TECH DATA CLOTH PW M1 TROPICAL PGC 28380.pdf

CLOTH, TROPICAL, TYPE III, 60 INCH

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA

MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

WIDTH MINIMUM, KHAKI SHADE USMC-M1. STANDARD SAMPLE IS IDENTIFIED AS ROLL

NO 3875 AND IS APPLICABLE FOR SHADE, FINISH, HAND, PILLING, AND

COLORFASTNESS.

ADDITIONAL INFORMATION FOR MIL-C-29404:

CERTIFICATE OF CONFORMANCE IS APPLICABLE FOR THE

GRADING OF WOOL IN THE TOP FORM.

INTERIM SPECIFICATION CHANGES TO MIL-C-29404B.

PAGE 1, PARAGRAPH 1.2, CLASSIFICATION, DELETE "ENTIRE LINE

BEGINNING WITH TYPE I" AND ADD "TYPE III, TOP DYE 75/25

POLYESTER/WOOL, KHAKI SHADE M-1"

PAGE 1, PARAGRAPH 1.2 CLASSIFICATION, LINE 4: DELETE IN ITS ENTIRETY.

PAGE 3, PARAGRAPH 3.3.1.1.1 WOOL, LINES 2 AND 3; DELETE "NOT LOWER IN

GRADE THAN 62'S US. STANDARD FOR THE PIECE DYE".

PAGE 4, PARAGRAPH 3.3.2.1, POLYESTER/WOOL YARN, LINE 3: DELETE "SINGLES"

AND SUBSTITUTE "TWO-PLY YARNS."

PAGE 4, PARAGRAPH 3.3.2.1, POLYESTER/WOOL YARN. LINE 4: AFTER "FILLING",

DELETE REMAINDER OF PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE THE

FOLLOWING: "THE FINISHED TOP DYED CLOTH SHALL CONTAIN 75% POLYESTER +/-

3% AND 25% WOOL +/- 3% BASED ON THE OVEN-DRY WEIGHT, WHEN TESTED AS

SPECIFIED IN 4.5."

PAGE 4, PARAGRAPH 3.3.3, COLOR. DELETE THE PARAGRAPH IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING: "THE COLOR FOR THE TYPE III CLOTH SHALL BE

KHAKI SHADE M-1. THE COLOR SHALL BE OBTAINED BY TOP DYING ANS SHALL MATCH

THE STANDARD SAMPLE (SEE 6.3). THE COLOR OF THE SELVAGE SHALL APPROXIMATE

THE COLOR OF THE CLOTH."

PAGE 4, PARAGRAPH 3.3.3.1, MATCHING, LINES 2, 5 AND 6; DELETE "I OR TYPE

II" AND SUBSTITUTE "III".

PAGE 4, PARAGRAPH 3.4.1, PHYSICAL REQUIREMENTS. TABLE I: UNDER

TABLE I ADD "NEW COLUMN AT BEGINNNG OF DESCRIPTION COLUMNS "TYPE" IN TYPE

COLUUMN ADD "TYPE II" FOR THE EXISTING PHYSICAL

REQUIREMENTS AND ADD "TYPE III" WITH THE FOLLOWING PHYSICAL

REQUIREMENTS "YARNS PER INCH, MINIMUM WARP 55, FILLING 47" AND THE

REMAINING REQUREMENTS APPLY TO BOTH TYPES.

PAGE 4, 3.4.1, PHYSICAL REQUIREMENTS. TABLE I: UNDER THE COLUMN HEADED

"YARNS PER INCH", UNDER "WARP" DELETE "65" AND SUBSTITUTE "55" AND UNDER

"FILLING" DELETE "59" AND SUBSTITUTE "47".

PAGE 5, PARAGRAPH 3.5, WEIGHT OF CLOTH. DELETE THE FOLLOWING: "PIECE DYED

CLOTH (OUNCES) MINIMUM 6.5 MAXIMUM 7.0"

PAGE 5, PARAGRAPH 3.5, WEIGHT OF CLOTH, UNDER THE HEADING "TOP DYED CLOTH

(OUNCES), UNDER "MINIMUM" DELETE "6.3" AND SUSTITUTE "8.1" AND UNDER

"MAXIMUM" DELETE "6.8" AND SUBSTITUTE "8.9".

