Attach_3_Spec_417_G_Shackles_and_Swivels.pdf

UNITED STATES COAST GUARD

SHORE INFRASTRUCTURE LOGISITICS CENTER

WATERWAYS OPERATIONS PRODUCT LINE

APRIL 2018

SPECIFICATION FOR FABRICATION

OF

SHACKLES, MODEER SHACKLES, AND SWIVELS

SPECIFICATION NO. 417

REVISION G

Attachment 3

WORK ITEM 1: 4030-00-236-8403, 121079 Shackle ASSY SPLTKEY 1st

Class, Purchase

WORK ITEM 2: 4030-00-236-8402, 121079 Shackle ASSY SPLTKEY 2nd Class, Purchase

WORK ITEM 3: 4030-01-286-6205, 121079 Shackle ASSY SPLTKEY 3rd Class, Purchase

WORK ITEM 4: 4030-01-286-6204, 121079 Shackle ASSY SPLTKEY 4th Class, Purchase

WORK ITEM 5: 4030-00-527-8871, 121079 Shackle ASSY SPLTKEY SPEC Class, Purchase

WORK ITEM 6: 4030-00-267-7077, 121079 Shackle ASSY Rivet Pin 1st Class, Purchase

WORK ITEM 7: 4030-00-290-4092, 121079 Shackle ASSY Rivet Pin 2nd Class, Purchase

WORK ITEM 8: 4030-00-240-4717, 121079 Shackle ASSY Rivet Pin 3rd Class, Purchase

WORK ITEM 9: 4030-00-729-6093, 121079 Shackle ASSY Rivet Pin 4th Class, Purchase

WORK ITEM 10: 4030-01-042-9069, 121080 Shackle ASSY MODEER 1st Class, Purchase

WORK ITEM 11: 4030-01-042-9070, 121080 Shackle ASSY MODEER 2nd Class, Purchase

WORK ITEM 12: 5315-00-300-0370, 121079 Pin Split Key 1st Class, Purchase

WORK ITEM 13: 5315-00-300-0369, 121079 Pin Split Key 2nd Class, Purchase

WORK ITEM 14: 5315-00-300-0368, 121079 Pin Split Key 3rd Class, Purchase

WORK ITEM 15: 5315-00-300-0367, 121079 Pin Split Key 4th Class, WORK ITEM 16: 5315-00-300-0374, 121079 Pin Rivet 1st Class, Purchase

WORK ITEM 17: 5315-00-300-0373, 121079 Pin Rivet 2nd Class, Purchase

WORK ITEM 18: 5315-00-300-0372, 121079 Pin Rivet 3rd Class, Purchase

WORK ITEM 19: 5315-00-300-0371, 121079 Pin Rivet 4th Class, Purchase

WORK ITEM 20: 5315-00-161-4607, 121079 Key Split STNLS 1, 2 & 3rd Class, Purchase

WORK ITEM 21: 5315-00-161-4612, 121079 Key Split STNLS 4TH Class, Purchase

WORK ITEM 22: 5315-00-148-2905, 121079 Key Split STNLS SP Class, Purchase

WORK ITEM 23: 4030-00-729-6089, 121081 Swivel 2 inch 1st Class, Purchase

WORK ITEM 24: 4030-00-729-6090, 121081 Swivel 1 ¾ inch 2nd Class, Purchase

WORK ITEM 25: 4030-00-729-6091, 121081 Swivel 1 ½ inch 3rd Class, Purchase

WORK ITEM 26: 4030-00-729-6094, 121081 Swivel 1 ¼ inch 4th Class,

1. SCOPE

1.1 Intent. This specification describes the requirements for the Manufacturing, Testing, Inspection, Packaging, and Marking of shackle assemblies, shackle pins, swivels, and split keys used as mooring fittings on aids to navigation buoys. Also included herein are the requirements for Modeer shackle assemblies used for handling stud link chain.

