ATTACH_mil_c_29433 (1).pdf

MIL-C-29433(MC)

8 “JUNE.1987

MILITARYSPECIFICATION

CAPS,C~ISON: MEN’S,

This s=ification is =Droved for use bv U. S. Narine the Na’w. ard is availtilefor w bv &l. .

Departmentof Defense.

1. .SCOPE

1.1 E22Es. ‘lhis

caps.

1.2 Classification.

ard sizesas specified

Class1 - Cap, Class2 - Cap, Class3 - Cap, s~cificationcovers

The caps shallbe of (See6.2):

Departments Corps,Departmentof and Pqenciesof the requirementsfor men’s garrison one typ in the followingclasses

Polyesterfi$=ml,Gabardine,Green2212 Gabardine,ml, Green2210 Elastique,~ol, Green2222

Scheduleof sizes

6-3/8 6-7/8 7-3/8 6-1/2 7 7-1/2 6-5/8 7-1/8 7-5/8 :

6-3/4 7-1/4 7-3/4

2. APPLICASIE~

2.1 Governmentdocuments.

2.1.1 Specifications, standards, and handbooks. The foilowinq spscifications,and handbmks forma prt of this s~cificationto tfieextent specifiedherein. Unlessotherwisespecified,the issuesof thesedocunents shall be those listed in the issue of the Eepsrhnentof EefenseIndex of S~if icationsand Standards(DODISS)and supplementthereto,citsd in the solicitation.

Beneficialcwments (recamnendations,dditions,deletiona),and any p2rtinent data whichmay Ee of use in improvingthisdocunentshouldte a3dresaedto the Ccnmandantof the Marine Corps (IMA-1), Headquarters,U. S. Marine Corps, Washington,N 20380,by usingthe self-addressedStandardizationOocunent ImprovementPropxsal(DD Fotm 1426)ap~aring at the erd of thisdccunentor by letter.

AMSCN/A FSC 8405

DistributionStatementA: @proved for public release; distrib~ion is unlimited.

Source: https://assist.dla.mil -- Downloaded: 2022-03-11T21:15Z Check the source to verify that this is the current version before use.

MIL - 29433(MC)

SPECIFICATIONS

FEDERAL

v-T-276 - ‘lhread,Cotton.

V-T-301 - Thread,Silk.

NWP-71 - Pallet,MaterialHandling,Wed, stringer

Constructionr2‘Way and 4 Way Ehtry(Partial) CCC-C-461 - Cloth,TwillUnifo$nrCotton.

DDC-L-20 - -l; For Clothing,!2wipage,Srd Tent.age, (@neral Use).

MILITARY

MIL-C-368

MIL-C-3577

MIL-C-3738

MIL-C-10176

MU-C-10296

MIL-P-15011

MIL-B-17757

- Cloth,Satin,Rayonand Cloth,mill, Rayon.

- .%eatband,Headgear(Lest.@)

- Cloth,!dlastique,hbol

- Cloth,Gabardine,Ekml,Polyesterand ml.

- Cloth,.Sateen,Cotton.

- Fallet,MaterialHandling,W, Post ConstrutiiOn, 4 Way ~try

- Eoyes,Shippiw, Fiberkmard(McdularSizes).

STANDARDS \

FEDERAL

FSD-STC-751 - Stitches,,fisamsand Stitchings.

MILITARY

MIL-STO-129 - Markingfor Shipnentand Storage.

MIL-STD-147 - Ps+letizedUnitLoads.

MIL-STD-901 - Provisionsfor EvaluatingQualityof caps,@rriSOn, Men’s.

(Copiesof ?@cifications,stardards,handbcds, drawings,ti publications requiredby manufacturersin connectionwith s~cific acquisitionfunctions should be obtained frcm the contractir%jactivityor as directedby the contractingofficer.)

2.1.2&her Governmentdocurents,drawings,and publications.The following other Governmentdc.mnents,drawi~s, ~ publicationsfo~ a Prt of this spcificationto the extentspcified herein. Unlessotherwisespcified,the issuesshallEe thosein effecton the dateof the solicitation.

MIkC-29433(MC)

LAWSAND REGULATIONS

U. S. FestalServiceManual

(Applicationfor copies should be. addressd to the Superintendentof ~unents, U. S. GcverrmentPrintingOffice,Washi@on, D.C.20402.)

2.2 Other publications. ‘l’hefollowingdocurent(s) form a p=mt of this s~cifIcatlonti the extentspcified herein. ~less otherwisespecified,the issuesof the dccumentswhich are DoD adoptsdshallte those listed in the issue of the D3DISS spscified in the solicitation. unless otherwise spscified, the issuesof docunentsnot listed in the DDDISS shall be the issue of the nongovermmsntdccumentshhich is currenton the date of the solicitation.

UNIFORMCI.&3SIFICATIONCOMMIITEE

UniformFreightClassificationRules

(Applicationfor copies shouldbe ddressed to the UniformClaasification Ccmmittee,Room 1106,222 SouthRiversidePlaza,Chicago,Illinois 60606.)

NATIONALkKYD2RFREIGHTTRAFFICASSCX21ATION,INC.,~

NationalMotorFreightClassification \

(Applicationfor copies should be addressedto the American Trucking AssociationInc.,‘ltiriffOrderSection,1616P Street,N. W., ~shington,D.C.

20036.)

