Attachment A InnoWave Pro Equipment Specs.pdf

T I T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 101

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Physical dimensions and weight

External height (lid closed)

43.6 in. 1109 mm

External height (lid open)

65.3 in. 1659 mm

External width 49.6 in. 1260 mm

External depth

36.1 in. 918 mm

Net weight (dry)

905 lbs

410 kg

Operating weight (tank filled)

380 lbs

172 kg

Max. operating weight (incl. filled tank, chemicals, and instruments to be cleaned)

1162 lbs

527 kg

External Dimension i n m m i n m m

49.63 in. [1260 mm] i n m i n m

T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 101A

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Suggested Clearances When Servicing Machine

18.0

18.0

18.0

18.0

Notes:

1. Clearances are in INCHES

2. Machine should be moved to a position with minimum clearances shown for servicing.

3. Space for service clearances are not required while the unit is in the installed position.

4. Adequate space should be provided in the room for servicing the machine, so it can be wheeled or moved to accommodate servicing.

5. Reference other pages for installation clearances.

90.0

T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 102

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Utility Connections

REAR VIEW WITH LID CLOSED, SHOWING SERVICES

1113mm [4 4]

268mm [11]

Reverse Osmosis WATER 3/4" BSPP

HOT WATER 3/4" BSPP

COLD WATER 3/4" BSPP

OVERFLOW

NB. DO NOT

RESTRICT

OR BLOCK

165,1mm [6]

230,1mm [9]

295,1mm [12]

345,1mm [14]

395,1mm [16]

211,6mm [ 8] i n

MAINS POWER ENTRY

REMOVABLE REAR

ACCESS PANELS

TEMPERING VALVE

MAINTAIN AIR GAP

DO NOT BLOCK

MACHINE BASE REAR

AIR SUPPLY 0.32 in [8 mm] O.D. TUBE

PRINTER RS232

D-SUB FEMALE

EXPANSION PORT

COLD WATER DRAIN COOLING

FLEXIBLE RUBBER HOSE 3/4" FEMALE

6.75 in. [170 mm]

DO NOT BLOCK

MACHINE BASE REAR

COLD WATER DRAIN COOLING

FLEXIBLE RUBBER HOSE 3/4" FEMALE

3.50 in. [90 mm]

DRAIN OUTSIDE OF MACHINE'S FOOTPRINT

REAR VIEW WITH LID CLOSED

4.00 in. [104.6 mm]

10.50 in. [268 mm]

15.5 in. [395 mm]

13.63 in. [345 mm]

11.63 in. [295 mm]

9.00 in. [230 mm]

6.50 in. [165 mm] i n m m i n m m bottom of drain pipe to floor

T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 103

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Installed Operation Clearances

DRAIN WITHIN OR OUTSIDE MACHINE'S FOOTPINT

FRONT VIEW WITH LID OPEN

m m i n

5.88 in. [150 mm] 5.88 in. [150 mm] i n i n m m i n m m

49.63 in. [1260 mm]

CARRIER TOP

EMERGENCY STOP

CHEMICAL STORAGE

2 X 10 LITRES.

(DOORS OPEN)

DO NOT BLOCK GAP

BETWEEN SIDE & FRONT

KICKPLATES AND FLOOR

CONTROL PANEL

(COVER REMOVED

FOR CLARITY)

FOOT SWITCH

CONTROL

ELECTRICAL PANEL

(COVER REMOVED

FOR CLARITY)

4.3" TFT TOUCH

DISPLAY

TEMPERING VALVE MAINTAIN AIR GAP

T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 104

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Installed Operation Clearances

DRAIN WITHIN MACHINE'S FOOTPRINT

TOP VIEW

DRAIN

FLOOR SINK

150mm [6]150mm [6]

200mm [8]

STAINLESS STEEL TUBE

1 METER LONG STAINLESS STEEL PIPE SUPPLIED

CAN BE CUT DOWN TO SUIT

POSITION ANY DIRECTION

AT REAR FROM DRAIN OUTLET

PIPE MUST SLOPE TOWARD DRAIN.

CAN PASS THROUGH WALLS

AS REQUIRED.

49.63 in. [1260 mm]

6 in. [152 mm] i n

267,8mm [11] i n i n m m

DOOR SWING

Installed Operation Clearances

DRAIN OUTSIDE OF MACHINE'S FOOTPRINT

TOP VIEW

5.88 in. [150 mm] 5.88 in. [150 mm] i n m m

10.5 in. [268 mm]

T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 105

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Installed Operation Clearances

DRAIN WITHIN MACHINE'S FOOTPRINT

SIDE VIEW

Installed Operation Clearances

DRAIN OUTSIDE OF MACHINE'S FOOTPRINT

SIDE VIEW

(1113mm [

44] OVERA

LL CLOSE

D)

101mm [4]

CLOSED

868,6mm [34]

503,5mm [20]

Ø53,9mm [2] I/D

200mm [8] i n

6 in. [152 mm]

SILICONE ELBOW TUBING

TO CONNECT TO DRAIN

STAINLESS STEEL TUBE

1 METER LONG STAINLESS STEEL PIPE SUPPLIED

CAN BE CUT DOWN TO SUIT

POSITION ANY DIRECTION

AT REAR FROM DRAIN OUTLET

PIPE MUST SLOPE TOWARD DRAIN.