NSN: 4030-00-236-8403, P/N: 121079 Shackle ASSY SPLTKEY 1st Class NSN: 4030-00-236-8402, P/N: 121079 Shackle ASSY SPLTKEY 2nd Class NSN: 4030-01-286-6205, P/N: 121079 Shackle ASSY SPLTKEY 3RD Class NSN: 4030-01-286-6204, P/N: 121079 Shackle ASSY SPLTKEY 4th Class NSN: 4030-00-527-8871, P/N: 121079 Shackle ASSY SPLTKEY SPEC Class NSN: 4030-00-267-7077, P/N: 121079 Shackle ASSY Rivet Pin 1st Class NSN: 4030-00-290-4092, P/N: 121079 Shackle ASSY Rivet Pin 2nd Class NSN: 4030-00-240-4717, P/N: 121079 Shackle ASSY Rivet Pin 3rd Class NSN: 4030-00-729-6093, P/N: 121079 Shackle ASSY Rivet Pin 4th Class NSN: 4030-01-042-9069, P/N: 121080 Shackle ASSY MODEER 1st Class NSN: 4030-01-042-9070, P/N: 121080 Shackle ASSY MODEER 2nd Class NSN: 5315-00-300-0370, P/N: 121079 Pin Split Key 1st Class NSN: 5315-00-300-0369, P/N: 121079 Pin Split Key 2nd Class NSN: 5315-00-300-0368, P/N: 121079 Pin Split Key 3rd Class NSN: 5315-00-300-0367, P/N: 121079 Pin Split Key 4th Class NSN: 5315-00-300-0374, P/N: 121079 Pin Rivet 1st Class NSN: 5315-00-300-0373, P/N: 121079 Pin Rivet 2nd Class NSN: 5315-00-300-0372, P/N: 121079 Pin Rivet 3rd Class NSN: 5315-00-300-0371, P/N: 121079 Pin Rivet 4th Class NSN: 5315-00-161-4607, P/N: 121079 Key Split STNLS 1, 2 & 3rd Class NSN: 5315-00-161-4612, P/N: 121079 Key Split STNLS 4th Class NSN: 5315-00-148-2905, P/N: 121079 Key Split STNLS SP Class NSN: 4030-00-729-6089, P/N: 121081 Swivel 2 inch 1st Class NSN: 4030-00-729-6090, P/N: 121081 Swivel 1 ¾ inch 2nd Class NSN: 4030-00-729-6091, P/N: 121081 Swivel 1 ½ inch 3rd Class NSN: 4030-00-729-6094, P/N: 121081 Swivel 1 ¼ inch 4th Class

1.2 Government-Furnished Property.

None

1.3 Classification. Items covered by this specification are described by class, type, and style as defined below.

1.3.1 Class. Shackle assemblies, shackle pins, Modeer shackle assemblies, and swivels are of the classes listed below. The class of an item is based on the item’s size, which is defined as the nominal diameter of the bar stock used in the manufacture of the item. In addition, a split key is considered to be of the same class as the shackle pin with which it mates.

Class Shackle Size

(in.)

Modeer Shackle

Size (in.)

Swivel Size

(in.)

1st 2 1-3/4 2 2nd 1-3/4 1-5/8 1-3/4 3rd 1-1/2 - 1-1/2 4th 1 - 1-1/4

Special 2-1/2 - -

1.3.2 Type. The term “type” refers to shackle pins. Two types of shackle pin are covered by this specification: rivet pin and split key pin.

1.3.3 Style. The term “style” refers to swivels. Two styles of swivel are covered by this specification:

upset head and threaded nut.

1.4 Definitions.

1.4.1 Batch. A batch consists of all items of the same class, type, and style, made from the same heat of steel, and submitted for inspection at the same time.

2. REFERENCES

COAST GUARD DRAWINGS

Coast Guard Drawing 121079 Rev D, Shackles (Rivet Pin & Split Key) Coast Guard Drawing 121080 Rev C, Modeer Shackles Coast Guard Drawing 121081 Rev C, Swivels (Upset Head and Threaded Nut Styles)

COAST GUARD PUBLICATIONS

None

OTHER REFERENCES

ANSI/ASQ Q9001, 1 Oct 2015 Quality Management Systems – Requirements – T860E ASTM A666-15, 1 Mar 2015 Standard Specification for Annealed or Cold-Worked

Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar ANSI/ASQ Z1.4-2008, R2013 Sampling Procedures and Table for Inspection by Attributes

(Table IIA, based on General Inspection Level II from Table I) ANSI/NCSL Z540-3.2006 Requirements for the Calibration of Measuring and Test Equipment MIL-STD-2073-1E Change 1, 7 Jan 2011 Standard Practice for Military Packaging

ASTM D5168-12, 1 May 2012 Standard Practice for Fabrication and Closure of Triple-Wall Corrugated Fiberboard Containers1

MIL-STD-129R, 18 Feb 2014 Military Marking for Shipment and Storage ISO/IEC 16388-2007, May 15 2007 Information technology - Automatic identification and data capture techniques - Code 39 bar code symbology specification

2.1 General. The documents listed in this section are referenced in sections 3 and 4 of this specification.

This section does not include documents cited in other sections of this specification, which are recommended for additional information or used as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements cited in sections 3 and 4 of this specification, whether or not the referenced documents are listed here.

