Draft Attachment Steris Steam Generator.pdf

STERIS Corporation • 5960 Heisley Road • Mentor, Ohio 44060

STERIS Corporation Equipment Submittal

TRANSMITTAL

Total number of pages: 1 of 1 October 4, 2021

To: US Dept of Agriculture Address: 800 Buchanan St Albany, CA 94710

Attn: Bindosh Mathan Ph: 512-759-8262 Email: orders@aantilia.com

PO#: 12905B21P0308/ AAN-13021015-NC

STERIS Order #: 13799180

From: Stephanie Kovalcheck

5960 Heisley Rd Mentor, OH 44060

Ph: 440-392-7076

FX: 440-350-7077

Email: Stephanie_Kovalcheck@steris.com

STERIS IS TRANSMITTING:

Date Description Rev.

10/4/2021 Equipment Submittals for Approval. 0

Approval Needed For Reference Only Certified for Construction

Comments:

Important: Seismic installation price includes slab on grade method only. Any other method of seismic installation including but not limited to, “upper floor” or “through bolting” or “elevated slab” method is not included in the STERIS price or current scope of supply. Additional charges will apply if through bolting is required. These charges will be determined after specific site conditions are investigated. See original quote language: “Seismic Anchoring (Excludes x-raying the floor, through bolting, & associated hardware)” mailto:jjessup@sees.com%C2%A0%C2%A0%C2%A0%C2%A0 mailto:jjessup@sees.com%C2%A0%C2%A0%C2%A0%C2%A0 mailto:jjessup@sees.com%C2%A0%C2%A0%C2%A0%C2%A0 mailto:jjessup@sees.com%C2%A0%C2%A0%C2%A0%C2%A0 mailto:Stephanie_Kovalcheck@steris.com

APPROVAL FORM

Date: October 4, 2021

PROJECT: US DEPT OF AGRICULTURE

PO: 12905B21P0308/ AAN-13021015-NC

STERIS ORDER: 13799180

STERIS would like to thank you for your recent order. This equipment package relates to the items specified by your purchase order number referenced above. It is the intent of this package to promote a clear understanding (between all parties) of the space requirements for and mechanical details of the equipment to be furnished by STERIS Corporation.

The enclosed documents describe equipment only as it is routinely manufactured to conform to the standards cited in those documents and statutory requirements prevailing in most communities in which the equipment likely would be installed.

Unless specifically called for in your invitation for bids, request for quotations, contract, or order, the said equipment will not include any different or additional devices or appurtenances that might be required by specific local electrical, plumbing and other statutory requirements.

Key points to consider:

This copy then will be regarded as an integral part of your order or contract.

Fabrication of the equipment shall be in accordance with this signed, approved Equipment Submittal.

Manufacturing of the equipment will not begin until the signed submittal is returned, and all submittal comments are approved by STERIS.

Any and all notations made by you, the Customer, on this signed copy of the submittal will be reviewed by your STERIS Account Manager to determine any adjustments to the original contract price as well as original quoted lead-time. A revised quote and STERIS Change Acknowledgement Form will be submitted to you in order to confirm changes.

Sign and return one (1) copy of this submittal approval page by 10/18/2021 to your STERIS contact:

Stephanie Kovalcheck Supervisor, Life Sciences Customer Operations STERIS Corporation 5960 Heisley Rd.

Mentor, OH 44060 Ph: 440-392-7076

FX: 440-350-7077

Email: Stephanie_Kovalcheck@steris.com

Please check one of the boxes below:

Approved as is Approved as noted

• Resubmittal NOT required

Rejected Approved as noted

• Resubmittal required

Customer Approval Signature: Date:

Required On-Site Equipment Date:

APPROVAL FORM

Date: October 4, 2021

PROJECT: US DEPT OF AGRICULTURE

PO: 12905B21P0308/ AAN-13021015-NC

STERIS ORDER: 13799180

Comments & Clarifications - *Please utilize the below section to detail any comments, questions, or exceptions noted throughout this submittal package.

TAB #_________

ITEM #_________

COMMENT:

EQUIPMENT DETAIL

1 100 KW Electric Steam Generator

CH10861

• 480V

• Carbon Steel

2 Auto Flush & Drain Kit P755718616

1 60 KW Electric Steam Generator

CH07861

• 480V

• Carbon Steel

AMSCO® ELECTRIC STEAM

GENERATORS - CES SERIES

(Typical – details may vary.)

APPLICATION

Amsco Electric Steam Generators (CES Series) provide the high-quality (97%-vapor quality) steam needed to power equipment such as sterilizers, water stills, utensil sanitizers and water temperature boosters for washing equipment. They provide a steam source when in-house supply is not available, when an emergency standby is required, or when a remote location needs to be served.

When a deionized, distilled or reverse osmosis water supply (min. resistivity of 1 megohm/cm) is available, stainless steel generators can also be used to supply pure steam.

CONSTRUCTION

STERIS furnishes all components necessary to obtain a complete working unit, ready for (but not including) installation and connection to the building utility service lines and the equipment to be powered.

Heating Section

The pressure vessel is ASME Grade carbon steel rated for 100 psig. If selected, 316L stainless steel can be supplied for use with deionized, distilled or reverse osmosis water.

STANDARDS

Generator meets the applicable requirements of the following standards:

• American Society of Mechanical Engineers Code, Section I, Part PMB for power boilers and is so stamped

• Underwriters Laboratories Incorporated

• Canadian Standards Association listings

• Seismic pre-approval; meets Zone 4 when installed according to the installation instructions.

FEATURES

Openings are provided for water inlet, drain, steam outlet, gages, instrumentation and immersion type heating elements rated 105 W/in2 brazed into heavy duty ASME flanges. Each e

A s c

Selections Checked Belo lement consists of 80% nickel, 20% chromium resistance wire.

08, 240, or 480 Volt, 50/60 Hz, 3-phase operation as selected.* utomatic controls operate on 120 Volt, 50/60 Hz electric ervice. Operation of the generator is automatic. Standard omponents include:

Flush system - the generator's heating section can be manually flushed. An automatic flushing option is also available. Review local codes before flushing generator.

Water-level control - energizes the water pump and supply valve to ensure proper water level in the drum. This system uses a bronze or stainless steel, positive displacement pump, with drive motor wired for operation on 120 Volt, 50/60 Hz electric service. Motor has automatic overload protection. In addition, it shuts off power to the heaters if water in the heating section should fall below a preset level to protect the heater. A w Apply To This Equipment

GENERATOR RATING (KW)

❏ 30 ❏ 75 ❏ 150

❏ 40 ❏ 100 ❏ 180

❏ 60 ❏ 120

ELECTRICITY *

❏ 208 V, 3 Phase ❏ 240 V, 3 Phase ❏ 480 V, 3 Phase

❏ 380 V, 3 Phase ❏ 415 V, 3 Phase ❏ 575 V, 3 Phase

* Other voltages are available on special order.

