Attachment_0002_-_BEB043_Deprocessing_checklist.xls

XLS spreadsheet 230 KB Posted Jun 26, 2019

Attached to: BEB043 Fire Repair Services
Solicitation number: W56HZV19R0155
Issued by: Department of the Army Materiel Command Contracting Command Detroit Arsenal

About this file

From the source

Deprocessing Checklist

View the file

Other files

File	Type	Posted
W56HZV-19-R-0155.pdf	PDF	Jun 26, 2019
Attachment_0003_-_BEB043_GFP.pdf	PDF	Jun 26, 2019

On GovTribe

Work with this file

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

Title Page

UNCLASSIFIED
Attachment 0002 - BEB043 Deprocessing Checklist
W56HZV-19-R-0155
	20 May 2019
Distribution Statement A: This is approved for public release: distribution is unlimited.
UNCLASSIFIED

Cover Sheet Page 1

M30 BEB DEPROCESSING CHECKLIST		Page 1 of 4
NOUN/MODEL: Bridge Erection Boat		Start Time:
NSN: 1940-01-615-8699	Ambient Conditions:	End Time:
BEB SERIAL No:
GAINING UNIT:
TECHNICAL REFERENCES: 5-1940-324-10
SPECIAL INSTRUCTIONS:
1. This checksheet shall be used to verify that all tasks have been completed. As each task is verified, the inspector will confirm the step is complete by initialing in the appropriate space. After completion, sign and date this coversheet.
2. Attach a completed DA 2404 to each deprocessing checklist.
3. Inspect the BEB for signs of any damage during transportation.
4. Do not launch the BEB with the engines running.
5. Do not engage the transmissions with the BEB out of the water.
6. Ensure the engine temperature does not exceed 200 degrees while running out of the water.
NOTE
Any questions or suggested changes regarding the contents of this checklist should be addressed to PdM Bridging.
Deprocessing Performed by:		DATE:
PM Representative Signature:		DATE:

Page 2 PMCS and Swimtest

M30 BEB DEPROCESSING CHECKLIST	Page 2 of 4
SERIAL NO:
Action:	Initials
PMCS AND SWIMTEST
1. Connect battey cables on both battery banks and perform before operation PMCS IAW TM 5-1940-324-10 WP 0104 a). Connect inpection light and search light and check operation
2. Move to launch site and perform pre-start checks.
3. Launch BEB. Start and record beginning engine hours: Port Engine__________ Starboard Engine____________
4. Prior to disconnecting the winch hook and getting under way, open all hatches and ensure there is no water ingress or fuel leaks.
5. Manuever BEB to open water: a). Ensure there is raw water discharge from both port and starboard. b). Perform 360 degree turns in both directions. Inspect for binding in steering
6. Center the helm and operate the BEB ahead in a straight direction using the throttle control assembly only. Ensure the BEB travels in a straight line.
7. Center the helm and operate the BEB astern in a straight direction using the throttle control assembly only. Ensure the BEB travels in a straight line
8. Perform power port and starboard turns at 1500-1800 RPMs. Ensure the steering doesn’t bind
9. Perform waterjet flushing. Ensure flushing operates.
10. In calm water, perform an emergency stop by rapidly moving from forward to reverse thurst. Caution should be taken when performing this manuever.
11. Shut down port and starboard engines and open all hatches to inspect for leaks
12. Close all hatches and restart both port and starboard engines

Page 3 swimtest cont.

M30 BEB Deprocessing Checklist	Page 3 of 4
SERIAL NO:
Swimtest continued	INITIALS
14. Place the backup control panel in backup and manuever the BEB ahead, astern, port and starboad. Ensure the backup control panel functions properly.
15. Ensure the GPS depth sounder performs correctly. Measure water depth in two different locations. Depth one:_________ Depth two:_______
16. Operate the BEB for 10 minutes at a maximum of 1170 RPM. Upon completion annotate the following: a). Speed_____________ b). Gear oil pressure: Port___________ Starboard__________ c). Gear oil temperature: Port_________ Starboard________ d). Coolant temperature: Port____________ Starboard________ e). Engine oil pressure: Port________ Starboard__________ f). Hydraulic temperature_______
17. Operate the BEB for 10 minutes at a maximum of 1560 RPM. Upon completion annotate the following: a). Speed_____________ b). Gear oil pressure: Port___________ Starboard__________ c). Gear oil temperature: Port_________ Starboard________ d). Coolant temperature: Port____________ Starboard________ e). Engine oil pressure: Port________ Starboard__________ f). Hydraulic temperature_______
18. Operate the BEB for 10 minutes at a maximum of 2080 RPM. Upon completion annotate the following: a). Speed_____________ b). Gear oil pressure: Port___________ Starboard__________ c). Gear oil temperature: Port_________ Starboard________ d). Coolant temperature: Port____________ Starboard________ e). Engine oil pressure: Port________ Starboard__________ f). Hydraulic temperature_______

Page 4 swimtest cont.

M30 BEB Deprocessing Checklist	Page 4 of 4
SERIAL NO:
Swimtest continued	INITIALS
19. Operate the BEB for 10 minutes at a maximum of 2340 RPM. Upon completion annotate the following: a). Speed_____________ b). Gear oil pressure: Port___________ Starboard__________ c). Gear oil temperature: Port_________ Starboard________ d). Coolant temperature: Port____________ Starboard________ e). Engine oil pressure: Port________ Starboard__________ f). Hydraulic temperature_______
20. Operate the BEB for 10 minutes at maximum RPM. Upon completion annotate the following: a). Speed_____________ b). Gear oil pressure: Port___________ Starboard__________ c). Gear oil temperature: Port_________ Starboard________ d). Coolant temperature: Port____________ Starboard________ e). Engine oil pressure: Port________ Starboard__________ f). Hydraulic temperature_______
21. Exercise throttles (minumum) 10 times from full to idle positions. Check for proper operation, performance/fuel knocks.
22. Shut down both engines and conduct the following: a). open hatches b). check for leaks c). Engine oil level d). Transmission oil level e). Hydraulic fluid level
23. Retrieve BEB and conduct the following: a). Remove bilge plug b). Inspect keel cooler for damage c). Inspect waterjet intake for damage d). Inspect bottom of hull for damage
24. Perform retest if needed and record all deficiencies on DA form 2404
25. PASS: ______ FAIL: ______ Final hour meter readings: Port: ________ Starboard: _______
REMARKS:

File details come from the government source that posted it.