260-B4260-058 NVCC Renovate 3rd Floor Lab - BID SET Drawings.pdf

PDF 7 MB Posted Sep 2, 2026

Attached to: 260-B4260-058 NVCC Renovate 3rd Floor Lab
Solicitation number: IFB-126793
Issued by: Fairfax County, Virginia

About this file

Written by GovTribe AI · Sep 9, 2026

This is a bid set of construction drawings for the Northern Virginia Community College (NVCC) Annandale Campus renovation project, specifically for reconfiguring the third-floor laboratory and classroom spaces in the CM-McDiarmid Building. The project, identified as 260-B4260-058, involves the selective demolition of the existing partition wall separating rooms CM311 (Group Study/Computer Class Room) and CM365 (Oral Communication Center), resulting in a combined 1,331 square feet of renovated space. The scope includes removal and replacement of affected floor finishes and ceiling grid elements, patching and painting of wall areas, installation of new floor and wall-mounted power outlets, and provision of new electronic door access (EDA) systems to existing fire-rated doors. The drawings were issued for the bid set on August 5, 2026, and were prepared by Dewberry Engineering Inc. The building is located at 8333 Little River Turnpike, Annandale, Virginia 22003, and is owned by the Commonwealth of Virginia State Board of Community Colleges. The project must comply with the 2021 Virginia Construction Code, International Building Code, International Mechanical Code, International Plumbing Code, NFPA 70 National Electric Code (2020), and Virginia Energy Conservation Code (2021).

The renovation is classified as an Alteration Level 2 project under the Virginia Existing Building Code, with a work area of 1,433 square feet representing less than 50 percent of the building's total 58,912 square foot gross area. The building, originally constructed in 1993, is classified as Use Group B (Business) with Construction Classification IIB (Unprotected) and contains automatic sprinkler, fire alarm, and standpipe systems. The design includes fire-rated partition assemblies, mechanical systems with fan-powered terminal units, fire protection systems including sprinkler and standpipe coordination, and complete electrical systems including lighting, fire alarm, power distribution, and emergency circuits. The project incorporates compliance with ADA Title II accessibility standards and high-performance building considerations, though the renovation cost does not exceed 50 percent of building value and is therefore exempt from certain High Performance Building Act requirements. Energy compliance must achieve performance equal to or less than 80 percent of the standard reference design building per VECC standards.

View the file

Other files

File	Type	Posted
260-B4260-058 NVCC Renovate 3rd Floor Lab - Addendum_1.pdf	PDF	Sep 2, 2026
260-B4260-058 NVCC Renovate 3rd Floor Lab - BID SET Project Manual.pdf	PDF	Sep 2, 2026
260-B4260-058 NVCC Renovate 3rd Floor Lab - Notice of Invitation For Bids.pdf	PDF	Sep 2, 2026

On GovTribe

Work with this file

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

54321

KEY PLAN

APPROVED BY

CHECKED BY

SHEET NO.

TITLE

DRAWN BY

DATE

PROJECT NO.

SEAL

REVISIONS

P M

COVER SHEET

08/05/2026

50186890

C M

-M C

R M

G R

E N

O V

A T

R D

F L

O O

B #2

-B

-0

N V

C C

N N

A N

D A

A M

P U

U E

D F

O R

S E

E R

T U

R N

A N

N A

N D

Dewberry Engineering Inc.

8401 ARLINGTON BOULEVARD

FAIRFAX, VA 22031 -4666

703.849.0100

G-001

NVCC ANNANDALE CAMPUS - CM - MCDIARMID BUILDING

RENOVATE 3RD FLOOR LAB

PROJECT #260-B4260-058/L24NV548

ISSUED FOR BID SET

AUGUST 05, 2026

CONSULTANTS

ARCHITECTURE & MEP

BUILDING LOCATION:

NVCC ANNANDALE CAMPUS CM - McDiarmid BUILDING:

8333 LITTLE RIVER TURNPIKE, ANNANDALE VA 2003

SITE INFORMATION

OWNER OF BUILDING:

COMMONWEALTH OF VIRGINIA

STATE BOARD OF COMMUNITY COLLEGES

PRIMARY CONTACTS:

OWNER: NORTHERN VIRGINIA COMMUNITY COLLEGE

FACILITIES PLANNING AND SUPPORT SERVICES

8333 LITTLE RIVER TURNPIKE, CW BUILDING

SUITE 311, ANNANDALE, VA 22003-3796

PHONE: 703.323.3551

APPLICABLE CODE AND CRITERIA:

ALL WORK SHALL COMPLY WITH THE FOLLOWING CODES:

VIRGINIA CONSTRUCTION CODE (VCC) -

INTERNATIONAL BUILDING CODE -

INTERNATIONAL MECHANICAL CODE -

INTERNATIONAL PLUMBING CODE -

NFPA 70 NATIONAL ELECTRIC CODE (NEC) -

VIRGINIA ENERGY CONSERVATION CODE (VECC) -

VIRGINIA EXISTING BUILDING CODE (VEBC). ALT 2-

VIRGINIA UNIFORM STATEWIDE BUILDING CODE (VUSBC) -

ADA 90 TITLE II: ASAD CHAPTER 2 FOR SCOPING -

ICC A117.1- CHAPTER 1 AND 3 THRU 11 FOR TECHNICAL REQUIRED

VIRGINIA COMMUNITY COLLEGE SYSTEM

CONSTRUCTION AND PROFESSIONAL SERVICES

MANUAL, (CPSM), .........................................................................2025 REV (0) 03/17/25

IN THE EVENT OF A CONFLICT, THE MOST RESTRICTIVE CODE

SHALL PREVAIL

CALL BEFORE YOU DIG:

VIRGINIA ONE CALL

811 OR 1-800-552-3120

3 WORKING DAYS UTILITY NOTIFICATION

PRIOR TO CONSTRUCTION

DEWBERRY

8401 ARLINGTON BLVD

FAIRFAX, VA 22031

T: 703.849.0100 F: 703.698.9040

DRAWING LIST

SHEET NO. SHEET TITLE. .

GENERAL

G-001 COVER SHEET

G-002 STANDARD ABBREVIATIONS & SYMBOLS

G-003 BUILDING CODE PLAN - THIRD FLOOR

G-004 PENETRATION DETAILS

G-005 UL DESIGN ASSEMBLY & PARTITION WALL

ARCHITECTURAL

A-111 THIRD FLOOR DEMO WORK PLAN

A-112 THIRD FLOOR NEW WORK PLAN

A-201 FINISH/ FURNITURE PLAN & DOOR SCHEDULE

MECHANICAL

M-001 MECHANICAL SYMBOLS, LEGEND, NOTES

M-111 MECHANICAL THIRD FLOOR NEW WORK PLAN

FIRE PROTECTION

FP-111 FIRE PROTECTION THIRD FLOOR NEW WORK PLAN

ELECTRICAL

E-001 ELECTRICAL SYMBOLS, LEGENDS, NOTES

E-002 ELECTRICAL ABBREVIATIONS

E-110 ELECTRICAL THIRD FLOOR OVERALL FLOOR PLAN

E-111 ELECTRICAL THIRD FLOOR NEW WORK LTG & FIRE ALARM PLAN

E-112 ELECTRICAL THIRD FLOOR NEW WORK POWER PLAN

E-601 ELECTRICAL RISER DIAGRAM PANEL SCHEDULES

DRAWING INDEXGENERAL INFORMATION

ASBESTOS COMPLIANCE STATEMENT (ALL BUILDING):

AN ASBESTOS INSPECTION WAS NOT TO BE PERFORMED BECAUSE ALL PORTIONS OF THE

EXISTING BUILDING THAT MAY BE AFFECTED BY THE WORK WERE ORIGINALLY CONSTRUCTED

AFTER JANUARY 1, 1985.

NO ASBESTOS CONTAINING MATERIAL SHALL BE USED ON THIS PROJECT.

LEAD COMPLIANCE STATEMENT (ALL BUILDING):

AN INSPECTION TO IDENTIFY LEAD CONTAINING OR COATED BUILDING COMPONENTS HAS

NOT BEEN CONDUCTED BECAUSE THE BUILDING WAS CONSTRUCTED AFTER JANUARY 1, 1985

AND THE OWNER HAS NO KNOWLEDGE OF LEAD CONTAINING OR COATED BUILDING

COMPONENTS IN THE BUILDING. IT IS THE CONTRACTOR'S RESPONSIBILITY TO COMPLY WITH

ALL VIRGINIA OCCUPATIONAL SAFETY AND HEALTH (VOSH) REGULATIONS AS THEY PERTAIN

TO EMPLOYEE EXPOSURES TO LEAD. ALL LEAD AND LEAD-COATED BUILDING COMPONENTS

SHALL BE RECYCLED TO THE EXTENT POSSIBLE.

HIGH PERFORMANCE BUILDINGS ACT NOTICE:

IN ACCORD WITH THE HIGH PERFORMANCE BUILDING ACT, THE BUILDINGS ARE EXEMPT

FROM COMPLIANCE BECAUSE THE COST OF THE RENOVATIONS DOES NOT EXCEED 50%

OF THE VALUE OF EACH BUILDING.

PROJECT NAME: NVCC ANNANDALE CAMPUS - CM BUILDING 3RD FLOOR LAB RENOVATION

PROPOSED SCOPE OF WORK:

• SELECTIVE DEMOLITION OF EXISTING PARTITION WALL THAT SEPARATES THE FOLLOWING ROOMS;

GROUP STUDY (#311) AND ORAL COMMUNICATION CENTER (#365).

• THE SCOPE INCLUDES:

1. REMOVING OF THE AFFECTED FLOOR FINISH AREA TO REPLACE IT IN KIND

2. REMOVING THE AFFECTED CEILING PANEL/ CEILING GRIDS TO REPLACE IT IN KIND

3. PATCHING AND PAINTING AFFECTED WALL AREA

4. PROVIDE NEW FLOOR AND WALL MOUNTED POWER OUTLETS

5. PROVIDE NEW ELECTRONIC DOOR ACCESS (EDA) TO EXISTING FIRE RATED DOORS

VICINITY MAP

BUILDING ORIGINALLY PERMITTED WITH:

1993 VIRGINIA UNIFORM STATEWIDE BUILDING CODE

1988 UNIFORM FEDERAL ACCESSIBILITY

1988 CAPITAL OUTLAY MANUAL STANDARDS

1990 AMERICANS WITH DISABILITY ACT (ADA)

OCCUPANCY USE GROUP: B (BUSINESS)

CONSTRUCTION CLASSIFICATION: IIB (UNPROTECTED)

AUTOMATIC SPRINKLER SYSTEM: YES

CONTAINS FIRE ALARM SYSTEM: YES

CONTAINS STANDPIPE SYSTEM: YES

CONTAINS FIRE EXTINGUISHER: YES

TOTAL BUILDING GROSS AREA: 58,912.40 SQUARE FOOT

TOTAL BUILDING VOLUME: 863,138.80 CUBIC FOOT

REFER TO SHEET G-003 FOR CODE AND LIFE SAFETY ANALYSIS.

CODE COMPLIANCE (ORIGINALLY CONSTRUCTED)

LOCATION MAP

NO. DESCRIPTION DATE

FOR VIRGINIA COMMUNITY COLLEGE SYSTEM

VECC 2021 COMPLIANCE PATH:

IN ACCORD WITH THE VIRGINIA ENERGY CONSERVATION CODE (VECC), THE BUILDING SHALL

COMPLY WITH VECC SECTIONS C402.5, C403.1.1, C403.1.2, C403.2, C403.3, C403.4 (EXCEPT C403.4.3 - C403.4.5), C403.5.5, C403.7 (EXCEPT C403.7.4.1), C403.8 (EXCEPT C403.8.6), C403.9, C403.11 (EXCEPT C403.11.3), C403.12, C403.13, C404, C405 (EXCEPT C405.3), C407 AND C408.