2.3 Order of precedence. In the event of a conflictbetweenthe text of this specificationand the referencescited herein (exceptfor associated details~cifications,specificationsheetsor MS standards), *% text of this sPscificationshalltake precedence.Pkthirqin this s~cification,@wsver, shall supersde applicablelaws and regulationsunlessa specificexeaption haa beenobtained.

3. R!32UIlWfSWl?S

3.1 Standardsamples. The standardsampleis furnishe3solelyforguidance and informationto the supplier(see6.3). Variationfromthis specification may ap~ar in the sample,in whichcasethe specificationshallgovern.

3.2First article. men specified(see 6.2), contractor samplecaps for firstarticleins-ion ad approval.

3.3 Naterials.

shall furnish

3.3.1BasicIT@terial.The basicmaterialfor each classof cap shallk as follows:

(a)Class 1. Cloth,10.6ounce@ yester/wolgabardine,grer+ shade 2212conform-type II,class12 of MIL-C-10175.

MIL-C-29433(MC)

(b)Class 2. aOth, 14.5 oupce WJO1 qabardine,green shade’2210 conformimgto t~ 1, class5 of MIL-C-10176.

(c)Class 3. cloth, 18 ounce WO1 elastique,green shade 222 conforrnirgto typ II, class1 of MIL-C-3738.

3.3.2Lining. The msterialfor liningthe class 1 caps shall te cloth, rayontwill,3.7 ounce,green shade’2208 (see6.3), ~nfo~ing to class1 Of MILcC-368.

3.3.3Sweatk=nd. The materia3for the sweatbarxlshall be cloth,cotton, uniformtwill,green ehade2224 (see6:3),8 o~ce, ~nfo@n9 to t~ IIIof CCC-C-461,exceptthe requiranentsfor colorfastnessto bleachingand light shallnot apply,or cloth,aateen,cattOn,olive9reenshade107conf0~in9 to CkSS 1 of MIL-C-10296. AS an alternatefor classes2 and 3 caps only, a leathersweatband,dyed brown,not lesst.haq7/8 inch in widthand canforrning to MIL-S-3577may be USed. The leathersweatbandshall& embossedwith an imitationturnedline 1/8inchfranthe top edge.

3.3.3.1%eatbaml reinforcement. If tie alternateleathersweatbandis used, the rateri.slfor the swattand reinforcanentshall be 5/8-inch-wide stripof ei+~erprintclothor sheetingthat is lightlycoatedon both sides with proxyltior vinyl.

3.3.4Thread.

3.3.4.1Cottonthread. The cottonthreadused typ IC2, 3 ply, ticketNC. A and for overedging 70 conformirqto v-T-276.

for insidesaminq shallbe type IA3, 2 ply, tickett@.

3.3.4.2Silk thread. The silk threadused for topstitchirqthe top crowm ad hmnimg the curtainshallix typs 1, 3 ply, sizeA conformingto V-F301 .

3.3.4.3Colorand colorfastness.The cottonand silkthred shallk green shadeT-1, @ble No. 66023. ‘lhe~reads, tien testedin accordancewiththe applicabletired -if ication,shallshowgocd fastnessto wet-drycleaning ad light.

3.3.5Eyelets. The eyeletsshall be brass, rolledflangetype, with the barrelscoredwith 6 to 8 scores. The flangeof tie eyeletshallbe enameled a shadeto closelvmatch the shadeof the l=ic msteri~ (s= 3.3.1)J or the entire eyeletma; be enameled. ~elets with a washer may be eyelets,when testedaa spebified in section4, Table IV, shall

MIL-C-29433(MC) ,

tie requirementsspcified herein.

dimensions:

Outsidediameterof outsidediameterof

The eyeletsshallconformto the following barrel,inch: 0.185~ 0.004 flerme.inch: 0.312+ 0.005. . .

ungth of barreltier flarge,inch: 0.145T 0.004 f.!etalthickness,inch: 0.008~ 0.001

3.3.6wk. Eachcap shallhavea combinationidentification,instruction and sizelabelconformingto typ5VI, class4 of DDBL-20, excepttie content shallinclulethe nameof contractor1/ and the Wol Prcducts& information.

The label shallmeasurenot less & 1-3/4by 1-1/4inches,with a minimn 1/4-inchmarginat the top edge for .SeWin9.The caps are intendedto ke dry cleanedad shallshow fastnessto dry cleaning.

Nomenclature(itemidentification) Contractnunter Nameof contractor Size NationalStock-r hbol PrcductP&

DRY CLEANONLY

3.4 Eesign. ‘Ihecap shall& the cl.S. MsrineCorpsdesignshownbn Figures land2.

3.5 Patterns. Stadard ~tterns will & furnishedto the contractorby the Government. ‘Thestandardpstternsshallnot k alteredin any way and shall be used only as a guide for cuttingthe wxking pstterns. ‘he standard patternsprovide l/4-inchseem allowance,exceptas otherwisespecifiedin Table 1, show size and are marked or notched for the pro~r cutting, placement,.3rdassemblyof the crmpnent parts.

3.5.1List of patternparts. Caps shall te cut frommaterialss+cified hereinin accordan= withthe patternpati indicatedbelow:

PatternNomenclature

No. of Item Easicmateriel cut parts

1. Sidecrown 2

2. Curtain(class1) 2

3. Curtain(class2 and 3) 1

4. Top crown 1

Materia3.:Cloth,Rayon‘l’Will(Class1)

5. Lining,sidecrowm 2

6. Linirq,top crown 1

Size of charactersfor name of contractorshall be mininvm 6 pint approximately1/16inch).