C

ONSTRUCTION

316L Stainless Steel Carbon Steel

CH07861

SD56 Rev B (10296435)

Item ________________________

Location(s)___________________ skovalch Highlight skovalch Highlight skovalch Highlight water-level sight gauge with upper and lower hand-valve shutoffs is provided for servicing. Sightglass valves are equipped with ASME rated automatic shutoff if the sight gauge glass should break.

• Steam pressure controls - generators are supplied with operating and high limit pressure controls. One (two for 100-180 kW units) is used for controlling the operating pressure of the generator (0-90 psi adjustable operating range) while the other is used as a high limit pressure control, and incorporates a manual reset which protects the generator from a damaging over pressure condition should one occur.

* Other voltages are available upon special order.

• Electric door interlock - interrupts the 120 V control circuit whenever the generator's main electrical door panel is opened and shuts off the generator for safety.

• Auxiliary low water cut-off - a safety backup protection that turns off the power to the heating element(s) in the event of a low water level control failure.

• High water sensing protection - if an equipment malfunction occurs and the outlet should fill with water, the water sensing system closes the steam outlet, preventing liquid from entering service lines to user devices. The system also activates a visual alarm, with a manual reset alerting operator of a malfunction.

The boiler is fully insulated and equipped with a steel jacket having a baked enamel finish. Plumbing and control devices are copper alloy or stainless steel.

The boiler is equipped with an ON-OFF control switch and pilot light.

If stainless steel construction is selected, all components in contact with feedwater and steam are 316L stainless steel or equal.

PERFORMANCE CAPABILITIES

Electric steam generators can provide the high pressure steam (90 psig max.) required for either single or multiple equipment arrangements. Available models are listed in Engineering Data, next page.

NOTES

1. Pipe sizes shown indicate terminal outlets only. Building service lines, provided by others, must supply the specified pressures and flow rates.

2. STERIS recommends supplying hot water at 140°F (60°C) (maximum 150°F [60°C]) to the generator to minimize heat-up time and conserve electricity; cold water at 70°F (21°C) may be substituted, but only with sacrifice of heat-up time. For proper boiler operation and reasonable element life, STERIS recommends the feed water quality be controlled within the following parameters:

For Stainless Steel Generators: requires deionized, distilled or reverse osmosis water with minimum resistivity of 1 megohm/cm. Do not connect tap water to stainless steel generators. Use of water not meeting the required feedwater quality will invalidate the warranty and is a violation of ASME Boiler Codes.

3. Clearances shown are minimal for installing and servicing the equipment.

4. Disconnect switches (by others) should be installed in electric supply lines as close to the equipment as possible.

Water in and steam out lines should also be equipped with independent shut-off valves.

5. STERIS recommends that steam generating equipment be maintained and operated in an area where temperature does not exceed 90°F (32°C) and 10% to 90% RH non-condensing.

6. Other voltage specifications are available through special order.

* 17.1 mg/L = 1 grain hardness ** WARNING - BURN HAZARD: Sterilizer operator may be severely burned by scalding water if the water level control malfunctions. The steam generator level control may malfunction if the supply water exceeds 26,000 ohms/cm (38.5 micro-mhos conductivity min.). Do not connect to treated water (e.g., distilled, reverse osmosis, deionized) unless water resistivity is determined to be acceptable. If water exceeds 26,000 ohms/cm, contact STERIS Engineering Service for information concerning modifications required to the generator control system.

CUSTOMER IS RESPONSIBLE FOR COMPLIANCE WITH

APPLICABLE LOCAL AND NATIONAL CODES AND

REGULATIONS.

For Carbon Steel Generators

Condition Nominal

Condition Max. Condition

Temperature as supplied 150°F (65°C)

Total Hardness as CaCO3* 0-17 mg/L 17 mg/L

Total Dissolved Sol-ids

50-150 mg/L 250 mg/L

Total Alkalinity as CaCO3

50-100 mg/L 180 mg/L pH 6.8-7.5 8.5

Total Silica 0.1-1.0 mg/L 2.5 mg/L

Resistivity -ohms/cm**

2000-6000 26000

For Carbon Steel Generators

Condition Nominal

Condition Max. Condition

** Minimum wire type - AWG (MCM) 90°C CU (copper) wire only.

ENGINEERING DATA

Rating (kW) 30 40 60 75 100 120 150 180

Developed Boiler Horsepower 3.1 4.1 6.1 7.7 10.4 12.2 15.3 18.4

Generator Steam Output -- lbs/hr (kg/hr) 70°F (21°C) feedwater - 80 psig operating pressure

140°F (60°C) feedwater - 80 psig operating pressure

89.3 (40.6)

(54.1)

178.5 (81.1)

(101.4)

297.5 (135.2)

(162.3)

446.1 (202.8)

535.5 (243.4)

95.2 (43.3)

(57.7)

190.5 (86.6)

238.1 (108.2)

317.5 (144.3)

381.1 (173.2)

476.3 (216.5)

571.5 (259.8)

Gross BTU Output (BTU/hr) 102,360 136,480 204,720 255,900 348,024 409,440 511,800 614,160

Operating Weight lbs/hr (kg/hr) 400 (181)

(186)

(190)

(295)

(425)

(428)

(430)

(434)

Electrical Requirements: Heaters:

208 V - 3-Phase (amp/ph) 84 112 167 209 278 334 417 500

240 V - 3-Phase (amp/ph) 73 97 145 181 241 289 361 434

480 V - 3-Phase (amp/ph) 36 48 72 90 121 144 180 217

380 V - 3-Phase (amp/ph) 46 61 91 114 152 183 228 274

415 V - 3-Phase (amp/ph) 42 56 84 105 140 167 209 251

600 V- 3-Phase (amp/ph) 29 39 58 72 96 116 145 173

Controls & Pump Motor:

120 V - 1Phase

15 15 15 15 15 15 15 15

Fuse Breaker Size:

208 V - 3-Phase (amp/ph) 110 150 225 300 400 450 600 700

240 V - 3-Phase (amp/ph) 100 125 200 250 350 400 500 600

480 V - 3-Phase (amp/ph) 50 60 90 125 150 200 250 300

380 V - 3-Phase (amp/ph) 60 80 125 150 200 250 300 350

415 V - 3-Phase (amp/ph) 60 80 110 150 175 225 300 350

600 V - 3-Phase (amp/ph) 40 50 80 100 125 175 200 250

Input Wire Size**

208 V - 3-Phase 1 2/0 250 or 6-1/0

400 or 6-2/0

500 or 6-3/0

900 or 6-250 6-400 6-500

240 V - 3-Phase 2 1/0 4/0 300 or 6-1/0

500 or 6-3/0

700 or 6-4/0 3-300 6-400

480 V - 3-Phase 6 4 2 1/0 2/0 4/0 300 or 6-1/0

400 or 6-2/0

380 V - 3-Phase 6 4 1/0 2/0 3/0 300 or 6-1/0

400 or 6-2/0

500 or 6-3/0

415 V - 3-Phase 6 4 1 2/0 3/0 250 or 6-1/0

400 or 6-2/0

500 or 6-3/0

600 V - 3-Phase 8 6 4 2 1/0 3/0 4/0 300 or 6-1/0

Water Consumption -- gph (litres per hour) at 70 psig water inlet 140°F (60°C)

(46)

(60)

(95)

(118)

(163)

(194)

(239)

(289)

Heat Loss -- BTU/hr at 70°F (21°C); continuous operation

1750 1750 2600 3500 4400 4800 4800 4800

SD56

UTILITY REQUIREMENTS

Waste (W)

For 30 to 180 kW generators:

1" NPT.

Hot Water (HW)

1/2" NPT; 20 to 50 psig (1.41 to

3.52 kg/cm2, dynamic); 140°F (60°C) recommended - see Note 2.

Steam Outlet (S)

For 30 to 75 kW generators:

3/4" NPT; for 100 to 180 kW Generators: 1" NPT.

Electrical (E1)

30 to 40 kW generators: 208, 240, or 480 Volt, 3-Phase, 50/60 Hz.

Electrical (E2)

60 to 180 kW generators: 208, 240, or 480 Volt, 3-Phase, 50/60 Hz.

Electrical (E3)

120 Volt, 15 Amp, 1-Phase 50/60 Hz service for control and pump motor.

A Overall Height

B Overall Length

C Overall Width

D Cabinet Height

E Cabinet Length

F Cabinet Width

G Service

Cl nce

4 36 24- / 15

11 mm 7 mm mm 914mm 61 mm 38 mm mm

64 51 27-1/4 18 3

1625mm

8 m

3 - /4 mm 1295mm 692mm 4 mm mm

DIMENSIONS - inches (mm) Generator Size (kW)

30 to 75 kW

100-180 kW

* Service Clearance ** Pump Location - 10 to 20 kW Units *** Pump Location - 30 to 80 kW Units

1" (25mm)

18" * (457mm)

18" * (457mm)

18" * (457mm)

18" * (457mm)

F

B

E

S

1-3/4" (45mm)

1-3/16" (30mm)

Bracket: 0.119" (11GA.) A1008 CRS Anchor Hole: 7/16"

C

D

G

E2 HW

E2

S

E3

E1

W

FRONT VIEW SIDE VIEW REAR VIEW

A

HW

W

For further information, contact:

STERIS Corporation 5960 Heisley Road Mentor, OH 44060-1834 • USA 440-354-2600 • 800-548-4873 www.steris.com

This document is intended for the exclusive use of STERIS Customers, including architects or designers. Reproduction in whole or in part by any party other than a Customer is prohibited. ©2018, STERIS Corporation. All rights reserved. (Rev B. (10269435)

NOTE: Because of STERIS’s continuing program of research and development, all specifications and descriptions are subject to change without notice. Some options my affect utility consumptions. Obtain approved drawings for design and installation.

AMSCO® ELECTRIC STEAM

GENERATORS - CES SERIES

(Typical – details may vary.)

APPLICATION

Amsco Electric Steam Generators (CES Series) provide the high-quality (97%-vapor quality) steam needed to power equipment such as sterilizers, water stills, utensil sanitizers and water temperature boosters for washing equipment. They provide a steam source when in-house supply is not available, when an emergency standby is required, or when a remote location needs to be served.

When a deionized, distilled or reverse osmosis water supply (min. resistivity of 1 megohm/cm) is available, stainless steel generators can also be used to supply pure steam.

CONSTRUCTION

STERIS furnishes all components necessary to obtain a complete working unit, ready for (but not including) installation and connection to the building utility service lines and the equipment to be powered.

Heating Section

The pressure vessel is ASME Grade carbon steel rated for 100 psig. If selected, 316L stainless steel can be supplied for use with deionized, distilled or reverse osmosis water.

STANDARDS

Generator meets the applicable requirements of the following standards:

• American Society of Mechanical Engineers Code, Section I, Part PMB for power boilers and is so stamped

• Underwriters Laboratories Incorporated

• Canadian Standards Association listings

• Seismic pre-approval; meets Zone 4 when installed according to the installation instructions.

FEATURES

Openings are provided for water inlet, drain, steam outlet, gages, instrumentation and immersion type heating elements rated 105 W/in2 brazed into heavy duty ASME flanges. Each e

A s c

Selections Checked Belo lement consists of 80% nickel, 20% chromium resistance wire.

08, 240, or 480 Volt, 50/60 Hz, 3-phase operation as selected.* utomatic controls operate on 120 Volt, 50/60 Hz electric ervice. Operation of the generator is automatic. Standard omponents include:

Flush system - the generator's heating section can be manually flushed. An automatic flushing option is also available. Review local codes before flushing generator.

Water-level control - energizes the water pump and supply valve to ensure proper water level in the drum. This system uses a bronze or stainless steel, positive displacement pump, with drive motor wired for operation on 120 Volt, 50/60 Hz electric service. Motor has automatic overload protection. In addition, it shuts off power to the heaters if water in the heating section should fall below a preset level to protect the heater. A w Apply To This Equipment

GENERATOR RATING (KW)

❏ 30 ❏ 75 ❏ 150

❏ 40 ❏ 100 ❏ 180

❏ 60 ❏ 120

ELECTRICITY *

❏ 208 V, 3 Phase ❏ 240 V, 3 Phase ❏ 480 V, 3 Phase

❏ 380 V, 3 Phase ❏ 415 V, 3 Phase ❏ 575 V, 3 Phase

* Other voltages are available on special order.

C

ONSTRUCTION

316L Stainless Steel Carbon Steel SD56 Rev B (10296435)

Item __CH10861______________ Location(s)___________________ skovalch Highlight skovalch Highlight skovalch Highlight water-level sight gauge with upper and lower hand-valve shutoffs is provided for servicing. Sightglass valves are equipped with ASME rated automatic shutoff if the sight gauge glass should break.