THE BUILDING ANNUAL ENERGY COST SHALL BE EQUAL TO OR LESS THAN EIGHTY (80)

PERCENT OF THE STANDARD REFERENCE DESIGN BUILDING.

SECTIONS C402.5 AND C404 ARE NOT APPLICABLE TO THIS PROJECT..

08/05/2026

A101

SIM

APC-X

8' - 0"

X#XX 1HR

SF01

Area Name

150 SF

FIRST FLOOR

100' - 0"

PT-X

RB-X

CPT-X

NOTES: 22

ROOM NAME

A101

SIM

GB-01

Scale:1 View Name 1/8" = 1'-0" 1/A101

A101

SIM

CALLOUT

BUILDING/WALL

SECTION

DETAIL SECTION

ROOM TAG

ROOM FINISH

TAG

CEILING TAG

DOOR / BORROWED

LITE TAG

WINDOW TAG

WALL TAG

FURNITURE,

CASEWORK, &

EQUIPMENT TAG

REVISION TAG

KEYNOTE TAG00 00 00.A1

AREA TO BE

ENLARGED SHEET REF.

PLAN / DETAIL

REF.

SECTION REF.

SHEET REF.

DETAIL REF.

SHEET REF.

LEVEL LINE

AREA SQUARE

FOOTAGE

ROOM NUMBER

EXTERIOR

ELEVATION

INTERIOR

ELEVATION

ELEVATION REF.

SHEET REF. A101

A101

1ELEVATION REF.

SHEET REF.

VIEW NAME

VIEW SCALE

VIEW DESIGNATION

VIEW REF/SHEET REF WHERE

VIEW IS REFERENCED

VIEW TITLE

WALL FINISH

BASE FINISH

FLOOR FINISH

AREA TAG

CEILING TYPE

CEILING HEIGHT

(ABOVE FINISH FLOOR)

LEVEL NAME

LEVEL ELEVATION

GRID LINE

NORTH INDICATOR

GRID NUMBER OR

LETTER

INDICATES PLAN NORTH

INDICATES TRUE NORTH

A101

SPOT ELEVATION

SYMBOL

NOTES

(AS NEEDED)

ROOM NUMBER

NEW DOOR EXISTING DOOR EXISTING DOOR

TO BE DEMOLISHED

WALL MOUNTED

LAVATORY

FLOOR MOUNTED

WATER CLOSET

WALL MOUNTED

TANKLESS WATER

CLOSET

COUNTER MOUNTED

LAVATORY

FLOOR MOUNTED

TANKLESS WATER

CLOSET

ELECTRIC WATER

COOLER

TOILET PARTITIONS

LOCKERS

SINGLE

DOUBLE

TRIPLE

QUAD

GRAB BARWALL MOUNTED

URINAL

54321

KEY PLAN

APPROVED BY

CHECKED BY

SHEET NO.

TITLE

DRAWN BY

DATE

PROJECT NO.

SEAL

REVISIONS

P M

STANDARD

ABBREVIATIONS

& SYMBOLS

08/05/2026

50186890

C M

-M C

R M

G R

E N

O V

A T

R D

F L

O O

B #2

-B

-0

N V

C C

N N

A N

D A

A M

P U

U E

D F

O R

S E

E R

T U

R N

A N

N A

N D

Dewberry Engineering Inc.

8401 ARLINGTON BOULEVARD

FAIRFAX, VA 22031 -4666

703.849.0100

G-002

AB ANCHOR BOLT

ACST ACOUSTIC(AL)

ADDL ADDITIONAL

ADDN ADDITION

ADH ADHESIVE

ADJ ADJACENT, ADJOINING,

ADJUSTABLE

AED AUTOMATED EXTERNAL

DEFIBRILLATOR

AFF ABOVE FINISH FLOOR

ALT ALTERNATE

ALUM ALUMINUM

ANCH ANCHOR

ANOD ANODIZE(D)

AP ACCESS PANEL

APC ACOUSTICAL PANEL CEILING

APPROX APPROXIMATE

ASPH ASPHALT

AUTO AUTOMATIC

AVE AVERAGE

AWT ACOUSTICAL WALL TREATMENT

BAL SHT BALANCE SHEET

BC BRICK COLOR

BCS BABY CHANGING STATION

BD BOARD

BG BUMPER GUARD

BITUM BITUMINOUS

BLDG BUILDING

BLKG BLOCKING (WOOD)

BOT BOTTOM

BRDG BRIDGING

BRG BEARING

BRK PV BRICK PAVERS

BRKT BRACKET

BSMT BASEMENT

BTWN BETWEEN

BUR BUILT UP ROOFING

CAB CABINET

CB CHALKBOARD

CC CUBICLE CURTAIN

CCT CUBICLE CURTAIN TRACK

CFCI CONTRACTOR FURNISHED

CONTRACTOR INSTALLED

CFMF COLD-FORMED METAL FRAMING

CG CORNER GUARD

CH COAT HOOK

CIP CONC CAST-IN-PLACE CONCRETE

CJ CONTROL JOING, CONSTRUCTION

JOINT

CLG CEILING

CLR CLEAR

CMU CONCRETE MASONRY UNIT

CNTR COUNTER

CO CLEAN OUT, CASED OPENING

COL COLUMN

COMB COMBINATION, COMBINED

COMP COMPRESSIBLE

COMPT COMPARTMENT

CONC CONCRETE

CONC CTG CONCRETE COATING

COND CONDITION

CONT CONTINUOUS

CONTR CONTRACTOR

CORR CORRIDOR

CPRS COMPRESSIBLE

CPT CARPET

CR CLOSET ROD

CRL CRASH RAIL

CRS COLD-ROLLED STEEL

CTR CENTER(S)

CUH CABINET UNIT HEATER

CUV CABINET UNIT VENTILATOR

CW CURTAINWALL

D DEEP, DEPTH, PENNY NAIL

DC DISPLAY CASE

DET DETAIL

DETN DETENTION

DF DRINKING FOUNTAIN

DIA DIAMETER

DIM DIMENSION

DN DOWN

DP DECORATIVE PANEL

DR DOOR

DS DOWNSPOUT

DWG DRAWING(S)

EHD ELECTRIC HAND DRYER

EJ EXPANSION JOINT

EL ELEVATION

ELEC ELECTRIC, ELECTRICAL

ELEV ELEVATOR

EMBED EMBEDMENT

EMER EMERGENCY

EPDM ETHYLENE PROPYLENE DIENE

MONOMER

EQ EQUAL

EQUIP EQUIPMENT

ES EXPOSED STRUCTURE

ETR EXISTING TO REMAIN

EW EACH WAY

EWC ELECTRIC WATER COOLER

EWH ELECTRIC WATER HEATER

EXIST EXISTING

EXP EXPANSION

EXT EXTERIOR

FAB FABRIC

FD FLOOR DRAIN

FDTN FOUNDATION

FE FIRE EXTINGUISHER

FEC FIRE EXTINGUISHER CABINET

FF FINISH FLOOR

FHC FIRE HOSE CABINET

FIN FINISH

FLASH FLASHING

FLP FLOOR PATTERN

FLR FLOOR

FRP FIBER REINFORCED PLASTIC

FTG FOOTING

FURG C FURRING CHANNEL

FURN FURNACE

FWC FABRIC WALLCOVERING

GA GAGE, GAUGE

GALV GALVANIZED

GB GRAB BAR

GFRC GLASS-FIBER REINFORCED

CONCRETE

GL GLASS

GL BLK GLASS BLOCK

GLZ CMU GLAZED CONCRETE MASONRY UNIT

GRFG GLASS-FIBER REINFORCED GYPSUM

GT GROUT

GWH GAS FIRED WATER HEATER

GYP BD GYPSUM WALL BOARD

H HIGH, HATCH (ROOF)

HB HOSE BIB

HDNR HARDENER

HDW HARDWARE

HDWD HARDWOOD

HM HOLLOW METAL

HORIZ HORIZONTAL

HR HANDRAIL

HT HEIGHT

HTG HEATING

HVAC HEATING, VENTILATING, AND AIR

CONDITIONING

ID INSIDE DIAMETER, INSIDE

DIMENSION

IF INSIDE FACE

INCL INCLUDED

INSUL INSULATION

INT INTERIOR

INV INVERT

JT JOINT

KD KNOCKED DOWN

KOP KNOCK OUT PANEL

L LONG, ANGLE

LAM LAMINATE(D)

LAV LAVATORY

LH LEFT HAND

LINO LINOLEUM

LKR LOCKER

LL LIVE LOAD, LOW LEVEL

LLH LONG LEG HORIZONTAL

LLV LONG LEG VERTICAL

LT LIGHT

LVL LEVEL

LVR LOUVER

MAS MASONRY

MATL MATERIAL

MAX MAXIMUM

MB MARKERBOARD

MBH MOB/BROOM HOLDER

MECH MECHANICAL

MED MEDIUM

MEZZ MEZZANINE

MFR MANUFACTURER

MH MANHOLE

MI MIRROR

MIN MINIMUM, MINUTE

MISC MISCELLANEOUS

MO MASONRY OPENING

MOD MODEL, MODULE, MODULAR

MSB MOP SERVICE BASIN

MT MOUNT

MTL METAL

NDU NEEDLE DISPOSAL UNIT

NIC NOT IN CONTRACT, NOISE ISOLATION

CLASS

NO NUMBER

NOM NOMINAL

NTS NOT TO SCALE

OA OVERALL

OC ON CENTER

OD OUTSIDE DIAMETER, OUTSIDE

DIMENSION

OF OUTSIDE FACE

OFCI OWNER FURNISHED CONTRACTOR

INSTALLED

OFD OVERFLOW DRAIN

OFOI OWNER FURNISHED OWNER

INSTALLED

OH OVERHEAD

OH DR OVERHEAD DOOR

OP OPERABLE PARTITION

OPH OPPOSITE HAND

OPNG OPENING

OPP OPPOSITE

OS OVERFLOW SCUPPER

PC PORTLAND CEMENT, POINT

OF CURVE, POLYCARBONATE

PCC PRECAST CONCRETE

PERIM PERIMETER

PJ PROJECTOR

PL PLATE, PLASTIC LAMINATE

PLAS PLASTER

PLBG PLUMBING

PLYWD PLYWOOD

PS PROJECTION SCREEN

PSF POUNDS PER SQUARE FOOT

PT PAINT

PTD PAPER TOWEL DISPENSER

PTDR PAPER TOWEL DISPENSER &

RECEPTACLE

PTN PARTITION

PTR PAPER TOWEL RECEPTACLE

PVC POLYVINYL CHLORIDE

PVG PAVING

R RISER, RADIUS, THERMAL

RESISTANCE (R-VALUE)

RB RESILIENT BASE

RCP REFLECTED CEILING PLAN

RD ROOF DRAIN, ROAD

REF REFERENCE, REFRIGERATOR

REINF REINFORCE

REQD REQUIRED

RF RESILIENT FLOORING

RFG ROOFING

RFM REMOVABLE FLOOR MAT

RH RIGHT HAND

RO ROUGH OPENING

RSF RESINOUS FLOORING

RST REINFORCING STEEL

RTF RESILIENT TILE FLOORING

RV ROOF VENT, ROOF VENTILATOR

SC SEALED CONCRETE

SCHED SCHEDULE

SCR SHOWER CURTAIN ROD

SCWD SOLID CORE WOOD DOOR

SD SOAD DISPENSER

SECT SECTION

SF STOREFRONT

SH SHINGLES, SINGLE HUNG (WINDOW)

