Attachment 6 - Standard Fence Specs.pdf
PDF 222 KB Posted
- Attached to
- JC-PRRD-Riparian Enclosure Fences
- Solicitation number
- 1240LT22Q0126
View the file
Other files
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
UNITED STATES DEPARTMENT OF AGRICULTURE
FOREST SERVICE-PINE RIDGE RANGER DISTRICT
Type/Purpose of Fence:
Township / Range / Section Length of Fence (feet)
Wire
Wire Type:
Number of Wires
Gauge and Galvanization (All wires)
Number of strands per wire (All wires)
Tensile strength (psi) (All wires)
Wire wrap at braces
Fasteners
Barbs
Top wire height, distance to 2nd wire
Bottom wire type & height
Any other wires
Line Posts
Type
Size, length, wall thickness
Depth
Spacing
Stays
Stay Type
Stay Spacing
Corner, Gate & Brace Posts
Type and Size
Post Length and Depth
H Brace assembly spacing
Horizontal Brace Material
Type of material
Size | Diameter & wall thickness
Length
Sec. ____
Vanessa Yeoman: Rangeland Specialist
Planner : Title:
Twp. ____
Rng. ____
4/22/2021 Date
Location Map
2 point 14 gauge about 4-6 inches apart
Cattle / Smooth wire 16" - 18" from ground
3" x 6' 5.5' w/anchor
Double Strand
Standard weight
Wheel__GPS__Photo__
2' 1.5'
16' Reccommended, 20' maximum
Not Applicable
Double wrap wire
9 gauge Staples 1 .5 " long
Treated Wood Steel T Post
Steel Pipe
7.0' minimum
2 3/8" dia. x with 0.125" wall thickness pipe
Cattle / (Deer-Antelope) 38", 12"
30' maximum
Steel Pipe Sealed top 2 3/8" OD (MIN.) .125" thick
7' long 3' deep
1320' or less & at Angle Changes > 15 degrees
Galvanized, twisted wire
FENCING SPECIFICATION SHEET
Specialty Fencing
Planned Applied
Township Range Section
Barbed wire Wildlife Friendly
12.5 gauge galvanized
FOREST SERVICE: PINE RIDGE RANGER DISTRICT
Additional Planning and/or Application Notes
Date: 04/20/2021
Notes: Work Specifications are listed below (also refer to the attaching drawings and specification sheets).
1. Fence Type: The fence will be wildlife friendly with the following specifications:
a. 3-Wire Fence.
b. Smooth bottom wire spaced 16" above the ground.
c. The middle wire will be barbed and spaced 10" above the bottom wire.
d. The top wire will be barbed and spaced 12" above the middle wire or will be spaced at a maximum of 38" in height.
2. Post Spacing: Posts will be spaced 16' apart or at a maximum spacing of 20'.
3. Wire: The wire will be double stranded and a minimum of 12.5G.
4. Barbs: Barbs on wire will be 2-point 14G and will be spaced 4-6” apart.
5. Post Ratio: There will be a maximum of 3 steel t-posts to every wood post. Unless topography will only allow for steel t-posts.
6. Post Depth: The steel t-posts will be buried at a minimum of 1.5' deep, the wood posts will be buried at a minimum of 2' deep, and corner, gate, and brace posts will be buried a minimum of 3' deep.
7. Line Posts: A minimum of 3”x6’ pressure treated wood posts will be used. A minimum of 5.5’ t-posts with an anchor will be used.
8. Brace Posts: H-Braces material will be 2 3/8" steel pipe with a 0.125" wall thickness and sealed top or a substitute of 5"x7’ pressure treated wood posts can be used. H-Brace materials will be 7' long (as approved by the contracting officer).
9. Horizontal Brace Material: H-Braces will be a minimum of 7’ in length. The horizontal brace material will be 2 3/8" steel pipe with a 0.125" wall thickness.
10. Number of Braces: Braces are required at every corner, gate, and angle change greater than 15 degrees. Braces should be installed every 1,320-ft intervals or closer.
11. Brace Wire: The wire around H-Braces will be double wrapped at a minimum.
12. Staples & Clips: Fence staples will be a minimum of 1.5" and 9G steel and manufacturer fence clips or 12G wire can be used for steel t-posts.
FOREST SERVICE: PINE RIDGE RANGER DISTRICT
Corner/Gate and Inline Brace Checkout Tool
Name Unit Fence Type:
Number of Wires
Livestock Type
Enter measurements in colored cells in the drawing below
Top wire Direction of Pull
in. Brace Material length
ft. in. Height of Top wire
3.2 ft.
Post Height in.
4.0 ft. in. Height of Brace Material degree angle 3.3 ft.
Post Depth in.
3.0 ft.
Material or construction feature Measured Criteria Met
Post Height - Above ground in. in. min
Post Depth - Below Ground in. in. min
Brace Material length in. in. min
Brace Material height in.
in. in. min o o max
: 1 : 1 min
Top Wire Height
Angle (degrees)
Ratio of Brace length to height
Criteria
Cattle
Corner/Gate and In-line Brace Measurement Checkout Tool
USDA Forest Service East Ash, Chadron Creek & Bordeaux
Specialty Fencing
7.00
25.5
Ground
25.5
2.1
Yes
Yes
48 Yes
Yes
Yes
Yes38
File details come from the government source that posted it. Updated .