• Steam pressure controls - generators are supplied with operating and high limit pressure controls. One (two for 100-180 kW units) is used for controlling the operating pressure of the generator (0-90 psi adjustable operating range) while the other is used as a high limit pressure control, and incorporates a manual reset which protects the generator from a damaging over pressure condition should one occur.

* Other voltages are available upon special order.

• Electric door interlock - interrupts the 120 V control circuit whenever the generator's main electrical door panel is opened and shuts off the generator for safety.

• Auxiliary low water cut-off - a safety backup protection that turns off the power to the heating element(s) in the event of a low water level control failure.

• High water sensing protection - if an equipment malfunction occurs and the outlet should fill with water, the water sensing system closes the steam outlet, preventing liquid from entering service lines to user devices. The system also activates a visual alarm, with a manual reset alerting operator of a malfunction.

The boiler is fully insulated and equipped with a steel jacket having a baked enamel finish. Plumbing and control devices are copper alloy or stainless steel.

The boiler is equipped with an ON-OFF control switch and pilot light.

If stainless steel construction is selected, all components in contact with feedwater and steam are 316L stainless steel or equal.

PERFORMANCE CAPABILITIES

Electric steam generators can provide the high pressure steam (90 psig max.) required for either single or multiple equipment arrangements. Available models are listed in Engineering Data, next page.

NOTES

1. Pipe sizes shown indicate terminal outlets only. Building service lines, provided by others, must supply the specified pressures and flow rates.

2. STERIS recommends supplying hot water at 140°F (60°C) (maximum 150°F [60°C]) to the generator to minimize heat-up time and conserve electricity; cold water at 70°F (21°C) may be substituted, but only with sacrifice of heat-up time. For proper boiler operation and reasonable element life, STERIS recommends the feed water quality be controlled within the following parameters:

For Stainless Steel Generators: requires deionized, distilled or reverse osmosis water with minimum resistivity of 1 megohm/cm. Do not connect tap water to stainless steel generators. Use of water not meeting the required feedwater quality will invalidate the warranty and is a violation of ASME Boiler Codes.

3. Clearances shown are minimal for installing and servicing the equipment.

4. Disconnect switches (by others) should be installed in electric supply lines as close to the equipment as possible.

Water in and steam out lines should also be equipped with independent shut-off valves.

5. STERIS recommends that steam generating equipment be maintained and operated in an area where temperature does not exceed 90°F (32°C) and 10% to 90% RH non-condensing.

6. Other voltage specifications are available through special order.

* 17.1 mg/L = 1 grain hardness ** WARNING - BURN HAZARD: Sterilizer operator may be severely burned by scalding water if the water level control malfunctions. The steam generator level control may malfunction if the supply water exceeds 26,000 ohms/cm (38.5 micro-mhos conductivity min.). Do not connect to treated water (e.g., distilled, reverse osmosis, deionized) unless water resistivity is determined to be acceptable. If water exceeds 26,000 ohms/cm, contact STERIS Engineering Service for information concerning modifications required to the generator control system.

CUSTOMER IS RESPONSIBLE FOR COMPLIANCE WITH

APPLICABLE LOCAL AND NATIONAL CODES AND

REGULATIONS.

For Carbon Steel Generators

Condition Nominal

Condition Max. Condition

Temperature as supplied 150°F (65°C)

Total Hardness as CaCO3* 0-17 mg/L 17 mg/L

Total Dissolved Sol-ids

50-150 mg/L 250 mg/L

Total Alkalinity as CaCO3

50-100 mg/L 180 mg/L pH 6.8-7.5 8.5

Total Silica 0.1-1.0 mg/L 2.5 mg/L

Resistivity -ohms/cm**

2000-6000 26000

For Carbon Steel Generators

Condition Nominal

Condition Max. Condition

** Minimum wire type - AWG (MCM) 90°C CU (copper) wire only.

ENGINEERING DATA

Rating (kW) 30 40 60 75 100 120 150 180

Developed Boiler Horsepower 3.1 4.1 6.1 7.7 10.4 12.2 15.3 18.4

Generator Steam Output -- lbs/hr (kg/hr) 70°F (21°C) feedwater - 80 psig operating pressure

140°F (60°C) feedwater - 80 psig operating pressure

89.3 (40.6)

(54.1)

178.5 (81.1)

(101.4)

297.5 (135.2)

(162.3)

446.1 (202.8)

535.5 (243.4)

95.2 (43.3)

(57.7)

190.5 (86.6)

238.1 (108.2)

317.5 (144.3)

381.1 (173.2)

476.3 (216.5)

571.5 (259.8)

Gross BTU Output (BTU/hr) 102,360 136,480 204,720 255,900 348,024 409,440 511,800 614,160

Operating Weight lbs/hr (kg/hr) 400 (181)

(186)

(190)

(295)

(425)

(428)

(430)

(434)

Electrical Requirements: Heaters:

208 V - 3-Phase (amp/ph) 84 112 167 209 278 334 417 500

240 V - 3-Phase (amp/ph) 73 97 145 181 241 289 361 434

480 V - 3-Phase (amp/ph) 36 48 72 90 121 144 180 217

380 V - 3-Phase (amp/ph) 46 61 91 114 152 183 228 274

415 V - 3-Phase (amp/ph) 42 56 84 105 140 167 209 251

600 V- 3-Phase (amp/ph) 29 39 58 72 96 116 145 173

Controls & Pump Motor:

120 V - 1Phase

15 15 15 15 15 15 15 15

Fuse Breaker Size:

208 V - 3-Phase (amp/ph) 110 150 225 300 400 450 600 700

240 V - 3-Phase (amp/ph) 100 125 200 250 350 400 500 600

480 V - 3-Phase (amp/ph) 50 60 90 125 150 200 250 300

380 V - 3-Phase (amp/ph) 60 80 125 150 200 250 300 350

415 V - 3-Phase (amp/ph) 60 80 110 150 175 225 300 350

600 V - 3-Phase (amp/ph) 40 50 80 100 125 175 200 250

Input Wire Size**

208 V - 3-Phase 1 2/0 250 or 6-1/0

400 or 6-2/0

500 or 6-3/0

900 or 6-250 6-400 6-500

240 V - 3-Phase 2 1/0 4/0 300 or 6-1/0

500 or 6-3/0

700 or 6-4/0 3-300 6-400

480 V - 3-Phase 6 4 2 1/0 2/0 4/0 300 or 6-1/0

400 or 6-2/0

380 V - 3-Phase 6 4 1/0 2/0 3/0 300 or 6-1/0

400 or 6-2/0

500 or 6-3/0

415 V - 3-Phase 6 4 1 2/0 3/0 250 or 6-1/0

400 or 6-2/0

500 or 6-3/0

600 V - 3-Phase 8 6 4 2 1/0 3/0 4/0 300 or 6-1/0

Water Consumption -- gph (litres per hour) at 70 psig water inlet 140°F (60°C)

(46)

(60)

(95)

(118)

(163)

(194)

(239)

(289)

Heat Loss -- BTU/hr at 70°F (21°C); continuous operation

1750 1750 2600 3500 4400 4800 4800 4800

SD56

UTILITY REQUIREMENTS

Waste (W)

For 30 to 180 kW generators:

1" NPT.