3.6 Construction. The caps shall be manufacturedin accordancewith the operationsand the stitch,&am, and stitchingtypes s~cified in Table 1.

The contractoris not requiredto followthe exactsequenceof operationsas listedin Table 1, but all oprations s~cified shallbe usedto manufacture the caps.

3.6.1Stitches,seams, and stitchim?s. The stitch,seam, and stitching typssspecifiedin TableI shallconfo~ to FEFSTW751. Whenevertwo or nmre stitchor eeamt~s are spcified for the sameoperation,any one of thenmay be used. The nunberof stitchesp?r inch as sp?cifiedin Table I indicates the minirmrnad maxtiunnunberpermittd.

3.6.1.1Serqestitchinq. Xrge stitchirqshall~ done on sergingmachines having a knife attacinnentpropsrlyset to trim we raveledsdge without cuttingthe material.

3.6.1.2Tackingand backstitchiw. tis of seams and stitchingprcduced with 301 t~ stitch,when no? caughtin other seamsor stitchirq,shallbe backstitchednot less than 1/4 inch. Threadbreaks(all-itch t~s ) shall h securedby stitchingback of breaknot less‘zhan1/2 inch.

3.6.2 Shade markinq. me ccmponentparts shall be marked to insurea uniformshadeand sizethroughoutthe cap. AIIymethcdof shademarkingi-rayEe usedexcept: \

(a) Corrosivemetaldevices.

(b) A3hesivetype tickets *ich ahow discolorationand adhesive mass which adheres to t~e raterial umn removal of the

1.

tickets.

(c) %-on shadetickets.

TABLEI MANUFACTURINGREQI

OPEUATION SIT]!

rY1~}:

S@!.23-.

a. w the cap in strictaccord-ancewiththe ptterns furnishedby the Government.

b. Cut the materialin the direc-tion indicatedby directionallines on hk patterns.

c. Cut the !..001and plyester/wool psrtsof the cap frcmone pieceof the basicmaterial.

d. Cut the liningfor the Class 1 cap frcm one piece of the rayon twillmaterial.

t)

EMENTs

SEAMI

SI’CH

TYPE

lK)B/

1.PR

No

1.

2.

3.

4.

TABLEI MANUFACTURINGRSQLT

OPERATION

!?QJ!$!.(mn’t)

e. cut the sweatband On the straight(warpOr fillin9direction) of the cottonmterial. The sweat-band shallbe cut 1-5/8incheswide ti sufficientlyIOW in Order ap the ends 3/4 inch,wth tie nd turned undernot less than nch.

to top 3/8

k. Replace,at timeof cutting,all =rts of the cap or liningmaterials :ontainingholes,seriouslywAcen- .xqdefectssuchas mashes,multiple :loats,loose or weakeningslubs, ?tc., expected to develop into e ~ole, shade bars, dye streaks.OK mslightly Sltis, etc., affectl~ appearance.

). Replaceany psrt damaqe5durir!$ manufacturingprocess by needl< ;hews which may be expected tc ievelop into a hole, =issOrs 01 cnife cuts, tears, holes, mends mrns ad largedrill hcles in thf mterial affectiW ap~arance.

Shademarking.

a. Mark all component parts a!

spcified in 3.6.2, in order ti insure a uniform shade and siz( throughout the caP and ProPe assembly.

Make curtain(Class1).

Finishedap~arance. The curtai shall & uniformly stitched an shall he snccth and flat withou twists,gathers,puckers,or Pleats

a. The curtainshall& madeof tw pliesof basicmaterial.

YENTS

?.AM/

rcll fPE j

ND!. 130BI

I.PR

4, TABLEI

MIGC– 29433(MC)

MANUFACTURINGMOUIREFiENTS

3. Positionthe two plies face to Eace,tith edges even and notches natching. Stitch tcgetherwith a l/4-to 5/16-inch sew alocg the Jpperedges.

:. ~rn curtain, forcing ox the seam. Uniformlyedgestitch1/8 inch Franseamededge.

i. Closetmttanof curtainuniform- Lywith 3/16 to l/4–inchseam.

>rge stitchcurtain,top and side :rowns(Class2 and 3).

Finisheda~arance. ~e curtain, LOp and side crowrs shal1 be pro~rly sergestitched.

a. Serge stitch raw top edge of curtain,all rawedgesof top crown, am3 side cro’m except tmttmj raw edge of side crown. Wnen ~rging raw &ges, care shall be exercised in eettinq the gage so that the raveld dge onlyof the materialis trisnwdoff.

Hem curtain(Class2 and 3).

Finishedap~arance. The hem shall be uniformly stitched without pleats,puckersor twists,and shall k onifonnin width. ,

a. Hem the serged edqe of the curtain 1/4 to 3/8 inch with tine stitching1/16 inch fr6m the folded edge.

Joinendsof curtain.

Finishedap~arance. ‘Iheends of the curtainshallbe joinedwithout twists,fullness,or puckers.

