Tech Data Section C-D PGC 00333 Aug 2022.docx

SECTION C- DESCRIPTION/SPECIFICATION

PGC00333 Coveralls, Utility, Type I, Class 1, Shade Blue 3329 (PGC00333)

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RD002, COVERED DEFENSE INFORMATION APPLIES

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS)

RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER)

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

RQ018: CONTRACTOR RETENTION OF SUPPLY CHAIN TRACEABILITY DOCUMENTATION (AUG 2016) This item requires supply chain traceability documentation in accordance with DLA Directive (DLAD) Procurement Notes #C03 Contractor Retention of Supply Chain Traceability Documentation (AUG 2016)#. The full text of C03 can be found in the DLAD Procurement Notes on the Web at: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx.

(End of TQ Requirement)

IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION, PACKAGING, PACKING AND MARKING.

COVERALLS SHALL BE MADE IN ACCORDANCE WITH NCTRF-CID-55095, DATED JANUARY 31, 2017.

PATTERN DATE: 22 February 2017

STANDARD SAMPLE OF CLOTH, TWILL, POLYESTER AND

COTTON, BLUE SHADE 3329, - PIECE NO. 18320

Standard sample for button Navy shade Dark Blue 501 is available for shade only.

Additional Information for NCTRF-CID-55095:

Page 1, paragraph 2.2 At end of page insert: "DISTRIBUTION STATEMENT A: Approved for public release."

Page 2, paragraph 3.1, line 15 delete and substitute: "The coveralls shall have a hanger loop with a 2-inch (± 1/2) free opening positioned inside the back neck"

Page 2, paragraph 3.1.1.1, line 1 Delete "Front patch pockets" and substitute "Breast patch pockets".

Line 4 Delete "They" and substitute "The".

Page 3, paragraph 3.1.5, After line 3 add:

"a. Undersleeve opening construction: Turn raw edge of underply extension up over itself, 1/2 inch from edge of sleeve tapering to 1/4 inch at top of sleeve opening. Fold over body of material and stitch 1/16 inch from folded edge. Seam type EFb-1, stitch type 301.

b. Top sleeve opening construction: Turn raw edge of top ply facing under 1/2 (+1/16) inch. Fold back under body of material and stitch 1/16 inch from folded edge continuing across width of facing. Facing shall finish 1/2 (+1/16) inch in width. Seam type EFb-1, stitch type 301."

c. Place a 3/8 (+1/16) inch horizontal bartack superimposed on the stitching across facing width at the top of sleeve opening.”

Page 3, paragraph 3.1.2, Line 6, delete "1/2-inch size tack and 30 (± 2) stitches per tack" and substitute "1/2-inch long, 1/16-inch wide size tack with 28 (± 2) stitches per tack."

Page 3, paragraph 3.1.7, delete and substitute:

"3.1.7. Bartacks. Bartacks shall be stitched and positioned as indicted in Table I-1. When counting the stitches in the bartack construction, the lay stitch shall be included. Bartacks shall be free from thread breaks loose stitching."

TABLE I-1. Bartacks

Bartack Location

fastener tape Horizontal bartack on top folded ends of slide fastener tape

pocket Vertical bartack at lower corner of front lower patch pocket opening

pocket Horizontal bartack at upper corner of front lower patch pocket opening

sleeve Horizontal bartack across seam allowance at top of sleeve opening

flap Vertical bartack superimposed on inner row of stitching on bottom corner of all pocket flaps

for pencil pocket opening

Page 4, Paragraph 3.2. 3, After line 4 add:: "The cloth shall be products that are authorized by the certifying activity for listing on the applicable source control drawing, NCTRF Drawing 01-NCTRF-17, before contract award (see 7.5). Unless otherwise specified in the contract the certification sample yardage shall be 5 yards. The cloth shall be certified through inspection and examination for the cloth salient characteristics specified in this document when tested as specified in 3.2.3, 3.2.3.1 and Table I. The certification inspection shall be unacceptable if the requirements are not met."

Page 4, Table I, Row 2, Delete: "7.0" and "8.0" from Type II, Class 1, Color C requirements and replace with: "See drawing 01-NCTRF-17"

Page 5 and 6, Delete Flame Resistance Row 10 entire block and Flame Resistance Row 1 entire block and replace with

Flame Resistance, Initial After Flame, seconds (maximum) After Glow, seconds (maximum) Char Length, inches (maximum)

2.0

2.0

5.0

2.0

25.0

5.0

Flame Resistance, After 25 home launderings After Flame, seconds (maximum) After Glow, seconds (maximum) Char Length, inches (maximum) AATCC-135, 1, V, Ai & ASTM D6413

N/A

2.0

2.0

5.0

2.0

25.0

5.0

Page 6, paragraph 3.2.4, line 4 delete "or "good".