Suffixes denoting the specific issue of each document are omitted from future references to the documents in this specification.

2.2 Drawings. The latest revision of the United States Coast Guard Ocean Engineering drawings form a part of this specification to the extent referenced herein and shall be referred to as "the drawing" throughout this specification.

2.3 Other references. The above documents form a part of this specification to the extent referenced herein.

2.4 Specification order of precedence. In the event of a conflict between the text of this specification and the references cited herein, this specification shall take precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

3. REQUIREMENTS

3.1 General. Shackle bodies and pins, Modeer shackle bodies and pins, and swivels shall be manufactured of carbon steel, and shall be either forged or cast. Split keys shall be manufactured of corrosion resistant steel. The slot in the split key pin shall have a rounded slot or rectangular shape.

3.1.1 Batch Number. The Contractor shall assign a unique sequential number to each batch submitted under this specification.

3.1.2 Assemblies. Swivels shall be furnished assembled, as shown on the drawings. Shackle assemblies shall consist of shackle components furnished assembled as described below, in the manner shown on the drawings.

3.1.2.1 Rivet Pin Shackle Assembly. A rivet pin shackle assembly shall consist of the specified class of shackle body and the identical class of rivet pin, assembled. In addition, a retaining wire shall be inserted through the 3/16-inch hole in the rivet pin, so that the pin will remain with the shackle body during shipment.

3.1.2.2 Split Key Shackle Assembly. A split key shackle assembly shall consist of the specified class of shackle body, the identical class of split key pin, and the identical class of split key, assembled. The legs of the split key shall not be spread more than 5 degrees after the split key has been inserted in the pin.

3.1.2.3 Modeer Shackle Assembly. A Modeer shackle assembly shall consist of the specified class of Modeer shackle body and the identical class of Modeer shackle pin, assembled.

3.2 Material.

3.2.1 Shackle Bodies. Shackle Pins, Swivels. Shackle bodies and pins, Modeer shackle bodies and pins, and swivels shall be made of carbon steel of uniform quality. The chemical composition of the steel shall be determined at the steel mill for each heat of steel, and shall conform to the values listed in Table I.

Table I Chemical Composition of Steel

Element Wt. Percent Carbon 0.28 - 0.55

Manganese 0.60 - 1.00 Silicon 0.80 max.

Phosphorus 0.05 max.

Sulphur 0.05 max.

3.2.1.1 Alloying Elements. Additional alloying elements may be added to the steel as necessary to meet the proof load and breaking load requirements specified herein. If alloying elements are added, they shall not exceed the values listed in Table II.

Table II Alloying Elements

Element Wt. Percent Chromium 0.6 max.

Nickel 0.7 max.

Molybdenum 0.25 max.

3.2.2 Split Keys. Split keys shall be class 316 or class 316L plate or strip corrosion resistant steel conforming to ASTM A666.

3.2.3 Traceability. The Contractor shall maintain the traceability of steel and corrosion resistant steel throughout the production, inspection, and testing processes. Each item offered under this specification shall be traceable by batch number to the heat of steel or corrosion resistant steel from which it was made.

3.3 Design. Items covered by this specification shall conform to the configurations, dimensions, and tolerances shown on the drawings. Swivels shall rotate freely and may be furnished as either the upset head style or the threaded nut style as shown on the drawing. Shackles shall be easily assembled and disassembled. When rivet pins are furnished alone, and not as part of rivet pin shackle assemblies, the 3/16-inch hole shown on the drawings may be omitted.

3.4 Proof Load. Each shackle assembly, shackle pin, Modeer shackle assembly, and swivel offered for acceptance shall have been subjected to the applicable proof load specified in Table III without rupture or deformation.

3.5 Breaking Load. Shackle assemblies, shackle pins, Modeer shackle assemblies, and swivels shall be capable of withstanding the applicable breaking load specified in Table III for a minimum of 15 seconds without rupture.

Table III Proof and Breaking Loads

Item Proof Load

(lbs.)

Breaking Load

(lbs.)