1:

1:

5:

or

F.AM/

Tell

YPK

+2 (a) se-2 (b)

Sa-1

Fd-1

Fd-1

Fa-1

Fa-1

S’1’CH/

IN

12-16

10:4

12-16

10:4

12-16

10:4

6-8

6-8

12-1(

12-16

Nr)l, A

A (sil

A

10/2

10/2

A ~silk A ;silk

BOB/

I.PR

A

A

A

70/2

70/2

A

A

Yo

-i

MIL-C-29433(MC)

TABLEI MANUFACTURINGREQ[

OPEHATION ST’(:II

m’1~1:

Joinendsof curtain.(con’t)

a. I+ the left end of the curtain over the outsideof the rightend, with the Eottc$nedges even and the frent notches matching. seam tcgether alonq the hottcrn1/8 to 3/16 inchframthe rawedge.

Maketoo crown(Class1).

Finishedappearance. The top crown 1ining shall not be tight, short, or twisted,affectingsncothnesson the outsideof crown. !he folded edge of top crown-liningasse.rbly shall be stitchedwithout twists, puckers,pleats,or distortion.

a. !tbpcrown shallbe made of one ply of basic materialand one ply of liningmaterial.

b. position lining on underside of crown, with edges even and notches matching. Sean together 1/8 inchfran rawedges.

c. Ebld crown-liningassembly in half lerqthwisewith lining side out. Stitchalorxgfoldededge fran ed to end. The line of stitching shall tsper from zero at each end to 1/8 to 3/16 inch frcm folded edgeat the center.

d. Stitch the folded top crowm-liningassembly3/4 ~ 1/8 inchfrom rawedge.

Jointop crowm(Class2 and 3).

Finishedappearance. The top crown shall be joined tcqether wi+fiout twists,puckers,pleats or distor-tion.

a. Fold top crown wise with eerged notches matching. 4in half length dges even Stitch along

3rr1

EMENTS

SEAMI

STCII

IYPE

S.%-1

SSa-1

Osf s%- 1

Osf-1 s’rcH

IN

12-

12-

12-

12-

8-1

Nr)l.

A

A

A

A

A rwlR/

I.PR

A

A

A

A

A

9.

10.

11.

MIL-C-29433(MC)

TABLEx MAtiUFAcTuRINCwouI

OPERATION

Jointop crown(Class2 and 3).

(con’t) fold edge from end; the line of stitchingshalltaper from zero at each end to 1/8 to 3/16 inch from foldsdedgeat center.

b. Stitchtop crown 3/4 ~ 1/8 inch fransergsdedge.

Jointop and sidecrowms.

Finishedappearance. The top and side crowns shall he joined to-gether without twists, puckers, pleats,or distortion.

a. Position the left and right side crov.mon the outsideof the respective top crown, with top edges even ad the pint at each end of the top crown matching the notchesin the side’crowns.

b. Join the left and right side crowns, respectively,to the top crown with a l/4-inch seam, tqinniq and endinq on the top crown1/4 inchfraneachend.

~ to ca (Class1.

Finished appearance. The side crown liningshallbe joinedto the cap withouttwists,puckers,pleats or distortion.

a. Positionthe leftand riqhtside crown lining, res~ctively,on the lininq side of top crown, with edgesevenard notchesmatching,and join to the top crown-sidecrown seam outlet with a 1/4-incheeam.

The seam shallbeginand end on tie center fold of the top cro%m 1/4 inchfraneacherd.

S’1’cll v Iv:

1::

EMENTS

SEAM/

SI’cll

1’YPE

%-1

SJ;2

;ss-1 sTcH/

IN

8-12

0-14

-z

0-14

A

A

A rrml

I.PR

k

X(I

72-

MIWC- 29433(MC)

TABLEI MMiUFACTURINGREQUIREMENTS

OPEHATION S’i’(:11

TYPE

Joinendsof sidecrown.

Finishedappearance. The ends of side crownshallbe joinedtogether withouttwists,puckers,pleats,or 5istortion. The centerof the top crom shall be in line with the front and back seams of cap. The stitchingshall not exterd to the top edgeof the sidecrown.

Class1— .

a. Join the left =5 right side 301 crownsat frontarr3backetisof cap with a 3/8-inchseam at the lower end,tapxing to 1/4 inchat tie top crownjoiningstitch.

Class2 and 3.

b. Join the left ad right side 301 crohnsat frentand tackendsof cap with a l/4-inchscan frcmthe lowsr sergededge up to the notch.

Joinendsof sidecrownlining (Class1). I Finishedappearance. The ends of the side crown lining shall be joined without twists, puckers, pleats,or otherdistortion.

a. Join the left and right side 301 crown liningat frontand back ends of cap with a 3/8-inchseam at the lower end tapring to 1/4 inch at the top crowsjoinirgstitch.

Topstitchsidecrown.

Finish@5appearance.The sidecrown shallbe uniformlytopstitched.Cm Class 1 caps,the sidecrownlining at frent and backends of cap shall not he caughtin the topstitching.

I?mll I’cll

YPE

‘SZ-3(

SZ-3

(a).

S&i-1 s’rcH/

IN

10-14

8-12

10-14

ND],

A

A

A llOB/

I.PU

A

A

A

No

15.

16.

MWC-29433(M’C)

TABLEI MANUFACTLX

OPEHATION

3. Thrncap rightsideout,working mt the up~r frontand backcorner% Spreado~n the seam at eachend of cap and tqstitch each side crown 1/16 inch from the eearn. lMrn the side-topcrown joiningseamtowards the side and cont@e to topstitch each side crown 1/16 inch from the raised edge, catchingthe side-top crownjoiningseamin the stitching.

