21Q0054 Amendment 3.pdf

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print)

30-105-04EXCEPTION TO SF 30

APPROVED BY OIRM 11-84

STANDARD FORM 30 (Rev. 10-83) Prescribed by GSA

FAR (48 CFR) 53.243

See Page 2

1. CONTRACT ID CODE PAGE OF PAGES

1 3

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

16C. DATE SIGNED

BY 11-Aug-2021

16B. UNITED STATES OF AMERICA15C. DATE SIGNED15B. CONTRACTOR/OFFEROR

(Signature of Contracting Officer)(Signature of person authorized to sign)

8. NAME AND ADDRESS OF CONTRACTOR (No., Street , County, State and Zip Code) X W911KF21Q0054

X 9B. DATED (SEE ITEM 11)

15-Jul-2021

10B. DATED (SEE ITEM 13)

9A. AMENDMENT OF SOLICITATION NO.

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

X The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offer X is extended, is not extended.

Offer must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended by one of the following methods:

(a) By completing Items 8 and 15, and returning 1 copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted;

or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN

REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. ACCOUNTING AND APPROPRIATION DATA (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS.

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE

CONTRACT ORDER NO. IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation date, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(B).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority)

E. IMPORTANT: Contractor is not, is required to sign this document and return copies to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

10A. MOD. OF CONTRACT/ORDER NO.

2. AMENDMENT/MODIFICATION NO. 5. PROJECT NO.(If applicable)

6. ISSUED BY

3. EFFECTIVE DATE

11-Aug-2021

CODE

ACC-ANAD

KISHAWN BANKS

7 FRANKFORD AVE

ANNISTON AL 32601-4199

W911KF 7. ADMINISTERED BY (If other than item 6)

4. REQUISITION/PURCHASE REQ. NO.

CODE

See Item 6

FACILITY CODECODE

EMAIL:TEL:

W911KF21Q0054

SECTION SF 30 BLOCK 14 CONTINUATION PAGE

The following items are applicable to this modification:

AMENDMENT NOTES

1. The purpose of the amendment is to add a revised Statement of Work and extend the offer due date.

2. Revised Statement of work addresses an error in Paragragh 3.1.3 and 3.1.4. The revised SOW is attached as SOW Large Cylindrical OD Grinder – Revised as of 8-11- 21.

Paragraph 3.1.3 change

FROM

The minimum swing over the table shall be 16.50 inches with a maximum grinding diameter of up to 21.5 inches.

TO

The minimum swing over the table shall be 16.50 inches with a maximum grinding diameter of up to 15.75 inches.

Paragrah 3.1.4 change

FROM

Wheel-head (X-axis) shall be set to an angle of 90 degrees in reference to the Z-axis. Spindle motor shall be a minimum of 28 Horsepower (HP). Wheel spindle shall be supplied with force fed lubrication with pressure check. Wheel size shall be (ODxWxID) approximately 29” x 5.12” x 12.0” and a maximum peripheral speed of approximately 6500 sfpm. Max wheel width for standard wheel flange shall be 5.12”. Mounted to the wheel-head should be a Z-axis part feature locator.

TO

Wheel-head (X-axis) shall be set to an angle of 90 degrees in reference to the Z-axis. Spindle motor shall be a minimum of 28 HP. Wheel spindle shall be supplied with force fed lubrication with pressure check. Grinding Wheel size shall be (OD x ID x W) 30” x 12.0” x 3.0” and a maximum peripheral speed of approximately 6500sfpm. Max wheel width for standard wheel flange shall be 6.0”. Mounted to the wheel-head should be a Z-axis part feature locator.

3. The offer due date has been extended FROM 16 August 2021 TO 24 August 2021.

4. All other Terms and Conditions remain unchanged.

SUMMARY OF CHANGES

SECTION SF 1449 - CONTINUATION SHEET

SOLICITATION/CONTRACT FORM

The required response date/time has changed from 16-Aug-2021 11:00 AM to 24-Aug-2000 11:00 AM.

(End of Summary of Changes)

W911KF21Q0054