SHT SHEET

SHTHG SHEATHING

SHV SHELVING

SLNT SEALANT

SND SANITARY NAPKIN DISPENSER

SNDU SANITARY NAPKIN DISPOSAL UNIT

SOG SLAB ON GRADE

SPCG SPACING

SPEC SPECIFICATION

SPKR SPEAKER

SQ SQUARE

SS SERVICE SINK , SOLID SURFACING

SST STAINLESS STEEL, SHOWER SEAT

STD STANDARD

STL STEEL

STL JST STEEL JOIST

STL LNTL STEEL LINTEL

STL PL STEEL PLATE

STL RF DK STEEL ROOF DECK

STL TR STEEL TRUSS

STN STAIN

STRUCT STRUCTURAL

SUSP SUSPEND

SV SHEET VINYL

SWP SHEET WALL PROTECTION

SYMM SYMMETRICAL

SYNTH SYNTHETIC

T TILE, TREAD

T&G TONGUE AND GROOVE

T/S TUB/SHOWER

TB TOWEL BAR, TACKBOARD

TC TOILET COMPARTMENT

TD TRENCH DRAIN

TER TERRAZZO

THK THICK

TOB TOP OF BEAM

TOC TOP OF CONCRETE, TOP OF CURB

TOF TOP OF FOOTING

TOM TOP OF MASONRY

TOS TOP OF SLAB, TOP OF STEEL

TOW TOP OF WALL

TPH TOILET PAPER HOLDER

TR TOWEL RACK

TS TUBE STEEL, TRANSITION STRIP

UNO UNLESS NOTED OTHERWISE

VCT VINYL COMPOSITION TILE

VERT VERTICAL

VIF VERIFY IN FIELD

VWC VINYL WALL COVERING

W WIDE, WEST

WC WALL COVERING

WD WOOD, WOOD DOOR

WDW WINDOW

WP WALL PATTERN, WATERPROOFING

WT WEIGHT, WINDOW TREATMENT

WWF WELDED WIRE FABRIC

STANDARD ABBREVIATIONS

STANDARD DETAILING SYMBOLS

STANDARD DRAFTING SYMBOLS

NO. DESCRIPTION DATE

239 SF

CONF. RM.

111 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

138 SF

FACULTY

OFFICE

126 SF

VESTIBULE

138 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

239 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

310 206 SF

STAIR

301B

122 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

120 SF

FACULTY

OFFICE

85 SF

ELEVATOR

301C

120 SF

FACULTY

OFFICE

813 SF

LOUNGE/LAB

261 SF

DIVISION

CHAIR

342A

9 SF

CLOSET

332A

271 SF

WOMEN

183 SF

WORK ROOM

621 SF

SECRETARY

241 SF

MEN'S

153 SF

ASSISTANT

DIVISION

CHAIR

342B

167 SF

ASSISTANT

DIVISION

CHAIR

342C

13 SF

STORAGE CLOSET

342D

230 SF

STAIR

122 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

206 SF

STAIR

301A

1538 SF

ART STUDIO

275 SF

PHOTOLAB

317B

27 SF

STORAGE

317D

23 SF

VESTIBULE

317A

35 SF

FILM

PROCESSING

317C

919 SF

DRAWING LAB

919 SF

DRAWING

LAB

580 SF

AMERICAN

CULTURE &

LANGUAGE

INSTITUTE

101 SF

ACLI OFFICE

327A

115 SF

ACLI OFFICE

327B

121 SF

ACLI OFFICE

327C

57 SF

ACLI LIBRARY

327D

69 SF

WORKROOM

327G

59 SF

WORKROOM

327H

75 SF

STORAGE

30 SF

COMM. CL.

154 SF

STORAGE

154 SF

FACULTY

OFFICE

119 SF

AV STOR

1107 SF

CORRIDOR

300D

1189 SF

CORRIDOR

300B

439 SF

CORRIDOR

300C

47 SF

ACLI LIBRARY

327E

14 SF

ELEC. CL.

122 SF

FACULTY

OFFICE

616 SF

CORRIDOR

300A

105 SF

BREAKROOM

327F

46 SF

JANITOR

2 22

1 11 1

1 11

1 11 1 1 1 1 1 1 1 1 1 1 1

2 2

1 11

EXISTING LIFE SAFETY LEGEND

1 - HR FIRE RATED PARTITION WALL

2 - HR FIRE RATED PARTITION WALL

EXISTING EXIT

EXISTING EXIT SIGN

AREA NOT IN SCOPE

EGRESS TRAVEL PATH

4 4

5 5

6 6

7 7

9 9

10 10

3 3

1 1

BUSINESS(CONCENTRATED)

1433 SF / 50 SF

LEGEND - OCCUPANCY AREA

BUSINESS(CONCENTRATED)

P A

T H

-A

54321

KEY PLAN

APPROVED BY

CHECKED BY

SHEET NO.

TITLE

DRAWN BY

DATE

PROJECT NO.

SEAL

REVISIONS

P M

BUILDING CODE

PLAN - THIRD

FLOOR

08/05/2026

50186890

C M

-M C

R M

G R

E N

O V

A T

R D

F L

O O

B #2

-B

-0

N V

C C

N N

A N

D A

A M

P U

U E

D F

O R

S E

E R

T U

R N

A N

N A

N D

Dewberry Engineering Inc.

8401 ARLINGTON BOULEVARD

FAIRFAX, VA 22031 -4666

703.849.0100

G-003 Scale: 3/32" = 1'-0"1 BUILDING CODE PLAN - THIRD FLOOR

NO. DESCRIPTION DATE

TRAVEL PATH DISTANCE SCHEDULE

PATH NAME PATH LENGTH

PATH-A

PATH-A 68' - 8 1/4"

APPLICABLE CODES: ALL WORK SHALL BE IN ACCORDANCE WITH VIRGINIA

UNIFORM STATE WIDE BUILDING CODES (VUSBC) PART II VIRGINIA

REHABILITATION CODE (VRC) - 2021

CLASSIFICATION OF WORK: IEBC C603.1 - ALTERATION LEVEL - 2

THIS INCLUDE THE ADDITION OR ELIMINATION OF ANY DOOR OR WINDOW, THE

RECONFIGURATION OR EXTENSION OF ANY SYSTEM, OR THE INSTALLATION OF

ANY ADDITIONAL EQUIPMENT, AND SHALL APPLY WHERE THE WORK AREA IS

EQUAL TO OR LESS THAN 50 PERCENT OF THE BUILDING AREA.

PROJECT AND CODE DATA (PROPOSED)

• CONSTRUCTION TYPE IIB: (UNCHANGED)

• GROSS BUILDING AREA: 58,912 SQ.FT (UNCHANGED)

• BUILDING HEIGHT = 58 FT (UNCHANGED)

• RENOVATED AREA USE GROUP : B (UNCHANGED)

• OCCUPANCY LOAD = 29

• PATH OF EGRESS: (UNCHANGED)

1. ALLOWED MAXIMUM TRAVEL DISTANCE = 250 FEET

2. PROVIDED MAXIMUM TRAVEL DISTANCE = 69 FEET

• SCOPE OF WORK AREA: 1,433 SQ.FT

• FULLY AUTOMATIC SPRINKLER SYSTEM THROUGHOUT THE BUILDING

PARTN TYPE WIDTH

O P

N G

P E

T E

S E

M B

L Y

FIRESTOP

DEVICE

1 TO 7 GANG

CABLES

RATED PARTN

TYPE AS

SCHEDULED

RATING NO:

MAX 4 HR, UL W-L-3218

OR EQ

FIRE RATED SEALANT

INTUMESCENT WRAP

STRIP AT PERIMETER

OF CABLE TRAY

BED CABLE IN FIRE

RATED SEALANT, PER

THE RATED ASSEMBLY

INSULATED CABLES

AND STEEL TRAY

INTUMESCENT SHEET

RATING NO:

3 HR UL C-AJ-4003,

OR EQ

CONCRETE

CMU

WALL,

SCHED

G P

PARTN TYPE WIDTH

O P

N G

P E

R R

A T

E D

A S

S E

M B

FIRE RATED SEALANT

INTUMESCENT WRAP

STRIP AT PERIMETER

OF CABLE TRAY

BED CABLE IN FIRE

RATED SEALANT, PER

THE RATED ASSEMBLY

INSULATED CABLES

AND STEEL TRAY

INTUMESCENT SHEET

RATED PARTN TYPE

AS SCHEDULED

RATING NO:

MAX 2 HR, UL W-L-4004,

OR EQ

METAL JUNCTION

BOX, SEPARATE

BACK TO BACK

BOXES 24" MIN

CMU PARTITION

TYPE AS

SCHEDULED

TYPICAL METAL

JUNCTION BOX,

MOUNT FLUSH W/

FACE OF CMU, AND

GROUT SOLID

AROUND BOX

PLAN

SECTION

RATED

PARTITION, AS

SCHEDULED

ACOUSTICAL

INSUL AS

SCHEDULED

TELEPHONE OR

ELECTRICAL COVER

PLATE

CONTINUOUS

ACOUS SEALANT

AROUND TEL & MET

ELEC OUTLET BOX

MOLDABLE FIRE-

STOPPING AROUND

TELEPHONE OR

ELEC OUTLET BOX

FILL BEHIND THE BOX

WITH FIRE BLANKET

INSULATION

" M

PARTITION AS SCHEDULED

ACOUSTICAL INSULATION

COVER PLATE

METAL STUDS

FLEX CABLE BETWEEN

"J" BOXES, WHERE

OCCURS

OUTLET BOX PAD

AROUND "J" BOXES

CONT ACOUS SEALANT

AROUND "J" BOXES

TYP MET "J" BOX

MOUNT ADJOINING "J"

BOXES IN SEPARATE

STUD CAVITIES

FIRE RATED SEALANT

EA SIDE OF PARTN W/

BACKER ROD

MET DUCT

UL COMPLYING STL BENT PLATE

RETAINING ANGLES, BOTH SIDES

OF PARTN, ATTACH TO DUCT W/

UL COMPLYING SM SCREWS,

OVERLAP PARTN OPNG 1" MIN

RATING NO:

MAX 2 HR, UL W-L-7008,

OR EQ

RATED GYP BD

PARTN, AS SCHED

DBL STUD FRAMED

OPNG, TYP

STOP DUCT INSUL @ FO

PARTN, SEAL VAPOR

BARRIER TO GYP BD

WHERE OCCURS

METAL SLEEVE WHERE

REQUIRED BY CONTRACT

DOCUMENTS

FIRE RATED SEALANT AND

PACKING - DEPTH AS REQ'D

BY RATED ASSEMBLY

ANNULAR SPACE PER

RATED ASSEMBLY

METAL PIPE

FILL AROUND SLEEVE IN

MASONRY CONSTRUCTION

W/ CEMENT MORTAR

RATING NO:

MAX 3 HR, UL C-AJ-1017,

OR EQ

CONCRETE

MASONRY

PARTN TYPE WIDTH

FIRESTOP

DEVICE

1 TO 7 GANG

CABLES

CMU/CONC PARTN

TYPE AS

SCHEDULED

RATING NO:

MAX 4 HR, UL W-J-3098

OR EQ

54321

KEY PLAN

APPROVED BY

CHECKED BY

SHEET NO.

