1305M324Q0421 SOW_Attachment 5 Purge SDS.pdf

Safety Data Sheet Purge

Section 1: Identification

Product Name: Purge Product Code: CHE135 Material Uses: Cleaning Compound Supplier:

ArmorThane USA Inc.

2660 North Eastgate Avenue Springfield, MO, USA 65803 Telephone: 417-831-5090 Fax: 417-831-4397

ArmorThane Coatings Inc.

100, 10803 – 182 Street Edmonton, AB, Canada T5S 1J5 Telephone: 780-444-6200 Fax: 780-444-9405

Emergency Contact: USA – Chemtrec: 800-424-9300 Canada – Canutec: 613-996-6666 Outside USA and Canada – call Chemtrec collect: 703-527-3887

Section 2: Hazards Identification

Classification of the Substance or Mixture: HEALTH, Reproductive Toxicity, 1 B HEALTH, Skin Corrosion/Irritation, 2 HEALTH, Serious Eye Damage/Eye Irritation, 2 A HEALTH, Serious Eye Damage/Eye Irritation, 2 B HEALTH, Specific Target Organ Toxicity – Single Exposure, 3 PHYSICAL, Flammable Liquids, 4

GHS Label Elements:

Hazard Pictograms:

Signal Word: DANGER

Hazard Statements: May damage fertility or the unborn child Causes skin irritation Causes serious eye damage Causes eye irritation May cause drowsiness or dizziness Combustible liquid

Precautionary Statements: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from heat/sparks/open flames/hot surfaces. No smoking. Avoid breathing dust/fumes/gas/mist/vapors/spray. Wash skin thoroughly after handling. Use only outdoors or in a well-ventilated area. Wear protective gloves/protective clothing/eye protection/face protection. IF ON SKIN: Wash with soap and water. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. IF IN EYES:

Rinse continuously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. If exposed or concerned, get medical advice/attention. Take off contaminated clothing and wash before reuse. In case of fire, use dry powder or carbon dioxide for extinction. Store in a well-ventilated place. Keep container tightly closed. Keep cool. Store locked up. Dispose of contents/container to a licensed waste disposal company.

HMIS: Health=2; Fire=3, Physical Hazard: 1, PPE=H – Splash Goggles, Gloves, Apron, Vapor Respirator Insignificant: 0; Slight: 1; Moderate: 2; High: 3; Extreme: 4

See toxicological information (Section 11).

General Information: Read the entire SDS for a more thorough evaluation of the hazards.

Section 3: Composition/Information on Ingredients

Substance/Mixture: Mixture

Ingredient Name CAS Number Percentage n-Methyl-2-pyrrolidone 872-50-4 25-35 Propylene carbonate 108-32-7 20-30 Pentanedioic acid, dimethyl ester 1119-40-0 20-25 Butanedioic acid, dimethyl ester 106-65-0 0-10 Hexanedioic acid, dimethyl ester 627-93-0 0-10 Dipropylene glycol methyl ether 34590-94-8 0-5

Any concentration shown as a range is to protect confidentiality or is due to batch variation.

Section 4: First Aid Measures

Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes, lifting eyelids occasionally to facilitate irrigation. Get immediate medical attention.

Skin Contact: Remove contaminated clothing and shoes immediately. Wash skin with large quantities of soap and water. Wash clothing and shoes before reuse. Seek medical attention if redness, burning, or an itching sensation develops or persists after the area is washed.

Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified personnel. Call a physician or transport to a medical facility immediately.

Ingestion: Seek immediate medical attention. Do NOT induce vomiting unless prompted to do so by a medical professional. This material is an aspiration hazard. Never give anything by mouth to an unconscious person.

Section 5: Firefighting Measures

Flash Point and Method Used: 160oF (71oC), TCC Flammability: OSHA – Flammable Liquid – Class IIIA Firefighting Procedures: Use dry chemical or carbon dioxide. Use cold water spray to cool fire-exposed containers to minimize risk of rupture. A solid stream of water directed into the hot burning liquid could cause frothing. If possible, contain fire run-off water. Positive-pressure self-contained breathing apparatus with full face-piece and full protective clothing should be worn by firefighters. Combustions may produce carbon dioxide, carbon monoxide, nitrogen oxides and other toxic fumes.