Hot Water (HW)

1/2" NPT; 20 to 50 psig (1.41 to

3.52 kg/cm2, dynamic); 140°F (60°C) recommended - see Note 2.

Steam Outlet (S)

For 30 to 75 kW generators:

3/4" NPT; for 100 to 180 kW Generators: 1" NPT.

Electrical (E1)

30 to 40 kW generators: 208, 240, or 480 Volt, 3-Phase, 50/60 Hz.

Electrical (E2)

60 to 180 kW generators: 208, 240, or 480 Volt, 3-Phase, 50/60 Hz.

Electrical (E3)

120 Volt, 15 Amp, 1-Phase 50/60 Hz service for control and pump motor.

A Overall Height

B Overall Length

C Overall Width

D Cabinet Height

E Cabinet Length

F Cabinet Width

G Service

Cl nce

4 36 24- / 15

11 mm 7 mm mm 914mm 61 mm 38 mm mm

64 51 27-1/4 18 3

1625mm

8 m

3 - /4 mm 1295mm 692mm 4 mm mm

DIMENSIONS - inches (mm) Generator Size (kW)

30 to 75 kW

100-180 kW

* Service Clearance ** Pump Location - 10 to 20 kW Units *** Pump Location - 30 to 80 kW Units

1" (25mm)

18" * (457mm)

18" * (457mm)

18" * (457mm)

18" * (457mm)

F

B

E

S

1-3/4" (45mm)

1-3/16" (30mm)

Bracket: 0.119" (11GA.) A1008 CRS Anchor Hole: 7/16"

C

D

G

E2 HW

E2

S

E3

E1

W

FRONT VIEW SIDE VIEW REAR VIEW

A

HW

W

For further information, contact:

STERIS Corporation 5960 Heisley Road Mentor, OH 44060-1834 • USA 440-354-2600 • 800-548-4873 www.steris.com

This document is intended for the exclusive use of STERIS Customers, including architects or designers. Reproduction in whole or in part by any party other than a Customer is prohibited. ©2018, STERIS Corporation. All rights reserved. (Rev B. (10269435)

NOTE: Because of STERIS’s continuing program of research and development, all specifications and descriptions are subject to change without notice. Some options my affect utility consumptions. Obtain approved drawings for design and installation.

PREPARATION FOR

SHIPMENT

Each unit of equipment shall be placed in a substantial shipping container or crate complying with applicable rules of the I.C.C. Uniform Freight Classifica-tion to ensure acceptance by the common or other carrier for safe transportation to final destination at the lowest rate. The shipping crate or container for heavy equipment (such as sterilizers and water stills) shall be of skid construction to facilitate handling by lift equipment.

The exterior of each container shall be clearly and legibly marked with the room, floor and item number (if available), shipping address, and brief description of the contents. A packing list and complete instructions for uncrating the equipment and setting it in place shall be fastened to the outside of the container or crate; such information shall be protected by a waterproof envelope. Packaging, packing, and marking differing from that above shall be provided, if specified.

STERIS SHIPPING INSTRUCTIONS AND

SERVICE REQUIREMENTS

INSTALLATION

INSTRUCTIONS

Unless additional copies are specified, one set of complete installation instructions, including prints showing all utility service requirements, space requirements and wiring diagrams (if not affixed to the equipment) shall be furnished with each unit of equipment.

OPERATING AND

MAINTENANCE

INSTRUCTIONS

Instructions for operating and perform-ing periodic preventive maintenance on each unit of equipment, including a list of the service parts and quantity of each required for this purpose, shall be furnished. Unless otherwise specified, one copy of this material shall be furnished.

SERVICE AFTER

INSTALLATION*

After installation of each assembly, STERIS shall provide a factory-trained technician to perform repair service as required by the customer. This service shall be on a time and material basis unless the equipment is still within the manufacturer's warranty.

If specified, STERIS shall provide a factory-trained technician to perform preventive maintenance services on each assembly following its test and demonstration.

* These services are available from the STERIS Corporation within the continental United States, Alaska, and Hawaii.

NOTICE: As used in this specification, the terms "if specified", "is specified", "as specified", "when specified", and "unless otherwise specified" are understood to mean that the article, type of article, arrangement, component, material or finish to which any of these terms may relate in the specification will be neither quoted nor furnished by the STERIS Corporation except at the customer's option as stated by him on invitations for bids, requests for price quotations, requests for proposals, contracts, purchase orders or sales orders. STERIS assumes no obligation to supply any of the said affected types, articles, arrangements, components, finishes or materials solely because they are described in this publication.

For further information, please contact:

STERIS Corporation 5960 Heisley Road Mentor, OH 44060-1834 • USA 440-354-2600 • 800-548-4873 In Canada, 800-661-3937 www.steris.com

SD-153R4 ©1998, STERIS Corporation All rights reserved. MC (8/7/98) This data is intended for the exclusive use of STERIS customers, including architects or designers. Reproduction in whole or in part by any party other than a customer is prohibited.