Shackle Assemblies and Shackle Pins

1st Class 115,000 230,000 2nd Class 90,000 180,000 3rd Class 65,000 130,000 4th Class 30,000 60,000

Special Class 180,000 360,000

Modeer Shackle Assemblies

1st Class 90,000 180,000 2nd Class 65,000 130,000

Swivels 1st Class 82,000 164,000 2nd Class 60,000 120,000 3rd Class 45,000 90,000 4th Class 30,000 60,000

3.6 Heat Treatment. Items submitted under this specification shall be heat treated by a suitable process as required to meet the proof load and breaking load requirements specified herein.

3.7 Welding. Welding is required in the design of the threaded nut style swivel, as shown on the drawings. This welding shall be performed by an electric welding method. The welds shall not contain cracks, craters, undercutting, overlap, porosity, or lack of fusion.

3.8 Finish. All items shall be submitted in natural color and finish. Varnish or other coatings shall not be used.

3.9 Surfaces. All items offered shall be free from cracks, mill defects, burrs, flaws, rough surfaces, or other defects which might adversely affect their serviceability and handling.

3.10 Identification Marking. For tracking purposes, each item offered under this specification (with the exception of split keys) shall be identified by an identification marking. The marking shall be stamped, engraved, or otherwise permanently affixed to each item, and shall include the manufacturer’s name or trademark, the batch number, and the year code and last three digits of the contract number (for example, a contract numbered “HSCG40-XX-P-TCB018” would be marked as (“XX-018”). Shackle assemblies and Modeer shackle assemblies shall be marked on the bodies and on the pins.

3.11 Documentation.

3.11.1 Quality Assurance Inspection Form. The Contractor shall develop and provide a Quality Assurance Inspection Form (QAIF). The QAIF shall be used to document the inspections and tests performed during the fabrication process. The form shall be printed on standard (i.e., 8½ x 11 inch) white paper. Inspection results may be handwritten on the form. The form shall be prepared in the Contractor's format and shall be legible, in English, and suitable for reproduction. The form shall be made available to the Contracting Officer’s Representative (COR) for review.

3.11.1.1 QAIF Content. At a minimum the QAIF shall include:

Item Batch number (paragraph 3.1.1) Serial numbers of items inspected Date of test or inspection Test or inspection to be performed (list every test and inspection required by paragraph 4.5) Result of test or inspection Accept/Reject criteria for each test or inspection Corrective action taken (if any) Notes Initials or signatures of Contractor’s test personnel

3.11.2 Mill Reports. The Contractor shall furnish a mill report from the steel mill for each heat of steel.

The report shall indicate the heat number, steel designation, chemical composition (including any added alloying elements), and quantity of steel represented by the report. Mill reports containing the above information shall also be furnished for each heat of corrosion resistant steel used in split keys.

3.11.3 Material Inspection and Receiving Report (DHS Form 700-21). A form DHS-700-21 shall be used as a certification of product quality assurance, as a packing list, and as a certification of acceptance. The Contractor shall prepare a separate DHS-700-21 for each shipping lot. Prior to shipment, the DHS-700-21 must be signed by the COR.

4. QUALITY ASSURANCE

4.1 General. The Contractor's quality assurance program shall meet the requirements of ASQ Q9001.

However, the Contractor does not have to be ASQ Q9001 certified.

4.1.1 Contractor’s calibration system. The contractor shall maintain a calibration and maintenance system to control the accuracy of measurement and test equipment used in the fulfillment of this specification.

The system shall include, as a minimum, prescribed calibration intervals and the source of calibration. A monitoring system to this requirement shall be readily available to the Coast Guard Inspector. Calibration shall be traceable to the National Institute of Standards and Technology.

4.2 Classification of Inspections. The inspection requirements specified herein are classified as follows:

Contractor production inspection (paragraph 4.2.1) Coast Guard inspection (paragraph 4.2.2)

4.2.1 Contractor Production Inspection. The tests and inspections required by this specification are not intended to supplant any controls, examinations, inspections, or tests normally employed by the Contractor to assure product quality. The Contractor shall perform the tests and inspections specified in paragraph 4.5 to ensure conformance to this specification. The Contractor shall provide space, personnel, and test equipment to conduct all inspection and test requirements.