Page 7, paragraph 3.2.6, line 3, delete "minimum".

Page 9, paragraph 3.4, line 6, delete " The top and side of the pocket flaps, the" and substitute "The top and side edges of the pocket flaps shall be double stitched 1/16-inch from folded edge with a 1/4-inch gauge. The".

Page 15, paragraph 5.2, End item examination Line 2, after "MIL-STD-1668" delete "except that table I shall not be used. Lots of coveralls shall be sampled as defined by contract, except where otherwise indicated."

Page 17, Paragraph 7.5, At end of paragraph, add new entry:

"f. When certification is required; name and address of certification activity (see 3.1.1 and 4.2.1)"

Page 17, Under "MILITARY INTERESTS" delete and substitute:

"Preparing Activity:

Navy-NU

Custodians:

Navy-NU

DLA-CT"

LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

a. This solicitation/award consists of the following documents, exhibits, and other attachments

b. DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements dated October 2018, which has superseded DSCPM 4155.3, QUALITY SYSTEMS REQUIREMENTS, dated NOVEMBER 3, 1997.

c. DLA Troop Support Clothing and Textiles Additional Quality Assurance Requirements dated October 2018 additional changes:

Page 10 of 38, par. 2.1, line 4, after "(DCMA QAS)" add ", or Supplier's Source Sampling Representative, as applicable"

Page 11 of 38, par. 2.3, line 2, delete "to the source QAS". Line 4, delete "source QAS" and replace with "Supplier's Source Sampling Representative". Page 12, par 2.3 (continued), delete "source QAS" and replace with "Supplier's Source Sampling Representative".

Page 12 of 38, par. 2.4, line 5, delete "as required" and replace with "if required".

Page 12 of 38, par. 3.1.1, after "entirely" add the following: "For routine shade or physical testing of fabric lots, Government sampling is not required. The DD Form 1222 for routine shade or physical testing of fabric lots shall be signed and dated by the Supplier's Source Sampling Representative in Box 15."

Page 13 of 38, par. 3.1.2 - line 10, after "Government QAS" add the following: "or Supplier's Source Sampling Representative, as applicable,"

Page 14 of 38, par. 3.2.1 -line 4, delete "source QAS" and replace with "Supplier's Source Sampling Representative".

Page 14 of 38, par. 3.2.1.1 - cutting swatches, delete "DCMA QAS" and replace with "Supplier's Source Sampling Representative". After "single color rolls - 4"x 24"" delete "QAS" and replace with "Supplier's Source Sampling Representative". After "multi-color camouflage"... delete "QAS" and replace with "Supplier's Source Sampling Representative".

Page 14 of 38, par. 3.2.1.2 - line 3, delete "stamped,". Line 4, Delete "source QAS" and replace with "Supplier's Source Sampling Representative"

Page 15 of 38, par. 3.2.1.4 - subpar. 2, delete "source QAS" and replace with "Supplier's Source Sampling Representative"

Page 15 of 38, par. 3.2.2 - Line 3, delete "stamped,", delete "source QAS" and replace with "Supplier's Source Sampling Representative". Line 4, delete "QAS" and replace with "Supplier's Source Sampling Representative".

Page 16 of 38, par. 3.3.1 - Line 2, after "(30)" add, "calendar". Line 3 and Line 6, after "QAS" add, "or Supplier's Source Sampling Representative"

Page 16 of 38, par. 3.3.2 - Delete the paragraph in its entirety, including subparagraphs labeled "a" through "i", and replace with the following:

"3.3.2. Contractor Furnished Material (CFM). DLA Troop Support Clothing and Textiles contracts require source sampling of CFM at finishing plants. The following provisions apply to sample selection and lot acceptance.

(a) The samples shall be randomly selected by the Supplier's Source Sampling Representative.

(b) Upon presentation of a lot, the Supplier's Source Sampling Representative will draw samples and forward the samples to the contractor's laboratory specified in the contract for testing.

(c) Shipment of Component Lots from the source to the prime contractor need not be deferred except for Government Acceptance Testing (i.e., shade evaluation). Commencement of production prior to receipt of a passing test report from the contractor's authorized laboratory is solely at the contractor's risk.

(d) The contractor will provide copies of Certificates of Compliance to the QAS.

(e) The contractor is required to ensure that a complete test report for all lots is furnished to the source's QAS and the appropriate DLA-PTC representative."

Pages 24, 25, 36 add to block 16: "By signing in box 15, I certify that the samples referenced above were randomly selected and represent the lot identified above.

**Special note: Contractors shall ensure that blocks 2 and 15 of the form DD1222 are updated to reflect the correct information. Historically, both blocks contained the information of the DCMA QAR and their stamp/signature. When contractor's representative samples, these blocks shall include the contractor's representative's information. Block 17 shall still include the DCMA QAR to receive the results of the report even though they may not be sampling the material to be tested.