/ASCII85EncodePages false /AllowTransparency false /AutoPositionEPSFiles true /AutoRotatePages /All /Binding /Left /CalGrayProfile (Gray Gamma 2.2) /CalRGBProfile (sRGB IEC61966-2.1) /CalCMYKProfile (U.S. Web Coated \050SWOP\051 v2) /sRGBProfile (sRGB IEC61966-2.1) /CannotEmbedFontPolicy /Warning /CompatibilityLevel 1.5 /CompressObjects /All /CompressPages true /ConvertImagesToIndexed true /PassThroughJPEGImages true /CreateJobTicket false /DefaultRenderingIntent /Default /DetectBlends true /DetectCurves 0.1000 /ColorConversionStrategy /sRGB /DoThumbnails false /EmbedAllFonts true /EmbedOpenType false /ParseICCProfilesInComments true /EmbedJobOptions true /DSCReportingLevel 0 /EmitDSCWarnings false /EndPage -1 /ImageMemory 1048576 /LockDistillerParams false /MaxSubsetPct 100 /Optimize true

/OPM 1

/ParseDSCComments true /ParseDSCCommentsForDocInfo true /PreserveCopyPage true /PreserveDICMYKValues true /PreserveEPSInfo false /PreserveFlatness true /PreserveHalftoneInfo false /PreserveOPIComments false /PreserveOverprintSettings true /StartPage 1 /SubsetFonts true /TransferFunctionInfo /Preserve /UCRandBGInfo /Remove /UsePrologue false /ColorSettingsFile () /AlwaysEmbed [ true /AcadEref /ACaslonPro-Bold /ACaslonPro-BoldItalic /ACaslonPro-Italic /ACaslonPro-Regular /ACaslonPro-Semibold /ACaslonPro-SemiboldItalic /AdobeArabic-Bold /AdobeArabic-BoldItalic /AdobeArabic-Italic /AdobeArabic-Regular /AdobeFangsongStd-Regular /AdobeFanHeitiStd-Bold /AdobeGothicStd-Bold /AdobeHebrew-Bold /AdobeHebrew-BoldItalic /AdobeHebrew-Italic /AdobeHebrew-Regular /AdobeHeitiStd-Regular /AdobeKaitiStd-Regular /AdobeMingStd-Light /AdobeMyungjoStd-Medium /AdobeSongStd-Light /AGaramondPro-Bold /AGaramondPro-BoldItalic /AGaramondPro-Italic /AGaramondPro-Regular /AgencyFB-Bold /AgencyFB-Reg /Aharoni-Bold

/AIGDT

/Algerian /AmdtSymbols /AmericanTypewriter-Bold /AmericanTypewriter-BoldA /AmericanTypewriter-BoldCond /AmericanTypewriter-BoldCondA /AmericanTypewriter-Cond /AmericanTypewriter-CondA /AmericanTypewriter-Light /AmericanTypewriter-LightA /AmericanTypewriter-LightCond /AmericanTypewriter-LightCondA /AmericanTypewriter-Medium /AmericanTypewriter-MediumA

/AMGDT

/Andalus /AngsanaNew /AngsanaNew-Bold /AngsanaNew-BoldItalic /AngsanaNew-Italic /AngsanaUPC /AngsanaUPC-Bold /AngsanaUPC-BoldItalic /AngsanaUPC-Italic /Aparajita /Aparajita-Bold /Aparajita-BoldItalic /Aparajita-Italic /ArabicTypesetting /Arial-Black /Arial-BoldItalicMT /Arial-BoldMT /Arial-ItalicMT /ArialMT /ArialNarrow /ArialNarrow-Bold /ArialNarrow-BoldItalic /ArialNarrow-Italic /ArialRoundedMTBold /ArialUnicodeMS /BankGothicBT-Light /BankGothicBT-Medium /BarCodeDisplay /Batang /BatangChe /Bauhaus93 /BellMT /BellMTBold /BellMTItalic /BirchStd /BlackadderITC-Regular /BlackoakStd /BodoniMTPosterCompressed /BookmanOldStyle /BookmanOldStyle-Bold /BookmanOldStyle-BoldItalic /BookmanOldStyle-Italic /BookshelfSymbolSeven /BrowalliaNew /BrowalliaNew-Bold /BrowalliaNew-BoldItalic /BrowalliaNew-Italic /BrowalliaUPC /BrowalliaUPC-Bold /BrowalliaUPC-BoldItalic /BrowalliaUPC-Italic /BrushScriptStd /Calibri /Calibri-Bold /Calibri-BoldItalic /Calibri-Italic /Calibri-Light /Calibri-LightItalic /Caresymbols /Castellar /CenturySchoolbook /CenturySchoolbook-Bold /CenturySchoolbook-BoldItalic /CenturySchoolbook-Italic /ChaparralPro-Bold /ChaparralPro-BoldIt /ChaparralPro-Italic /ChaparralPro-Regular /CharlemagneStd-Bold /Chiller-Regular /ChollaSansBold /CityBlueprint /ComicSansMS /ComicSansMS-Bold /CommercialPiBT-Regular /CommercialScriptBT-Regular /Complex /Consolas /Consolas-Bold /Consolas-BoldItalic /Consolas-Italic /Constantia /Constantia-Bold /Constantia-BoldItalic /Constantia-Italic /CooperBlackStd /CooperBlackStd-Italic /CordiaNew /CordiaNew-Bold /CordiaNew-BoldItalic /CordiaNew-Italic /CordiaUPC /CordiaUPC-Bold /CordiaUPC-BoldItalic /CordiaUPC-Italic /CountryBlueprint /Courier /CourierNewPS-BoldItalicMT /CourierNewPS-BoldMT /CourierNewPS-ItalicMT /CourierNewPSMT /CurlzMT /DaunPenh /David /David-Bold /DFHei-Bd-HK-BF /DFHei-Bd-HKP-BF /DFHei-W3-WINP-BF /DFHei-W5-WINP-BF /DFHei-W7-WINP-BF /DFKaiShu-SB-Estd-BF /DFKGothic-Bd-WIN-KSC-H /DFKGothic-Md-WIN-KSC-H /DilleniaUPC /DilleniaUPCBold /DilleniaUPCBoldItalic /DilleniaUPCItalic /DokChampa /Dotum /DotumChe /Dutch801BT-Bold /Dutch801BT-BoldItalic /Dutch801BT-ExtraBold /Dutch801BT-Italic /Dutch801BT-Roman /Ebrima /Ebrima-Bold /EPSymbols /ErasITC-Demi /ErasITC-Medium /EstrangeloEdessa /EucrosiaUPC /EucrosiaUPCBold /EucrosiaUPCBoldItalic /EucrosiaUPCItalic /EuphemiaCAS /EuroRoman /EuroRomanOblique /EuroSig /FangSong /Frame5Font /FranklinGothic-Demi /FranklinGothic-DemiItalic /FranklinGothic-Heavy /FranklinGothic-HeavyItalic /FranklinGothic-Medium /FranklinGothic-MediumCond /FranklinGothic-MediumItalic /FrankRuehl /FreesiaUPC /FreesiaUPCBold /FreesiaUPCBoldItalic /FreesiaUPCItalic /FrenchScriptMT /Gabriola /Gadugi /Gadugi-Bold /Gautami /Gautami-Bold