4.2.2 Coast Guard Inspection. The Coast Guard reserves the right to observe, verify, or perform the tests and inspections outlined in paragraph 4.5. During the Coast Guard inspection, the COR will use the defect categories, rejection criteria, and sampling plans outlined in paragraphs 4.3 and 4.4 (and all associated sub-paragraphs).

4.3 Defect categories. The defect categories listed below will be used during the Coast Guard inspection.

4.3.1 Major. Failure to comply with the requirements of the following paragraphs will constitute major defects:

3.2 Material (and all associated subparagraphs)

3.4 Proof load

3.5 Breaking load

4.3.1.1 Rejection for major defects. If a major defect is found in any batch, the entire batch will be rejected. A batch thus rejected shall not be reworked or resubmitted.

4.3.2 Minor. Failure to comply with the requirements of the following paragraphs will constitute minor defects:

3.3 Design

3.7 Welding

3.8 Finish

3.9 Surfaces

3.10 Marking

4.3.2.1 Rejection for minor defects. Batches rejected for minor defects may be reworked and resubmitted for inspection when they are in compliance with the requirements of this specification. Resubmitted batches shall be clearly identified as such and shall be kept separate from new batches.

4.4 Sampling. Samples for inspections and tests performed during the Coast Guard inspection will be randomly selected from batches by the COR, according to the sampling plans described below.

4.4.1 Sampling plan for inspection of minor defects. The unit of inspection will be one shackle assembly, one shackle pin, one Modeer shackle assembly, one swivel, or one split key. The number of samples and accept/reject values will be in accordance with Table IV.

Table IV Sampling for Minor Defects

No. Items In Batch

No. of Samples

Minor Defects Accept Reject

2 to 15 2 0 1 16 to 50 5 1 2 51 to 90 8 2 3 91 to 150 13 3 4

151 to 280 20 5 6 281 to 500 32 7 8 501 to 1200 50 10 11

1201 to 3200 80 14 15 3201 and above 125 21 22

4.4.2 Sampling plan for proof load and breaking load tests. The unit of inspection will be one shackle assembly, one shackle pin, one Modeer shackle assembly, or one swivel. The number of samples and accept/reject values will be in accordance with Table V. In addition to the deliverables required by the solicitation, additional units shall be manufactured and processed with each batch in the quantities required by Table V for the breaking load tests.

Table V Proof Load and Breaking Load

No. Items in Batch

Proof Load Breaking Load No.

Samples Accept Reject No.

Samples Accept Reject

2 to 15 2 0 1 2 0 1 16 to 50 5 0 1 2 0 1 51 to 90 8 0 1 2 0 1 9l to l50 13 0 1 3 0 1 151 to 280 20 0 1 3 0 1 281 to 500 32 0 1 3 0 1 501 to 1200 50 0 1 4 0 1

1201 to 3200 80 0 1 4 0 1 3201 and above 125 0 1 4 0 1

4.5 Inspections and tests.

4.5.1 General. The following inspections and tests shall be performed to comply with the requirements of this specification. They are not intended to limit or supplant any inspections and tests normally performed by the Contractor.

4.5.2 Documentation Review. The documentation required by paragraph 3.11 shall be reviewed for conformance with this specification and provided to the COR upon request.

4.5.3 Visual inspection. Each item shall be visually inspected to verify conformance with paragraphs 3.3, 3.7, 3.8, 3.9, and 3.10. Items failing to comply with the requirements of this specification shall be rejected.

4.5.3.1 Proof load test. The Contractor shall proof test each shackle assembly, shackle pin, Modeer shackle assembly, and swivel manufactured under this specification. Items which fail this proof testing prior to being offered for Coast Guard inspection may be reworked, or screened for defectives, and re-tested. This process shall be recorded on the QAIF (3.11.1). At the time of Coast Guard inspection, every shackle assembly, shackle pin, Modeer shackle assembly, and swivel offered shall have successfully passed the proof load test as specified in paragraph 3.4. The Contractor shall certify this by submitting a Certificate of Performance (see 6.2) for each batch offered. In addition, at the time of Coast Guard inspection, the Contractor shall proof test the samples chosen in accordance with paragraph 4.4.2 in the presence of the COR. If any item fails the proof test at this time, it shall be considered a major defect.

4.5.3.2 Method of proof load testing. Shackle assemblies, Modeer shackle assemblies, and swivels shall be proof tested assembled. These items may be proof tested individually or in a series. When shackle pins are to be furnished alone, they may be proof tested individually, or by inserting them into shackle bodies of the appropriate class and tested as assemblies. Application of the proof load shall be at the centerline of the sample. The diameter of the attachments used in the proof tests shall not be greater than the size of the sample being tested.

4.5.3.3 Breaking load test. The Contractor shall perform breaking load tests in the presence of the COR, using samples chosen in accordance with paragraph 4.4.2. Shackle assemblies, Modeer shackle assemblies, and swivels shall be break tested assembled. When shackle pins are to be furnished alone, they may be break tested individually, or by inserting them into shackle bodies of the appropriate class and tested as assemblies. Application of the breaking load shall be at the centerline of the sample. The diameter of the attachments used in the breaking load tests shall not be greater than the size of the sample being tested.

4.6 Inspection of packaging and marking. The Coast Guard inspection to determine compliance with the requirements of section 5 will be performed at the point of destination. Items received at the point of destination, which are not packaged and marked in accordance with the requirements of section 5, will be rejected.

5. PRESERVATION, PACKING, MARKING, AND SHIPPING

5.1 Preservation. Per MIL-SPEC-2073-1E, Method 10.

5.2 Packing. Shall be in accordance with MIL-SPEC-2073-1E Level B, to protect these assemblies and items during moderate worldwide shipment, handling, and storage conditions.

5.2.1 Shipping Containers.

5.2.1.1 Shackle Assemblies, shackle pins, swivels. Shackle assemblies, shackle pins, Modeer shackle assemblies, and swivels shall be packed in clean steel drums or barrels (30, 55 or 80 gallon capacity). The top of each drum or barrel shall be fitted with a cover or laced with wire rope to prevent spilling of the contents. Covers shall not be welded in place. The contents of a drum or barrel shall be limited to a single National Stock Number.

5.2.1.2 Drainage Holes. A minimum of five, maximum of seven ¼” to ½” holes (1/2” hole maximum diameter) shall be punched through the bottom(s) of the steel drums or barrels from the inside going out to provide drainage. The holes shall be at least 4” apart from each other and shall be placed at least 5” away from the side of the steel drums or barrels towards the center of the bottom so as to not weaken the structural integrity of the steel drums or barrels.

5.2.1.3 Split Keys. Split keys, when purchased alone, and not as part of split key shackle assemblies, shall be packed in triple-wall fiberboard boxes conforming to ASTM D5168, utilizing either metallic or non-metallic strapping. The contents of each box shall be limited to a single National Stock Number. A maximum of 250 split keys of any class shall be packed per box. The split keys shall be cushioned, braced, or blocked to prevent excessive movement.

5.2.1.4 Disposition of Shipping Containers. Shipping containers described in the preceding paragraphs, as used, shall become the property of the U.S. Coast Guard.

5.2.1.5 Palletized Shipments. Palletized shipments shall normally be confined to a single National Stock Number per pallet. Mixed pallets shall be clearly and legibly marked “MIXED STOCK”.

5.3 Marking. Each package is to be individually marked in accordance with MIL-STD-129R.

5.3.1 Marking Layout. Steel drums or barrels shall be legibly stenciled in ¾ inch high letters with the information listed below. See example 6.3 for stencil locations. Boxes of split keys shall be legibly marked with the same information on a label per MIL-STD-129R. See example 6.4.

NATIONAL STOCK NUMBER 4030-00-236-8403

CAGE CODE (Contractor’s)

PART NUMBER 121079 Shackle ASSY SPLTKEY 1st Class

QUANTITY & UNIT OF ISSUE 1 EA

CONTRACT NUMBER (See Contract Page 1)

DELIVERY ORDER NUMBER (See Contract)

MANUFACTURED DATE MFD 04/18

SHIPPING WEIGHT (LBS) WT (As Determined by Contractor)

CONDITION CODE CONDITION A

OTHER DATA AS DIRECTED USCG SILC-WOPL MATERIAL

5.4 Bar coding. The Contractor shall apply bar coding of the National Stock Number, IAW ISO/IEC 16388-2007 Code 39 Symbology. See example 6.5.

5.4.1 Bar code label. The Contractor may apply separately or as part of the marking required in 5.3.

5.5 Shipping. The Contractor shall deliver the parts and components to the Coast Guard address specified in paragraph 5.5.2. Notify the Contracting Officer’s Representative (COR) and Contracting Officer (KO) about the shipment (7) business days in advance. Provide the COR with the name of the shipping company, date of shipment leaving Contractor’s facility, and expected arrival date and time at the Coast Guard facility. Normal delivery hours at the warehouse are Monday through Friday 0730-1300 (excluding Federal Holidays). Deliveries outside this window shall require prior written approval by the Contracting Officer.