PAGE 5 PARAGRAPH 3.6, LENGTH AND PUT-UP, LINE 4: DELETE "PPP-P-1132" AND

SUBSTITUTE "ASTM-D-3951".

PAGE 7, PARAGRAPH 4.4.2.1, YARD-BY-YARD EXAMINATION.

LINE 1: AFTER "YARD-BY-YARD EXAMINATION" INSERT "THE YARD-BY-YARD

EXAMINATION SHALL BE AS SPECIFIED IN MIL-STD-655."

PAGE 7, PARAGRAPH 4.4.2.1, YARD-BY-YARD EXAMINATION, LINE 5: AFTER

"EXAMINED.", INSERT "THE QUALITY LEVEL FOR THE CLOTH SHALL BE 12."

PAGE 8, PARAGRAPH 4.4.2.1, YARD-BY-YARD EXAMINATION, FOOTNOTE 1/, LINE 4,

AFTER "SAMPLE" ADD "IF ONE ROLL OF CLOTH EXCEEDS THE POINT LEVEL, A

SECOND SAMPLE SHALL BE EXAMINED ONLY FOR INDIVIDUAL ROLL QUALITY

EXAMINATION. THE LOT SHALL BE UNACCEPTABLE IF ONE OR MORE ROLLS IN THE

SECOND SAMPLE EXCEEDS THE POINT LEVEL."

PAGE 8, AFTER PARAGRAPH 4.4.2.5, ADD THE FOLLOWING NEW PARAGRAPH:

"4.4.2.6 LIMITS OF SLUBS ANS KNOTS. ONLY SLUBS AND KNOTS WHICH EXCEED

"D" FOR SLUBS AND "C" FOR KNOTS ON THE SEARS FABRIC DEFECT SCALE SHALL BE

SCORED (SEE 6.9)."

PAGE 9, TABLE III, TEST METHODS. DELETE ALL REFERENCES TO "TYPE I" AND

SUBSTITUTE "TYPE III". DELETE IN THEIR ENTIRETY ALL REFERENCES TO "TYPE

II".

PAGE 11, PARAGRAPH 5.1, PUT-UP AND PACKAGING. LINES 1 AND 2: DELETE

"LEVEL 1 OR".

PAGE 12, PARAGRAPH 5.1.1, LEVEL A AND COMMERCIAL. LINE 1: DELETE "LEVEL A

AND". LINES 2 AND 3. DELETE "PPP-P-1132" AND SUBSTITUTE "ASTM-D-3951".

PAGE 12, PARAGRAPH 5.2, PACKAGING, LINE 1: DELETE "LEVEL A OR".

PAGE 12, PARAGRAPH 5.2.1, LLEVEL A AND COMMERCIAL.

LINE 1: DELETE "LEVEL A OR". LINE 2: DELETE "PPP-P-1132", AND SUBSTITUTE

"ASTM-D-3951"

PAGE 12, PARAGRAPH 6.2, ACQUISITION REQUIREMENTS. C., LINE 1: AFTER

"REQUIRED" DELETE THE SECOND SENTENCE IN ITS ENTIRETY AND SUBSTITUTE

"SPECIFY NUMBER AND TEXTURE (SEE 1.2 AND 3.5)."

PAGE 13, PARA. 6.5, ACCEPTANCE CRITERIA. FOURTH LINE. DELETE

"20" AND ADD "12". SIXTH LINE. DELETE "33" AND ADD "18".

PAGE 13, INSERT THE FOLLOWING NEW PARAGRAPH: "6.9 SEARS FABRIC DEFECT

SCALES ARE AVAILABLE FROM SEARS, ROEBUCK AND COMPANY, DEPARTMENT 87

(ATTENTION: BSC-23-29), "FABRIC DEFECTS REPLICA KIT", CHICAGO, IL, 60694

INCLUDE T1721 OBJECT TEXT ID ST

ADDITIONAL INFORMATION FOR MIL-I-45208:

NOTE: MIL-I-45208 HAS BEEN CANCELLED AND REPLACED BY THE FOLLOWING:

INTERNATIONAL STANDARDS ISO 9001:2008

OR AMERICAN SOCIETY FOR QUALITY ASQ 2008 VERSION.