NCYTE: Class1. ‘Ihetopstitchingat eachend of cap shallnot be through tk sidecrom lining.

b. On the finished=P, the widthof the top crotvnshall be 3/4 ~, 1/8 inch,measuredfrcm raisededge of side crowns with the spread fully extended.

Joinliningto sidecrov.m(Class1).

Finished a~arance. The lipi~ shallbe joinedto sidecrownwith-oot twists,puckers,pleatsor o~er distortion.The frentand’bsck,*am of lining and side crown sha+l match.

a. ‘llrrncap wrong side\out,match-ing the frontand back liningseaps to the res~ctive crownseam. Join liningto side crown 1/4 inch frcxn raw tottcrnedge of croyn,with the front and back seam of side crown lining turned flat against the res~ctive sidecrownseamsand with the endscaughtin the stitching.

Joincurtainto cap.

Finishedappearance. The curtain shall fit closeto sidesof the:cap without pleats or puckers. The right and left ends of the cu~ain shall crossat the center’frent 1/2 inch below the top end of the side crovmseam.

!fSNTS W41 I’cll l’PE

SZ-3

(b) ends .&Ii;

raise dge)

Sa-1 s’rcH/

IN

12-16

10–14

ND1,

A (sil

A noB/ l.PR

A

NO

l— 16.

I

1- 17.

MIIrC-29433(MC)

TABLEI MANUFACTURINGREQU

OPERATION

Joincurtainto cap. (con’t)

a. ‘lUrntie cap rightsideout and positionthe curtainon the outside with httcm edges even and notches in curtainmatchingthe frentseam.

b. Join the curtain to the cap throughthe liningwith a 3/8-inch seam, and with the front and back seaw turned flat aqainstthe bcdy of the cap and caught in the stitching.

c. m the finishd cap, the left erd of the curtainshalloverlapthe right eti 4-1/2 ~ 1/4 inches,as itiicated on Figure 1, measured along the kttcm finishede59e of the cap.

Join sweatbandto cap.

Finishedappearance. The sweatband shallk smoothlyand evenlystitche to the cap,withoutwrinkles,pucker gathers,twists,or otherdistortion The sweatbad shall cover the raw bottanedgeof the curtain,withthe loweredge of swsat.bard1/8to 3/16 inch shovethe bottcmfinishede3ge of cap. The ends of the swsathacd shallfinishto the rightOr leftof but not on, the back seam for the crov.nand shall lap each other not less than 3/4 inchwiththe top end turnedtier not lessthan3/8 inch.

The combination identification, instructionand size lakelshallbe placedto the rightor left of the back seam of the crownwith the top enl underthe sweafz.

a. The sweatband shall finish 1 + 1/8 inchwide.—

b. ‘lhrndowm the curtainand psi-tion the xatband on the insideof cap, with both side edgesof swaat-band turnad under in line with the

S’lcll mw

M5NTS

;F.AM/

;Tcll

ITPE

S.%-1 r..%-1 (each dge ) s’rcHI

IN

6-10

10-14

Nflr.

A

A mB/

I.PR

A

A f., :

MIH-’29433(MC)

TABLEI WUFACTURING REQU

OPEUATION STCII

ryl~;

reinsweatbandto cap. (con’t)

;titchimgjoining the curtain snd ;ide crown. Stitch the sweatband iu-oughcurtainand side crown 1/8 ,nchfran each foldeddge, catchihg tie turned-tier pxtion in ~e ;titchingand leavingone end free forattachingthe label~

;. ‘llm underand lap the freeend )f the swathand on the o~site WI. Placethe top end of the label tier the uppr freesdge of awat- >and. Securethe free end of the ;weatbandto the cap @th a row of Stitches1/8 inch fran the folded l~r and 10w5rer3ges,:catchinqthe :urnsd-underprtions spd the label inthe stitching.

3. Turnup the curtain.

2. when the leather awsatbardis Jeedin lieuof the cottonsweatband Eor class2 A 3 caps,the curtain

- side crown shall be overedge stitchedtcqetherat ye bottcln edges. (see17f) :

f. The leatheraw2atkardshall be zut to the reqoired length. ~ e ends of the sweatband shall be abuttedand joined wi~ a row of zigzag stitchicgreinforcedon the undersidewitha atripof the coated cloth.

9. ‘he sweatbandshall ~ zigza9 stitchedto the cap on the inside throughthe curtain eeaq allotiCe and side pieces,with the atitchinq on the tottanedqeof the sweatbsnd.

The cmnbinationidentificatiOn!size lsJx?lshall be camht behind:the sweatband during this jo~ning operation. The curtain shall be turnd up.

I or

MsNTS

EAM/

Tell

YPE

s+ 1

Ssa.–1 s%- 1 tsa-1

5TcH/

IN

8-12

1o-1

1o-1

8-12

NDI

A

A

A

A rmR/

I.PR

A

A

A

A

Vo

I.-

TABLEI MANUFACTU

OPEP.ATION

Joins~at~ to cap. (cOn’t)

NC?T3:The capsmust be c.anpletely.

set and pressedL&ore sewingthe leatherswatbard (see owr. 19).

h. ‘mm dotm tie curtainti stitct the curtainto the side crown 1/1( inchfranraisededge.

Cleancap.

a. Pull and remove all basting thread. him all ends of stitchi~ and rerovea3.1looseends of tireai fran the cap. RmOve all spts, stains,shade ticketsand marking:

without injuryto the material.

