Att_1_-_Specifications.pdf
PDF 178 KB Posted
- Attached to
- PINN LE VEHICLE UPFITS
- Solicitation number
- 140P8424Q0082
About this file
This document is the Specifications for upfitting two 2024 Chevrolet Tahoe SSVs for the National Park Service (NPS) at Pinnacles National Park in California. The Contractor shall provide all equipment, labor, and supplies to complete the work, except for certain government-furnished equipment that must be installed.
The required work includes installing various lighting and electronic equipment, such as lightbars, spotlights, sirens, radios, radar units, and gun locks. The vehicles will be either fully marked patrol vehicles or unmarked patrol vehicles. The Contractor must verify compatibility of all components and follow specific programming requirements. The Contractor shall provide a one-year warranty on all labor. The government anticipates awarding a firm-fixed-price purchase order under a separate solicitation (Solicitation Number 140P8424Q0082) and will evaluate quotations in accordance with simplified acquisition procedures. This opportunity is set aside for small businesses under NAICS code 336320 with a 1,000-employee size standard.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| Sol_140P8424Q0082_Amd_0002.pdf | ||
| Sol_140P8424Q0082_Amd_0001.pdf | ||
| Att_3_-_Full_Text_Provisions.pdf | ||
| Sol_140P8424Q0082.pdf | ||
| Att_2_-_Technical_Info_Form.docx | DOCX document |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
SPECIFICATIONS
UPFIT TWO 2024 CHEVROLET TAHOE SSV’s for
PINNACLES NATIONAL PARK
The National Park Service (NPS) at Pinnacles National Park (PINN) has a requirement for the upfitting of two 2024 Chevrolet Tahoe SSV’s, leased from the General Services Administration
(GSA), for use by NPS Law Enforcement Officers at PINN.
LOCATION OF WORK: Work will be completed at the Contractor’s facility. The vehicles shall be kept in a secure location with controlled access while at the Contractor’s facility. Location of work shall be no longer than a 4‐hour drive time from PINN’s Paicines, California headquarters.
DELIVERY OF VEHICLES: The vehicles will be shuttled to/from the Contractor’s facility by NPS staff, or the Contractor may choose to arrange transport of the vehicles to the work site.
SUMMARY OF WORK: The Contractor shall provide all equipment, labor, and supplies, unless otherwise noted, to successfully complete the work resulting in fully functional turn‐key law enforcement patrol vehicles.
DESCRIPTION OF WORK:
VEHICLE 1 ‐ Fully Marked Patrol Vehicle with Lightbar
GOVERNMENT‐FURNISHED/CONTRACTOR‐INSTALLED EQUIPMENT:
The Contractor shall install/reuse the following government‐furnished equipment. The
Contractor shall verify dimensions, capabilities, and compatibilities of government‐furnished equipment. If an item cannot be reused, the Contractor shall contact the CO prior to purchasing replacements.
1. Bendix King KNG‐M150 Radio and other radio components
a. Location: center console
2. Bendix King radio speaker.
a. Location : center console mounted low out of the way.
3. Police radar unit with front and rear antennas (Kustom Raptor w/ K‐band antennas).
Dash Mount hardware included. Antenna mounts will need to be acquired by
Contractor. Factory power plug will be used and not hard wired into vehicle.
a. Location: Front antenna hard mounted to driver side front pillar. Rear antenna hard mounted on driver side rear pillar. Counter unit mounted on top center of dash.
4. Cell phone booster
a. Location: External antenna installed on right rear roof of vehicle, booster in manufacturer’s recommended location, Cell phone cradle installed either on center console or appropriate area of dash.
VEHICLE 1 ‐ CONTRACTOR FURNISHED & INSTALLED EQUIPMENT:
The Contractor is responsible for the verification of all quantities, dimensions, capabilities, and compatibilities affecting the work of this contract before ordering products and shall purchase and install the following items. All lighting products should be Whelen or approved equal.
1. Low profile lightbar with Red/Blue/White/Amber fully populated. Red/blue all around with front white takedowns/scene lighting and right and left alley lights. Rear amber traffic advisor. Lightbar programmed to California state specifications for emergency vehicles (one solid red forward facing light, others flashing)
a. Location: Roof mount: manufactures specifications.
b. Quantity: One
2. LED under mirror light. Blue/White and Red/White
a. Location: Under mirrors on driver and passenger side
b. Quantity: One red/white on driver mirror, one blue/white on passenger mirror
3. Whelen Arges Remote spotlight, or approved equal, with mounting kit for 2024
Chevrolet Tahoe and interior control pad.
a. Location: Driver side front quarter panel per manufacturer specifications
b. Quantity: One
4. Head Light Flashers
a. Location: Front Headlights
b. Quantity: One set
5. Taillight Flashers
a. Location: Rear Taillights
b. Quantity: One Set
6. LED side window lights. Red/Blue combo
a. Location: Driver & Passenger side rear cargo area windows‐ centered on the interior bottom window trim
b. Quantity: Two
7. LED license plate lights. Red and Blue
a. Location: On sides of license plate bracket
b. Quantity: One of each color
8. LED flush mount 1‐inch diameter lights. Red and Blue
a. Location: Rear bumper facia, spaced equally driver and passenger side
b. Quantity: One of each color
9. 100‐watt Siren Speaker
a. Location: Mounted in industry standard position/ push bumper.
b. Quantity: One
10. Siren and Light Control with PA (Rotary siren knob)
a. Location: Center console
b. Quantity: One
11. Universal LED dome light, 6‐inch round, with red LED night light, white lens, and white
LED light
a. Location: On ceiling of cab in between front driver and passenger seats
b. Quantity: One
12. Voltage monitor with timer‐or similar.
a. Location: Hard mounted in an accessible area near or attached to the center console or engine compartment.
13. Master cut off switch
a. Location: Mounted concealed to front of center console to shut off all center console electronic components
14. ¼ wave VHF antenna for 152‐162 MHz, 150‐Watt
a. Location: Mounted behind lightbar
b. Quantity: One
c. Antenna cable with NMO Mount to install the antenna
15. ALL new wiring, fuses, circuit breakers, brackets, and associated materials for all electronic wiring. Wire loom shall cover all exposed wiring or wiring in areas that may get damaged.
16. All mounts and brackets required for installation
17. Troy Center Console, CC‐21TH‐1012‐OS, or approved equal,. 22‐inch wide body console with open storage, or best fit with Bendix King KNG‐150M bracket, siren/light controller bracket, Whelen Arges control head bracket, 12v Power Outlet (three), USB power outlet, 4‐inch interior dual cupholder, 3‐inch shallow tray, Two mic holders, and side mount armrest. Unit should include appropriate floorplate.
a. Location: In between driver and passenger seat
18. Magnetic Mic Kit
a. Location: One on driver side of the center console, one on passenger side of center console, both mounted on console mic holders.
b. Quantity: Two
19. Setina, or approved equal, Push Bumper, Lighted (four lights‐ two in front crossmember, one on each side)
a. Location: Front bumper area
b. Quantity: One
20. Setina, or approved equal, single prisoner coated poly partition cage system for a full stock seat
a. Location: Prisoner compartment will be mounted on the passenger side of the vehicle.
b. Quantity: One
21. Setina, or approved equal, TPO door cover for existing door panel
a. Location: passenger side rear door
b. Quantity: One
22. Setina, or approved equal, Rear Cargo Partition, expanded metal
a. Location: Behind rear seat
b. Quantity: One
23. Setina, or approved equal, free standing mounting kit
a. Location: Forward facing between front seats as far forward as possible for driver to access weapons
b. Quantity: One
24. Setina, or approved equal, electronic firearms mounting system with one vault lock for
AR‐15 rifle and one small lock for Remington 870 shotgun mount with #2 key override.
a. Location: Forward facing between front seats as far forward as possible for driver to access weapons
b. Quantity: One
The Contractor shall purchase and install the following items from 8six8one Designs.
https://www.8681designs.com/graphicsstore
(415) 233‐1128
1. NPS LE Vehicle graphics package for 2024 Chevrolet Tahoe.
a. Shall include striping, and assorted stickers and lettering to be placed in accordance with instructions provided.
b. Any factory lettering shall be removed to accommodate NPS graphics.
c. Any deviation required to fit graphics onto vehicle shall be done in consultation with NPS representative.
Example of NPS Large Graphics Package installed on a 2020 Chevrolet Tahoe
VEHICLE 2: Unmarked Patrol Vehicle with Interior Lightbar
GOVERNMENT‐FURNISHED/CONTRACTOR‐INSTALLED EQUIPMENT:
The Contractor shall install/reuse the following government‐furnished equipment. The
Contractor shall verify dimensions, capabilities, and compatibilities of government‐furnished equipment. If an item cannot be reused, the Contractor shall contact the CO prior to purchasing replacements.
1. Bendix King KNG‐M150R Radio and other radio components
b. Location: Remote control head‐ center console. Radio brain‐ manufacturer’s suggested location.
2. Bendix King radio speaker.
a. Location : center console mounted low out of the way.
3. Police radar unit with front and rear antennas (Kustom Raptor w/ K‐band antennas).
Dash Mount hardware included. Antenna mounts will need to be acquired. Factory power plug will be used and not hard wired into vehicle.
a. Location: Front antenna hard mounted to driver side front pillar. Rear antenna hard mounted on driver side rear pillar. Counter unit mounted on top center of dash.
4. Cell phone booster
a. Location: External antenna installed on right rear roof of vehicle, booster in manufacturer’s recommended location, Cell phone cradle installed either on center console or appropriate area of dash.
5. Setina rear cargo box and equipment tray
a. Location: Rear cargo area, immediately behind rear cargo screen.
VEHICLE 2 ‐ CONTRACTOR FURNISHED & INSTALLED EQUIPMENT:
The Contractor is responsible for the verification of all quantities, dimensions, capabilities, and compatibilities affecting the work of this contract before ordering products and shall purchase and install the following items. All lighting products should be Whelen or approved equal.
1. Inner Edge interior front facing lightbar. Two‐piece unit with individual driver and passenger side units. Red driver side, blue passenger side with two LED white flashing/takedowns. Lightbar programmed to California state specifications for emergency vehicles (one solid red forward facing light, others flashing)
a. Location: Front visor mount, manufacturer’s specifications.
b. Quantity: One
2. LED under mirror light. Blue/White and Red/White. Programmed to function as solid white alley light when alley light button is pressed.
a. Location: Under mirrors on driver and passenger side
b. Quantity: One red/white on driver’s mirror, one blue/white on passenger’s mirror
3. Whelen Arges Remote spotlight, or approved equal, with mounting kit for 2024
Chevrolet Tahoe and interior control pad.
a. Location: Driver side front quarter panel per manufacturer specifications
b. Quantity: One
4. Head Light Flashers
a. Location: Front Headlights
b. Quantity: One set
5. Taillight Flashers
a. Location: Rear Taillights
b. Quantity: One Set
6. LED side window lights. Red/Blue/White combo. Programmed to function as alley light when alley light button is pressed.
a. Location: Driver & Passenger side rear cargo area windows‐ centered on the interior bottom window trim
b. Quantity: Two
7. Whelen Outer Edge, or approved equal, rear facing lightbar, two individual units with three OEI2 lightheads each. Red/Yellow on driver side, Blue/Yellow on passenger side.