CAN PASS THROUGH WALLS

AS REQUIRED.

0.63 in. [14 mm]

34.25 in. [869 mm]

7.88 in. [200 mm] i n m m

C

L O

S E

D i n m m

O

V E

R A

L L

C

L O

S E

D

19.88 in. [503 mm]

Ø 2.13 in. [54 mm] ID

TEMPERING VALVE MAINTAIN AIR GAP

AutoCAD SHX Text E

T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 106

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Installed Operation Clearances

DRAIN WITHIN MACHINE'S FOOTPRINT

SIDE VIEW

Installed Operation Clearances

DRAIN OUTSIDE OF MACHINE'S FOOTPRINT

SIDE VIEW

503,5mm [20]

Ø53,9mm [2] I/D

200mm [8] i n

6 in. [152 mm]

(1663mm [

65] OVERA

LL OPEN)

651mm [26

] OPEN

11.5 in. [293 mm]

REACH

SILICONE ELBOW TUBING

TO CONNECT TO DRAIN

STAINLESS STEEL TUBE

1 METER LONG STAINLESS STEEL PIPE SUPPLIED

CAN BE CUT DOWN TO SUIT POSITION ANY DIRECTION

AT REAR FROM DRAIN OUTLET PIPE MUST SLOPE TOWARD DRAIN.

CAN PASS THROUGH WALLS AS REQUIRED.

7.88 in. [200 mm]

19.88 in. [503 mm]

Ø 2.13 in. [54 mm] I/D i n m m

O

V E

R A

L L

O

P E

N i n m m

O

P E

N

TEMPERING VALVE MAINTAIN AIR GAP

AutoCAD SHX Text E

T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 107

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Water supply requirements:

Water hardness (CaCO3), quality and purity, hot and cold supplies

< 125 ppm with water quality and purity tested and approved for disinfection as per ANSI/AAMI ST 15883-1:2009 (item 6.4.1 and

6.4.2) or AAMI TIR 34

Pressure (hot and cold), Static 30 to 70 psi (2.0 to 5.0 Bar)

Flow rate (hot and cold) 3 to 8 gal/min. (11 to 30 litres/min.)

Temperature (hot and cold) Cold: +41 to 86 ºF (+5 to 30 ºC) Hot: +122 to 176 ºF (+50 to 80 ºC)*

Connections

3/4 in. BSP male thread Rubber gasket is required. Do not use tape or any sealant, 3/4" NPT facility connections required. Hose connections will not work. Do not hard pipe water connections.

Machine must be easily movable for service and maintenance.

*The unit is able to operate without hot water connection or with hot water supply cooler than recommended minimum temperature of +122 ºF (+50 ºC). Using only cold water or low-temperature hot water will result in longer cycle operation as water takes longer to heat up in unit.

Typical water consumption per wash

Water consumption will vary depending on volume of instruments loaded and temperature of inlet water supply. The water consumption below describes complete wash cycle at +104 ºF (+40 ºC), with no instruments loaded.

Maximum water consumption for complete wash cycle

Stage

Cold water Hot water RO Water *

Total for stage

Pre-wash

10.6 gallons

(40 litres) nil nil

10.6 gallons

(40 litres)

Wash

1 gallon

(3.7 litres)

65 gallons

(246 litres) nil

66 gallons

(250 litres)

Rinse

10.6 gallons

(40 litres) nil nil

10.6 gallons

(40 litres)

Disinfection

10.6 gallons

(40 litres) nil

10.6 gallons

(40 liters)

21.2 gallons

(40 litres)

Disinfection Condensate

43.5 gallons

(165 liters) nil nil

43.5 gallons

(165 liters)

Cooling

28 gallons

(105 liters) nil nil

28 gallons

(105 liters)

Total water consumption

104.3 gallons

(393 litres)

65 gallons

247 (litres)

10.6 gallons

(40 liters)

180 gallons

(681 litres) includes 38 gallons R.O.

*If RO is used, cold water is not used during disinfection

T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 108

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Site drain requirements The site drain should meet the following requirements:

Drain connection

2.125 in. (54 mm) outlet from unit.

Drain must be fitted with suitable traps.

Remote drain must slope to floor drain. Air gap must be maintained per local code.

Do not hard pipe drain connection. The machine must be easily movable for service and maintenance.

Position

Unit should be positioned so that the centerline of the unit is aligned with the center of the floor sink outlet.

If remote drain is used, drain line must be level or sloping away from unit.

Remote drain also requires a floor sink.

Adhere to local code.

Capacity

47.5 gallons/minute. (30 litres/minute) Maximum discharge to drain including overflow, (minimum drain capacity of 8 gallons/minute). When drain tempering valve is installed, maximum flow to drain is 8 gallons/minute including DTV cooling water flow rate.

Overflow Drain

Internally connected within the machine to the drain pipe, downstream of the drain valve. Maximum overflow drain is 8 gallons per minute.