TITLE

DRAWN BY

DATE

PROJECT NO.

SEAL

REVISIONS

P M

PENETRATION

DETAILS

08/05/2026

50186890

C M

-M C

R M

G R

E N

O V

A T

R D

F L

O O

B #2

-B

-0

N V

C C

N N

A N

D A

A M

P U

U E

D F

O R

S E

E R

T U

R N

A N

N A

N D

Dewberry Engineering Inc.

8401 ARLINGTON BOULEVARD

FAIRFAX, VA 22031 -4666

703.849.0100

G-004 Scale: 3" = 1'-0"9

TYP CABLE FIRESTOP DEVICE

THRU GYP BD

Scale: 3" = 1'-0"8

TYP CABLE TRAY

THRU CONC/CMU RATED WALL

Scale: 3" = 1'-0"7

TYP CABLE TRAY

THRU RATED GYP BD PARTN

Scale: 1 1/2" = 1'-0"6 TYP J BOX @ CMU PARTN Scale: 3" = 1'-0"5

TYP "J" BOX @ RATED

GYP BD PARTN

Scale: 3" = 1'-0"4

TYP "J" BOX @ GYP BD

PARTN W/ ACOUS INSUL

Scale: 3" = 1'-0"2

TYP MET DUCT

THRU RATED GYP BD PARTN

Scale: 3" = 1'-0"1

TYP PIPE/CONDUIT THRU

CONC/CMU RATED WALL

Scale: 3" = 1'-0"3

TYP. CABLE FIRESTOP DEVICE

THRU CONC/CMU

FIRE RATING:

STC RATING:

SOUND TEST:

SYSTEM THICKNESS:

LOCATION:

FRAMING TYPE:

1 HOUR

USG-150919

4-7/8" [124 MM]

INTERIOR

STEEL STUD (NON-LOAD-BEARING)

GYPSUM PANELS:

STEEL STUDS:

INSULATION:

GYPSUM PANELS:

ASSEMBLY REQUIREMENTS:

DESIGN NO. UL U419 - 1 HR FIRE RATING ASSEMBLY - FOR PATCHING ONLY

ONE LAYER 5/8" [15.9 MM] GYPSUM PANEL TYPE X

3-5/8" [92 MM] STEEL STUDS, 16" [406 MM] O.C.

3" [76 MM] FIBERGLASS INSULATION

ONE LAYER 5/8" [15.9 MM] GYPSUM PANEL TYPE X

16" 16" 16"

54321

KEY PLAN

APPROVED BY

CHECKED BY

SHEET NO.

TITLE

DRAWN BY

DATE

PROJECT NO.

SEAL

REVISIONS

P M

UL DESIGN

ASSEMBLY &

PARTITION WALL

08/05/2026

50186890

C M

-M C

R M

G R

E N

O V

A T

R D

F L

O O

B #2

-B

-0

N V

C C

N N

A N

D A

A M

P U

U E

D F

O R

S E

E R

T U

R N

A N

N A

N D

Dewberry Engineering Inc.

8401 ARLINGTON BOULEVARD

FAIRFAX, VA 22031 -4666

703.849.0100

G-005

239 SF

CONF. RM.

111 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

138 SF

FACULTY

OFFICE

126 SF

VESTIBULE

138 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

239 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

310 206 SF

STAIR

301B

122 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

206 SF

STAIR

301A

122 SF

FACULTY

OFFICE

616 SF

CORRIDOR

300A

239 SF

CONF. RM.

111 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

138 SF

FACULTY

OFFICE

126 SF

VESTIBULE

138 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

239 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

310 206 SF

STAIR

301B

122 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

206 SF

STAIR

301A

122 SF

FACULTY

OFFICE

616 SF

CORRIDOR

300A

REMOVE EXISTING FLOOR FINISH

CARPET AND WALL BASE

DEMOLISH THE EXISTING PARTITION

WALL, FULL HEIGHT. REUSE WALL

MOUNTED PROJECTOR SCREENS

E 6' - 2" 11' - 0" 10' - 0" 10' - 6" 12' - 0"

1 1

CUT EXISTING GYP BOARD AT EACH

NEW POWER OUTLET LOCATION TO

ROUTE THE WIRE. COORDINATE

LOCATION WITH ELECTRICAL

DRAWING - TYP.

DEMOLISH EXISTING FIXED

CABINETRY IN ITS ENTIRETY

GROUP

STUDY

787 SF

ORAL

COMMUNICATION

CENTER

544 SF

SELECTIVE EXISTING GYP BOARD

DEMO AT EACH PROJECTION

SCREEN TO INSTALL BLOCKING.

SPECIFIC LOCATION TO BE

COORDINATED WITH OWNER.

REMOVE EXISTING DOOR/

FRAMES & HARDWARS,

COORDINATE W/ NEW

WORK.

REMOVE EXISTING DOOR/

FRAMES & HARDWARS,

COORDINATE W/ NEW

WORK.

SELECTIVE EXISTING GYP BOARD

DEMO AT NEW WHITE BOARD

LOCATION TO INSTALL BLOCKING.

SPECIFIC LOCATION TO BE

COORDINATED WITH OWNER.

DEMOLITION PLAN GENERAL NOTES

1. VISIT SITE AND VERIFY EXISTING CONDITIONS PRIOR TO BID SUBMISSION.

DISCREPANCIES BETWEEN CONSTRUCTION INDICATED ON DRAWINGS AND

ACTUAL SITE CONDITIONS SHALL BE BROUGHT TO ARCHITECT’S ATTENTION

IMMEDIATELY IN WRITING.

2. DEMOLISHED ITEMS NOT INDICATED TO BE “DELIVERED TO OWNER” OR “TO BE

RELOCATED” SHALL BE REMOVED FROM SITE AS SOON AS POSSIBLE UNLESS

THEY ARE TO BE USED FOR REQUIRED PATCHING AND INFILLING OF EXISTING

CONSTRUCTION THAT IS TO REMAIN. NO OTHER DEMOLISHED ITEMS SHALL BE

STORED ON SITE.

3. DEMOLISHED ITEMS NOTED AS “DELIVER TO OWNER” OR “TO BE RELOCATED”

SHALL BE REMOVED OR DISASSEMBLED IN SUCH A MANNER THAT WILL NOT

DAMAGE THE ITEM AND PREVENT IT FROM BEING RELOCATED. REPAIR OR

REPLACE SUCH ITEMS, IF DAMAGED. NOTIFY OWNER’S REPRESENTATIVE

IMMEDIATELY IF DAMAGE HAS OCCURRED, AND SUBMIT A REPAIR SOLUTION TO

ARCHITECT FOR REVIEW.

4. TEMPORARILY STORE ITEMS INDICATED AS “DELIVER TO THE OWNER” IN ONSITE

LOCATION, DESIGNATED BY THE OWNER. OWNER SHALL MOVE ITEM(S), AS

NECESSARY, TO NOT HINDER OR DELAY PERFORMANCE OF WORK IN AREA.

5. TEMPORARILY STORE ITEMS INDICATED AS “TO BE RELOCATED” IN LOCATION

ONSITE AND PROTECT ITEMS FROM DAMAGE PRIOR TO INSTALLATION IN NEW

LOCATION.

6. ITEMS INDICATED “TO REMAIN” THAT ARE DAMAGED DURING THE PERFORMANCE

OF THE DEMOLITION WORK. SUCH DAMAGE SHALL BE REPORTED TO OWNER’S

REPRESENTATIVE IMMEDIATELY, AND SUBMIT A REPAIR SOLUTION TO ARCHITECT

FOR REVIEW.

7. COORDINATE DEMOLITION WORK WITH NEW CONSTRUCTION WORK IN EACH

AREA OF DEMOLITION. EXISTING CONSTRUCTION IN AREAS ADJACENT TO

DEMOLITION WORK SHALL BE PATCHED AND REPAIRED TO MATCH ORIGINAL

EXISTING CONDITION AS REQUIRED TO PROVIDE FOR NEW CONSTRUCTION

WORK IN AREA OF DEMOLITION.

8. ITEMS INDICATED TO BE REMOVED BY OWNER SHALL BE COMPLETED PRIOR TO

COMMENCEMENT OF WORK.

9. AT LOCATIONS WHERE A PORTION OF EXISTING CONSTRUCTION IS TO BE

REMOVED AND PREPARED FOR NEW INFILL CONSTRUCTION, OR AN OPENING IN A

WALL, ROOF, OR FLOOR IS CREATED BY DEMOLITION WORK, CONSTRUCT INFILL

WITH SAME MATERIALS AND METHOD OF CONSTRUCTION AS EXISTING ADJACENT

CONSTRUCTION, UNLESS NOTED OTHERWISE. SEE ARCHITECTURAL DRAWINGS

FOR INFILL CONSTRUCTION. INFILL CONSTRUCTION SHALL SMOOTHLY BUTT

ADJACENT SURFACES AND MATCH THE FINISH, U.N.O.

10. AT LOCATIONS WHERE AN ITEM IS TO BE REMOVED FROM A SURFACE THAT IS TO

REMAIN, PATCH AND REPAIR EXISTING SURFACE TO MATCH EXISTING ADJACENT

SURFACE, UNLESS INDICATED OTHERWISE.

11. EXISTING ITEMS ANCHORED TO CONSTRUCTION THAT IS INDICATED TO BE

DEMOLISHED SHALL BE CONSIDERED A PART OF DEMOLISHED CONSTRUCTION

AND SHALL BE DEMOLISHED WITH THE INDICATED CONSTRUCTION, UNLESS

NOTED OTHERWISE.

12. IN CONDITIONS WHERE A WALL OR FLOOR FINISH IS DEMOLISHED CREATING A

DISSIMILAR ELEVATION IN ADJACENT FLOOR FINISHES, INSTALL AN APPROVED

LEVELING MATERIAL TO BRING LOWER FLOOR FINISH ELEVATION UP TO AN

ELEVATION FLUSH WITH ADJACENT FLOOR.

13. CONSTRUCT TEMPORARY DUST PARTITIONS TO CONTAIN DEMOLITION WORK

AND PREVENT CONSTRUCTION DUST FROM ENTERING ADJACENT EXISTING

CONSTRUCTION. SUBMIT LOCATIONS OF THESE PARTITIONS FOR APPROVAL BY

OWNER’S REPRESENTATIVE. PARTITION LOCATIONS SHALL NOT IMPEDE OR

HINDER EMERGENCY EGRESS FROM BUILDING. REFER TO SPECIFICATIONS FOR

CONSTRUCTION OF DUST PARTITIONS.

14. RETAIN DEMOLISHED MATERIALS AS NEEDED FOR INFILLING OPENINGS IN

EXISTING CONSTRUCTION SO THAT FINISH MATERIALS WILL PROPERLY ALIGN

WITH EXISTING AND MATCH THE EXISTING FINISH. IF DEMOLISHED MATERIALS

ARE NOT SALVAGEABLE, NOTIFY OWNER’S REPRESENTATIVE, SO THAT

ALTERNATE SOLUTIONS MAY BE DETERMINED.

15. IF EXISTING CONSTRUCTION IS REVEALED NOT CONSTRUCTED OR FINISHED IN A

MANNER THAT MATCHES ADJACENT SURFACES, PATCH AREA AS NECESSARY

WITH APPROPRIATE MATERIALS AND METHODS OF CONSTRUCTION TO MATCH

EXISTING ADJACENT FINISH, OR PREPARE SURFACE FOR INSTALLATION OF NEW

FINISH. CONTACT OWNER’S REPRESENTATIVE AS SOON AS POSSIBLE SO THAT

CONCEALED CONSTRUCTION MAY BE IDENTIFIED AND SCOPE OF POSSIBLE

ADDITIONAL WORK DETERMINED.