NFPA: Health=2; Fire=3; Reactivity=1; Specific Hazard=None Minimal: 0; Slight: 1; Moderate: 2; Serious: 3; Severe: 4

Section 6: Accidental Release Measures

Spill: Isolate and confine spill area. Remove all sources of ignition sources like flames, heating elements, gas engines, etc. Use non-sparking tools. Emergency cleanup personnel should select the specific respirator based on contamination levels found. Use air purifying respirator equipped with full-face organic vapor cartridge if vapors are detected, or are irritating. In areas of high concentrations, fresh air-line respirators or self-contained breathing apparatus and protective clothing should be used. Prevent spreading and contamination of surface waters and drinking supplies. Notify health officials and other appropriate agencies if such contamination should occur.

Cleanup: With adequate ventilation and appropriate protective equipment, cover the area with an inert absorbent material such as clay or vermiculite and transfer to steel waste containers. Ventilate area to remove the remaining vapors.

For major spills in the USA, call Chemtrec at 800-424-9300, and in Canada, call Canutec at 613-996-6666.

Section 7: Handling and Storage

Handling Precautions: Combustible. Avoid contact with eyes, skin, or clothing. Ground containers. Use PPE when transferring material from drums, totes or other containers. If contamination with isocyanates is suspected, do not reseal containers. Do not smoke or use naked lights, open flames, space heaters or other ignition sources near pouring, frothing, or spraying operations. Material can ignite if exposed to open flames.

Storage Requirements: When stored between 60oF and 80oF (15-30oC) in a dry place in sealed containers, the typical shelf life is 6 months or more from the date of manufacture. Consult technical data sheet for shelf life requirements affecting performance quality. Open containers must be handled properly to prevent moisture pickup.

Section 8: Exposure Controls/Personal Protection

Occupational Exposure Limits Exposure Limits

Ingredient WEEL ACGIH OSHA Table Z-1 NIOSH n-Methyl-2-pyrrolidone 10 ppm TWA Dipropylene glycol methyl ether 100 ppm TWA

150 ppm STEL 100 ppm TWA 600 mg/m3 TWA 150 ppm STEL 900 mg/m3 STEL

100 ppm TWA 600 mg/m3 TWA 150 ppm STEL 900 mg/m3 STEL

Propylene carbonate No data available No data available No data available No data available

Pentanedioic acid, dimethyl ester No date available No data available No data available No data available

Butanedioic acid, dimethyl ester No data available No data available No data available No data available

Hexanedioic acid, dimethyl ester No data available No data available No data available No data available

Engineering Controls: General/local ventilation typically control vapor levels adequately. Uses requiring heating or spraying may require more ventilation or PPE. An eyewash station and safety shower or other drenching facilities are recommended in the work area.

Personal Protective Equipment: HMIS PP, H: Splash Goggles, Gloves, Apron, Vapor Respirator Eye/Face Protection: Safety glasses with side-shields conforming to EN166. Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166 (EU).

Skin Protection: Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove’s outer surface) to avoid skin contact with this product Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.

Full Contact: Material: butyl-rubber; Minimum layer thickness: 0.3 mm; Break through time: 480 min; Material tested: Butoject (KCL 897/Aldrich Z677647, Size M) Splash Contact: Material: Nature latex/chloroprene; Minimum layer thickness: 0.6 mm; Break through time: 30 min; Material tested: Lapren (KCL 706/Aldrich ZS677558, Size M); Data source: KCL GmbH, D-36124 Eichenzell; Test method: EN374. If used in solution, or mixed with other substances, and under conditions which differ from EN 374, contact the supplier of the CE approved gloves. This recommendation is advisory only and must be evaluated by an industrial hygienist and safety officer familiar with the specific situation of anticipated use by our customers.

It should not be construed as offering an approval for any specific use scenario.

Body Protection: Impervious clothing. The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace.

Respiratory Protection: Where risk assessment shows air-purifying respirators are appropriate, use a full-face respirator with multi-purpose combination (US) or type ABEK (EN 14387) respirator cartridges as a backup to engineering controls. If the respirator is the sole means of protection, use a full-face supplied air respirator. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or

CEN (EU).