(ref. T1286)

ADDITIONAL INFORMATION FOR FED-STD-191:

FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW

DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO END ITEM

SPECIFICATION FOR REPLACEMENT ASTM.

INTERIM CHANGES TO FED-STD-191A:

TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE

SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE

OF THE VISE, SUCH THAT ONE INCH OF SPECIMEN LIES WITHIN THE CLAMP AND ONE

INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF THE

VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE".

TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA

4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91".

THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING

SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540, AND

1550. PARA 5.1 OF THESE TEST METHODS REQUIRE THE USE OF 1,1,1-

TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-TRICHLORETHANE IS AN OZONE

DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE

USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN

BASIC OR ANY REFERENCED DOCUMENT.

METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD.

PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE

FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH

THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE

CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (INNER

FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL

PLATE."

METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5,

PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND

BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE

SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED

IN A PRE-HEATED DRYER HAVING A STACK TEMPERATURE OF 140-180 DEG. F. THIS

TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE

INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60 MINUTES OR

UNTILSAMPLES ARE DRY IN A ROTATING TUMBLE DRYER."

PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE

SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING:

"THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND

PLACED IN A PRE-HEATED DRYER HAVING A STACKTEMPERATURE OF 140-180 DEG. F.

THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE

TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40

MINUTES OR UNTIL SAMPLES ARE DRY."

METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1,

PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1,

PARA. 4: DELETE "APPARTUS" AND SUBSTITUTE "APPARATUS". PAGE 1, PARA.

5.1, LINE 3: AFTER "AT" DELETE"APPROXIMATELY".

PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6: AFTER

"TO" ADD "+-".

PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE

FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING

IT OVER THE SENSOR OPENING. THE SURFACE OF THE TEST SPECIMEN (BACK OR

FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE RESIDUAL CHARGE LEVEL

ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY.

NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500 VOLTS

YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A PERIOD

OF 20 SECS. AT THE END OF THE 20 SECOND PERIOD, THE HIGH VOLTAGE (5000

VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS IMMEDIATELY GROUNDED. THE

VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL BE PLOTTED ON

THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL DISPLAY

VOLTAGE AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT

NECESSARY."

PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE

SPECIMEN DID" IN ITS ENTIRETY.

PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH

THE FOLLOWING: "RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND

DECAY TIME TO 10% OF THE MAXIMUM VOLTAGE LEVEL ACHIEVED."

PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE:

"REVERSE VOLTAGE POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS."

PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH

THE FOLLOWING: "THE AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL

BE INCLUDED FOR EACH OF THE WARP & FILLING DIRECTIONS, AS WELL AS THE

OVERALL AVERAGE, FOR EACHFABRIC TESTED. THESE WILL BE OBTAINED BY

AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH

VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS DOCUMENT,

THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE MAXIMUM VOLTAGE

IN BOTH THE WARP AND FILLING DIRECTIONS IS LESS THAN 4000 VOLTS, AND THE

AVERAGE DECAY TIME (TO 10% MAXVOLTAGE) IS GREATER THAN 0.5 SECONDS IN

BOTH THE WARP AND FILLING DIRECTIONS. IT SHALL BE INDICATED WHETHER THE

FABRIC ISACCEPTABLE OR NON-ACCEPTABLE."

PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE WITH

"406D".

AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC

DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY FOR

THE TEST."

(Ref. T0215)

MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD PRACTICE

MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE

MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA

TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING

CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS

OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER

TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE

STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E w/CHANGE 2

27 JUNE 2019

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

ADDITIONAL INFORMATION FOR MIL-STD-655D:

INTERIM CHANGES TO MIL-STD-655D:

PAGE 3, PARA 4.1, ADD "QUALITY LEVEL 7"

PAGE 5, TABLE I, UNDER QUALITY LEVEL"7", ADD

UNDER ENTIRE SAMPLE "7 POINTS PER 100 SQ.

YARDS", ADD UNDER INDIVIDUAL ROLLS "10 POINTS

PER 100 SQ. YDS."

(Ref. T0319)

ADDITIONAL INFORMATION FOR MIL-STD-2073-1:

NO ADDITIONAL INFORMATION FOLLOWS

(Ref. T0898)