16. WHEN EXISTING SURFACE IS INDICATED TO BE “PATCHED AND REPAIRED” OR

“PREPARED” TO RECEIVE NEW FINISH MATERIAL, PROVIDE A CONSTRUCTION

SURFACE THAT IS CAPABLE OF RECEIVING NEW FINISH MATERIAL.

17. WHEN THE TERM ‘ENTIRETY’ IS DIRECTED TO A SPECIFIC ITEM OR ASSEMBLY,

DEMOLISH AND REMOVE IDENTIFIED ITEM AND ASSOCIATED CONSTRUCTION

PERTINENT TO THE ITEM, INCLUDING, BUT NOT LIMITED TO UNDERGROUND AND

CONCEALED CONSTRUCTION, SUCH AS FOOTINGS AND FOUNDATIONS, SEWER,

PLUMBING, AND ELECTRICAL WORK. THIS DEMOLITION WORK SHALL BE

COORDINATED WITH THE CIVIL, STRUCTURAL, PLUMBING, MECHANICAL,

ELECTRICAL, AND TECHNOLOGY DRAWINGS.

18. CONTRACTOR TO PROVIDE HOURLY FIRE WATCH FOR ANY FIRE ALARM OR

SPRINKLER IMPAIRMENTS 1-HOUR OR LONGER. FIRE WATCH TO INCLUDE

WALKING THE ENTIRE BUILDING HOURS. FIRE WATCH TO BE DOCUMENTED ON A

FIRE WATCH LOG. PROVIDE THE FIRE WATCH LOG TO THE PROJECT MANAGER.

REMOVE CEILING TILES

AND GRIDS AFFECTED

BY THE DEMOLITION

EX. ACP

10' - 0"

COMPUTER

CLASS RM

MOVE EXISTING CEILING

PROJECTOR TO THE NEW

LOCATION - COORDINATE

WITH THE OWNER FOR

THE EXACT LOCATION

MOVE EXISTING CEILING

PROJECTOR TO THE NEW

LOCATION - COORDINATE

WITH THE OWNER FOR

THE EXACT LOCATION

EXISTING SPRINKLER

HEAD TO REMINA - TYP.

LEGEND - DEMOLITION PLAN

EXISTING WALL TO REMAIN

EXISTING DOOR AND FRAME TO DEMOLISH

EXISTING WALL TO DEMOLISH

EXISTING DOOR TO NOT IN THE SCOPE

WORK NOT INCLUDED IN THE SCOPE

EXISTING CEILING PANEL TO DEMOLISH

54321

KEY PLAN

APPROVED BY

CHECKED BY

SHEET NO.

TITLE

DRAWN BY

DATE

PROJECT NO.

SEAL

REVISIONS

P M

THIRD FLOOR

DEMO WORK

PLAN

08/05/2026

50186890

C M

-M C

R M

G R

E N

O V

A T

R D

F L

O O

B #2

-B

-0

N V

C C

N N

A N

D A

A M

P U

U E

D F

O R

S E

E R

T U

R N

A N

N A

N D

Dewberry Engineering Inc.

8401 ARLINGTON BOULEVARD

FAIRFAX, VA 22031 -4666

703.849.0100

A-1110' 4' 8'2'

SCALE: 1/4" = 1' - 0"

NORTH

Scale: 1/8" = 1'-0"1 THIRD FLOOR - DEMO WORK PLAN

NO. DESCRIPTION DATE

Scale: 1/8" = 1'-0"2 3RD FLOOR - DEMO WORK RCP

111 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

138 SF

FACULTY

OFFICE

126 SF

VESTIBULE

138 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

239 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

310 206 SF

STAIR

301B

122 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

206 SF

STAIR

301A

122 SF

FACULTY

OFFICE

616 SF

CORRIDOR

300A

239 SF

CONF. RM.

111 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

138 SF

FACULTY

OFFICE

126 SF

VESTIBULE

138 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

239 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

310 206 SF

STAIR

301B

122 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

206 SF

STAIR

301A

122 SF

FACULTY

OFFICE

616 SF

CORRIDOR

300A

REPLACE CEILING TILES AND

GRIDS AFFECTED BY THE

PARTITION WALL DEMOLITION -

COLOR & MATERIAL TO MATCH

EXISTING CEILING

EX. ACP

10' - 0"

RELOCATE EXISTING CEILING

MOUNTED POWER OUTLET AND

PROJECTOR. COORDINATE W/

OWNER FOR EXACT LOCATION

RELOCATE EXISTING CEILING

MOUNTED POWER OUTLET AND

PROJECTOR. COORDINATE W/

OWNER FOR EXACT LOCATION

PROVIDE CEILING MOUTED

RECEPTACLE - SEE ELECTRICAL

DWGS. COORDINATE W/ OWNER

FOR EXACT LOCATION - TYP

PROVIDE CEILING MOUTED

RECEPTACLE - SEE ELECTRICAL

DWGS. COORDINATE W/ OWNER

FOR EXACT LOCATION - TYP

RECESSED LIGHT

FIXTURE

PENDANT FIXTURE

SUPPLY DIFFUSER

RETURN DIFFUSER

EXIT SIGN

S SPEAKER

A FIRE ALARM

HEAT DETECTOR

SMOKE DETECTOR

LINEAR SLOT DIFFUSER

EXISTING SPRINKLER

HEAD

EMERGENCY LIGHT

RECESSED LIGHT

FIXTURE

CEILING LEGEND

EXISTING SUSPENDED

ACOUSTICAL PANEL

CEILING TO REMAIN

CEILING MOUNTED PROJECTOR

CEILING OR WALL MOUNTED

MOTORIZED PROJECTION

SCREEN

SURFACE MOUNTED

LIGHT FIXTURE

STRIP FIXTURE

TRACK LIGHTING

HORN/STROBE DEVICE

EXHAUST AIR DEVICE

OCCUPANCY SENSOR

CELING MOUNTED

POWER OUTLET -

DUPLEX

s SPEAKER/STROBE

STROBE

NOTE: FOR MEPFP DEVICES, REFER TO MEPFP DRAWINGS.

APC-X

8' - 0"

CEILING TYPE

CEILING HEIGHT

NEW SUSPENDED ACOUSTICAL

PANEL CEILING

CELING MOUNTED

POWER OUTLET -

QUADRUPLEX

GENERAL NOTES - NEW WORK PLAN

1. DIMENSIONS ARE SHOWN AS FOLLOWS, U.N.O.

A. ALL DIMENSIONS ARE SHOWN TO THE FINISHED FACE, U.N.O.

B. DIMENSIONS NOTED AS "CLEAR" (CLR.) ARE TO THE FACE OF FINISHED

SURFACE AND TAKE PRECEDENT OVER ALL OTHER DIMENSIONS.

C. DISCREPANCIES IN DIMENSIONS SHALL BE IMMEDIATELY BROUGHT TO THE

ATTENTION OF THE ARCHITECT, WHO WILL ISSUE WRITTEN CLARIFICATION.

2. FINAL WALL PREP REQUIREMENTS ARE BASED ON OWNER SELECTION FINISH

AND WITH THE SPECIFICATIONS.

3. BACK-TO-BACK OUTLETS CANNOT OCCUPY SAME STUD CAVITY SPACE. IN

ACOUSTICALLY TREATED WALLS, PROVIDE ACOUSTIC PUTTY PADS AROUND

OUTLET BOXES.

4. REFER TO G-003 LIFE SAFETY & CODE PLANS ANALYSIS AND LOCATION OF

FIRE RATED WALLS .

5. REFER TO SHEET G-004 FOR FIRE-RATED UL WALL PENETRATIONS AND

ASSEMBLY NUMBERS.

USE TYPE X, FIRE RATED

GYP BOARD TO PATCH &

FINISH ALL WALL

PENETRATIONS AND GAP

W/ FIRE SEAL INCLUDING

TOP AND BOTTOM OF

THE WALL JOINTS.

6' - 2" 11' - 0" 10' - 0" 10' - 6" 12' - 0"

COMPUTER

CLASS RM

INSTALL NEW DOOR/ FRAME W/

ELECTRONIC DOOR ACCESS

(EDA). SEE A-201 FOR DOOR

SCHEDULE AND SPEC 08 71 00

INSTALL NEW DOOR/ FRAME W/

ELECTRONIC DOOR ACCESS

(EDA). SEE A-201 FOR DOOR

SCHEDULE AND SPEC 08 71 00

PROVIDE BLOCKING AS

REQUIRED TO RELOCATE

EXISTING WALL

MOUNTED PROJECTOR.

EXACT LOCATION TO BE

COORDINATED WITH

OWNER.

PROVIDE WHIEBOARD - SIZE

TO BE SELECTED BY OWNER.

PROVIDE BLOCKING AS

REQUIRED.

PROVIDE BLOCKING AS

REQUIRED TO RELOCATE

EXISTING WALL

MOUNTED PROJECTOR.

EXACT LOCATION TO BE

COORDINATED WITH

OWNER.

USE SIMILAR GYP BOARD

AS THE EXISTING WALL

TO PATCH & FINISH ALL

WALL PENETRATIONS

AND GAP W/ ACOUSTICAL

SEAL INCLUDING TOP

AND BOTTOM OF THE

WALL JOINTS.

311B

311A

54321

KEY PLAN

APPROVED BY

CHECKED BY

SHEET NO.

TITLE

DRAWN BY

DATE

PROJECT NO.

SEAL

REVISIONS

P M

THIRD FLOOR

NEW WORK PLAN

08/05/2026

50186890

C M

-M C

R M

G R

E N

O V

A T

R D

F L

O O

B #2

-B

-0

N V

C C

N N

A N

D A

A M

P U

U E

D F

O R

S E

E R

T U

R N

A N

N A

N D

Dewberry Engineering Inc.