Control of Environmental Exposure: Prevent further leakage or spillage if safe to do so. Do not let product enter drains.

Section 9: Physical and Chemical Properties

Physical State: Liquid Appearance: White liquid Odor: Amine Odor Threshold: No data available pH: No data available Boiling Point: >384oF (196oC) Melting/Freezing Point: No data available Flash Point: 160oF (71oC), TCC Evaporation Rate: <1 Flammability: Combustible Lower and Upper Explosive Limits: No data available Vapor Pressure: No data available Vapor Density: >1 Specific Gravity/Density: 1.092 @ 68oF (20oC) Solubility in Water: Not soluble in water Partition Co-Efficient: No data available Auto-Ignition Temperature: No data available Decomposition Temperature: No data available Viscosity: No data available

Percent Volatile: 22-27% by weight; 35-45% by volume

Section 10: Stability and Reactivity

Chemical Stability: This is a combustible material. Avoid high temperatures, sparks, flames, and extended temperatures over 85oF (25oC).

Conditions to Avoid: High temperatures, oxidizers and open flame.

Hazardous Reactions/Polymerization: Will not occur.

Materials to Avoid: Avoid strong oxidizing materials.

Hazardous Decomposition Products: Carbon monoxide, carbon dioxide and nitrogen oxide vapors from burning.

Section 11: Toxicological Information

Route of Entry: Eyes, ingestion, inhalation, skin Target Organs: Respiratory system, skin, eyes Inhalation: Heating, spraying, foaming or otherwise mechanically dispersing (drumming, venting or pumping) operations of this blend may generate more vapor or aerosol concentrations of its components. High vapor concentrations may cause dizziness, headaches, nausea, loss of balance and coordination, unconsciousness, coma, or respiratory failure. Repeat excessive exposures may cause liver and kidney effects or damage. Reports have associated repeated and prolonged occupational overexposure to solvents with irreversible brain and nervous system damage.

Skin Contact: Prolonged contact may lead to reddening, burning, drying, cracking, skin burns, and may result in absorption of amounts sufficient to cause depression of the central nervous system. Pre-existing skin disorders may be aggravated by exposure to this material. May result in absorption of amounts sufficient to cause depression of the central nervous system.

Eye Contact: Will cause irritation on contact. Symptoms from exposure include stinging, watering, or discomfort of the eyes with redness and swelling.

Acute Toxicity:

n-Methyl-2-pyrrolidone: LD50 Oral – rat – 3914 mg/kg; LD50 Inhalation – rat- 4 h - >5100 ppm; LD50 Dermal – rabbit – 8000 mg/kg Propylene carbonate: LD50 Oral – mouse – 20,700 mg/kg; LC50 Inhalation – rat - >5000 mg/m3; LD50 Dermal – rabbit – 23.8 g/kg Pentanedioic acid, dimethyl ester: No data available Butanedioic acid, dimethyl ester: LD50 Oral – rat – female – 6892 mg/kg; LD50 Inhalation – rat – male and female - >2000 mg/l; LD50 Dermal – rabbit – >5000 mg/kg Hexanedioic acid, dimethyl ester: LD50 Oral – rat – male and female - >5000 mg/kg; LC50 Inhalation – no data available; LD50 Dermal – rabbit - >1000 mg/kg Dipropylene glycol methyl ether: LD50 Oral – rat- 5152 mg/kg; LC50 Inhalation – no data available; LD50 Dermal – no data available Skin Corrosion/Irritation:

n-Methyl-2-pyrrolidone: No data available Propylene carbonate: Skin – rabbit – skin irritation Pentanedioic acid, dimethyl ester: Skin – rabbit – no skin irritation Butanedioic acid, dimethyl ester: Skin – rabbit – no skin irritation (OECD Test Guideline 404) Hexanedioic acid, dimethyl ester: Skin – rabbit – no skin irritation – 48 h Dipropylene glycol methyl ether: serious eye damage/eye irritation

