DE-A-4799-3 __Rev E (new).pdf

E 08/2◄/23 CHG SHELF LIFE FROM 3 YEARS TO 5 YEARS RC CHV

D 11/01/18 CHG PERFORATED LINE FROM 3.5 TO 4.5 LC CHV

REV 0,1£ OtSCRIPTION CHI C

O .,,.,., DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

MIKE MONRO�EY AERO�IJTICAL CENTER OKLAHOMA CITY, OKLAHOMA

FDIO FLIGHT STRIP - TERMINAL 1/2

""'['0[0"' "-""'""'"' """"""'

L. CLARK CYNTHIA VUONG

==wfff�u"

ISSUED BY ""

09-16-97 "v

ORA>•• fff Ir

Oft.l.WIMG NO

E FAALC ENGINEERING AND

DE-A-4799-3 CH[Ctl[D BY

R

<: PRODUCTION DIVISION

Robert C-CTR Clary Stamp

Robert C-CTR Clary Stamp

Robert C-CTR Clary Stamp

FDIO Flight Strips Terminal 1/2

Paper Box Construction

PAPER EXIT THIS

DIRECTION

MARK "DO NOT REMOVE

THIS TAB"

BOX LABELING

ALL DIMENSIONS ARE INSIDE UNLESS

OTHERWISE NOTED

ALL TOLERANCES ARE +/-.062"

NOT TO SCALE

C .,,,,.1---

PAPER BOX SHOWN WITH

TOP COVER OPEN

BOX LABELING

WINDow SLOT

BOTH SIDES

WITH TOP AND

BOTTOM ROUNDED

GENERAi · Each paper box of THERMAL FLIGHT STRIPS shall hold. 1,000 +/- 50 continuous strips, which are individually folded and perfo rated, at the ends of each strip. There shall be no breaks In the stock and splicing is not permitted. There shall be no noticeable curl to the paper. The dimensions of the paper box are illustrated in this drawing.

BOX CONSTRLJCJION AND PACKAGING· Construction of the box and packaging of the THERMAL FLIGHT STRIPS shall meet the following requirements:

1 . The top cover of the paper box shall be perforated as shown. This will allow the top cover to be removed before the THERMAL FLIGHT STRIPS are loaded into the printer. The two (2) end tabs shall not be perforated.

2. The front tab of the box shall bend down to allow the THERMAL FLIGHT STRIPS to exit freely over the box edge.

3. The THERMAL FLIGHT STRIPS shall be properly loaded and orientated such that:

a. The FLIGHT STRIP exits over the bent over front tab.

b. The Thermally active (green) side Is facing up as the FLIGHT STRIP exits the box.

c. The black registration mark on the rear side of the FLIGHT STRIP shall be towards the leading edge of the strip as the paper exits the box.

4. There shall be a window constructed on each side of the box to allow personnel to visually monitor the amount of FLIGHT STRIPS remaining in the box during printer operation. Details are as illustrated.

5. Boxes shall be constructed of 24PT Cl S Kraft Back.

DO NOT USE STAPLES.

BOX I ABEi ING· THE BOX SHALL BE LABELED AS FOLLOWS;

1. "THERMAL FLIGHT STRIP, TERMINAL 1 /2" ,

2. "Part Number: ________ "

3. "CAGE Code: ________ ", and

4. The two end tabs. at the top of the box shall be marked "DO NOT REMOVE TAB".

DLIS-25406

NSN 7530-01-682-6809

P/N 424187

IFS P/N 100026061

D

C

A

REV

CHG PERFORATED LINE FROM 3.5 TO 4.5 11/07/18

Changed Packaging Quanity Per Box 2/27/18

CHG NOTE 2.a.,THICKNESS TARGET & RANGE IIIOS/13

ADDED NSN NUMBER 75J0-0l-46e•4688 4/21111

DESCRIPTION DATE

DEPARTMENT Of TRANSPORTAHON f£0ERAl AVIATION A0MINISTRArlON

IIQIIIOIC\'......, __ IIJO --or-,.-

CHV

CHV

((Yt,t'J \4-----' (gyj'j/

APPROVED

FDIO FLIGHT STRIP - TERMINAL 1/2

- 9 / 16 / 97[I.Ill

C l-"

.Cl.Ml( D_E-A-4799-3

SHEET 2 OF 3

FDIO Flight Strips Terminal 1/2 Shipping Carton Construction

LABEL : ALL FOUR SIDES AND TOP

"STORAGE INSTRUCTIONS"

AFFIX TO END PANEL

PRODUCT

IDENTIFICATION

LABEL

SHIPPING CARTON CONSTRUCTION AND LABELING

GENERAL· Shipping cartons shall contain ten (10) boxes of individual stocks of 1,000 contiguous fanfold THERMAL FLIGHT STRIPS.

GRADE SIZE· Cartons shall be constructed of material that meets or exceeds the 32- pounds/inch Edge Crush Test (ECT). Reinforced tape shall be placed on all outside closures. DO NOT USE STAPLES.

LABELING· Shipping cartons shall be marked In characters of one-half ( 1 /2") inch up to ( 1 ") inch high on all four ( 4) sides and the top as follows:

1. "STORE BELOW 110°

F AND 85% RELATIVE HUMIDITY"

2. "DO NOT EXPOSE TO DIRECT SUNLIGHT"

3. "DO NOT REMOVE SHRINK 'WRAP UNTIL PAPER IS TO BE USED"

PRODUCT IDENTIFICATION LABEL· The shipping carton shall have a "Product Identification Label" affixed to the end panel that contains the following required data:

Contract Number: ___________________ _

THERMAL FLIGHT STRIP, TERMINAL 1 /2

Contractor's part number: ___________________ _

NSN: 7530-01-682-6809

Quantity: 10,000 strips Production Date: ____________________ (MM/DD/YY).

Expiration Date: ____________________ (MM/DD/YY).

Carton Number: ____________________ of ___________________ _

Characters shall be at least one-eight ( 1 /8") Inch high.

SHRINK WRAPPING OF SHIPPING CARTONS· Shipping cartons shall be individually shrink wrapped and sealed prior to palletizing for shipment In order to prevent the entrance of moisture into the THERMAL FLIGHT STRIP paper. All markings required in the previous paragraphs shall be of a contrasting color that Is visible and readable through the outer shrink wrap.

D CHG PERFORATED LINE FROM 3.5 TO 4.5 11/07/18

C Changed Packaging Quanity Per Box 2/27/18

CHV

CHV

DLIS-25406

8 CHG NOTE 2.a.,THICKNESS TARGET & RANGE IIIOS/13 ((Yt,t'J \4-----'

NSN 7530-01-682-6809

P/N 424187

IFS P/N 100026061

A ADDED NSN NUMBER 75J0-0l-46e•4688 4/21111 (gyj'j/

REV DESCRIPTION DATE APPROVED

DEPARTMENT Of TRANSPORTAHON f£0ERAl AVIATION A0MINISTRArlON

... IIQIIIOIC\'......, __ IIJO --or-,.-

FDIO FLIGHT STRIP - TERMINAL 1/2

- 9 / 16 / 97[I.Ill

C l-"

.Cl.Ml( D_E-A-4799-3

SHEET 3 OF 3

DE-A-4799-3 2 PAGES