1-06.2025.ODOTOhio.01_G50F.pdf

Date: 6/9/2025 Branch: 1400

G50F Basic Unit

ODOT Ohio

1980 West Broad St

Columbus, OH 43223

CRM ID:

1 JDC ID: 06.2025.ODOTOhio.01 G50F

WWW.TEAMJDC.COM

G50F BASIC UNIT

Working Height- 55 feet

Platform Capacity- 600 lbs.

Boom- 3-section channel design

Lift Cylinder- 6" Double Acting

Boom Extension- Hydraulic (No Cables)

Continuous Rotation

Oil Reservoir- Steel, 35 gallon capacity includes Sight and Temperature Gauge. Located On Chassis Frame, Road Side

Subframe-High Strength Full Length

Lower Controls- Electric over Hydraulic on Turret

Front Outriggers- "A" Style Outriggers (14'-6" span)

Secondary Outriggers- "US" Style Outriggers (9'-4" span)

Outrigger Controls- Rear of Bed Each Corner (Hydraulic / Manual)

Cable Carrier- Full Length with Tube for Hoses and Cables. Includes Cover

Platform- Steel, Hydraulic Self Leveling, 40" x 60" Top Mount, 180 degree Rotation

Hydraulic Pump- Fixed Gear

Single Axis, Proportional Upper Controls (Electric over Hydraulic) For Boom Functions and Jib Winch (If applicable)

PTO Hour Meter

Chassis Control- Start/Stop, Throttle and Horn Located at Rear Bumper, Lower Turret Controls and Upper Platform

Emergency Pump- 12-volt with Switch at Lower Turret and Upper Platform

Backup Alarm

LED Lights- Bed marker, Stop / Tail / Turn, and Reverse

Safety Kit- Fire Extinguisher, Safety Triangle Kit, and Two Body Harnesses with Lanyards

Manuals- (1) Operation, Maintenance and Safety, (1) Parts and (2) Electronic copies of each

Maintenance Filters (Additional)- (1) high-pressure and (1) return filter

Base G50F

BED/ BUMPER OPTIONS

18' Steel Bed With LED Lights and Grip Deck Coating

Single Step Rear Bumper - Open Type (Modular)

Tie Down Rails On Both Sides of Bed (Wood/Steel only)

OUTRIGGER OPTIONS

"MH" Out and Down Type Main Outriggers in Lieu of "A" Type

Automatic Rotation Lockout - Prevents Boom from Rotating to Side Where "MH" Outriggers Are Not Fully Extended Horizontally. ("MH" Outriggers Only)

Indicator Light On Dash to Signify Outriggers Not Stowed

Audible Alarm to Signify Outriggers Are Light

LIFTING OPTIONS

5,900 lb. Planetary Winch With Anti-Two-Block Switch, Horn, Two Part Hook, Cable Packer, & 3/8" Cable, Downhaul Ball & Retainer Lug

1,000 lb. Platform Mounted Jib With Hydraulic Winch Mounted in Platform Floor

PLATFORM ACCESSORIES

110 Volt Line to Platform

Hydraulic Accessory Lines to Platform With Flow Control

(2) Sign Forks On Platform

Protective Coating for 40" x 60" Top Mount Platform (Black)

PTO OPTIONS

Hot Shift PTO For Automatic Transmission

TOOL BOX OPTIONS (ALUMINUM)

36" x 24" x 24" Aluminum Underbody Mounted (Treadplate-No paint)

48" x 24" x 24" Aluminum Underbody Mounted (Treadplate-No paint)

Side Reach- 38'-0" (Center of rotation to end of platform)

Front Mount Turret with Boom Stowed Over the Rear of the Chassis

Certified ANSI A92.2 for Vehicle-Mounted Elevating and Rotating Aerial Devices

ADDITIONAL OPTIONS

Hydraulic Accessory Lines at Rear of Bed With Flow Control (6 gpm)

Indicator Light On Dash to Signify Boom Out of Stow

(2) LED Strobe Lights, (1) Mounted on Each Side of Turret Near Top With Switch in Cab

(2) LED Work Lights Mounted on Side of Boom With Switch in Cab.

(2) LED Work Lights Mounted on Front Edge of Operator Platform (Whelen PAR-36 with Switch, PFBS6S)

(2) Whelen TLIA ION T-Series Strobes mounted in front grille, (2) Whelen TLIA ION T-Series Strobes mounted in rear bumper area. Controlled by one switch in the cab.