[End of interim changes.]

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20" AND REPLACE "MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR A-A-50198A

THREAD, GIMP, COTTON, BUTTONHOLE

STANDARD SAMPLE FOR COLOR FOLIAGE GREEN 504,

IS MIL-C-44436, ROLL #3728, (THE FOLIAGE GREEN

502 AREA PF THE PATTERN) AND REFERENCE

FOR SHADE ONLY.

AATCC 61 COLORFASTNESS TO LAUNDERING, HOME

. AND COMMERCIAL, ACCELERATED.

AATCC 169 WEATHER RESISTANCE OF TEXTILES:

. XENON LAMP EXPOSURE

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO

AMERICAN SOCIETY FOR TESTING AND MATERIALS,

1916 RACE STREET, PHILADELPHIA, PA 19111-1187.

INTERIM CHANGES TO A-A-55126B,

THE FOLLOWING CHANGES ARE FOR ALL CURRENT, PENDING AND FUTURE PROCUREMENTS OF THE SUBJECT DOCUMENT UNTIL SUCH TIME AS THE DOCUMENT IS AMENDED OR REVISED.

PAGE 4. TABLE I, PHYSICAL REQUIREMENTS, CHARACTERISTIC, SHEAR STRENGTH,DELETE LBS/SQ INCH (MIN), ADD SHEAR STRENGTH, LBS/2 SQ INCH (MIN).

PAGE 5 TABLE II, PHYSICAL REQUIREMENTS; CHARACTERISTIC, LENGTH

DIMENSIONAL STABILITY, % (MAX); LOOP, ALL CLASSES DELETE .0; ADD ALL CLASSES 4.0.

PAGE 7, Paragraph 3.10.2, Change the following title of paragraph from: "Fray resistance of Universal Camouflage Shades" and replace with "Fray resistance of Camouflage Prints"

PAGE 14, Paragraph 7.3.4 Change the following title of paragraph from: Fray resistance for Universal Camouflage Shades." and replace with "Fray resistance for Camouflage Prints."

ADDITIONAL INFORMATION FOR MIL-STD-1668:

INTERIM CHANGES TO MIL-STD-1668B ARE AS FOLLOWS:

PAGE III, IN THE FORWARD ADD TO THE BOTTOM OF

THE LIST OF SPECIFICATIONS THAT WILL REFERENCE

THIS STANDARD:"MIL-C-24945 - COVERALLS, FLAME

RESISTANT (COTTON FRONT)"

PAGE 12, TABLE II, CLASSIFICATION OF DEFECTS,

TABLE XIII, LABEL(S) AND SYMBOL(S), DELETE

THE TITLE AND SUBSTITUTE "LABELS/BAR CODE".

AND ADD THE FOLLOWING NEW DEFECTS;

"E. BAR CODE LABEL:

LABEL/TAG

BAR CODE OMITTED OR NOT READABLE BY

SCANNER 1

HUMAN READABLE INTERPRETATION (HRI)

OMITTED OR ILLEGIBLE 1

NOT VISIBLE ON FOLDED, PACKAGED ITEM 1

CAUSES DAMAGE TO THE ITEM 3

ASTM D 3776 MASS PER UNIT AREA (WEIGHT)

. OF WOVEN FABRIC

. 3 OCTOBER 1994.

AATCC 8 CHROMATIC TRANSFERENCE SCALE

AATCC 15 COLORFASTNESS TO PERSPIRATION

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)

PACKAGING

Case Lot is 30 Coveralls, of one size only, packed in each carton.

As a minimum item shall be packed in a snug fitting fiberboard shipping container conforming to ASTM-D-5118, Type CF, Style RSC, Grade 275, variety SW, Class domestic, with a double wall liner. Any commercial closure method cited in ASTM-D-1974 is acceptable except stapling.

Packaging shall be as per ASTM-D-3951, MIL-STD-129 with change notice 4, MIL-STD-147. Lot numbering shall be in accordance with MIL-STD-129 AND DSCP-4155.3

Packaging examination. The fully packaged end item shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.

Examine Defect

Marking Omitted; incorrect; illegible, of (exterior) improper size, location, sequence & Unit Pack, or method of application.

Materials Any component missing, damaged or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling. Bulged or distorted container.

Contents Number of intermediate containers per shipping container is more or less than required.

Number of items per container is more or less than required.

Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged.

The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5.

Examine Defect

Finished Length, width or height exceeds Dimensions specified maximum requirement.

Palleti- Pallet pattern not as specified.

zation Interlocking of loads not as specified. Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted; incorrect; illegible;

of improper size, location, sequence or method of appli-cation.

MIL-STD-129R - DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED 18 FEBRUARY 2014

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E

w/CHANGE 1 23 December 2013

SUPERSEDING

MIL-STD-147E

16 May 2008

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS