Attachment B. 55222CB_RACK HOOD.pdf

8 8

9 40

2x 20

LOCATION OF THE

HANDLE POUCH

7 1 17.5

BLACK

NETTING

BLACK

NETTING

GREY

NETTING

GREY

NETTING

GREY

NETTING

INSIDE HANDLE POUCH POUCH SIDE VIEW

NARROW SIDE WITH

HANDLE POUCH VIEW

WIDE SIDE VIEW

WITH "D" RING

NARROW SIDE VIEW WIDE SIDE VIEW

WITH BELT

TOP VIEW

NOTES:

THE ENTIREITY OF THIS DRAWING REPRESENTS A 1.

RECREATION OF A DRAWING PREVIOUSLY SHARED WITH

THE BEP

THE LOCATION OF THE STRAP HANDLE.2

THESE ENDS OF THE INSIDE HANDLE POUCH TO BE SEWN 3

TOGETHER.

REINFORCE THE MATERIAL BEHIND THE "D" RING TO KEEP 4

IT FROM TEARING THROUGH.

"D" RING TO BE SEWN 10" FROM THE BOTTOM EDGE OF 5

THE WIDE SIDE PANEL. THE "D" RING SHOULD BE A 2" RING

THAT IS ZINC-COATED TO PREVENT CORROSION.

THESE 30" OF THE HOLE-PUNCHED STRAP IS LOOSE AND IS 6

NOT SEWN TO THE SIDE PANEL OF FABRIC. THE VIEWS ON

SHEET 1 DO NOT SHOW THE SLACK IN THE PERIMETER

COVER BELT, SO THE DIMENSIONS ARE NOT NOTED UNTIL

SHEET 2.

THIS FEATURE REPRESENTS THE CLASP THAT WILL BE 7

LOCATED ON ONE END OF THE PERIMETER BELT.

REINFORCE THE MATERIAL BEHIND WHERE THE BELT IS 8

SEWN TO KEEP IT FROM TEARING THROUGH.

4" OF THE UNDER CART BELT IS TO BE SEWN TO THE WIDE 9

SIDE OF THE HOOD

8 8

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

Nonpublic Information: The information on this page is nonpublic information provided by the United States Department of the Treasury, Bureau of Engraving and Printing (“BEP”). As such, the information herein shall neither be duplicated nor disclosed to any third party without the express written consent of an authorized representative of the BEP. All rights, proprietary or otherwise, are reserved by the BEP.

DATE APPROVEDDESCRIPTIONREVZONE

REVISION HISTORYREVISION

STATUS

REV SHEET

TOLERANCES UNLESS OTHERWISE SPECIFIED

INTERPRET DIM

AND TOL PER

ASME Y14.5-2009

88002

CAGE CODE817-891-7230

DJWCHECKED

UNLESS OTHERWISE

SPECIFIED, ALL

DIMENSIONS ARE IN

INCHES

HJNDRAWN

14TH AND C STREETS SW WASHINGTON DC 20228 USA

-.004 -.020

+.016

ALL HOLES TO H12 TOLERANCE UNLESS OTHERWISE SPECIFIED

.5 1 OF 21:10

NONE

NONE

SEE SOW

ENGINEER

.25

X/X .XX.X .XXX ANGLES

HALEY NEU

.25 .25 .25

U.S. DEPARTMENT OF THE TREASURY

BUREAU OF ENGRAVING AND PRINTING

OFFICE OF ENGINEERING

MATL

MATL TRTMT

SURF TRTMT

55222CB

RACK HOOD

D -

03/30/2021DATESCALE SHEET

TITLE

DWG NOSIZE REV

12x 0.38 0.0625 THRU

11x 2.38 x

.5

±0

.0

120 3010

SCALE 1 : 2

3.2512x 2.50

13x 0.50 ±0.0625 THRU x

±0

.0

4 30 35

11 SCALE 1 : 2

COVER PERIMETER BELT

UNDER CART BELT

NOTES:

THIS FEATURE IS THE CLASP MENTIONED IN THE SMALL SECTION BELOW THE COVER 10

PERIMETER BELT VIEW. THIS CLASP SHOULD BE LARGE ENOUGH FOR THE 1" PERIMETER

BELT TO FEED THROUGH.

THIS SECTION OF THE UNDER CART BELT REPRESENTS THE 4" OF BELT LENGTH THAT IS TO 11

BE SEWN AND REINFORCED ON THE "WIDE SIDE VIEW WITH BELT" VIEW SEEN ON SHEET

1 OF THIS DRAWING.

THE COVER PERIMETER STRAP IS SEWN ALONG THE BOTTOM EDGE OF THE FABRIC 12

PANELSOF THE RACK HOOD. THERE SHOULD BE A CLASP ON THE END, SO THAT THE

OTHER END CAN BE FED THROUGH AND TIGHTENED. THERE SHOULD BE 30" OF BELT

FROM THE OPPOSITE OF THE CLASP THAT IS NOT SEWN TO THE RACK HOOD. THIS FREE,

UNSEWN END SHOULD HAVE A SERIES OF PUNCHED HOLES WHICH WILL BE USED TO

FEED THE SECURITY TAG THROUGH.

AT THE END OF THIS BELT THERE SHOULD BE FOLDED AND SEWN FEATURE ALONG THE 13

BELT (BETWEEN THE FREE END AND THE FIRST HOLE) TO HELP IT SECURELY REMAIN IN

THE PLASTIC CLASP.

ALL PUNCHED HOLES SHOULD HAVE NON-FRAYED EDGES, SO THAT THE SECURITY 14.

TAGS CAN BE SEALED.

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1

E

F

E

F

Nonpublic Information: The information on this page is nonpublic information provided by the United States Department of the Treasury, Bureau of Engraving and Printing (“BEP”). As such, the information herein shall neither be duplicated nor disclosed to any third party without the express written consent of an authorized representative of the BEP. All rights, proprietary or otherwise, are reserved by the BEP.

DATE APPROVEDDESCRIPTIONREVZONE

REVISION HISTORYREVISION

STATUS

REV SHEET

TOLERANCES UNLESS OTHERWISE SPECIFIED

INTERPRET DIM

AND TOL PER

ASME Y14.5-2009

88002

CAGE CODE817-891-7230

DJWCHECKED

UNLESS OTHERWISE

SPECIFIED, ALL

DIMENSIONS ARE IN

INCHES

HJNDRAWN

14TH AND C STREETS SW WASHINGTON DC 20228 USA

-.004 -.020

+.016

ALL HOLES TO H12 TOLERANCE UNLESS OTHERWISE SPECIFIED

.5 2 OF 21:10

NONE

NONE

SEE SOW

ENGINEER

.25

X/X .XX.X .XXX ANGLES

HALEY NEU

.25 .25 .25

U.S. DEPARTMENT OF THE TREASURY

BUREAU OF ENGRAVING AND PRINTING

OFFICE OF ENGINEERING

MATL

MATL TRTMT

SURF TRTMT

55222CB

RACK HOOD

D -

03/30/2021DATESCALE SHEET

TITLE

DWG NOSIZE REV