Serious Eye Damage/Eye Irritation:

n-Methyl-2-pyrrolidone: Eyes – rabbit – eye irritation Propylene carbonate: Eyes – rabbit – eye irritation Pentanedioic acid, dimethyl ester: Eyes – rabbit – no eye irritation (OECD Test Guideline 405) Butanedioic acid, dimethyl ester: Eyes – rabbit – mild eye irritation (OECD Test Guideline 405) Hexanedioic acid, dimethyl ester: No data available Dipropylene glycol methyl ether: Eyes – rabbit – mild eye irritation – 24 h Respiratory or Skin Sensitization:

n-Methyl-2-pyrrolidone: No data available Propylene carbonate: No data available Pentanedioic acid, dimethyl ester: No data available Butanedioic acid, dimethyl ester: In vivo assay – mouse – did not cause sensitization on laboratory animals (OECD Test Guideline 429) Hexanedioic acid, dimethyl ester: No data available Dipropylene glycol methyl ether: No data available Germ Cell Mutagenicity:

n-Methyl-2-pyrrolidone: No data available Propylene carbonate: No data available Pentanedioic acid, dimethyl ester: Mammal ovary – negative Butanedioic acid, dimethyl ester: Mouse lymphocyte – negative. In vitro assay S. typhimurium Hexanedioic acid, dimethyl ester: Genotoxicity in vivo – rat – male and female – inhalation – negative Dipropylene glycol methyl ether: No data available Carcinogenicity: No component of this product present at levels greater than or equal to 0.1% as probably, possible or confirmed carcinogen by IARC, ACGIH, NTP, and OSHA.

Reproductive Toxicity:

n-Methyl-2-pyrrolidone: Damage to fetus possible Propylene carbonate: No data available Pentanedioic acid, dimethyl ester: No data available Butanedioic acid, dimethyl ester: No data available Hexanedioic acid, dimethyl ester: Rat – Intraperitoneal: Effects on Fertility: Post-implantation mortality (e.g., dead and/or resorbed implants per total number of implants) Dipropylene glycol methyl ether: No data available Teratogenicity:

n-Methyl-2-pyrrolidone: No data available Propylene carbonate: No data available Pentanedioic acid, dimethyl ester: No data available Butanedioic acid, dimethyl ester: No data available Hexanedioic acid, dimethyl ester: Developmental Toxicity – rat – Intraperitoneal: Specific Developmental Abnormalities: Musculoskeletal system, other developmental abnormalities Dipropylene glycol methyl ether: No data available Mutagenicity:

n-Methyl-2-pyrrolidone: No data available Propylene carbonate: No data available Pentanedioic acid, dimethyl ester: Micronucleus test – rat – male and female Butanedioic acid, dimethyl ester: No data available Hexanedioic acid, dimethyl ester: No data available Dipropylene glycol methyl ether: No data available Specific Target Organ Toxicity – Single Exposure:

n-Methyl-2-pyrrolidone: Inhalation – may cause respiratory irritation Propylene carbonate: No data available

Pentanedioic acid, dimethyl ester: No data available Butanedioic acid, dimethyl ester: No data available Hexanedioic acid, dimethyl ester: No data available Dipropylene glycol methyl ether: No data available Specific Target Organ Toxicity – Repeated Exposure: No data available Aspiration Hazard: No data available Potential Health Effects:

n-Methyl-2-pyrrolidone: No data available Propylene carbonate: Inhalation: May be harmful if inhaled. Causes respiratory tract irritation. Ingestion: May be harmful if swallowed. Skin: May be harmful if absorbed through skin. Causes skin irritation. Eyes: Causes eye irritation.

Pentanedioic acid, dimethyl ester: No data available Butanedioic acid, dimethyl ester: No data available Hexanedioic acid, dimethyl ester: Inhalation: May be harmful if inhaled. May cause respiratory tract irritation.

Ingestion: May be harmful if swallowed. Skin: May be harmful if absorbed through skin. May cause skin irritation.

Eyes: May cause eye irritation.

Dipropylene glycol methyl ether: Inhalation: May be harmful if inhaled. May cause respiratory tract irritation.

Ingestion: May be harmful if swallowed. Skin: May be harmful if absorbed through skin. May cause skin irritation.

Eyes: May cause eye irritation.

Signs and Symptoms of Exposure:

n-Methyl-2-pyrrolidone: Prolonged or repeated exposure can cause vomiting, diarrhea, abdominal pain. Rats exposed to 1-methyl-2-pyrrolidinone at a concentration of 1 mg/L as an aerosol for 10 days showed depletion of hematopoietic cells in the bone marrow and atrophy of the lymphoid tissues of the thymus, spleen and lymph nodes. Bone marrow – irregularities – based on human evidence.

