PWS_NG-0023-16-2.pdf

PERFORMANCE WORK STATEMENT

FOR REPAIR AND CALIBRATION OF

ROHDE & SCHWARZ EMI TEST RECEIVER

USATA-NG-0023-16

1.0 GENERAL. The U.S. Army Test, Measurement and Diagnostic Equipment Activity (USATA) has a requirement to acquire commercial factory repair and calibration of a Rohde & Schwarz Model ESIB40 EMI Test Receiver, Serial Number 100008, manufactured by Rohde & Schwarz USA, Inc. The Model Model ESIB40 EMI Test Receiver is managed by the U.S. Army TMDE Support Center at Redstone Arsenal, Alabama and shall be shipped to the contractor's facility for repair.

2.0 GOVERNMENT TASKS.

2.1 The government shall be responsible for shipment of the unit from USAT A facilities to the Contractor's facility at government expense. The unit shall be shipped to the Contractor's facility not later than 48 hours (excluding weekends and holidays) after receipt of notice of contract award.

2.2 The U.S. Army TMDE Activity, Redstone Arsenal, AL (Acceptance DODAAC: W80RA6) shall be responsible for receiving, inspection and acceptance in DFAS Wide Area Workflow

(WAWF).

3.0 CONTRACTOR TASKS.

3.1 The Rohde & Schwarz Model ESIB40 EMI Test Receiver, Serial Number 100008, requires factory repair, per RMA 309045401 dated 3 December 2015. Based on preliminary evaluation, the unit requires replacement of the Step Attenuator and full calibration, with certificate, to ISO 17025 standards.

3.2 The Contractor shall furnish all labor, material and equipment required to provide diagnosis, repair and calibration of the items in accordance with the manufacturer's specifications.

3.3 The Contractor shall not provide repair or other services outside the scope of this contract without authorization from the government Contracting Officer. It is the government Contracting Officer only that possesses the authority to make changes in the scope and price of this contract. In the event that the equipment requires repair in excess of this contract, the contractor shall contact the issuing government contract representative identified in Block 7 of the contract.

4.0 DEFINITIONS ..

Accredited Calibration. When an item requires calibration, the contractor shall calibrate the item in accordance with or compliant to ISO/IEC 17025. At a minimum, a calibration report with the following will be included: as found data, as left data, calibration standards used, and the measurement uncertainty.

5.0 PLACE OF PERFORMANCE. Performance shall take place at the Contractor's facilities.

Attachment 01

USATA-NG-0023-16

6.0 PERIOD OF PERFORMANCE. In accordance with Section B of the contract.

7.0 GOVERNMENT-FURNISHED EQUIPMENT. None.

8.0 QUALITY REQUIREMENTS. Not Applicable.

9.0 CONTRACTOR MANPOWER REPORTING REQUIREMENT - SERVICE CONTRACTS.

9.1 Dep~rtment of the Army requires reporting of all contractor labor hours associated with services! to include calibration and repair1 provided to United States Army organizations;

therefore I

9.2 The contractor shall report ALL contractor labor hours (including subcontractor labor hours) required for performance of services provided under this contractor for the U.S. Army TMDE Activity via secure data collection site. The contractor is required to completely fill in all required data fields using the following web address: http://www.ecmra.mill and then click on "Department of the Army CMRA" or the icon of the DOD organization that is receiving or benefiting from the contracted services.

9.3 Reporting inputs will be for the labor executed during the period of performance during each Government fiscal year {FY) 1 which runs October 1 through September 30. While inputs may be reported any time during the FY, all data shall be reported no later than October 31 of each calendar year, beginning with 2014. Contractors may direct questions to the help desk by clicking on 11Send an email" which is located under the Help Resources ribbon on the right side of the login page of the applicable Service/Component's CMR website.

2 Attachment 01