(2) Rubber Wheel Chocks With Holders. Mounted on Driver's Side Above Rear Axle

Traffic Cone Holder With (3) Orange Traffic Cones

(4) 24" x 24" x 1" Composite Plastic Outrigger Pads With (2) Steel Holders

Canvas Upper Control Box Cover (For standard control box)

Chassis Rating - Sum of Axle Capacities

Additional Printed Copy of Operation, Maintenance & Safety, Parts Manual. Additional Electronic Copy.

Camera- Rear View (Elliott 3021942)

Elliott Factory PDI of Aerial

Operation In-Service Training (8 hrs.)

WELDERS & ACCESSORIES

Welder/Generator Start/Stop Switch in Platform

Welder Leads to Platform - (2) 1 Gauge Cables

Ultimate Power UP12/2500 Watt Power Inverter (Requires Min 24" Tool Box) (For 110V to Platform)

PAINT OPTIONS

HiReach Unit Painted White, Subframe Painted Black, Outriggers Painted Red (STD)

CHASSIS OPTIONS (Select One)

Upfitting Preparation Charge for Customer Supplied Chassis

55' Elliott G50F - Telescoping - Material Handler - NonInsulated

EXCEPTIONS

ALL ELLIOTT PRODUCTS QUOTED DO NOT MEET THE SPECS PROVIDED

HOWEVER THEY ARE POPULAR WITH DOT & TRAFFIC CUSTOMERS SO WE AER PROVIDING AS AN ALTERNATIVE

Proposal Summary

Module, Body, & Install pricing: 256,682.50$

Boom, body, install, delivery to ODOT & training included

Chassis is not included

LeadTime: 180-360 days from receipt of order

Chassis:

Recommended Minimum Chassis Requirements

25,999 GVWR (10,000 lb. FA/19,000 lb. RA)

120" CA

100" AF

900,000 in-lb. RBM frame rails.

Chassis interface to control engine remote start/stop, throttle control, and pto control

(These minimum requirements may change as options are added)

CONSULT JDC TO CONFIRM MINIMUM CHASSIS SPECS

Prices Valid: 30 Days

TECHNICAL SPECIFICATIONS

G50F SIDE VIEW DIAGRAM

G50F

55' / 16,8 m

41' / 12,5 m

600 lbs / 272 kg

40 x 60 in / 102 x 152 cm

Top-Mount

5,900 lbs / 2676 kg

1,000 lbs / 454 kg

11’4” / 3,4 m

11,000 lbs / 4,989 kg

12'6” / 3,8 m

8’ / 2,4 m

10,000 lbs / 4536 kg

19,000 lbs / 8618 kg

Phone: 402-592-4500 Fax: 402-592-4553 Email: sales@elliottequip.com

Maximum Platform Height: 50'

Working Range:

Work Platform: 40”x60" Top-Mount

Platform Leveling System:

Platform Controls:

Lower Controls:

Outrigger Controls:

Outriggers:

Frame:

Turret:

Rotation:

Boom:

Boom Extension:

Lift:

Cylinders:

Hoses:

Oil Tank Capacity:

Hydraulic System:

Pump:

PTO:

Cab Equipment:

Operators Manual & Video: Two

Installation:

Standard Paint:

Bumper:

Weight:

Truck Chassis Required:

Options:

TECHNICAL SPECIFICATIONS

Phone: 402-592-4500 Fax: 402-592-4553 Email: sales@elliottequip.com

Elliott Equipment Company reserves the right to change the speci�cation of any unit at any time without prior notice. This brochure is only a statement of general speci�cations on the date of this publication. For more detailed info on speci�c Elliott trucks go to www.elliottequip.com

TECHNICAL SPECIFICATIONSHIREACH - G50F

Phone: 402-592-4500 Fax: 402-592-4553 Email: sales@elliottequip.com www.elliottequip.com