Propylene carbonate: Nausea, headache, vomiting, central nervous system depression. To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated.

Pentanedioic acid, dimethyl ester: To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated.

Butanedioic acid, dimethyl ester: To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated.

Hexanedioic acid, dimethyl ester: To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated.

Dipropylene glycol methyl ether: To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated.

Synergistic Effects: No data available

RTECS:

n-Methyl-2-pyrrolidone: UY5790000 Propylene carbonate: FF9650000 Pentanedioic acid, dimethyl ester: Not available Butanedioic acid, dimethyl ester: WM7675000 Hexanedioic acid, dimethyl ester: AV1645000 Dipropylene glycol methyl ether:JM1575000

Section 12: Ecological Information

Toxicity:

n-Methyl-2-pyrrolidone: Toxicity to fish LC50 – other fish – 4000 mg/l – 96 h; LC50 – Leuciscus idus (Golden orfe) - >500 mg/l – 96 h; Toxicity to daphnia and other aquatic invertebrates EC50 – Daphnia magna (water flea) - > 1000 mg/l – 24 h; Toxicity to bacteria LC50 – bacteria - >9000 mg/l Propylene carbonate: Toxicity to fish LC50 – Leucisus idus melanotus – 5300 mg/l – 96 h; LC 50 – Leuciscus idus (Golden orfe) – 5300 mg/l – 96 h; Toxicity to daphnia and other aquatic invertebrates EC50 – Daphnia magna (water flea) - >500 mg/l – 48 h; Toxicity to algae EC50 – Desmodesmus subspicatus (green algae) - >500 mg/l – 72 h; Toxicity to bacteria LC50 – bacteria - >10,000 mg/l – 72 h Pentanedioic acid, dimethyl ester: Toxicity to fish static test LC50 – Lepomis macrochirus (Bluegill) – 30,838 mg/l – 96 h Butanedioic acid, dimethyl ester: Toxicity to fish semi-static test LC50 – Danio rerio (zebra fish) – 50 – 100 mg/l 0 96 h (OECD Test Guideline 203); Toxicity to daphnia and other aquatic invertebrates static test EC50 – Daphnia magna (water flea) - >100 mg/l – 48 h (OECD Test Guideline 202); Toxicity to algae static test EC50 – Pseudokirchneriella subcapitata - >100 mg/l – 72 h (OECD Test Guideline 201); Toxicity to bacteria growth inhibition EC50 – sludge treatment - >1000 mg/l – 3 h (OECD Test Guideline 209) Hexanedioic acid, dimethyl ester: Toxicity to daphnia and other aquatic invertebrates static test EC50 – Daphnia magna (water flea) – 72 mg/l – 48 h (OECD Test Guideline 202); Toxicity to algae static test – Pseudokirchneriella subcapitata - >100 mg/;l – 72 h (OECD Test Guideline 201) Dipropylene glycol methyl ether: Toxicity to fish LC50 – Pimephales promelas (fathead minnow) - >10,000 mg/l – 96 h; Toxicity to daphnia and other aquatic invertebrates EC50 – Daphnia magna (water flea) – 1919 mg/l – 48 h Persistence and Degradability:

n-Methyl-2-pyrrolidone: Biodegradability Result: 90% readily biodegradable Propylene carbonate: Biodegradability Result: 90% readily biodegradable Pentanedioic acid, dimethyl ester: Biodegradability Result: >=60% readily biodegradable (OECD Test Guideline 301D) Butanedioic acid, dimethyl ester: Biodegradability aerobic – Exposure time 28 d, Result: 74.1% readily biodegradable (OECD Test Guideline 301B) Hexanedioic acid, dimethyl ester: No data available Dipropylene glycol methyl ether: No data available Bioaccumulative Potential: No data available Mobility in Soil: No data available PBT and vPvB Assessment:

n-Methyl-2-pyrrolidone: Results of PBT and vPvB assessment not available as chemical safety assessment not required/not conducted.