Effluent temperature up to +140 ºF (+60 ºC) Max. and +203 ºF (+95 ºC) without DTV kit. DTV is required in North America. Other locations refer to local or national codes.

Floor Sink

Dimensions

6.0 in x 6.0 (152 mm x 152mm) in with a 3.0 in. (76 mm) minimum drain outlet at bottom of floor sink.

Compressed Air

Supply

Pressure: 5.5 bar to 7.0 bar (80 to 100 psi).

Quality: If medical grade compressed air is not used, and Eliminizer filter needs to be included at time of order.

Connection: 8mm (0.315 in) dia. Quick fit hose connector.

T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 109A

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Electrical power supply requirements:

Requirement

Model

IWPRO60

Electrical supply voltage

200-230 V AC 3P+PE

(Three-phase and protective earth)

Frequency: 60 Hz

Supply current

Site Current Capacity Current Capacity: >48 A per phase

Dedicated circuit is required with a minimum circuit breaker rating of 63A or greater. Refer to local codes

Electrical power requirement

18 kW

Allowable supply voltage fluctuation ±10% of nominal voltage

Over-voltage category II Transient over-voltages typically present on mains supply

Electrical connections

Model Conductor

Color and Marking

IWPRO60 (208 V AC 3P+PE)

supplied with 6 ft (1.8 m) 4-core power cable.

Protective earth Green/Yellow

Live 1 Black 1

Live 2 Black 2

Live 3 Black 3

The disconnect switch must:

-- Isolate all poles simultaneously

-- Be lockable in the off position

-- Comply with standards IEC/EN 61058-1 and IEC 60447 (creepage and clearances for 4kV transient voltage)

-- Be situated close to the equipment for ease of accessibility, and in a position where the operator can turn it off in an emergency without leaning over the machine.

-- Marked as the disconnection device for this equipment

-- Disconnect device off-position should be clearly marked (O) and the on-position should be marked (l)

-- Hard wiring power cable to disconnect switch is recommended. Use of an electrical plug is not recommended.

T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 109B

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Electrical power supply requirements:

Requirement

Model

IW532055NPR

Electrical supply voltage

380V-415V 3P+N+PE

(Three-phase, neutral and protective earth)

Frequency: 50 Hz

Supply current

Site Current Capacity: >33 A per phase

Dedicated circuit is required with a circuit breaker rating of 40A or greater. Refer to local codes.

Electrical power requirement

22 kW

Allowable supply voltage fluctuation ±10% of nominal voltage

Over-voltage category II Transient over-voltages typically present on mains supply

Electrical connections

Model Conductor

Color and Marking

IW532055NPR(380-415VAC 3P+N+PE)

supplied with 9.84 ft (3 m) 5-core power cable

Protective earth Green/Yellow

Live 1 Brown

Live 2 Black

Live 3

Grey

Neutral Blue

Typical power consumption per wash

Power consumption will vary depending on cycle settings and temperature of inlet water supply. The power consumption below describes complete wash cycle at +104 ºF (+40 ºC).

Maximum power consumption for complete wash cycle

Phase

Power consumption kWh

Pre-wash 11.9

Wash 2.6

Rinse 1 0.6

Rinse 2 0.6

Disinfection 3.6

Total power consumption

9.3

T L E

Corporation SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

A

OF 10 10

NTS TJ B1101826211393356

Equipment Specifications built after SN: 11189855522 InnoWave Pro

Operating / Working environment location requirements

General and environmental requirements

Proposed operating location for unit much meet or exceed following requirements

Description Requirements

Operating surface

On level floor, capable of supporting a weight of at least 1200 lb

(545 kg).

Location requirement Altitude Indoors only, altitude up to 6562 ft (2000 m)

Ambient operating temperature range

+41 ºF to 104 ºF (+5 ºC to 40 ºC)

Maximum humidity

80% relative humidity for up to +88 ºF (+31 ºC) decreasing linearly to 50% relative humidity at +104 ºF (+40 ºC)

Site services

Within 6 ft (1.8 m) of electrical isolator.

Within 6 ft (1.8 m) of hot and cold water connections.

Within 3 ft (1.0 m) of external site drain for effluent.

Ambient lighting 500 lux (46.5 foot-candle) minimum room lighting

Noise generated during operation 69 dBA at distance of 6 ft (1.8 m) from front of unit

Heat output during operation 7200 BTU/hr during cycle

Shipping crate dimensions and weight

Shipping crate height

59.1 in. 1501 mm

Shipping crate width

59.5 in. 1511 mm

Shipping crate depth

45.3 in. 1151 mm

Shipping crate gross weight

1135 lb

515 kg

Shipping information

Transportation and storage:

Make sure package marking instructions and environmental conditions are always followed during transport and storage of InnoWave™ Pro.

Lifting:

Lifting and maneuvering the InnoWave™ Pro in shipping crate must be done with pallet truck or forklift truck able to carry load in excess of 1135 lb (515 kg).

Storage markings:

The markings on shipping crate stipulate unit's storage conditions and handling information.

Keep dry This way up