TECH DATA PGC 18243 CLOTH TROPICAL BLUE 3346 .pdf

CLOTH, TROPICAL: POLYESTER AND WOOL,BLUE 3346

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL

AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE

MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT

INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

9.5 TO 10.5 OZ/56 IN WIDTH, BLUE 3346, UNSPONGED, MOTHPROOF, HEATSET, WASHABLE. .

STANDARD SAMPLE IS ROLL NO. 10163 AND IS APPLICABLE FOR SHADE, FINISH, COLORFASTNESS.

ADDITIONAL INFORMATION FOR SPEC: MIL-C-24910B DATED 27 January 1992

THE CLOTH SHALL BE MOTHPROOFED IN ACCORDANCE

WITH MIL-C-43665C

CERTIFICATE OF CONFORMANCE IS APPLICABLE

FOR GRADING OF WOOL IN THE TOP FORM.

(Ref. 18243)

ADDITIONAL INFORMATION FOR MIL-C-43665:

INTERIM SPECIFICATION CHANGES TO MIL-C-43665C:

PAGE 2, PARA. 3.2, LINE 2, AFTER "TABLE 1 "

INSERT "OR TABLE 1A",

PAGE 3, TABLE 1, DELETE "SODIUM (4,5-DICHLORO,

2-CHLOROMETHANE SULFONAMIDO) 3',4'

6',TRICHLORO) DISHENYL ETHER (SEE 6.3.2) 0.26

0.60".

PAGE 3, AFTER TABLE 1, INSERT THE FOLLOWING NEW

TABLE:

"TABLE 1A, MOTHPROOFING COMPOUND.

. % ON WEIGHT OF WOOL

. MOTHPROOFING COMPOUND MIN. MAX.

EDOLAN ETS BEFORE DRYCLEANING

*(3-PHENOXYPHENYL) METHYL

PLUS OR MINUS CIS/TRANS 3-(2-,2-

DICCHLOROETHENYL)2,2-

DIMETHYLCYCLORPPANECARBOXYLATE. 0.058 0.40

CIS/TRANS RATIO:MAX.55% PLUS OR--AFTER DRY-CLEAN

MINUS CIS AND MIN.PLUS OR

MINUS TRANS.(*PERMETHRIN) 0.029 0.40

PAGE 3,PARA.3.4, LINE 3, AFTER "3.2" INSERT

"TABLE 1".

PAGE 3, AFTER PARA. 3.4 INSERT NEW PARAGRAPH AS

FOLLOWS:

"3.4.1 PERCENT OF MOTHPROOFING COMPOUND. THE

PERCENTAGES OF MOTHPROOFING COMPOUND SPECIFIED

IN TABLE 1A SHALL BE BASED ON WEIGHT OF PURE

COMPOUND ON THE WOOL FIBER CONTENT WHEN TESTED

BY HIGH PERFORMANCE LIQUID CHROMATOGRAPH (HPLC)

METHOD, OBTAINABLE FROM BAYER CORP., ROCK HILL,

SC 29732 (SEE 4.2.2)".

PAGE 5, PARAGRAPH 4.2.2,TABLE 11,DELETE THE

FOLLOWING:

CHARACTERISTIC REQUIREMENT TEST

. PARAGRAPH METHOD

"SODIUM (4,5-DICHLORO

2-CHLORO-METHANE

SULFONAMIDO)3',4',6',

TRICHLORO) DIPHENYL ETHER 3.4 4.3.1 3/ 4/"

AND SUBSTITUTE THE FOLLOWING:

CHARACTERISTIC REQUIREMENT TEST

. PARAGRAPH METHOD

"EDOLAN ETS

*(3-PHENOXYPHENYL 3.4.1 HPLC 7/

METHYL PLUS OR MINUS CIS/TRANS

3-(2,2-DICHLOROETHENYL)

2,2-DIMETHYL-CYCLOPROPANECARBOXYLATE

CIS/TTRANS RATIO: MAX.55%

PLUS OR MINUS CIS AND MIN.

PLUS OR MINUS TRANS.

*(PERMRTHRIN)"

PAGE 5, PARAGRAPH 4.2.2, FOR CHARACTERISTIC

EDOLAN ETS,UNDER TEST METHOD COLUMN, ADD

FOOTNOTE "7"/,ADD NEW FOOTNOTE "8"/.

PAGE 6, PARAGRAPH 4.2.2, TABLE II.AFTER FOOTNOTE

"7/",ADD THE FOLLOWING:"8"/ THE SAMPLE SHALL

BE DRY-CLEANED FOR THREE CYCLES IN ACCORDANCE

WITH AATCC TEST METHOD 86 BEFORE DETERMINING

MOTHPROOFING COMPOUND CONTENT.

PAGE 6, PARA.4.2.2, TABLE 11, AFTER FOOTNOTE 6/,

INSERT "7/ HIGH PERFORMANCE LIQUID

CHROMATOGRAPHY (HPLC) TEST METHOD MAY BE

OBTAINED FROM BAYER CORP., ROCK HILL, SC 29732."

PAGE 6, PARAGRAPHS 4.3,4.3.1,4.3.1.1,4.3.1.2,

4.3.1.3,4.3.1.4,4.3.1.5 DELETE PARAGRAPHS IN

THEIR ENTIRETY WITH NO REPLACEMENT.

PAGE 7, PARAGRAPHS 4.3.1.6, 4.3.1.7, 4.3.1.7.1

DELETE PARAGRAPHS IN THEIR ENTIRETY WITH NO

REPLACEMENT.

PAGE 8, PARAGRAPHS 4.3.1.7.2, 4.3.1.8, 4.3.1.8.1

DELETE PARAGRAPHS IN THEIR ENTIRETY WITH NO

REPLACEMENT.

PAGE 9, PARAGRAPHS 6.3 2, 6.4, 6.5, 6.6 DELETE

PARAGRAPHS IN THEIR ENTIRETY WITH NO

REPLACEMENTS.

PAGE 11, DELETE FIGURE 1 IN ITS ENTIRETY WITH NO

REPLACEMENT.

TABLE II, UNDER TEST METHOD: DELETE "2015" AND

SUBSTITUTE "2015.3"

NOTE! MITTEN FF CONC. SUPPLIED BY CIBA-GEIGY

CORP. P.O. BOX 11422, GREENSBORO, NC 27409

EDOLAN ETS, SUPPLIED BY MILES INC.,MOBAY ROAD,

PITTSBURGH,PA.15205-9741.

ARE APPROVED MOTH PROOFING AGENTS FOR

MILITARY FABRICS.

(Ref. T1118)

ADDITIONAL INFORMATION FOR MIL-I-45208:

NOTE: MIL-I-45208 HAS BEEN CANCELLED AND REPLACED BY THE FOLLOWING: INTERNATIONAL

STANDARDS ISO 9001:2008

OR AMERICAN SOCIETY FOR QUALITY ASQ 2008 VERSION.

(ref. T1286 )

ADDITIONAL INFORMATION FOR FED-STD-191:

FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO END ITEM SPECIFICATION FOR REPLACEMENT

ASTM.

INTERIM CHANGES TO FED-STD-191A:

TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE SPECIMEN

SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT ONE INCH OF SPECIMEN LIES WITHIN THE CLAMP AND ONE INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF THE VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE

OF THE DIAL PLATE".

TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA 4.1.2,LINE 4:

DELETE "B-97" AND SUBSTITUTE "B-91".

THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540, AND 1550. PARA 5.1 OF THESE TEST

METHODS REQUIRE THE USE OF 1,1,1- TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-

TRICHLORETHANE IS AN OZONE DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN

BASIC OR ANY REFERENCED DOCUMENT.

METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD. PAGE 2,

PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (INNER FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE

DIAL PLATE."

METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5, PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACK TEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60 MINUTES OR UNTILSAMPLES ARE

DRY IN A ROTATING TUMBLE DRYER."

PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND

BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING: "THE SPECIMENS AND BALLAST

SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACKTEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40

MINUTES OR UNTIL SAMPLES ARE DRY."

METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1, PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1, PARA. 4: DELETE "APPARTUS"

AND SUBSTITUTE "APPARATUS". PAGE 1, PARA. 5.1, LINE 3: AFTER "AT"

DELETE"APPROXIMATELY".

PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6: AFTER "TO" ADD "+-".

PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING IT OVER THE SENSOR OPENING. THE SURFACE OF THE TEST SPECIMEN (BACK OR FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE RESIDUAL CHARGE LEVEL ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY.

NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500 VOLTS YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A PERIOD OF 20 SECS. AT THE END OF THE 20 SECOND PERIOD, THE HIGH VOLTAGE (5000 VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS IMMEDIATELY GROUNDED. THE VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL BE PLOTTED ON THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL DISPLAY VOLTAGE AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT NECESSARY."

PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE SPECIMEN DID" IN ITS

ENTIRETY.

PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:

"RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND DECAY TIME TO 10% OF THE

MAXIMUM VOLTAGE LEVEL ACHIEVED."

PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE: "REVERSE VOLTAGE

POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS."

PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:

"THE AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL BE INCLUDED FOR EACH OF THE WARP & FILLING DIRECTIONS, AS WELL AS THE OVERALL AVERAGE, FOR EACHFABRIC TESTED.

THESE WILL BE OBTAINED BY AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS DOCUMENT, THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE MAXIMUM VOLTAGE IN BOTH THE WARP AND FILLING DIRECTIONS IS LESS THAN 4000 VOLTS, AND THE AVERAGE DECAY TIME (TO 10% MAXVOLTAGE) IS GREATER THAN 0.5 SECONDS IN BOTH THE WARP AND FILLING DIRECTIONS. IT

SHALL BE INDICATED WHETHER THE FABRIC ISACCEPTABLE OR NON-ACCEPTABLE."

PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE WITH "406D".

AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY FOR THE TEST."

(Ref. T0215)

ADDITIONAL INFORMATION FOR MIL-STD-655D:

INTERIM CHANGES TO MIL-STD-655D:

PAGE 3, PARA 4.1, ADD "QUALITY LEVEL 7"

PAGE 5, TABLE I, UNDER QUALITY LEVEL"7", ADD

UNDER ENTIRE SAMPLE "7 POINTS PER 100 SQ.

YARDS", ADD UNDER INDIVIDUAL ROLLS "10 POINTS

PER 100 SQ. YDS."

(Ref. T0319)

ADDITIONAL INFORMATION FOR MIL-STD-2073-1:

NO ADDITIONAL INFORMATION FOLLOWS

(Ref. T0898)

MIL-STD-1614A PROVISIONS FOR EVALUATING

. QUALITY OF CLOTH TYPE HOODS,

. 12/19/80