Propylene carbonate: No data available Pentanedioic acid, dimethyl ester: Results of PBT and vPvB assessment not available as chemical safety assessment not required/not conducted.

Butanedioic acid, dimethyl ester: Results of PBT and vPvB assessment not available as chemical safety assessment not required/not conducted.

Hexanedioic acid, dimethyl ester: No data available Dipropylene glycol methyl ether: No data available Other Adverse Effects: No data available

Section 13: Disposal Considerations

Waste Disposal: Any disposal practice must be in compliance with all federal, state/provincial and local laws and regulations. Chemical additions, processing or otherwise altering this material may make the waste management information presented in this SDS incomplete, inaccurate or otherwise inappropriate. Waste characterization and disposal compliance are the responsibility solely of the party generating the waste or deciding to discard or dispose of the material. Do not allow material to enter sewers, a body of water, or contact the ground. Refer to RCRA 40 CFR 261, and/or any other appropriate federal, state/provincial, or local requirement for proper classification information.

Disposal should be in accordance with applicable regional, national, and local laws and regulations

Section 14: Transport Information

Proper Shipping Name:

DOT: Flammable Liquid (3) #3, NA1993, Combustible liquid, n.o.s., Combustible liquid, PG III

Section 15: Regulatory Information n-Methyl-2-pyrrolidone (872-50-4): Massachusetts Hazardous Substances List, New Jersey Right-to-Know Hazardous Substances, Pennsylvania Right-to-Know List of Hazardous Substances, SARA 313, TSCA Propylene carbonate (108-32-7): HAP, TSCA Dipropylene glycol methyl ether (34590-94-8): Massachusetts Hazardous Substances List, OSHA Workplace Air Contaminants, Pennsylvania Right-to-Know List of Hazardous Substances, TSCA, Texas Air Contaminants with Health Effects Screening Level

Section 16: Other Information

Preparation Date: October 16, 2017

Disclaimer: The data set forth in this sheet is based on information provided by the suppliers of the raw materials and chemicals used in the manufacture of the aforementioned product. ArmorThane makes no warranty with respect to the accuracy of the information provided by their suppliers, and disclaims all liability of reliance thereof.

ArmorThane USA Inc. and/or ArmorThane Coatings Inc. make no representations or warranties as to the results of the use of the products and assume no obligation in connection therewith. Any written, oral, testing, or technical application advice is to the best of ArmorThane’s knowledge and believed to be correct. It is to be considered only an indication without obligation. Customer is reminded that he must satisfy himself that the product supplied by ArmorThane is suitable for his purpose and conditions of use. Application, uses, and transformation of the products which are beyond our control, are the exclusive responsibility of the customer/applicator. Liability of ArmorThane for all claims, whether arising out of breach of warranty, negligence, strict liability, or otherwise, is limited to the purchase price of the material only.

User’s Responsibility: A bulletin as this cannot be expected to cover all possible individual situations. As the user has the responsibility to provide a safe workplace, all aspects of an individual operation should be examined to determine if, or where, precautions, in addition to those described herein, are required. Any health hazard and safety information herein should be passed on to your customers and employees, as the case may be.

For Your Protection: ArmorThane warrants only that its products meet the specification stated in the sales contract. Typical properties, where stated, are to be considered as representative of current production and should not be treated as specifications. While all the information presented in this document is believed to be reliable and to represent the best available data on these products, no guaranty, warranty, or representation is made, intended, or implied as to the correctness, or sufficiency of any information, or as to the merchantability or suitability or fitness or any chemical compounds or other products for any particular use or purpose, or that any chemical compounds or other compounds or the use thereof are not subject to a claim by a third party for infringement of any patent or other intellectual property right. The user should conduct sufficient investigation to establish the suitability of any product for its intended use. Liability of ArmorThane for all claims, whether arising out of breach of warranty, negligence, strict liability, or otherwise, is limited to the purchase price of the material.

Products may be toxic and require special precautions in handling. For all products listed, the user should obtain detailed information on toxicity, together with proper shipping, handling, and storage procedures, and comply with all applicable safety and environmental standards. Toxicity and risk characteristics of chemical compounds and other products may differ when used with other materials or in a manufacturing or other process. Those risk characteristics should be determined by the user and made known to handlers, processors, and end user.