Technical_Specifications.pdf

Technical Specifications

A. CAD /CAM Acquisition unit

1. Omnicam White LED Continuous streaming

2. Color Display facilitates between tooth and gingiva

3. Capability to imitate enamel shades

4. Must be FDA approved

5. Implant treatment possible using intraoral scan body

6. Chairside Implant treatment capability

7. Interfaces: Open Inlab/Open Model/Open Galileos/Open 3Shape

8. Imaging Technique: Filming

9. Distance above the tooth scanning: No more than 15mm.

10. Comes with acquisition unit and 64 bit Windows Computer

11. Software:

i. Acquisition Preparation

ii. Antagonist and bite situation

iii. Computation of the 3D Model

iv. Insertion of the preparation margin

12. Definitive acquisition unit specifications that must be met:

Configuration Cart-mounted all-in-one intraoral scanning system Monitor 19” 1280 x 1024 Resolution Network Connection LAN Camera Weight No more than 313 Grams (.69 LBS) Camera Dimensions Camera Length

Overall Length no larger then: 228 MM Length of Camera Sleeve no larger then: 108 MM Height and Width of Tip no larger then: 16X16

Powder Free Operation must be powder free Supply Voltage Standard Mains Power Supply (100–230 V, 50/60 Hz)

Optional Uninterruptable Power supply (Short Term Battery) Capture Time Single Tooth: 2 Seconds

Quadrant: 20 Seconds Full Arch: 60 Seconds Articulated Upper and Lower: 2 Minutes

Capture Method Color Coded triangulation Focal Depth No more than 15mm.

Warranty 1 Years Parts / 1 Years Labor

3 Years optional

B. Wet/Dry 5-Axis Milling and Grinding Unit

1. Material Compatibility:

i. Zirconia

ii. Polymer

iii. Wax

iv. Composites

v. Glass Ceramics

vi. Hybrid Ceramics

vii. Metals

2. Material Size: Blocks in sizes I8 to B40L with specialized block holder capable of holding 6 blocks size I14/C14; Discs 98 mm diameter x up to 30 mm height.

3. Open Architecture

4. Wet Grinding capable

5. Number of Axes: 5

Configuration Intended for use in dental laboratories Supply Voltage 100V-230V Mains Frequency 50/60 Hz Nominal Power 200 VA Nominal Power output 2.0A Permissible line voltage fluctuations ±10% of nominal voltage Compressed Air Connection Min. 7.0 bar/102psi Compressed Air Consumption Min. 50 l/min

Short-term up to 100 l/min Air Pressure (within the following range) 700 hPa – 1060 hPa Temperature Range (within the following range) +5 ℃ - +40 ℃ Humidity range (within the following range)

80% rel. up to 31 °C decreasing to 50% rel. up to 40 °C

Operating mode Continuous operation Degree of protection against ingress of water

Usual device (without protection against ingress of water), IP 20

Shock stress 1J (IK06) on door glass, 5J (IK08) on remaining device

Connections

Network: RJ45/LAN

USB 2.0/3.0

USB 5V OUT

Communications interface for suction Compressed air quick-connect coupling Service interface Mains connection

AC 100V ... 240V

Weight (Not to exceed) 192 lbs.

Dimensions (WxHxD) in mm (Not to exceed) 629 x 795 x 575 Warranty 3 year warranty

C. Air Compressor

1. Ultra dry, clean dental compressed air

2. Virtually Maintenance free

3. New Membrane Dryer system produces driest possible compressed air while maximizing performance

4. Improved intake filters, new purge muffler design, shock mounts and flat frame reduce vibration and noise

5. Compact shape for space saving installation

Max Number of Simultaneous users 3 Number of heads 1 Voltage (Min/Max) 200/250 Full load amps 8.0 Dimensions (Not to exceed) 30.5” x 29” x 20” Dimensions with sound reducing cover (Not to exceed) 32” x 31” x 22.25” Weight (not to exceed) 200 lbs

D. Milling Unit.

1. Utilize two or Four Bur Motors plus one x Block shaft motor

2. Touch display screen

3. Barcode reader

4. External Tank

5. Filter unit for standard water tank

6. Filter set for external water tank

7. Broken bur detection

8. Automatic worn bur compensation

9. Resumption of interrupted milling

10. High Milling speed – Must be able to mill a crown in 15 minutes

11. Large Milling Volume – Maximum Material block size 85 x40 x 22mm

12. Must be able to Mill and/or Grind

i. Inlays

ii. Onlays

iii. Veneers

iv. Crowns

v. Single unit Copings

vi. Bridge frameworks

vii. Abutments

viii. Models

ix. Telescopes

x. Bars

xi. Attachments

xii. Surgical Guides

13. Material:

i. Feldspar/Glass Ceramic

ii. Lithium disilicate

iii. Zirconia

iv. Alumina

v. Spinell

vi. Lucite

vii. Infiltration Ceramic

viii. Polymers

ix. Lithium disilicate

x. Translucent Zirconia

xi. Yytrium Zirconia

xii. PMMA

xiii. Chrome Cobalt

xiv. Resin nano ceramic

Definitive Milling Unit specifications that must be met:

Supply Voltage 100V-230V Mains Frequency 50/60 Hz Nominal Power 320 VA Network Connection LAN

Milling time

Inlay 3-5 mins (Feldspar/Lucite) Crown 8-10 mins (Feldspar) Crown 10-12 mins (Lithium Disilicate) Bridge 15-18 mins (PMMA)

Warranty 1 Years Parts / 1 Years Labor 3 Years optional

E. Model Scanner:

1. Fully Automated with Manual scan capability

2. Must include a 64 bit Windows Computer

3. 5 – Axis Scanning technology

4. Lab Software

i. Features:

1. Design of restorations

2. Export of scan via open STL

3. Vertical Articulator

4. Ability to create surgical guides

5. Biogenetic tooth design

F. High Temperature Oven.

1. High-temperature sintering furnace iHTC Speed

2. Overnight Sintering

3. Pre drying and Speed Sintering in a single process

4. Speed sintering tray, crucible rack, crucible fork

5. Sintering beads

6. Connecting cable

7. Super speed crucible, crucible fork, crucible rack

Definitive High temperature oven specifications that must be met:

Supply Voltage 200V – 240V Mains Frequency 50/60 Hz Nominal Power 2500 W Maximum Sintering temperature 1650

G. Sustainment

1. Software Updates

2. Software Upgrades

3. Sirona Connect Support

4. Technical Phone Support