Programmed to function as traffic advisor as needed.
a. Location: Rear spoiler
b. Quantity: One
8. LED license plate lights. Red and Blue
a. Location: On sides of license plate bracket
b. Quantity: One of each color
9. LED flush mount 1‐inch diameter lights. Red and Blue
a. Location: Rear bumper facia, spaced equally driver and passenger side
b. Quantity: One of each color
10. 100 watt Siren Speaker
a. Location: Mounted in industry standard position/ push bumper.
b. Quantity: One
11. Siren and Light Control with PA (Rotary siren knob)
a. Location: Center console
b. Quantity: One
12. Universal LED dome light, 6‐inch round, with red LED night light, white lens and white
LED light
a. Location: On ceiling of cab in between front driver and passenger seats
b. Quantity: One
13. Voltage monitor with timer‐or similar.
a. Location: Hard mounted in an accessible area near or attached to the center console or engine compartment.
14. Master cut off switch
a. Location: Mounted concealed to front of center console to shut off all center console electronic components
15. ¼ wave VHF antenna for 152‐162 MHz, 150‐Watt
a. Location: Mounted behind lightbar
b. Quantity: One
c. Antenna cable with NMO Mount to install the antenna
16. ALL new wiring, fuses, circuit breakers, brackets, and associated materials for all electronic wiring. Wire loom shall cover all exposed wiring or wiring in areas that may get damaged.
17. All mounts and brackets required for installation
18. Troy Center Console, CC‐21TH‐1012‐OS, or approved equal. 22‐inch wide body console with open storage, or best fit with Bendix King KNG‐150M bracket, siren/light controller bracket, Whelen Arges control head bracket, 12v Power Outlet (three), USB power outlet, 4‐inch interior dual cupholder, 3‐inch shallow tray, two mic holders, and side mount armrest. Unit should include appropriate floorplate.
a. Location: In between driver and passenger seat
19. Magnetic Mic Kit
a. Location: One on driver side of the center console, one on passenger side of center console, both mounted on console mic holders.
b. Quantity: Two
20. Setina, or approved equal, Push Bumper, Lighted (4 lights ‐ two in front crossmember, one on each side)
a. Location: Front bumper area
b. Quantity: One
21. Setina, or approved equal, single prisoner coated poly partition cage system for a full stock seat
a. Location: Prisoner compartment will be mounted on the passenger side of the vehicle.
b. Quantity: One
22. Setina, or approved equal, TPO door cover for existing door panel
a. Location: passenger side rear door
b. Quantity: One
23. Setina, or approved equal, Rear Cargo Partition, expanded metal
a. Location: Behind rear seat
b. Quantity: One
24. Setina, or approved equal, free standing mounting kit
a. Location: Forward facing between front seats as far forward as possible for driver to access weapons
b. Quantity: One
25. Setina, or approved equal, electronic firearms mounting system with one vault lock for
AR‐15 rifle and one small lock for Remington 870 shotgun mount with #2 key override.
a. Location: Forward facing between front seats as far forward as possible for driver to access weapons
b. Quantity: One
PROGRAMING NOTES FOR LIGHTS AND ACCESSORIES
Programing Notes for police lights
1. All lights shall be programmed through the Siren and Light Controller with directional controls to the industry standard. Light position 1: All rear facing lights flash. Position 2:
All rear and forward‐facing lights flash‐NO wigwag or takedowns. Position 3: All lights active with sirens and takedowns and wigwags (if possible).
2. Programing Notes for accessories
a. The Siren and Light Controller should function as a switch for all accessories, i.e., gun locks, power port for radio unit.
b. We request a “master” cut off switch mounted concealed under the center console, to shut off weapons lock system.
INSPECTION AND ACCEPTANCE: The Contractor shall demonstrate full functionality of all equipment upon completion of vehicle. Equipment will be tested to ensure proper workmanship prior to final acceptance of vehicle by NPS.
WARRANTY: The Contractor shall provide a one year warranty on all labor. If installed equipment malfunctions within a year of completion the Contractor shall in a timely manner assess the malfunction to determine if there was faulty labor or equipment. If labor is found to be at fault the Contractor shall fix or replace the equipment at no cost to the government. If the equipment is found to be at fault the Contractor shall supply a quote to obtain and replace the faulty equipment and replace under factory warranty if applicable. The government reserves the right to obtain a second opinion.
File details come from the government source that posted it. Updated .