5.5.1 All items shall be shipped FOB Destination.

5.5.2 Address. Unless otherwise specified, the Contractor shall ship, and deliver all parts to the following government addresses:

US Coast Guard

Surface Forces Logistics Center

2401 Hawkins Point RD, Receiving Room - Bldg 88

Curtis Bay, MD 21226

6. NOTES

6.1 Document sources.

6.1.1 Coast Guard documents.

United States Coast Guard Shore Infrastructure Logistics Center

Waterways Operations Product Line

300 East Main Street

Norfolk, VA 23510-9104 http://www.dcms.uscg.mil/Our-Organization/Assistant-Commandant-to-Engineering-Logistics- CG-4-/Logistic-Centers/Waterways-Operation-Product-Line/

6.1.2 Industry Publications.

(ANSI/AIM) American National Standards Institute USA

25 West 43rd Street, 4th floor

New York, NY 10036

Office 212-642-4900 Fax 212-398-0023

Customer Service or Document Sales 212-642-4980 0830-1800

(ANSI/ASQ) American Society for Quality Control

310 West Wisconsin Avenue

Milwaukee, Wisconsin 53203 http://asq.org/index.aspx

(ASTM) American Society for Testing & Materials

100 Barr Harbor Drive

P.O. Box C700

West Conshohocken, PA 19428-2959

Office 610-832-9500 Fax 610-832-9555

(ISO) International Organization for Standardization BIBC II

Chemin de Blandonnet 8, CP 401

1214 Vernier, Geneva, Switzerland

Phone +41 22 749 01 11 Fax: +41 22 733 34 30

Email: central@iso.org

6.1.3 Military Standards and Specifications.

Defense Printing Service Detachment Office

Bldg. 4D (NPM-DODSSP)

700 Robbins Avenue

Philadelphia, PA 19111-5094

215-697-2667 or -2179 Fax 215-697-1462

DOD & Navy Publications & Forms (Other Than DODSSP)

Naval Publication and Forms Center

5801 Tabor Avenue

Philadelphia, PA 19120 215-697-2000Naval Publication and Forms Center

5801 Tabor Avenue

Philadelphia, PA 19120 215-697-2000

6.2 Certificate of Performance.

CERTIFICATE OF PERFORMANCE

Contract No. ______________________________

Item ________________________ Batch No.___________________

I hereby certify that all items in the above numbered batch submitted for the above numbered contract have successfully passed the proof load test as specified in paragraph 3.4 of U.S. Coast Guard Specification No. 417G.

Signed_______________________ Date_________________________

Title ____________________________

6.3 Stencil Placement Locations.

NOTE: For identification bar code specific marking locations.

Placement of identification and address marking on barrels, drums, and other cylindrical containers.

6.4 Military marking example.

Example of unit pack, intermediate and exterior container identification markings (including an example of bar code markings).

Note

The label on a steel drum will only utilize the EXTERIOR CONTAINER Label format.

6.5 Bar coding example.

SPECIFICATION NO. 417 REV G - FOR FABRICATION OF BUOY

SHACKLES, MODEER SHACKLES, AND SWIVELS

Prepared by: Reviewed by:

Mr. M. J. Beimel LT. Rudy Bowis

Equipment Specialist, Waterways Operations Asset Line Manager, Waterways Operations

Product Line Product Line

Approved by: Date:

Mr. Wayne Danzik

Deputy Manager, Waterways Operations

Product Line

BEIMEL.MICH

AEL.JOSEPH.1

316952271

Digitally signed by

BEIMEL.MICHAEL.JOSEPH.1316952271

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USCG, cn=BEIMEL.MICHAEL.JOSEPH.13169522 Date: 2018.04.02 12:04:57 -04'00'

BOWIS.RUDY.

H.1274982582

Digitally signed by

BOWIS.RUDY.H.1274982582

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USCG, cn=BOWIS.RUDY.H.1274982582 Date: 2018.04.02 12:27:03 -04'00'

DANZIK.WAYN

E.S.1273020744

Digitally signed by

DANZIK.WAYNE.S.1273020744

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USCG, cn=DANZIK.WAYNE.S.1273020744 Date: 2018.04.02 14:06:18 -04'00'