MAXIMUM LIFTING CAPABILITIES

MATERIAL HANDLING OPERATION

Phone: 402-592-4500 Fax: 402-592-4553 Email: sales@elliottequip.com

Radio Remote Control

Material Handling Jib

Boom-Mounted Winch

Outrigger Pad Holders

Bed Accessories

Platform Accessories

Custom Design Engineering

Line Body

Phone: 402-592-4500 Fax: 402-592-4553 Email: sales@elliottequip.com

CHASSIS DATA

OPTIONS

G50F

Wheelbase (WB) 187” / 475 cm

Cab to Axle (CA) 120” / 305 cm

Cab to End of Frame (EOF) 220” / 559 cm

Frame Section Modulus 7.5 in3 / 120,000 psi / 827,371 kPa

Front Axle Gross Weight Rating 10,000 lb / 4536 kg

Rear Axle Gross Weight Rating 19,000 lb / 8618 kg

Extended Front Frame N/A

Chassis data is minimum general requirements-not for engineering.

Actual dimensions and truck data will depend on truck selection and axle configuration.

1. THE AGREEMENT. Jack Doheny Companies, Inc., (the “Seller”) agrees to sell, transfer and convey its right, title and interest in the new goods, equipment, vehicles and/or other new items (collectively, the “Equipment”) described in Seller’s written Invoice for the Sale of New Equipment (the “Invoice”) to the Buyer subject to the terms and conditions contained herein, which are incorporated into the Invoice, agreed to by the parties hereto, and together consists of the entire agreement between the Seller and Buyer (collectively, the “Agreement”). The Agreement shall be for the benefit of the Seller and Buyer and not for the benefit of any other person or entity. Prior courses of dealing, trade usage and verbal agreements not reduced to a writing signed by the Seller and Buyer, to the extend they differ from, modify, add to or change from the Agreement shall not be binding on the Seller .

2. TERMS OF PAYMENT.

2.1 Payment Date. All payments for the Equipment are due from Buyer on the date of the invoice unless other terms are agreed to in writing between Seller and Buyer. Payment shall be made to Seller at the address specified in the Agreement, without any offset or deduction for any reason.

2.2 Shipping Delays. If any shipment is delayed at the request of Buyer, payment shall become due based on the date Seller is prepared to make shipment, and Seller may invoice Buyer based on such date. All prices for Equipment are F.O.B. Seller's shipping point.

2.3 Delinquent Payments.

2.3.1 Any payment not made by Buyer on or before its due date shall be subject to a late charge on any unpaid balance at a rate of 18% per annum, or the highest interest rate allowed by law, whichever is greater.

2.3.2 If a payment is not made on or before its due date, Buyer agrees that Seller may elect, in addition to any other remedy at law or in equity, to cease performance under the Agreement and any other agreement between Buyer and Seller until such payment is rendered to Seller .

3. DELIVERY. Seller does not guarantee delivery dates.

4. RISK OF LOSS. Buyer assumes all risk of loss of Equipment upon delivery by Seller to carrier if Equipment is shipped. For Equipment that is shipped, Seller agrees to: (a) prepare the Equipment for shipment to Buyer; (b) deliver custody of the Equipment to carrier; (c) make appropriate arrangements for the transportation to carrier; and deliver documents to enable Buyer to obtain possession of the Equipment. Seller shall not be obligated to obtain insurance or to prepay transportation/carrier costs for the Equipment. Buyer agrees to be responsible for and to timely pay all loading, unloading and other charges incidental to transportation of the Equipment. Whether Seller pays transportation charges or not, risk of loss shall pass to Buyer upon delivery of the Equipment to a carrier.

5. INSPECTION OF EQUIPMENT. Buyer has inspected the Equipment and is satisfied with the Equipment’s condition.

6. INDEMNIFICATION. Buyer shall indemnify, hold harmless and release Seller from any and all liabilities, losses, damages, claims, costs and expenses, including attorney fees, arising out of, in whole or in part, from (a) the design, or manufacture of the Equipment; or (b) the use of the Equipment by Buyer and those acting on Buyer’s behalf.

7. MISCELLANEOUS.

7.1 No Assignment. There shall be no assignment of the Agreement by Buyer without the prior written approval of Seller. Any assignment of the Agreement shall not relieve Buyer of its obligations under the Agreement.