Presscaps.

Finishedappearance. The top crowr shall not extend beyond the topstitched upper edge of sid< crohns. The frent and tack of ca~ curtainshallnot he creased.

a. Inserta sideshapr betwen tlx cap curtainand eachsidecrown,am spread the curtain smoothly ti evenlyon the sha~r.

b. Press the cap smooth ard flat with a heated pressingmachine o] heated pressing iron, carefull> folding and creasing the htt~ edge. The pressingshallte done it sucha mannerthatthe seamsjoinin~ sidecrownsto top crowmwillfinisl at the top adge of cap ad the sweatbandwillnot be exFOsedkeyom the bottanedgeof cap.

c. Removeall pressirqmarks.

MENTS

E&T :Tcll

YPE

i%-

N!r)l.

A rirml

I.PK

A

No

-m

TABLEI MANUFACTURINGREQU

Finished appearance. ‘he eyelet shall be properly psitiond and securely attached through the outside of the left side of the curtainand securelyclinchd on the inside without distorting and cutting material or splittingthe flangeof the eyelet.

a. Mark the left side of the curtain l-1/4~1/8inches from the top edge 2 +1/4-1/8 inches fran frentof cap when laidflatas shown in Figure1.

b. Attachthe metal eyeletto the curtainat the mark. ~

\.7 Finishedmasurenents. The finishedcaps show m TableII.

MENTS

iEAM/ ;’rcll I-tlw shallml s’rcH/

IN

Ifom to

Nlll.

BOB/

I.PR

6-1)2 6-5/8 6-3/4 6-7/8

TableII - Finish@5measurements Head Reightof cap &ight of curtain~/

Size measurements~/ at center~/ frent back inches inches inches inches 6-3/8 20-1/8 / Z=&

2-3/8 2-7/8 2-3/8 2-7/8

4-7/8 2-3/8 2-7/8

7-1/8 7-1/4 7-3/8 7-1/2 7-5/8 7-3/4

Toleranw

20-1/2 20-7/8 21-1/4 21-5/8

&3/8 22-3/4 23-1/8 23-1/2 23-7/8 24-1/4

+1/4 -1/8

4-7/8 4-7/8 4-7/8 4-7/8 4-7/8 4-7/8 4-7/8 4-7/8 4-7/8

2-3/8 2-3/8 2-3/8 2-3/8 2-3/8 2-3/8 2-3/8 2-3/8 2-3/8

2-7/8 2-7/8 2-7/8 2-7/8 2-7/8 2-7/8 2-7/8 2-7/8 2-7/8

+1/$ +1/4 +1/4 -1/8 -1/8 -1/8

1/ Headmeasurementsshallbe takenwitha gage (see6.4).—

~/ 8eightof cap measurementshallbe taken at ~ centerof the cap from the folded edge at the tmttom of ‘rrecumain to the raised edge of the side crown.

3/ Eeightof curtainreasuramentsshallbe takenat tie lccationfor the front ‘d back seams fran the folded tottan~edge to the folded top -edgeof the curtain. L

I

I

1.

1“

I

MILTC-29433(MC).

3.8h!orkmanship.‘l%efinishedcaps shallconformto the qualityof pr@ct establishedby thiss~cification. ‘he occurrenceof defectsshallnot exceed the a~licable acceptablequalitylevel(ML).

4. wALITY AS.SURAN.2EPROVISIONS

4.1 Responsibilityfor ins~ction. unless otherwisesp5cifiedin the contractor pxcha= order,the contractoris responsiblefor the psrformance of all ins%ction requirementsas s~cified herein. Except as otherwise SpeCifid in the contractor purchaseorder,the contractormay use his own or anY other facilitiessuitable for tie perfomce of the insgectiOn requirementsspecified herein, unless diaapprovsdby Government. The Governmentreservesthe rightto ~rform any of the inspectionsset forthin the specificationwhere such inspectionsare deemed necessaryto assure su~lies ad servicesconfmm to prescribedrequirements.

4.1.1Reswnsibilityof canpliance.All itemsmustmeet all requirementsof sections3 and 5. ‘I’heinspectionset forthin thiss~cificationshallteccme a ~rt Of the contractor’soverallins-ion systemor qualityprogram. ‘l’he absenceof any inspectionrequiranentsin the s~cificationshallnot relieve the contractorof the respmsibilityof assuricgthat all prcductsor supplies subnitt.edto the Gcwerrnnentfor acceptanceccxmplywithall reauirernentsof the contract. Samplingin qualityconformancedces not authorizesuhnissionof knowndefectivematerial,eitherifiicatd or actual,nor dces it ccnmitthe Governmentto acceptanceof defectivemsterial. \

4.1.2 Certificateof cempliane. hhen certificatesof canplianceare subnitted,the Gove=iiiintreservesthe right to c@ck test such items to determinethe validityof the certification.

4.2 Classificationof inspections. The inspectionrequirementss~cified hereinare classifid as follows:

1. Firstarticleinspection(see4.3)

2. Quality~nfomance inspection(see 4.5).

4.3 Inspectionconditions. Inspectionshall be in accordancewith provisionsset forthin MIL-.STD-9O1, exceptwhereotherwiseindicate5herein.

4.4 Firatarticle. Wnen firstarticleis requir@, inspectionand testing shallhe made on a completelyfabricatedcap of each classforall provisions of thisspecificationapplicableto end prcductexaminationad tests.

