Corrected_2019_LEI_Unmarked_Vehicle_SUV_spec_sheet_final.docx.pdf

2019 – Southwestern Region Law Enforcement and Investigations Vehicle Standards

Un-Marked LE SUV

The following items will be incorporated into the up-fitting of an un-marked, Law Enforcement patrol vehicle:

Wiring System

Item #1 Patrol Power Modular Universal Power Distribution Center: Provides connectivity an operation to all emergency warning/lighting system, radio communication, and auxiliary electrical components while providing full battery protection. The timer will be set to 1hr. Includes wiring harness.

Item #2 Mobile Radio Wire Harness: Installation of Forest Service LE supplied radio. Radio model will be provided by the FS LEI. In unmarked units, a single Motorola APX mobile radio will be used. These models are both UHF and VHF frequencies and shall be wired to the installer’s proprietary modular wiring harness (“Patrol Power”) assuring proper power delivery to unit and battery protection.

Installation of antenna roof base and wiring to the main unit’s location (typically under rear seat) will be completed. Both UHF and VHF low profile antennas will be installed.

Lighting and Siren Control

Item #3 Hand held siren/light control PA unit: (Government Furnished Equipment (GFE)) A handheld siren with full light controls unit will be installed.

Unit will be capable of operating the siren controls, emergency lights and PA system. The microphone control head and switch will be installed outside of the center console on the driver’s side with the standard metal mic clip or by other means as negotiated with the LEI representative. All other components will be concealed out of sight (typically under rear seat near the radio control unit).

Park Kill feature will be enabled to deactivate the siren when the vehicle is shifted into park. Horn Ring feature will be enabled to change audible siren sound via the horn's ring. PTT push to talk PA system operated by remote handhold siren/light control will be wired for operation through siren speaker when the microphone button is depressed. This will override siren tone. Brake light kill switch to be installed/activated and operated as one of the accessory features on the handheld siren/light control or discretely on the dash accessible by the operator.

The Siren will be programmed to be operated independently of “level” 3 by user. User will be able to activate "Hi-Lo, Wail or Yelp" as needed on the handheld siren control.

NOTE: Lights are to be switched as follows on handheld siren/light control keypad:

Level 1 - rear lights only;

Level 2- front and rear lights without wig wags;

Level 3 - front lights, rear lights, wig wags and siren available if selected by the user.

Item #4 100 Watt Speaker: A 100 watt speaker with bracket included will be mounted underneath the hood in the front portion of the engine compartment out of sight and protected from dirt/mud. FS radio will be wired to allow radio broadcast to be received from speaker at agent's option.

PA system operated by remote handheld siren/light control will be wired for operation through siren speaker.

Communications

Item #5 Wireless Cellular Antenna: Wilson Electronics/ weBoost cellular signal booster, or equivalent. The kit includes amplifier and low profile interior antenna. The amplifier and all wiring shall be concealed. The kit should be powered through the vehicle ignition. Install a universal size phone holder designed for a smart phone – location and style/brand negotiated by LEI or FS representative. A low profile roof antenna will be centered in the roof of the cab and will be a type similar to the AP

Cell/LTE/Wi-Fi by Antenna Plus.

Exterior Lighting

Item #6 Two LED Exterior Lights: Emergency lights installed into the grill - one to be mounted in the front grill of vehicle on driver's side and the other on the passenger side. Lights should be concealed so that they are not visible until activate from inside or outside the vehicle. Light colors will be red on driver’s side and blue on the passenger’s side.

Item #7 WIG-WAG and HIDE-AWAY corner LED lights - Front light assembly: Install two red and two blue LED in each headlight assembly. One red and one blue LED emergency lights mounted in each of the front clear headlight assemblies (one red and one blue of each side of vehicle). Installation of an all-white light bar for scene lighting either discretely into the front grill or to the stock bumper.

Item #8 Rear taillight assembly: Install two white LED lights for tail lights mount one in each of the top red lenses of the assembly on each side of vehicle and two blue LED lights mounted in the white lens backup lights in the rear light assembly on each side of vehicle. All should have variable flash pattern.

Interior Lighting

Item #9 Windshield interior LED light: Government Furnished Equipment (GFE) Install government provided interior lights/light bar.

The lighting will be hardwired and not use 12V plug in connection. The light bar will be Whelen Inner

Edge/ Federal Signal ILS right (passenger) side only or similar.

Item #10 Rear window, interior LED lights: Two emergency red/blue LED lights will be mounted in the upper portion of the rear window spread equally apart. Light colors will be red on driver’s side and blue on the passenger’s side or centered and mounted to rear glass hatch – eg. Lights will not be mounted to interior frame of rear hatch rather they will be mounted to the glass.

Accessories

Item #11 Fire Extinguisher**: 5 pound UL rating 3A40Bc multipurpose dry chemical fire extinguisher. Mounting of fire extinguisher to be negotiated with the LEI representative.

Item #12 Window Tint; all windows will be tinted to FS specifications as made by an LEI or FS representative when vehicles arrive.

Theft Protection

Item #13 Secure-Idle System: Install secure idle switch manufactured by Secure-Idle Inc. or equivalent. The operator should be able to put the vehicle in "Park", push the button on the Secure-Idle

System on the dashboard accessible from the driver's seat (position button on dash board to the left of the steering column), turn the ignition off and remove the key while the vehicle's engine keeps running.

Engine should stop running if someone attempts to drive vehicle without the ignition key. To deactivate, insert the key and turn the ignition to the "on" position. Vehicle components (air conditioning, etc.)

must remain functional while this feature is being used.

Item #14 Patrol Rifle/Shotgun secure storage: Options for securing and storing a patrol rifle and/or a shotgun will be reviewed upon arrival of the vehicle and take into account the specific attributes of the make/model. Any installation will require a locking mechanism and 10 second timer with release button accessible to the driver. Final decision will be made by an FS representative when vehicles arrive.

Optional Equipment:

Item #15 Suspension Leveling spacer kit: Contractor will install aftermarket suspension spacer level kit minimum 2” front and minimum 1.25” rear. Spacers will be made of metal. Kit will be OEM certified. *This option is reserved for SUV’s not received with appropriate clearance for National Forest

System roads.

Item #16 Added power outlets front: A 12-volt DC outlet and USB power outlet combination unit will be installed on the passenger side of the center console as far forward or rearward of the console with the outlets facing upward. Positioning will be approved by LEI or FS representative.

Item #17 Added power outlets rear: One additional unit will be installed in the rear of the vehicle in the cargo compartment in a location accessible to the user.

/s/ James Alford 2/28/2019