/GDT

/GENISO

/Georgia /Georgia-Bold /Georgia-BoldItalic /Georgia-Italic /GiddyupStd /GillSansMT-Condensed /Gisha /Gisha-Bold /GothicE /GothicG /GothicI /GoudyOldStyleT-Bold /GoudyOldStyleT-Italic /GoudyOldStyleT-Regular /GreekC /GreekS /Gulim /GulimChe /Gungsuh /GungsuhChe /Helvetica /Helvetica-Black /Helvetica-BlackOblique /Helvetica-Bold /Helvetica-BoldOblique /Helvetica-Condensed /Helvetica-Condensed-Black /Helvetica-Condensed-BlackObl /Helvetica-Condensed-Bold /Helvetica-Condensed-BoldObl /Helvetica-Condensed-Light /Helvetica-Condensed-LightObl /Helvetica-Condensed-Oblique /Helvetica-Fraction /Helvetica-FractionBold /Helvetica-Light /Helvetica-LightOblique /HelveticaNeue-BoldItalic /HelveticaNeue-BoldOutline /HelveticaNeueLTCom-Bd /HelveticaNeueLTCom-Cn /HelveticaNeueLTCom-Md /HelveticaNeueLTCom-MdCn /HelveticaNeueLTW1G-Bd /HelveticaNeueLTW1G-BdCn /HelveticaNeueLTW1G-BdCnO /HelveticaNeueLTW1G-BdIt /HelveticaNeueLTW1G-Blk /HelveticaNeueLTW1G-BlkCn /HelveticaNeueLTW1G-BlkCnO /HelveticaNeueLTW1G-BlkIt /HelveticaNeueLTW1G-Cn /HelveticaNeueLTW1G-CnO /HelveticaNeueLTW1G-It /HelveticaNeueLTW1G-Lt /HelveticaNeueLTW1G-LtCn /HelveticaNeueLTW1G-LtCnO /HelveticaNeueLTW1G-LtIt /HelveticaNeueLTW1G-Md /HelveticaNeueLTW1G-MdIt /Helvetica-Oblique /HoboStd /Impact /InformalRoman-Regular /IrisUPC /IrisUPCBold /IrisUPCBoldItalic /IrisUPCItalic /IskoolaPota /IskoolaPota-Bold

/ISOCP

/ISOCP2

/ISOCP3

/ISOCPEUR

/ISOCPEURItalic

/ISOCT

/ISOCT2

/ISOCT3

/ISOCTEUR

/ISOCTEURItalic /Italic /ItalicC /ItalicT /ItcEras-Bold /ItcEras-Book /ItcEras-Demi /ItcEras-Light /ItcEras-Medium /ItcEras-Ultra /JasmineUPC /JasmineUPCBold /JasmineUPCBoldItalic /JasmineUPCItalic /Jokerman-Regular /JuiceITC-Regular /KaiTi /Kalinga /Kalinga-Bold /Kartika /Kartika-Bold /KhmerUI /KhmerUI-Bold /KodchiangUPC /KodchiangUPCBold /KodchiangUPCBoldItalic /KodchiangUPCItalic /Kokila /Kokila-Bold /Kokila-BoldItalic /Kokila-Italic /KozGoPr6N-Bold /KozGoPr6N-ExtraLight /KozGoPr6N-Heavy /KozGoPr6N-Light /KozGoPr6N-Medium /KozGoPr6N-Regular /KozGoPro-Bold /KozGoPro-ExtraLight /KozGoPro-Heavy /KozGoPro-Light /KozGoPro-Medium /KozGoPro-Regular /KozMinPr6N-Bold /KozMinPr6N-ExtraLight /KozMinPr6N-Heavy /KozMinPr6N-Light /KozMinPr6N-Medium /KozMinPr6N-Regular /KozMinPro-Bold /KozMinPro-ExtraLight /KozMinPro-Heavy /KozMinPro-Light /KozMinPro-Medium /KozMinPro-Regular /KristenITC-Regular /LaoUI /LaoUI-Bold /Latha /Latha-Bold /Leelawadee /LeelawadeeBold /Leelawadee-Bold /LetterGothicStd /LetterGothicStd-Bold /LetterGothicStd-BoldSlanted /LetterGothicStd-Slanted /LevenimMT /LevenimMT-Bold /LiHeiPro /LilyUPC /LilyUPCBold /LilyUPCBoldItalic /LilyUPCItalic /LithosPro-Black /LithosPro-Regular /LucidaBright /LucidaBright-Demi /LucidaBright-DemiItalic /LucidaBright-Italic /LucidaCalligraphy-Italic /LucidaConsole /LucidaSans-Typewriter /LucidaSans-TypewriterBold /LucidaSans-TypewriterBoldOblique /LucidaSans-TypewriterOblique /LucidaSansUnicode /Magneto-Bold /MalgunGothic /MalgunGothicBold /MalgunGothicRegular /Mangal /Mangal-Bold /MapInfoCartographic /Map-Symbols /Marlett /Meiryo /Meiryo-Bold /Meiryo-BoldItalic /Meiryo-Italic /MeiryoUI /MeiryoUI-Bold /MeiryoUI-BoldItalic /MeiryoUI-Italic /MesquiteStd /MicrosoftHimalaya /MicrosoftJhengHeiBold /MicrosoftJhengHeiRegular /MicrosoftJhengHeiUIBold /MicrosoftJhengHeiUIRegular /MicrosoftNewTaiLue /MicrosoftNewTaiLue-Bold /MicrosoftPhagsPa /MicrosoftPhagsPa-Bold /MicrosoftSansSerif /MicrosoftTaiLe /MicrosoftTaiLe-Bold /MicrosoftUighur /MicrosoftUighur-Bold /MicrosoftYaHei /MicrosoftYaHei-Bold /MicrosoftYaHeiUI /MicrosoftYaHeiUI-Bold /Microsoft-Yi-Baiti /MingLiU /MingLiU-ExtB /Ming-Lt-HKSCS-ExtB /Ming-Lt-HKSCS-UNI-H /MinionPro-Bold /MinionPro-BoldCn /MinionPro-BoldCnIt /MinionPro-BoldIt /MinionPro-It /MinionPro-Medium /MinionPro-MediumIt /MinionPro-Regular /MinionPro-Semibold /MinionPro-SemiboldIt /Miriam /MiriamFixed /MongolianBaiti /Monospace821BT-Bold /Monospace821BT-BoldItalic /Monospace821BT-Italic /Monospace821BT-Roman /Monotxt /MoolBoran /MS-Gothic /MS-Mincho /MSOutlook /MS-PGothic /MS-PMincho /MSReferenceSansSerif /MSReferenceSpecialty /MS-UIGothic /MT-Extra /MVBoli /MyriadPro-Bold /MyriadPro-BoldCond /MyriadPro-BoldCondIt /MyriadPro-BoldIt /MyriadPro-Cond /MyriadPro-CondIt /MyriadPro-It /MyriadPro-LightCond /MyriadPro-Regular /MyriadPro-Semibold /MyriadPro-SemiboldIt /Narkisim /NiagaraSolid-Reg /NirmalaUI /NirmalaUI-Bold /NSimSun /NuevaStd-BoldCond /NuevaStd-BoldCondItalic /NuevaStd-Cond /NuevaStd-CondItalic /Nyala-Regular /OCRAExtended /OCRAStd

/OCRB

/OCRB-Alternate /OldEnglishTextMT /OratorStd /OratorStd-Slanted /Palatino-Black /Palatino-BlackItalic /Palatino-Bold /Palatino-BoldItalic /Palatino-BoldItalicOsF /Palatino-BoldOsF /Palatino-Italic /Palatino-ItalicOsF /Palatino-Light /Palatino-LightItalic /PalatinoLinotype-Bold /PalatinoLinotype-BoldItalic /PalatinoLinotype-Italic /PalatinoLinotype-Roman /Palatino-Medium /Palatino-MediumItalic /Palatino-Roman /Palatino-SC /PanRoman /PerpetuaTitlingMT-Bold /PerpetuaTitlingMT-Light /PlantagenetCherokee /Playbill /PMingLiU /PMingLiU-ExtB /PoplarStd /PrestigeEliteStd-Bd /Proxy1 /Proxy2 /Proxy3 /Proxy4 /Proxy5 /Proxy6 /Proxy7 /Proxy8 /Proxy9 /PviewSYm /Raavi /Rockwell-Condensed /Rockwell-CondensedBold /Rod /RomanC /RomanD /RomanS /RomanT /Romantic /RomanticBold /RomanticItalic /RosewoodStd-Regular /SakkalMajalla /SakkalMajallaBold /SansSerif /SansSerifBold /SansSerifBoldOblique /SansSerifOblique /ScriptC /ScriptS /SegoePrint /SegoePrint-Bold /SegoeScript /SegoeScript-Bold /SegoeUI /SegoeUI-Bold /SegoeUI-BoldItalic /SegoeUI-Italic /SegoeUI-Light /SegoeUI-SemiBold /SegoeUI-Semilight /SegoeUISymbol /ShonarBangla /ShonarBangla-Bold /Shruti /Shruti-Bold /SimHei /Simplex /SimplifiedArabic /SimplifiedArabic-Bold /SimplifiedArabicFixed /SimSun /SimSun-ExtB /SnapITC-Regular /StencilStd /StylusBT /SuperFrench /Swiss721BT-Black /Swiss721BT-BlackCondensed /Swiss721BT-BlackCondensedItalic /Swiss721BT-BlackExtended /Swiss721BT-BlackItalic /Swiss721BT-BlackOutline /Swiss721BT-Bold /Swiss721BT-BoldCondensed /Swiss721BT-BoldCondensedItalic /Swiss721BT-BoldCondensedOutline /Swiss721BT-BoldExtended /Swiss721BT-BoldItalic /Swiss721BT-BoldOutline /Swiss721BT-Italic /Swiss721BT-ItalicCondensed /Swiss721BT-Light /Swiss721BT-LightCondensed /Swiss721BT-LightCondensedItalic /Swiss721BT-LightExtended /Swiss721BT-LightItalic /Swiss721BT-Roman /Swiss721BT-RomanCondensed /Swiss721BT-RomanExtended /Syastro /Sylfaen /Symap /Symath /SymbolMT /Symeteo /Symusic /Tahoma /Tahoma-Bold /Technic /TechnicBold /TechnicLite /TektonPro-Bold /TektonPro-BoldCond /TektonPro-BoldExt /TektonPro-BoldObl /TimesNewRomanPS-BoldItalicMT /TimesNewRomanPS-BoldMT /TimesNewRomanPS-ItalicMT /TimesNewRomanPSMT /Times-Roman /TraditionalArabic /TraditionalArabic-Bold /TrajanPro-Bold /TrajanPro-Regular /Trebuchet-BoldItalic /TrebuchetMS /TrebuchetMS-Bold /TrebuchetMS-Italic /Tunga /Tunga-Bold /TwCenMT-Bold /TwCenMT-BoldItalic /TwCenMT-Condensed /Txt /UniversalMath1BT-Regular /Utsaah /Utsaah-Bold /Utsaah-BoldItalic /Utsaah-Italic /Vani /Vani-Bold /Verdana /Verdana-Bold /Verdana-BoldItalic /Verdana-Italic /Vijaya /Vijaya-Bold /VinerHandITC /VinetaBT-Regular /Vivaldii /VNI-Internet-Mail /Vrinda /Vrinda-Bold /Webdings /Wingdings2 /Wingdings3 /Wingdings-Regular /ZapfDingbats /ZapfDingbatsStd /ZWAdobeF /NeverEmbed [ true /Arial-BlackItalic /CenturyGothic /CenturyGothic-Bold /CenturyGothic-BoldItalic /CenturyGothic-Italic /TimesNewRomanMT-ExtraBold /AntiAliasColorImages false /CropColorImages true /ColorImageMinResolution 150 /ColorImageMinResolutionPolicy /OK /DownsampleColorImages true /ColorImageDownsampleType /Bicubic /ColorImageResolution 150 /ColorImageDepth -1 /ColorImageMinDownsampleDepth 1 /ColorImageDownsampleThreshold 1.50000 /EncodeColorImages true /ColorImageFilter /DCTEncode /AutoFilterColorImages true /ColorImageAutoFilterStrategy /JPEG /ColorACSImageDict << /QFactor 0.76 /HSamples [2 1 1 2] /VSamples [2 1 1 2] /ColorImageDict << /QFactor 0.76 /HSamples [2 1 1 2] /VSamples [2 1 1 2] /JPEG2000ColorACSImageDict << /TileWidth 256 /TileHeight 256 /Quality 15 /JPEG2000ColorImageDict << /TileWidth 256 /TileHeight 256 /Quality 15 /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 150 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 150 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict << /QFactor 0.76 /HSamples [2 1 1 2] /VSamples [2 1 1 2] /GrayImageDict << /QFactor 0.76 /HSamples [2 1 1 2] /VSamples [2 1 1 2] /JPEG2000GrayACSImageDict << /TileWidth 256 /TileHeight 256 /Quality 15 /JPEG2000GrayImageDict << /TileWidth 256 /TileHeight 256 /Quality 15 /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict << /K -1 /AllowPSXObjects true /CheckCompliance [ /None /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 /PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/CreateJDFFile false…