4.5 Qualityconformanceins- ions

4.5.1 Ccmp2nent~ material testing. In accordancewith 4.1 above, c~nents and materlas -l ~ testd in accordancewith all rernrirsments of referenced-if ications,fiquresand standardsunlessotherwiseexcluded, amended,mcdifiedor qualifiedin this s~cificationor applicablepxchase docunent. In addition,testingshall te FErformed on com~nents listedin Table III for characteristicsnOted. All requirements are applicable to the sample unit. AU test reprts shall contain the individualvaluesutilizedin expressing the finalresults.

4.5.2Samplingfor testing. Samplingshallbe in accordancewith MIL-S’ID- 901 exceptfor axqmnents s~cifid @low. The lot shallbe unacceptableif one or more sampleunitsfailto m2et any test requirements~cified herein.

The unit for expressinglot size ad sampleunit for testirqeach ccmpment shallte in accordancewiththe following:

Commnent Lot sizeexpresssdas SampleUnit for‘Ik2sting

Eyelets 1000 15

4.5.3Examinationof the end iten. The end item examinationfor the—— finishedcap shallbe as specifie5in MIGSTE-901.

4.5.4Finishedmeasurements.~ Any measurementdeviatiw fram we nominal dimensionand tolerancespci~ied in ‘EableII, shall be cl=slfld = a measurementdefect.

4.5.5Examinationof packagingreuuirements. The examinationforcompliance with ~ckaging,~cking andmarkingregpiremqtsshall~ as ~cif ied in MIL-

STO-901. I

4.5.6Examinationof pa.lletization;‘?mexaminationshallte made to deter-mine that the @LletizatiOnCanplieswith Section5 requirements.’12efects shallh scorsdin accordancewith the list,below. The sanipleunit shallbe one @letized mit la f~l pre~r~ for ,deliverY.The lot size shallbe the numberof @letized unit loads iq the e@ iteq ips~ction lot. The inspectionlevelshallbe S-1 and the @2L sl@l 6.5‘defects~r hundredunits (13fifJ’s).

Examire Cefect

Finisheddimension kmgth, widthor height me.xim~requirement.

Palletization N& as sgxscified.

exceedsspecified

Containerpatternnot as s~cified.

Interlockingof ,loadsnot as specified.

Jmad not horded ~with required straps as specif id.

Met-king Clnitted;incorrect;illegible;of impropersize, lccation,sequenceor methd of,q@icatiOn.

I .

~ MIIr-C-29433iMC) k..+ a

‘“U+2-29433(MC)

5. PACKAGItW

5.1 Packaginq. PackagingshallIx?levelA or ccmnercialas specified(see 6.2).

5.1.1Level A. Bch cap shallbe placedin an individualpolyethylenebag measurinqa~roximately6 incheswide by 15 incheslong. The @yethylene flexible-fifishallbe‘0.0015inchthick.

5.3).

5.1.2Ccxnnercial. The caps shall k manufacturer’scamnercialpractice.

5.2 Packing. Packingshallbe levelA, 6.2).

5.2.1LevelA.

Fachbag shallcontaina label(see

~ckagd in *CO”.. !_ICt With the

B, or ccnmercialaa sp2cified (see

5.2.1.1Methcd 1. he hundredtwenty-five(125) caps of one size only, packagd as specifiedin 5.1..1,shall be ~cked in a fiberboardshipping containerwith liner conformiqg to class weatherresistant,size No. 2A or MIkB-17757, assembled,closed,and reinforcedas s@cifie3 in the appndix thereto. ‘1’bwardsthe end of the qcmtract,or ken there is less than the requiredSmfJuntof the same SiZe per container,mixed.sizesmay.& pcked withinthe sameshippingcontainer.

5.2.1.2Methcd 2. Men spcified (see 6.2), six level B shipping containers,(750 caps of one size only) shall be tacked in a fiberboard shippingcontainerconformingto class wea~er resistant,size No. 4 of MIL-B-17757, assenbkd, closd, ad reinforcd as s~if is+ in the ap~ndix thereto. !Ibwardsthe end of the contract,or when there is less than the reguired amount p?r containerof the same size,mixed sizesmay & pscked withinthe sareshippingcontainer.

5.2.2Level B. We hundred twenty five (125) caps of one size only, package5as s%cified in 5.1.1, shall be Pcked in a fiberboardahipping containerconformingto classdamestic,sizeNo. 2A of MIPB-17757,SSS*led ad closeAas s~cified in the ap~ndix thereto. Fiberboardusedto fabricate the kxes shallke grade275. lbwardsthe end of the contract,or when there is less than the requiredmount per cuntainerof the same size,mixed sizes may h packedwithinthe sameshippinqcontainer.

5.2.3C-rcial. caps,pwkaged as spscifiedin 5.1, shallbe ~cked in a manner to insure carrier acceptanceand safe delivery at destination.

ContainersMl be in accordancewith UniformClassificationRules,Nstional Motor Freight ClassificationRule and U. S. Fcktal ServicesManual, as a~licable.

MIL-C-29433(MC) “

5.3Markinq. In rdditionto any spscialmarkingrequird by the contractor purchaseorder,the shippingcontainersshallbe markedin accordancewithtie requir~entsof MIL-STD-129.

5.3.1 FcJyethlenebaggedpackages. Fulethylenetaggedpckages shallhave the followingi.nfonnationlegiblyprintedor stanpsdin blackdirectlyon the bag acrossthe centerfaceor on a hhitegapr labelinsertedwithinthe bag so as to prmit readyidentification.‘he bag or label shall indicatethe followinginformation.

