DIAGRAMS.pdf

County Road 114

Co un ty R oa d

23W 23E 24W 24E

Fe nc e

Fe nc e w es t

Fence 3 Fence 4

Fe nc e ea st

Fence 1 – Divide sections 23W and 23E

N

2P H

2P H

2P H

HI

2P H

P P gate gate

P* tank cattle guard

From North:

2PH = construct 2 post H-brace on south side of cattle guard 2PH = construct 2 post H-brace on north side of existing corrals 2PH = construct 2 post H-brace on south side of existing corrals P = set 10’ post at ¼ mile HI = construct 2 post H-brace at ½ mile P = set 10’ post at ¾ mile 2PH = construct 2 post H-brace with 16’ gate opening P* = set 10’ post to tie gate (see fence 3)

County Road 114 fence 3 fence 3 corrals

Fence 2 west and east – Grazing Strip easement between 23E and 24W gate gate gate gate

2P H

2P H

2P H

2P H

2P H

2P H

2P H

2P H cattle guards

P* P*

P

P P

P fence 3 fence 4

N From North (Fence 2 west):

2PH = construct 2 post H-brace with gate P = set 10’ post at ¼ mile 2PH = construct 2 post H-brace at north end of cattle guard 2PH = construct 2 post H-brace at south end of cattle guard HI = construct 2 post H-brace at ½ mile P = set 10’ post at ¾ mile 2PH = construct 2 post H-brace with gate tying to post set at end of fence 3

From North (Fence 2 east):

Repeat as above tying to post set at end of fence 4 2/ m ile

1/ m ile

Fence 3 – Along County Road 114 south side of section 23

N fe nc e w es t fe nc e

P* P P

P* 2PH 2PH 2PH 2PH ga te ga

From West:

2PH = construct 2 post H-brace in corner P = set 10’ post at ¼ mile 2PH = construct 2 post H-brace with gate to close at south end of fence 1 P* = set 10’ post to tie gates (also used for gate at south end of fence 1) 2PH = construct 2 post H-brace with gate to close at south end of fence 1 P = set 10’ post at ¾ mile 2PH = construct 2 post H-brace with gate to close at south end of fence 2 west P* = set 10’ post to tie gates (also used for gate at south end of fence 2 west) fe nc e

Fence 4 – along County Road 114 south side of section 24

P* P P

2PH 2PH 2PH Hex gate fe nc e fe nc e w es t ca tt le g ua rd

2PH

Co un ty R oa d

N

From West:

P* = set 10’ post to tie gates (also used for gate at south end of fence 2 east) 2PH = construct 2 post H-brace with gate at west end of cattle guard 2PH = construct 2 post H-brace at east end of cattle guard P = set 10’ post at ¼ mile 2PH = construct 2 post H-brace with gate to close in line with gate at south end of existing fence 2PH = construct 2 post H-brace with gate at south end of existing fence P = set 10’ post at ¾ mile Hex = tie fence to existing corner H-brace

Terminal H-brace, note screw in anchor dead-man

2PH on diagrams

In-line H-brace, note 2 dead-men and wire tied to far posts In-line 10’ post with wire tied off

P on diagrams HI on diagrams

In-line double terminal brace assembly for 16’ gate Opening large enough for gate to swing fully through

2PH with gate on diagrams

Steel post driven deep to hold fence down in low area

Line post - note staples loosely hold wire

Other features