8401 ARLINGTON BOULEVARD

FAIRFAX, VA 22031 -4666

703.849.0100

A-112Scale: 1/8" = 1'-0"2 3RD FLOOR - NEW WORK RCP

0' 4' 8'2'

SCALE: 1/4" = 1' - 0"

NORTH

NO. DESCRIPTION DATE

Scale: 1/8" = 1'-0"1 THIRD FLOOR - NEW WORK PLAN

111 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

138 SF

FACULTY

OFFICE

126 SF

VESTIBULE

138 SF

FACULTY

OFFICE

106 SF

FACULTY

OFFICE

111 SF

FACULTY

OFFICE

239 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

310 206 SF

STAIR

301B

122 SF

FACULTY

OFFICE

122 SF

FACULTY

OFFICE

206 SF

STAIR

301A

122 SF

FACULTY

OFFICE

616 SF

CORRIDOR

300A

6' - 2" 11' - 0" 10' - 0" 10' - 6" 12' - 0"

PNT-1

VCB

CPT

COMPUTER

CLASS RM

SH-1 TA-1

SH-1

CH-1 (TYP)

(TYP)

H E

WIDTH

* 6" 6"

D O

O R

H E

WIDTH

DOOR

5/16" THICK CLEAR,

45 MINUTES FIRE RATED,

SAFETY RATED GLASS

PT-X

RB-X

CPT-X

NOTES: 22

ROOM NAME

INTERIOR FINISH LEGEND

ROOM FINISH TAG

WALL FINISH

BASE FINISH

FLOOR FINISH

NOTES

(IF APPLICABLE)

ACCENT WALL MATERIAL / COLOR

XXX

FINISH AND FURNITURE PLAN GENERAL NOTES

1. FINISH INDICATES ENTIRE SURFACE, U.N.O.

2. SEE FINISH SCHEDULE FOR FINISH DETAILS.

3. ALL FURNITURE (CHAIRS & TABLES) ARE OWNER FURNISHER / OWNER

INSTALLED

1/2"1/2"

VARIES

SEALANT ALL AROUND,

BOTH SIDES

HOLLOW METAL FRAME

PARTITION AS SCHEDULED

DOOR AS SCHEDULED

V A

PARTITION AS SCHEDULED

HOLLOW METAL FRAME

JAMB ANCHOR CLIP

DOOR AS SCHEDULED

SEALANT ALL AROUND,

BOTH SIDES

DOOR

CONCRETE SLAB

MAT-1

EXISTING LVT-1

SCHLUTER SCHIENE,

BRUSHED STAINLESS STEEL

V2A, 3MM (1/8")

M A

HOLLOW METAL DOOR & GLAZING GENERAL NOTES:

1. DOOR ASSEMBLY TO BE A 45-MINUTE FIRE-PROTECTION-RATED, MINIMUM 18-

GAUGE HOLLOW METAL DOOR INSTALLED IN A 1-HOUR FIRE-RATED CORRIDOR

WALL ASSEMBLY. DOOR AND FRAME TO BEAR COMPLIANT UL/WHI IDENTIFICATION

LABELS PER VCC TABLE 716.1(2).

2. PROVIDE 45-MINUTE FIRE-PROTECTION AND IMPACT SAFETY-RATED GLAZING (5/16"

NOMINAL THICKNESS, 6" X 36" VISIBLE AREA) FIELD-INSTALLED IN THE FACTORY-

PREPARED CUTOUT.

3. GLAZING TO BE ETCHED WITH PERMANENT CERTIFICATION MARKINGS COMPLYING

WITH VCC CHAPTERS 7 & 24, INCLUDING "D-H-45" (VCC TABLE 716.1(1)) AND CPSC 16

CFR 1201 CAT. II / ANSI Z97.1 FOR HAZARDOUS DOOR LOCATIONS.

4. GLAZING ENCLOSURE KIT MUST BE A LISTED 18-GAUGE STEEL, SELF-CORING/BOLT-

THROUGH VISION FRAME KIT IN ACCORDANCE WITH NFPA 80 WITH APPROVED

INTUMESCENT GLAZING TAPE.

54321

KEY PLAN

APPROVED BY

CHECKED BY

SHEET NO.

TITLE

DRAWN BY

DATE

PROJECT NO.

SEAL

REVISIONS

P M

FINISH/

FURNITURE PLAN

& DOOR

SCHEDULE

08/05/2026

50186890

C M

-M C

R M

G R

E N

O V

A T

R D

F L

O O

B #2

-B

-0

N V

C C

N N

A N

D A

A M

P U

U E

D F

O R

S E

E R

T U

R N

A N

N A

N D

Dewberry Engineering Inc.

8401 ARLINGTON BOULEVARD

FAIRFAX, VA 22031 -4666

703.849.0100

A-201Scale: 1/8" = 1'-0"1 THIRD FLOOR - NEW FINISH & FURNITURE PLAN

NO. DESCRIPTION DATE

DOOR SCHEDULE

D O

O R

N U

M B

R DOOR FRAME DETAILS

E L

A B

E L

H A

R D

W A

R E

M A

R K

D O

O R

N U

M B

E R

F Q

T Y

SIZE

T Y

P E

M A

T E

T Y

P E

M A

T E

SIDELIGHT

WIDTH

TRANSOM

HEIGHT HEAD JAMB SILLWIDTH

WIDTH

(IF

UNEVEN) HEIGHT THICKNESS

311A 1 3' - 0" 7' - 0" 1 3/4" N HM 01 HM H-1 J-1 S-1 45 minutes 01 311A 311B 1 3' - 0" 7' - 0" 1 3/4" N HM 01 HM H-1 J-1 S-1 45 minutes 01 311B

Scale: 1/4" = 1'-0"3 DOOR PANEL & FRAME TYPES

COMUPTER CLASS ROOM - 311 - FINISH SCHEDULE

MATERIAL TYPE FINISH DESCRIPTIONS

BASE FINISHES

VINYLE BASES VCB JOHNSONITE - JOHNSONITE - 38 PEWTER CG

CEILING FINISHES

ACOUSTIC CEILING TILE (ACT) ACT-1 MATCH EXISTING CEILING TILES SIZE, COLOR AND TEXTURE

FLOOR FINISHES

CARPET TILE (CPT) CPT-1 J&J FLOORING JOURNEY - 3352 GREEN LEAD - 18" x 32" MODULAR TILE

WALL FINISHES

PAINT (PNT) PNT-1 SHERWIN WILLIAMS - SW 7035 - AESTHETIC WHITE EGG SHELL FINISH

PAINT (PNT) PNT-2 (ACCENT WALL) SHERWIN WILLIAMS - SW 6460 - KALE GREEN EGGE SHELL FINISH PAINT (PNT) PNT-3 (DOOR FRAME PAINTS) SHERWIN WILLIAMS - SW 9162 AFRICAN GRAY - SEMI GLSOSS FINISH

FURNITURE SCHEDULE & RESPONSIBILITY MATRIX

FURNITURE

TAG DESCRIPTION RESPONSIBILITY

CH-1 CHAIR OWNER FURNISHED - OWNER INSTALLED

SH-1 SHELF OWNER FURNISHED - OWNER INSTALLED

TA-1 TABLE OWNER FURNISHED - OWNER INSTALLED

Scale: 1 1/2" = 1'-0"4 H-1 DOOR HEAD

Scale: 1 1/2" = 1'-0"5 J-1 DOOR JAMB

Scale: 6" = 1'-0"6 S-1 - CARPET TO VCT

HARDWARE NOTE: THE HARDWARE MUST PROVIDE FREE MECHANICAL EGRESS AT ALL TIMES.

A101

SIM

FIRST FLOOR

100' - 0"

A101

SIM

Scale:1 View Name 1/8" = 1'-0"

CALLOUT

BUILDING/WALL

SECTION

ROOM TAG

REVISION TAG

KEYNOTE TAG

(PER SHEET NUMBERS)

AREA TO BE

ENLARGED SHEET REF.

PLAN / DETAIL

REF.

SECTION REF.

SHEET REF.

LEVEL LINE

ROOM NUMBER

VIEW NAME

VIEW SCALE

VIEW DESIGNATION VIEW TITLE

LEVEL NAME

LEVEL

ELEVATION

GRID LINE

NORTH INDICATOR

GRID NUMBER OR

LETTER

INDICATES

PLAN NORTH

INDICATES

TRUE NORTH

SPOT ELEVATION

SYMBOL

REVISION NUMBER

REVISION CLOUD

POINT OF

CONNECTION

1' - 0"ELEVATION AT

POINT INDICATED

POINT OF

DISCONNECTION

STANDARD DETAILING SYMBOLS

EXISTING

DEMOLITION

NEW

FUTURE

BACKGROUND

HIDDEN/UNDER

OBSTRUCTION

Space Name

SYMBOL DESCRIPTION

LINETYPES

FLEXIBLE CONNECTOR

SUPPLY SQUARE CEILING DIFFUSER

(4-WAY DISCHARGE UNLESS INDICATED OTHERWISE)

RETURN SQUARE CEILING DIFFUSER

RETURN DUCT VIEW INTO DUCT

DUCTWORK TO DROP IN ELEVATION

DUCTWORK TO RISE IN ELEVATION

RETURN DUCT VIEW HEEL OF ELBOW

SUPPLY DUCT VIEW HEEL OF ELBOW

FLEXIBLE DUCTWORK

SYMBOL

SUPPLY DUCT VIEW INTO DUCT

DUCTWORK & SIZE

EXTRACTOR WITH ADJUSTABLE OPERATOR

SPLITTER DAMPER

TURNING VANES AT MITERED ELBOW

AUTOMATIC DAMPER (MOTORIZED)

FIRE & SMOKE DAMPER (MOTORIZED)

DESCRIPTION

AUTOMATIC FIRE DAMPER (MOTORIZED)

MANUAL DAMPER

LINEAR DIFFUSER WITH PLENUM ON TOP

FIRE DAMPER FD

SMOKE DAMPER (MOTORIZED)

BACKDRAFT DAMPER

DAMPER

EXHAUST DUCT VIEW INTO DUCT

EXHAUST DUCT VIEW HEEL OF ELBOW

EXHAUST SQUARE CEILING DIFFUSER

PLENUM SLOT DIFFUSER

SYMBOL DESCRIPTION

PRESSURE RELIEF VALVE

AUTOMATIC AIR VENT

PIPE ELBOW DOWN

DIRECTION OF FLOW

PIPE ELBOW UP

GAUGE COCK

2-WAY AUTOMATIC CONTROL VALVE (MOTORIZED)

HOSE END DRAIN VALVE WITH CAP

BALANCING VALVE

THERMOMETER AND WELL

PIPE TOP TAKE OFF

PIPE BOTTOM TAKE OFF

UNION

CHECK VALVE (DIRECTION OF FLOW INDICATED)

PIPE CONTINUES

PIPE SLEEVE

PIPE CAP OR PLUG

FLANGE

PRESSURE & TEMPERATURE TEST PLUG

PRESSURE GAUGE

STOP VALVE

BACKFLOW PREVENTER

3-WAY AUTOMATIC CONTROL VALVE (MOTORIZED)

VENTURI FLOW TUBE

Y-TYPE STRAINER

BASKET TYPE STRAINER

FLEXIBLE CONNECTION

SOLENOID VALVE

PRESSURE REGULATING VALVE

REDUCER (CONCENTRIC)

REDUCER (ECCENTRIC)

PRESSURE REDUCING VALVE

WATER METER

SUPPLY ROUND CEILING DIFFUSER

HVAC SYMBOLS MECHANICAL PIPING SYMBOLS

THERMOSTAT

HUMIDISTAT

CARBON DIOXIDE SENSOR

CARBON MONOXIDE SENSOR

NITROGEN DIOXIDE SENSOR

SIDEWALL SUPPLY REGISTER OR GRILLE

SIDEWALL RETURN/EXHAUST REGISTER OR GRILLE

THE FOLLOWING SCHEDULE SHALL BE USED BY THE

CONTRACTOR FOR ROUND TO FLAT OVAL DUCTWORK SIZE

EQUIVALENTS UNLESS NOTED OTHERWISE.

ROUND DIAMETER (IN) EQUIVALENT FLAT OVAL (IN - H x W)

3 x 11, 4 x 9, 5 x 8

4 x 15, 5 x 12, 6 x 11

6 x 15, 7 x 13, 8 x 11, 9 x 12

7 x 20, 8 x 17, 9 x 15, 10 x 13

9 x 20, 10 x 18, 11 x 17, 12 x 15

FLAT OVAL DUCTWORK SCHEDULE

FLEXIBLE AND RIGID ROUND BRANCH DUCTWORK FOR DIFFUSER TAKE-OFFS

OR RUNOUTS SHALL BE SIZED IN ACCORDANCE WITH THE FOLLOWING

SCHEDULE UNLESS NOTED OTHERWISE ON FLOOR PLANS.

WHERE THE DEPTH OF THE DUCTWORK WILL NOT PERMIT A ROUND SPIN

COLLAR FITTING, PROVIDE AN EQUIVALENT FLAT OVAL CONNECTION WITH

MANUAL VOLUME DAMPER AND AN OVAL TO ROUND TRANSITION FOR EACH

TAP. SEE FLAT OVAL DUCTWORK SCHEDULE FOR EQUIVALENT FLAT OVAL

SIZES. THIS SCHEDULE DOES NOT APPLY FOR DUCTWORK SERVING

PERIMETER SLOT DIFFUSERS SD-A AND SD-B. REFER TO FLOOR PLANS FOR

ADDITIONAL INFORMATION.

0 - 150

151 - 250

251 - 350

351 - 550

551 - 700

AIRFLOW (CFM) ROUND DIAMETER (IN)

ROUND BRANCH DUCTWORK SCHEDULE

12x12

DUCT ACCESS DOOR (ON BOTTOM)

DUCT ACCESS DOOR (ON SIDE)

10.

11.

12.

REFER TO RISER AND SCHEMATIC DIAGRAMS FOR PIPE SIZES, DUCT

SIZES, AND AIRFLOWS NOT INDICATED ON THE FLOOR PLANS.

THROUGH-PENETRATION FIRESTOP MATERIAL SHALL BE TESTED,

MANUFACTURED AND INSTALLED IN ACCORDANCE WITH UL 1479.

IN ACCORDANCE WITH MECHANICAL CODE, ALL PRODUCTS,

COMPONENTS, MATERIALS AND COMPOSITE MATERIALS WITHIN

SUPPLY, RETURN, EXHAUST, RELIEF AND VENTILATION AIR PLENUMS

SHALL BE NON-COMBUSTIBLE OR SHALL BE LISTED/CLASSIFIED AND

LABELED AS HAVING A FLAME SPREAD INDEX OF NOT MORE THAN 25

AND A SMOKE DEVELOPED INDEX OF NOT MORE THAN 50 WHEN

TESTED IN ACCORDANCE WITH ASTM E84 OR UL 723.

ALL DUCT DIMENSIONS SHOWN ARE INSIDE DIMENSIONS. REFER TO

SPECIFICATIONS FOR INTERNALLY INSULATED/LINED DUCTWORK

REQUIREMENTS.

ALL DUCTWORK AND PIPING SHALL BE TIGHT TO BOTTOM OF

STRUCTURE UNLESS OTHERWISE INDICATED.

REFER TO THE ARCHITECTURAL DRAWINGS FOR THE EXACT LOCATION

AND SIZE OF ALL WALL OR FLOOR OPENINGS.

VALVES, JUNCTION BOXES, CLEAN-OUTS, FUTURE CONNECTIONS AND

OTHER ITEMS THAT WILL REQUIRE ACCESS PANELS IN DRYWALL

CEILINGS SHALL NOT BE LOCATED WITHIN THE MAIN LOBBY AND

ELEVATOR LOBBIES. DUCTWORK, PIPING, WIRING AND ETC. SHALL NOT

BLOCK ACCESS TO JUNCTION BOXES, VALVES AND CLEAN-OUTS.

REFER TO ARCHITECTURAL DRAWINGS FOR LOCATION OF ALL VISIBLE

CEILING AND WALL MOUNTED DEVICES.

THE EXISTING MECHANICAL, ELECTRICAL, AND PLUMBING SYSTEMS

AND ASSOCIATED MATERIALS OF CONSTRUCTION HAVE BEEN

PREVIOUSLY APPROVED BY THE MECHANICAL, ELECTRICAL, PLUMBING

DIVISIONS AND FIRE MARSHAL'S OFFICE OF THE LOCAL CODE

AUTHORITIES HAVING JURISDICTION. EXISTING SPECIFICATIONS AND

MATERIALS OF CONSTRUCTION APPLY TO ALL WORK SHOWN ON THE

DRAWINGS UNLESS OTHERWISE NOTED.

RETURN AIR SYSTEM: THE RETURN AIR SYSTEM CONSISTS OF A

CONTINUOUS PLENUM COMMON TO ALL AREAS WITHIN THE LEASE

SPACE. AIR IS RETURNED FROM THE SPACE INTO THE PLENUM

THROUGH RETURN AIR GRILLES AND HEAT EXTRACT LIGHT FIXTURES

DESIGNED FOR RETURN AIR APPLICATION.

RETURN AIR SYSTEM: THE RETURN AIR SYSTEM CONSISTS OF A

DUCTED SYSTEM TO ALL AREAS WITHIN THE LEASE SPACE. AIR IS

RETURNED FROM THE SPACE INTO THE DUCTWORK THROUGH RETURN

AIR GRILLES.

OUTDOOR AIR SYSTEM: OUTDOOR AIR IS PROVIDED TO EACH

FLOOR/SYSTEM THROUGH A SUPPLY TAP LOCATED WITHIN THE AIR

HANDLING UNIT ROOM. FROM THIS POINT, THE OUTDOOR AIR IS

EQUITABLY DISTRIBUTED THROUGHOUT THE SPACE THROUGH THE

SUPPLY DUCTWORK SYSTEM. REFER TO DRAWINGS FOR VENTILATION

CALCULATIONS AND OUTDOOR AIR PROVIDED FOR EACH SYSTEM.

FLOW METER

ABBREVIATIONS GENERAL NOTES

FLOW SWITCHFS

TEMPERATURE SENSORTS

MECHANICAL SYSTEMS SHALL BE DESIGNED AND INSTALLED IN

ACCORDANCE WITH THE FOLLOWING CODES.

2021 VIRGINIA MECHANICAL CODE

2021 VIRGINIA CONSTRUCTION CODE

2021 VIRGINIA ENERGY CONSERVATION CODE

2021 VIRGINIA FUEL GAS CODE

2021 VIRGINIA STATEWIDE FIRE PREVENTION CODE

2021 VIRGINIA FUEL GAS CODE

CODES

CARBON MONOXIDE AND NITROGEN DIOXIDE SENSORCN

54321

KEY PLAN

APPROVED BY

CHECKED BY

SHEET NO.

TITLE

DRAWN BY

DATE

PROJECT NO.

SEAL

REVISIONS

8/ 5/

P M

MECHANICAL

SYMBOLS,

LEGEND, NOTES

JS/MN

08/05/26

50186890

C M

-M C

R M

G R

D F

0- B4

L2 4N

O R

U R

E, V

M-001

DRAWING LIST - MECHANICAL

M-001 MECHANICAL SYMBOLS, LEGEND, NOTES

M-111 MECHANICAL THIRD FLOOR NEW WORK PLAN

TOTAL: 2

AC AIR CONDITIONING

AD ACCESS DOOR

ADJ ADJUSTABLE

AF AIRFLOW

AFF ABOVE FINISHED FLOOR

AHU AIR HANDLING UNIT

AI ANALOG INPUT

AO ANALOG OUTPUT

ARCH ARCHITECTURAL

AS AIR SEPARATOR

ASHRAE AMERICAN SOCIETY OF HEATING,

REFRIGERATING, AND AIR-CONDITIONING

ENGINEERS

ATC AUTOMATIC TEMPERATURE CONTROL

ATV ATMOSPHERIC VENT

B BOILER

BAS BUILDING AUTOMATION SYSTEM

BBD BOILER BLOWDOWN

BHP BRAKE HORSEPOWER

BI BINARY INPUT

BMS BUILDING MANAGEMENT SYSTEM

BO BINARY OUTPUT

BT BUFFER TANK

BTU BRITISH THERMAL UNIT

BTUH BRITISH THERMAL UNIT PER HOUR

CD CONDENSATE DRAIN

CF CHEMICAL FEEDER

CFM CUBIC FEET PER MINUTE

CH CHILLER

CHWP CHILLED WATER PUMP

CO2, CD CARBON DIOXIDE

CO, CM CARBON MONOXIDE

CONT CONTROLS, CONTINUED

CRU CONDENSATE RETURN UNIT

CT COOLING TOWER

CU CONDENSING UNIT

CUH CABINET UNIT HEATER

Cv VALVE COEFFICIENT

CWP CONDENSER WATER PUMP

DB DRY BULB

DBL DOUBLE

DEG DEGREE

DI DIGITAL INPUT

DIA DIAMETER

DMSS DUCTLESS MINI-SPLIT SYSTEM

DN DOWN

DO DIGITAL OUTPUT

DOAS DEDICATED OUTDOOR AIR SYSTEM

DP DIFFERENTIAL PRESSURE (SENSOR)

DP DEW POINT

DRE DRYER EXHAUST

DWG DRAWING

DWH DOMESTIC WATER HEATER

DX DIRECT EXPANSION

EA EXHAUST AIR

EAT ENTERING AIR TEMPERATURE

ECM ELECTRONICALLY COMMUTATED MOTOR

EF EXHAUST FAN

EHC ELECTRIC HEATING COIL

ELEC ELECTRICAL

EMCS ENVIRONMENTAL MANAGEMENT CONTROL

SYSTEM

ESP EXTERNAL STATIC PRESSURE

ET EXPANSION TANK

ETC ETCETERA

EUH ELECTRIC UNIT HEATER

EWH ELECTRIC WATER HEATER

EWT ENTERING WATER TEMPERATURE

F DEGREES FAHRENHEIT

FD FIRE DAMPER OR FLOOR DRAIN

FLA FULL LOAD AMPS

FLEX FLEXIBLE

FP FAN POWERED

FPM FEET PER MINUTE

FPTD FAN POWERED TERMINAL DEVICE

FS FLOW SWITCH

FT FOOT/FEET

GA GAUGE

GAL GALLONS

GALV GALVANIZED

GC GENERAL CONTRACTOR

GPH GALLONS PER HOUR

GPM GALLONS PER MINUTE

GR GRAINS

GUH GAS FIRED UNIT HEATER

H HUMIDIFIER OR HEIGHT

H2O WATER

HD HEAD

HP HORSEPOWER

HVAC HEATING, VENTILATION, AND

AIR-CONDITIONING

HWT HEATING WATER TEMPERATURE

HX HEAT EXCHANGER

IN INCH

KEF KITCHEN EXHAUST FAN

KW KILOWATT

L LOUVER

LAT LEAVING AIR TEMPERATURE

LBS POUNDS

LF LINEAR FEET

LWT LEAVING WATER TEMPERATURE

M MOTOR OR MOTORIZED DAMPER OR METER

MA MIXED AIR

MAT MIXED AIR TEMPERATURE

MAU MAKEUP AIR UNIT

MBH 1,000 BRITISH THERMAL UNITS PER HOUR

MCA MINIMUM CIRCUIT AMPS

MERV MINIMUM EFFICIENCY REPORTING VALUE

MFR MANUFACTURER

MOCP MAXIMUM OVERCURRENT PROTECTION

NC NORMALLY CLOSED OR NOISE CRITERIA

NO NORMALLY OPEN OR NUMBER

NPSH NET POSITIVE SUCTION HEAD

NTS NOT TO SCALE

OA OUTDOOR AIR

OAT OUTDOOR AIR TEMPERATURE

OD OUTSIDE DIAMETER

OS OCCUPANCY SENSOR

P PRESSURE OR PRESSURE SENSOR

PD PRESSURE DROP

PH PHASE

PHC PREHEAT COIL

PICV PRESSURE INDEPENDENT CONTROL VALVE

PPM PARTS PER MILLION

PRV PRESSURE REDUCING VALVE

PSI POUNDS PER SQUARE INCH

PSIA POUNDS PER SQUARE INCH ABSOLUTE

PSIG POUNDS PER SQUARE INCH GAUGE

PTAC PACKAGED TERMINAL AIR CONDITIONER

QTY QUANTITY

R RADIUS, RISE, OR REMOVE

RA RETURN AIR

RAT RETURN AIR TEMPERATURE

RCP REFLECTED CEILING PLAN

REF RELIEF AIR FAN

RF RETURN AIR FAN

RH RELATIVE HUMIDITY, REHEAT

RHC REHEAT COIL

RPM REVOLUTIONS PER MINUTE

RTU ROOF TOP UNIT

SA SUPPLY AIR

SAT SUPPLY AIR TEMPERATURE

SCH SCHEDULE

SEC SECONDS

SF SUPPLY FAN OR SQUARE FOOT

SF SUPPLY AIR FAN

SP STATIC PRESSURE

SS SPLIT SYSTEM OR STAINLESS STEEL

T&P TEMPERATURE AND PRESSURE

T, TEMP TEMPERATURE

T-STAT THERMOSTAT

TON COOLING TONS (12,000 BTUH)

TSP TOTAL STATIC PRESSURE

TYP TYPICAL

UH UNIT HEATER

V, VOLT VOLTAGE

VAV VARIABLE AIR VOLUME

VEL VELOCITY

VF VENTILATION FAN

VFD VARIABLE FREQUENCY DRIVE

W WIDTH OR WATTS

W/ WITH

WB WET BULB

WC WATER COLUMN

WG WATER GAUGE

WPD WATER PRESSURE DROP

WSHP WATER-SOURCE HEAT PUMP

NO. DESCRIPTION DATE

EDC

14x8

10x8 6x6

6x6

10x8

22x6

12x8

22x6

18/12ø

20x10

14/8ø

18x10

20x10 20x12

26/14ø20/14ø

FPT-3-37 (E)

FPT-3-6 (E)

COMPUTER CLASS

130 130

130130

130135

3/4" HWR

3/4" HWS

3/4" HWR

14x6

NOTES:

THE TERMINAL UNIT DESIGNATION, FAN AIRFLOW SET POINTS, AND HOT WATER FLOW RATE (GPM) SHALL BE AS

INDICATED ON THE DRAWINGS.

REFER TO SPECIFICATIONS FOR ADDITIONAL REQUIREMENTS, INCLUDING BUT NOT LIMITED TO, REQUIREMENTS FOR SHOP DRAWING SUBMITTAL DATA. SUBMITTAL DATA MUST LIST EACH UNIT BY THE ZONE DESIGNATION

SHOWN ON THE DRAWINGS.

THE MAXIMUM PRIMARY AIR VOLUME SET POINT SHALL BE 88.1% OF THE FAN AIRFLOW SET POINT INDICATED ON THE FLOOR PLANS. THE MINIMUM PRIMARY AIRFLOW SET POINT SHALL BE 16% OF THE MAXIMUM PRIMARY

AIRFLOW SET POINT.

INLET SIZE INDICATED FOR TERMINAL UNITS IS FOR ROUND OR ROUND EQUIVALENT FLAT OVAL CONNECTION.

SIZE OF INLET DUCTWORK SHALL MATCH THE INLET SIZE OF THE TERMINAL UNIT UNLESS OTHERWISE INDICATED. TERMINAL UNIT MANUFACTURER SHALL MAKE RECOMMENDATIONS CONCERNING THE ADJUSTMENT OF INLET SIZES BASED ON OPTIMIZING AND IMPROVING THE COMBINATION OF PERFORMANCE FACTORS INCLUDING BUT NOT LIMITED TO CONTROLLABILITY OF MINIMUM AND MAXIMUM PRIMARY AIRFLOW SET POINTS AND ACOUSTICS. INLET SIZE ADJUSTMENTS BASED ON THESE RECOMMENDATIONS SHALL BE PROVIDED BY THE TERMINAL UNIT MANUFACTURER, AS APPROVED BY THE ENGINEER, WITHOUT ADDITIONAL COST. ADJUSTMENTS SHALL BE INDICATED IN THE SUBMITTAL DATA AND FORWARDED TO THE CONTRACTOR FOR COORDINATION WITH

OTHER TRADES.

FPT-3-6 (E)

FPT-3-37 (E)

EQUIPMENT

SET

AIRFLOW

(CFM)

PRIMARY

AIR INLET

SIZE

(IN)

0.40

FAN POWERED TERMINAL UNIT SCHEDULE (SERIES FLOW)

EWT

(°F)

LWT

(°F)

WATER

FLOW

(GPM)

1.4

AIRFLOW

(CFM)

CAPACITY

(BTU/H)

13,900

HEATING COIL

DISCHARGE

STATIC

PRESSURE

(IN WG)

MAX

AIRFLOW

(CFM)

MIN

AIRFLOW

(CFM)

PRIMARY AIR

MAX FAN

AIRFLOW

(CFM)

54321

KEY PLAN

APPROVED BY

CHECKED BY

SHEET NO.

TITLE

DRAWN BY

DATE

PROJECT NO.

SEAL

REVISIONS

8/ 5/

P M

MECHANICAL

THIRD FLOOR

NEW WORK PLAN

JS/MN

08/05/26

50186890

C M

-M C

R M

G R

D F

0- B4

L2 4N

O R

U R

E, V

M-111

0' 8' 16'4'

1 EXISTING THERMOSTAT TO REMAIN.

2 RE-BALANCE EXISTING TERMINAL UNIT AND ASSOCIATED DIFFUSERS

TO THE VALUES INDICATED ON THE DRAWING.

DUCT SIZES INDICATED ARE INSIDE CLEAR DIMENSIONS.

EXISTING SUPPLY AND RETURN DIFFUSERS TO REMAIN IN EXISTING

CEILING. RE-BALANCE SUPPLY AIR DIFFUSERS TO AIRFLOW INDICATED

ON DRAWING.

Scale: 1/8" = 1'-0"1 MECHANICAL THIRD FLOOR NEW WORK PLAN

GENERAL NOTES

KEYNOTES

EDC

COMPUTER CLASS

EXISTING SPRINKLER

HEAD, TYPICAL

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

TENANT FIRE PROTECTION NOTES

VERIFY IN THE FIELD EXACT SIZES AND LOCATIONS OF ALL EXISTING FIRE

PROTECTION SYSTEM PIPING PRIOR TO INSTALLATION OF ANY NEW FIRE

PROTECTION SYSTEM WORK. NEW FIRE PROTECTION SYSTEM WORK

SHALL BE COORDINATED WITH EXISTING CONDITIONS TO ASSURE

PROPER INSTALLATION.

ANY PIPING WHICH MUST REMAIN AS PART OF AN ACTIVE SYSTEM AND IS

IN CONFLICT WITH THE NEW LAYOUT SHALL BE RELOCATED AT NO

ADDITIONAL COST OVER THE CONTRACT AMOUNT.

THE DESIGN AND INSTALLATION OF THE TENANT WET SPRINKLER AND

STANDPIPE SYSTEMS SHALL CONFORM TO THE REQUIREMENTS OF

N.F.P.A. STANDARDS NO. 13 AND 14.

SPRINKLER HEAD LAYOUTS SHALL BE SYMMETRICAL. SPRINKLER HEADS,

VALVES, ALARMS, ETC. SHALL BE MANUFACTURED BY VIKING, GRINNELL,

CENTRAL, STAR OR RELIABLE.

THE CONTRACTOR SHALL PREPARE SPRINKLER SHOP DRAWINGS FOR

SUBMISSION AND APPROVAL BY THE LOCAL CODE AUTHORITY HAVING

JURISDICTION.

THE CONTRACTOR SHALL PROVIDE A HYDRAULICALLY CALCULATED WET

AND/OR DRY SPRINKLER SYSTEM SUFFICIENT TO PROVIDE THE DESIGN

DENSITIES, DEMAND AND HEAD SPACING AS REQUIRED BY N.F.P.A.

STANDARD NO. 13 IN THE TENANT AREAS TO BE MODIFIED. ALL

HYDRAULIC CALCULATIONS AND SPRINKLER SYSTEM DESIGN SHALL BE

BASED ON THE WATER PRESSURE.

THE NEW SPRINKLER AND STANDPIPE SYSTEMS SHALL ACCOUNT FOR

EXPECTED LOSSES OF EXISTING PIPING CONNECTIONS TO THE SYSTEM.

THE AUTOMATIC SUPPLY AND ALL SUPPLY PIPING SHALL BE CAPABLE OF

PROVIDING THE REQUIRED DEMAND IN ACCORDANCE WITH N.F.P.A.

STANDARDS NO. 13 AND 14.

SPRINKLER HEADS SHALL BE QUICK RESPONSE TYPE AND SHALL BE

RATED AND U.L. LISTED FOR THE INTENDED TEMPERATURE

CLASSIFICATION. SPRINKLERS IN AREAS REQUIRING TEMPERATURE

CLASSIFICATIONS OF INTERMEDIATE AND GREATER SHALL REQUIRE THE

USE OF A TEMPERATURE MEASURING DEVICE TO DETERMINE THE

APPROPRIATE TEMPERATURE CLASSIFICATION.

UNLESS OTHERWISE NOTED, ALL NEW SPRINKLER HEADS SHALL BE THE

SAME MANUFACTURER, MODEL, TYPE AND FINISH AS THE EXISTING

SPRINKLER HEADS IN THE AREAS TO BE MODIFIED.

THE CONTRACTOR SHALL REFER TO THE TENANT ARCHITECTURAL

DRAWINGS FOR PROPOSED SPRINKLER HEAD LOCATIONS WHERE

APPLICABLE.

ALL SPRINKLER HEADS MOUNTED IN REMOVABLE ACCESSIBLE CEILINGS

SHALL BE LOCATED AT THE CENTER (+1") OF THE CEILING TILE.

THE CONTRACTOR SHALL REMOVE ALL EXISTING TEMPORARY SPRINKLER

HEADS IN THE AREAS TO BE MODIFIED.

THE EXISTING RUN-OUTS AND DROPS SHALL BE MODIFIED AS REQUIRED

TO CONFORM TO THE FLOOR PLAN SHOWN.

THE CONTRACTOR SHALL BE RESPONSIBLE FOR THE RELOCATION AND

COORDINATION OF THE EXISTING SPRINKLER SYSTEM WITH THE NEW

MEP SYSTEM REQUIREMENTS OF THIS PROJECT.

SUPPORT ALL PIPING FROM EXISTING OR NEW STRUCTURE WITH U.L.

LISTED HANGERS AND SUPPORTS SUITABLE FOR THE INTENDED

INSTALLATION. DESIGN, SELECTION, SPACING AND APPLICATION OF

HANGERS AND SUPPORTS SHALL COMPLY WITH N.F.P.A. STANDARDS,

ANSI B31.1 AND MSS SP-58.

ALL TRAPPED PIPING SHALL BE PROVIDED WITH DRAIN VALVES, NIPPLE

AND CAP.

ALL NEW FIRE PROTECTION PIPING SHALL BE EITHER ASTM-A135,-A795

OR -A53 SCHEDULE 40 BLACK STEEL OR TYPE L HARD DRAWN SEAMLESS

COPPER WATER TUBE. THE USE OF THE COPPER PIPING MATERIALS

SHALL BE LIMITED TO THE SPRINKLER SYSTEM PIPING DOWNSTREAM OF

THE FLOOR CONTROL VALVES.

ALL NEW FIRE PROTECTION PIPING SHALL HAVE THE OPTION TO BE U.L.

LISTED AND FACTORY MUTUAL…

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated Sep 9, 2026.