W911SD-24-Q-0001 SPEC PACKAGE BUTTONS for Full Dress Hat.pdf
PDF 759 KB Posted
- Solicitation number
- W911SD-24-Q-0001
About this file
This document contains two military specification sheets and a sources sought notice for a federal contract opportunity. The specification sheets provide requirements for United States Military Academy dress hat buttons, including dimensions, materials, finishes, markings, packaging, and inspection criteria. The 25 ligne ball button with tube screw must be made of 85/15 red brass, gold plated with a minimum of 1 grain of gold. The 43 ligne button with tube screw and hook must be made of the same material, plated with a minimum of 2 grains of gold. The sources sought notice is for these U.S. Army West Point buttons for full dress hats under solicitation W911SD-24-Q-0001, issued by the Department of the Army Materiel Command Mission and Installation Contracting Command at Fort Eustis.
View the file
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
AMSC N/A Page 1 of 2 FSC 8455
INCH-POUND
MIL-DTL-1563/9B
6 January 2014
SUPERSEDING
MIL-DTL-1563/9A
18 April 1997
DETAIL SPECIFICATION SHEET
INSIGNIA, U.S.M.A., BUTTON, BALL, 25 LIGNE WITH TUBE SCREW
This specification is approved for use by all Departments and Agencies of the Department of Defense
The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-B-1563.
MATERIAL: Red Brass 85/15 (UNS Alloy No. C-230)
FINISH: Gold Plated, Matte Finish, Rims Lathe, Beveled and Burnished, Polished Highlights.
TEST FOR GOLD PLATING: Quantitative (Average Grains of gold per dozen button) – Minimum 1 Grain.
DIMENSIONS: 25 Ligne + 1 Ligne. (REF)
MARKING FOR IDENTIFICATION: Back Shell
SUGGESTED PACKIGING: Standard Commercial UNIT PACKAGING: 24 buttons shall be mounted on a 3 X 4 inch card and wrapped.
INTERMEDIATE PACKAGING: 144 per box.
Source: https://assist.dla.mil -- Downloaded: 2016-12-15T20:37Z Check the source to verify that this is the current version before use.
MIL-DTL-1563/9B
ATTACHING DEVICE:
1. The attaching device shall be screw post with tube screw type. The screw post and tube screw shall conform to the dimensions shown above.
2. The screw post shall be hard soldered or electronically fused to the back of the button in the location shown.
NOTE:
The term (REF) refers to the measurements taken from the Government furnished hub or die.
CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes.
Custodian: Preparing activity:
Army - IH Army - IH
Review activity: (Project No. 8455-2014-011)
DLA - CT
NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https://assist.dla.mil.
Source: https://assist.dla.mil -- Downloaded: 2016-12-15T20:37Z https://assist.dla.mil/
AMSC N/A Page 1 of 2 FSC 8455
INCH-POUND
MIL-DTL-1563/8C
6 January 2014
SUPERSEDING
MIL-DTL-1563/8B
30 April 1997
DETAIL SPECIFICATION SHEET
INSIGNIA, U.S.M.A., BUTTON, 43 LIGNE WITH TUBE SCREW AND HOOK
This specification is approved for use by all Departments and Agencies of the Department of Defense
The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-B-1563.
MATERIAL: Red Brass 85/15 (UNS Alloy No. C-230)
FINISH: Gold Plated, Matte Finish, Rims Lathe, Beveled and Burnished, Polished Highlights.
TEST FOR GOLD PLATING: Quantitative (Average Grains of gold per dozen button) – Minimum 2 grains.
DIMENSIONS: 43 Ligne + 1 Ligne (REF)
MARKING FOR IDENTIFICATION: Back
SUGGESTED PACKIGING: Standard Commercial UNIT PACKAGING: Individual wrapped.
INTERMEDIATE PACKAGING: 100 per box.
Source: https://assist.dla.mil -- Downloaded: 2015-12-30T19:37Z
MIL-DTL-1563/8B
ATTACHING DEVICE AND SCREW POST:
1. The attaching device shall be screw post with tube screw and hook type.
2. The post, tube screw and hook shall conform to the dimensions shown.
3. The screw post shall be hard soldered or electronically fused to the back of the button in the location shown.
NOTES:
The term (REF) refers to the measurements taken from the Government furnished hub or die.
CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes.
Custodian: Preparing activity:
Army - IH Army - IH
Review activity: (Project No. 8455-2014-010)
DLA - CT
NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https://assist.dla.mil.
Source: https://assist.dla.mil -- Downloaded: 2015-12-30T19:37Z https://assist.dla.mil/
11/20/2018 Insignia U.S. Brass Evaluation. The Government reserves the right to perform inspections when deemed necessary to assure supplies and services conform to prescribed requirements.
NOTE: One (1) Major constitutes a failure, and two (2) minor defects equals one (1) Major which constitutes a failure.
Defects Classification
Major Minor
Materials:
a. Materials not Red Brass 85/15 (UNS Alloy No. C-230) or Zinc
Aluminum
b. Finish is not 24K Gold Plated, Mirror-like Polished and shall match The Institute of Heraldry (TIOH) Metal Finish Chip
Number6
X
Dimensions:
a. Height (Overall) not 7/16 in.
b. Width (Overall) not 27/32 in.
c. Thickness (At thickest point) not .060 +/- .010 in.
Attaching Device:
a. Attaching device is not prong and wing type clutch
b. Prongs are not located on the vertical center line, equidistant from each end and 5/8 in. +/- 1/64 in. apart
| Dress Cap Button with Screw Tube Spec |
| FD Hat Insignia-screwpost spec drawing- BLUE PRINTS |
| MIL-DTL-1563-8C FD Hat Button Shako Hook and Screw |
| W911SD-24-Q-0001 SPEC PASS FAIL BUTTONS for Full Dress Hat |
File details come from the government source that posted it. Updated .