 15-3/4 8-1/2 4-1/4 2-5/8 8-1/4 5000.00

DIMENSIONS IN INCHES

Stainless Steel HEAVY DUTY

TYPE 304 • ROLLED NOT FORGED

WIRE ROPE WEIGHT

DIA. SIZE per 100 in Inches in Lbs.

1/8 Lt. Duty 2.5

3/16 Lt. Duty 2.5

1/4 8.3

5/16 10.9

3/8 25.1

1/2 49.5

5/8 73

3/4 130

7/8 175

1 275

FA461018R0014

Fused Cutout / Lightning Arrester Specifications se ll W ell s

Type ICX Interchangeable Cutout

15-38 kV Outdoor Distribution Cutout Product Bulletin 1VAG271201-DB

FA461018R0014

se ll W ell s

Product Features

• 15, 27, or 38 kV

• 110, 125, 150, 180, or 200 kV BIL

• 100 A, 200 A Fused

• 300 A Disconnect Blade

• Porcelain, Silicone, or Polymer Concrete Insulators Available

• Seacoast Design

• ECD (Emission Control Device)

• Cutout/Arrester Combo

• Kick-out Spring

Description The ABB ICX interchangeable cutout is used on overhead distribution systems to provide overcurrent protection and visible indication of fuse operation. The ICX provides a visible break sectionalizing point for maintenance personnel and is equipped with hooks to use with a portable loadbreak tool. This allows the ICX to be used as a loadbreak switch to open the circuit with load current flowing.

Silicone or Polymer Concrete insulators, Emission Control Devices (ECDs), Seacoast design, cutout/arrester combinations, and Autolink options are available on certain models.

Ratings The ICX cutout is offered in three frame sizes and five BIL ratings.

Each of the frames accommodates fuseholders with various ratings.

ICX ratings are 110 kV through 200 kV BIL.

Design Features The ICX 100 A fuse is provided with a moisture proof tube as a stan-dard offering. Cutouts perform by expelling gases during interruption from the bottom of the fuse tube. For the highest interrupting rating, a link extender rod is attached to the fuse tube cap, improving the effi-ciency of gas expulsion and arc interruption. Fuse tubes with more than one rating are clearly labeled to indicate each interrupting capability.

This minimizes the number of styles that must be stocked, while pro-viding the broadest range of application flexibility.

Interchangeability The ICX cutout is designed to be electrically and mechanically inter-changeable with the S&C type “XS”, A.B. Chance type “C”, and Cooper type “L” cutouts. Fuseholder caps are also interchangeable with the S&C design. Testing has confirmed the performance of the ICX fuse-holder and fuse support with S&C and Chance.

Standards and Design Testing The ICX cutout meets or exceeds all applicable requirements of EEI, NEMA SG-2-1986, and ANSI C37.41.1994 and C37.42-1989 standards.

- 2 -

ICX with ECD

ICX with arrester combination

15 kV ICX polymer concrete

FA461018R0014

se ll W ell s

Silicone Rubber Silicone rubber has been used for more than 25 years as an outdoor insulation material and has become the fastest growing choice for polymeric material for medium and high voltage outdoor insulation. Silicone was selected for its superior performance, durability, and insulation properties.

It has the unique ability to maintain its hydrophobicity and offers greater stability against heat and ultraviolet radiation compared to other polymers. In addition, silicone cutouts are 30% - 50% lighter than porcelain units. Silicone insula-tors are available in all ratings up to 180 kV BIL.

Polymer Concrete ABB has been using polymer concrete for more than 10 years. It is available in the 110 and 125 kV BIL ratings.

Polymer concrete provides a safe, shatter-proof design with molded-in rods to prevent moisture penetration.