STCCKNOMSRR

NMENcIAm

SIZE

COtWRACTNUMSER

NAMEOF CCXWT.AC2Y3R

5.3.2Mixed sizes. Each shippingcontainerpackedwithmixed sizesshall have a 5 X 4 inch v.biteps~r label securelyattachadto the end and side directlyunderthe printingor stenciling.‘he wards “MIXEOSIZES”shallbe plainlystanpxlor printedthereon,ad under these v.wrdsshall lx legibly printed& correctquantityd sizescontainedtherein.

5.4 Palletization.Wen s~cified (see6.2), caps ~cked as Swif ied shall he palletizedon a 4-wayentry@let in accordancewith loadtype‘1Aof MIL- S’ID-147.=ch preparedloadshallbe bondedwithprimaryand secondarystraps in accordancekotiingmsans C,K and L or O or P. Palletpatternshallbe in accordancewith the ap~ndix of MIL-STE-?47. The -let shallbe 4-way,Type 1, Class1, Style1. SizeA, Wed GroupI, II, III,or IV of MI=P-15011, or 4-way,‘IypsXV,V or VIII,Classl,StyleA, Size2, Wcd GroupI, II, III, IV, GradeA of NN-P-71. Interlockingof loadsshallbe effecbxlby reversingthe patternof each course. If the containeris of a sizewhichdoesnot conform to any of the @terns specifiedin MIL-STO-147, the palletpttern usedshall he approved by the contractingofficer.

6. NOTES

6.1 Intendeduse. The caps describedherein are intendedfor wsar by enlistedmale prsomel of the MarineCorps.

6.2 Orderingdata.

6.2.1Acquisitionreouirements. ‘l’heacquisitiondocunentsshoulds~cify the followic.q:

(a) (b) (c) (d) (e)

(f) (g)

Title,nmnberard date of this Spcification.

Classacd sizerequired(see1.2).

Ihetherfirstarticleis requir~ (see3.2).

Numberof caps in firstarticle(see3.2).

Selectionof applicablelevel of psckaging and packing (see 5.1 and 5.2).

}~en levelA, methcd2, packingis required(see5.2.1.2). .

Wnen p.lletizationis required(see5.4).

MIL–C–29433(MC)

6.2.2Data requiranenta.When this s~ification is used in an acquisition axl data are require5 be delivered,the data requirementsiden~ified below shallbe develo~ as specifiedby an 1664) and deliveredin accordancetit-h%F;$roF$~~ZaYA~~Pm~_~~ List (~w) , incorpratd into the contract. Wnen the provisionsof DoD F7sR Supplw?ent,Part 27, SubPart 27.410-6(DD Form 1423)are invokedand the DD Form 1423 is not used, the data specifiedbelow shall ke delivere3by the contractorin accordancewith the,contractor Prchase order r=mir~n~s.

Deliverabledata remird ~ this s~ificatjon are cited in tie f0110wln9 paragraphs.

Paragra@ no. D3tarequiramenta ApplicableDID no. Options

(a)4. Ins&ctionSystemPrcgram DI-R-4803 -.-—- Plan

(b)4.4 FiratArticleIns~ction DI-T-4901 ------ Procedures

(c)4.4 FirstArticleInspection DI-T-4902 --—— Rep3rt

(d)4.5 Production/7+cceptance DI–T-4903 ——- Insgx@zionProcedures

(e)4.5 ProductionInspection DI-T-4904 —--—- Reprts

(Data iten descriptionsrelatedto this specification,and identifiedin section6 will be approvedand listad as such in DoD 5000.19L., Vol. II, AMSDL. Copies of data itam descriptionsrequiredby the contractorsin connectionwith ~cific acquisitionfun~ions shouldte obtainadfrom the Naval Publicationsand pow Center or as directed by the contracting officer.)

6.3 standardsamples. Fbr informationregardirqthe availabilityof a sampleof th and of the standardshadesspecified,addressinauiryto the acquiri~ a~i~!y issuingt$e invitationforbids.

6.4 Gsges. Informationc&erninq tie gagesmay be obtainedUFon re~est tO

* c0iiEF2Etiingofficer.

6.5 Firstarticle. Examinations,test, and approvalshallbe as s~cified by the contractl~officer(see3.2).

6.6 Figures. Figures1 & 2 are furnishedfor informationpurpses only.

To the extentof any inconsistenciesbetweenthe writtens~cificationad the figures,the writtens~cificationshallgovern.

6.7 Subjectterm (keyvmrd)listing

Caps Garrison Men’s

Prepari~ activity:

Navy-Me

ProjectNo. 8405–N015

I N] 1.-:.-29:33(}If.;)

LINING BASIC MATERIAL

‘wEm!!!@ d ‘“

SIDE CROWN TOP CR0Wf4

OPENING OF CROWN

L

(2W!ZW!J =

SECTION A-A

LEFT S!DE

FIGURE1. CAPS,GARRTSC’S: MEN’S,POLYESTER/WOOL(Class 1 Only)

A+

Ab

RIGHT SIDE

TOP CROWN:

OPENING O“FCROWN

SECTION A-A

F16uRE2 CAP, GARRISON, MEN’S:WOOL, ~REEN CLASS 2ANO~ h ib ~:,,