7.2 Force Majeure. Neither party will be liable for any delay or failure to perform its obligations hereunder, other than a payment obligation, due to any cause beyond its reasonable control including without limitation, acts of God or of the public enemy, including terrorists, acts of the government in its sovereign capacity, fires, floods, epidemic, strikes, picketing or boycotts, or any other circumstances caused by natural occurrences or third party actions beyond the reasonable control and without the fault or negligence of the party whose performance is affected (“Force Majeure Events”); provided that the affected party provides the other party prompt notice of the applicable circumstance and uses commercially reasonable efforts to re -commence performance as promptly as possible; provided, further, that if the duration of such Force Majeure Event exceeds thirty (30) days, the other party may terminate the Agreement upon delivery of written notice to the affected party.

7.3 Venue. The parties agree that any dispute under the Agreement shall be brought in the applicable state or federal court located in the county in which the

Originating Branch is located and the parties waive any right to a jury trial.

7.4 Construction and Captions. The parties acknowledge that each has reviewed the Agreement and that the normal rules of construction to the effect that any ambiguities are to be resolved against the drafting party shall not be employed in the interpretation of the Agreement or any exhibits or amendments hereto ;

and that section headings appearing in the Agreement are for convenience of reference only and they are not intended, to any extent or for any purpose, to limit or define the text of any section or any subsection hereof. In the event any part of the Agreement is found to be ambiguous, such ambiguity shall not be construed against any party.

7.5 Entire Agreement. The Agreement constitutes the sole and entire agreement between the parties and supersedes all prior and contemporaneous statements , promises, understandings or agreements, whether written or oral.

7.6 Amendments. The Agreement may be amended, modified or altered at any time upon the approval of the Seller and Buyer; however, any such amendment must be in writing and signed by the Seller and Buyer in order for such amendment to be of any force and effect .

7.7 Partial Invalidity. In the event that any provision of the Agreement is declared by any court of competent jurisdiction or any administrative judge to be void or otherwise invalid, all of the other terms, conditions and provisions of the Agreement shall remain in full force and effect to the same extent as if that part declared void or invalid had never been incorporated in the Agreement and in such form, the remainder of the Agreement shall continue to be binding upon the parties.

7.8 Counterparts. The Agreement and any amendment thereto may be signed and executed in one or more counterparts, each of which shall be deemed an original and all of which together shall constitute one Agreement. Delivery of an executed counterpart of a signature page of the Agreement by facsimile or email shall be effective as delivery of an originally executed counterpart of the Agreement .

7.9 Authority. Each person(s) executing the Agreement as an agent or in a representative capacity warrants that he or she is duly authorized to do so .

NO WARRANTY. SELLER MAKES NO WARRANTIES OR REPRESENTATIONS EXPRESS OR IMPLIED BY OPERATION OF LAW OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MARKETABILITY OR FITNESS FOR PARTICULAR PURPOSE, ALL OF WHICH

ARE SPECIFICALLY HEREBY DISCLAIMED. To the extent allowed by law and those agreements, Seller transfers and assigns to Buyer the Equipment manufacturer’s warranties, if any such warranty is provided by the Equipment manufacturer. In no event shall Seller be liable to Buyer for any incidental , consequential, special, exemplary, and/or punitive damages, including without limitations, loss of revenue or profit.

SALE OF NEW EQUIPMENT

TERMS AND CONDITIONS

702-665-5397 info@dohenycompany.com dohenycompany.com

Customer:

By:

Date:

Email:

Terms and Conditions

***Surcharges or rate increases issued by manufacturer that affect this quote following quote acceptance, but prior to order delivery, will be the responsibility of Buyer. Any surcharge or increase that is applied to this purchase will be applied at same cost as issued by manufacturer.***

• Acceptance of this Proposal is subject to availability of the Equipment listed above.

• Sales Price does not include any applicable sales taxes. Buyer is responsible for and agrees to pay all applicable sales tax.

• The Sale of New Equipment Terms and Conditions are incorporated into and made a part of this Proposal upon acceptance and execution of this Proposal by both parties.

• Execution of this Proposal by Seller and Buyer constitutes a binding agreement between the parties.

• If this Proposal is not executed by both parties within thirty (30) calendar days from the

Proposal Date, this Proposal shall become null and void, unless subsequently executed by both Buyer and Seller.

Thank you for your consideration of this proposal.

This proposal becomes a contract for delivery and payment of the merchandise listed above only when signed by the customer or one of its officers.

Sincerely yours, Mick Gerber Mick Gerber Vice President - Electric Utility Products Group 317/617-1404 MickGerber@TeamJDC.com

Purchase Order#: