Tailgate_Spreaders_Brochure_122916_LowRes.pdf

Tailgate spreaders

U n d e r T a i l g a t e | R e p l a c e a b l e T a i l g a t e | S T C C | T A I L H A W K ™

Matching performance requirements with application needs is critical to selecting the right tailgate spreader. Swenson’s line of tailgate spreaders is uniquely designed to work seamlessly with all standard dump body tailgates. Whether you use finer materials like salt and sand, or larger material like gravel and rock, our equipment can handle the job. Improve the efficiency of the equipment by adding a spray system. Since 1937, Swenson has been the leader in providing quality, dependability and durability in snow and ice control. When you are looking for tailgate spreaders, Swenson has the solution for your work trucks!

QUALITY.

DEPENDABILITY.

DURABILITY.

U n d e r T a i l g a t e | R e p l a c e a b l e T a i l g a t e | S T C C | T A I L H A W K ™ swensonproducts.com

TA

ILG

AT

E

SP

RE

AD

ER

S

CHOOSING THE RIGHT

TAILGATE SPREADER

FOR THE JOB

Replaceable Tailgate

vs. Undertailgate

If the distance from the ground to the floor of the dump bed is less than 44”, then the Swenson Replaceable Tailgate Spreader is right for your truck. Replaceable

Tailgate Spreaders are designed to replace the entire tailgate for applications where the distance from the ground to the bottom of the tailgate limits the use of an undertailgate spreader. When the distance from the ground to the floor of the dump bed is more than 44”, then choose a model from the S Series line of undertailgate spreaders. These units have height adjustable spinners and are designed to install below the existing tailgate, providing a variety of spreading solutions. The S Series is available in multiple configurations, as shown here.

swensonproducts.com

S Series Drive Options

Swenson offers three types of drive systems. All drive systems have their own unique advantages to match to your specific requirements.

Direct Drive �Higher performance

�Lower maintenance costs

Gearbox Drive �Better control at low spread rates

�Incorporated through-shaft provides convenient spread rate sensor mounting

Electric Drive �Separate electric motors allow independent control of the auger and spinner

�Uses existing electric system

S-Series Selection Guide

Swenson makes choosing the right S-Series spreader for your application a snap. Use the information and the chart below to determine which Swenson Tailgate Spreader is best suited for you:

MODEL

SPREAD RATE

LBS/REV

PRIMARY

USE

DROP PORT

LOCATION

SPINNER VISIBLE

IN SIDE MIRROR SPECIAL FEATURES

SAD 15 Urban Even unloading for better truck stability

SBD-6 6 Urban Optimal for two-lane spreading

SBD-9 21 Rural Optimal for two-lane spreading and larger material

SCD 11 Urban Even unloading for better truck stability

SEL 15 Urban Eco-friendly electric Fits dump beds 44” and up

RTEL 6 Urban

Not Visible

Visible

Visible

Visible

Visible

Not Visible

Middle Left

Left or Right

Left

Left or Right

CENTER

OR MIDDLE LEFT

CENTER

OR LEFT

Eco-friendly electric Fits dump beds under 44” high

SEL ELECTRIC

UNDERTAILGATE

SPREADER

Equipment Size 96” w x 19” h x 18” d

Weight, empty 455 lbs

Auger 6” diameter steel

Trough construction 10 ga. powder-coated carbon steel or 10 ga. corrosion-resistant stainless steel

Spinner disk 18” poly

Spread width 4’ to 40’

Port locations 21” from left or right ends

Amperage draw 100 amps total

Safety features Electric Interlock System

Warranty 1 year

Options Center drop, left end drop, vibrator kit, pre-wet system

Highlights

� Designed for trucks 15,000 lbs.+ GVW with ground clearances 44” and up.

� Mounts below dump body bed to allow for normal dumping operations when spreader is not in use.

� Uses your truck’s electrical system – no expensive central hydraulics needed.

� Separate electric motors provide independent control of auger and spinner.

� Anti-flow plate prevents material free-flow and helps minimize material waste.

� 6” auger with continuous/reverse fliting for unloading on both sides of vehicle

� 18” poly spinner disk

� Hinged cover allows full use of dumping operations while spreader is mounted on truck.

� Electric Interlock System (EIS) permits disabling of auger when opening bottom door or top cover.

� Dual speed variable controller provides independent control of auger and disk.

Materials Salt

Salt / sand mix*

Magnesium chloride

Treated rock salt

Clear Path Ice Melt

Patent pending Electric Interlock System disables auger when cover is opened.

Variable speed controller allows independent control of auger and spinner.

Stainless steel ½ hp auger motor.

Anti-flow plate prevents material free flow and helps minimize material waste.

QR CODE

HERE

SE

L

*Not recommended for straight sand.

Spreader Port Locations Left port

Center port swensonproducts.com

SAD/SBD-6 HYDRAULIC

SPREADER

Equipment Size 96” w x 19” h x 18” d

Weight, empty 540 lbs

Auger 6” diameter steel

Trough construction 10 ga. corrosion-resistant stainless steel or 7 ga. powder-coated carbon steel

Port locations SAD – 21” from left end; SBD-6 – extreme left or right ends

Safety features Hydraulic Interlock System

Warranty 1 year

Options Vibrator kit, liquid spray systems, central hydraulic hose kit, dual flow control valve, central hydraulic 7 gal. tank kit

Highlights � Designed for trucks 15,000 lbs.+ GVW with ground clearances greater than 44”.

� Unit mounts below dump body floor to allow normal dump body operations when spreader is not in use.

� Available with direct driven or gearbox driven auger motor.

� Separate hydraulic motors for auger and spinner ensures better control and spreading.

Material drop port is 21" from left end plate

� 6” auger with continuous/reverse fliting

� 18” poly spinner disk

� Anti-flow plates save material by preventing free-flowing of material

� Quick detach stabilizer kit keeps spinner parallel to the road at all dump angles.

� Hinged bottom door makes clean out and blockage removal easy.

� Hydraulic Safety Interlock system disables auger when opening bottom door or top cover.

� Ideal for salt/aggregate mixture.

Anti-flow plate helps prevent free-flow of material

Direct drive motor drives 6” auger Safety interlock disables auger when opening bottom door or top cover.

Materials Salt

Sand

Salt / sand mix

Magnesium chloride

Treated rock salt

Clear Path Ice Melt

QR CODE

HERE

Spreader Port Locations

SAD

(21" from end)

SBD-6

(extreme ends)

Left Middle

Left or Right swensonproducts.com

SA

D/

SB

D-

SBD-9 HYDRAULIC

SPREADER

Equipment Size 96” w x 19” h x 18” d

Weight, empty 600 lbs

Auger 9” diameter steel

Trough construction 7 ga. powder-coated carbon steel or 10 ga. corrosion-resistant stainless steel

Spinner disk 18” poly

Spread width 4’ to 40’

Port locations Extreme left or right ends

Safety features Hydraulic Interlock System

Warranty 1 year

Options Vibrator kit, liquid spray systems, dual flow control valve, central hydraulic 7 gal. tank kit, right hand spinner assembly

Highlights � Designed for trucks 15,000 lbs.+ GVW with ground clearances greater than 44”.

� Unit mounts below dump body floor to allow normal dump body operations when spreader is not in use.

�Direct driven auger motor provides higher performance and lower.

� Separate hydraulic motors for auger and spinner ensure better control and spread-ing.

� Material drop port is at extreme left or right ends for discharge on either side.

� 9” auger designed to spread larger ag-gregate or higher volumes of material at either end.

� 18” poly spinner disk

� Anti-flow plates save material by preventing free-flowing of material.

� Quick detach stabilizer kit keeps spinner parallel to the road at all dump angles.

� Hinged bottom door makes clean out and blockage removal easy.

� Hydraulic Safety Interlock system disables auger when opening bottom door or top cover.

� Includes 24” berm chute for shoulder applications.

� Ideal for salt/aggregate mixture.

Hydraulic Interlock prevents opening of bottom door or top cover.

Anti-flow plate prevents material free flow and helps minimize material waste. Spreader Port Locations

Left port Right port

Materials Sand

Salt / sand mix

Magnesium chloride

Treated rock salt

Clear Path Ice Melt

*Unit moves high volume material.

swensonproducts.com

SB

D-

RTEL

REPLACEABLE TAILGATE

ELECTRIC SPREADER

Highlights

� Designed to replace the existing tailgate on dump trucks 15,000 lbs+ GVW.

� Uses your truck’s electric system – no expensive central hydraulic system is needed.

� Separate electric motors provide inde-pendent control of auger and spinner.

� Anti-flow plate prevents material free-flow and helps minimize material waste.

� 6” auger with continuous fliting for un-loading on both sides of vehicle

� 18” poly spinner disk

�� Hinged bottom cover for easy clean out or blockage removal

� Electric Interlock System (EIS) disables auger and spinner when opening bottom door or top cover.

� Dual speed variable controller provides independent control of auger and disk.

� Mounting kit with 11/4” hinge pins works with variety of dump bodies.

Equipment Size (88”, 96”) w x 23” h x 16.5” d

Weight, empty 395 lbs

Auger 6” diameter steel

Trough construction 10 ga. powder-coated carbon steel or 10 ga. corrosion-resistant stainless steel

Spinner disk 18” poly

Spread width 4’ to 40’

Port locations 4-1/2” from left end; center drop available

Amperage draw 100 amps total

Safety features Hydraulic Interlock System

Warranty 1 year

Options Center drop, vibrator kit, pre-wet system

Electric Interlock System prevents opening of bottom door.

Variable speed controller allows independent control of auger and spinner.

½ HP stainless steel electric auger motor.

Spreader Port Locations Left port

Center port

Materials

*Not recommended for straight sand.

swensonproducts.com

RT

EL

Highlights

�Low-maintenance poly spreader offers various mounting options to fit wide range of vehicles.

� 12 V direct drive, high torque motor works through large chunks of material.

� Blast mode provides on-command surge to grind through harder chunks.

� In-cab controller is easy to operate.

� One-piece cover allows for easy filling.

� Two hopper capacities available.

�All frame components are powder coated to last longer.

�Optional top screen eliminates large chunks of material from entering hopper and improves material flow.

Tailhawk

Equipment Tailhawk 350 Tailhawk 750 Size 35.5” h x 49” w x 30” d 35.5” h x 49” w x 30” d

Weight, empty 150 lbs 230 lbs

Operating system 12 V direct drive, high torque motor

12 V direct drive, high torque motor

Construction Molded orange poly with powder coated steel frame

Molded orange poly with powder coated steel frame

Capacity 5.75 cu.ft. 10.75 cu.ft.

Spread width 3 to 20 feet 3 to 20 feet

Warranty 1 year 1 year

Options 3-point mount, receiver hitch mount optional lightbar, optional legstands

3-point mount, receiver hitch mount optional lightbar, optional legstands

1/2 HP Direct Drive Motor links directly to the auger providing maximum power.

Optional Flow Kit can be adjusted to set the flow rate.

Variable Speed Controller for precise spreading of material.

When you need to respond quickly to a storm, or have smaller areas to tend to such as parking lots or private communities, the

Swenson TAILHAWK Spreader is the perfect choice.

Available in two sizes, these durable poly spreaders will handle salt, sand or other granular materials. Equipped with the most powerful spreader motor available, its ½ hp direct drive motor produces up to 70 amps of surge power and includes a Fast Blast feature that powers through chunks of material.

*Some require optional equipment.

swensonproducts.com

TA

ILH

AW

K

Materials

Equipment Size 102” l x 33” h x 32” d

Weight, empty 1,100 lbs

Trough construction 10 ga. powder-coated carbon steel or 10 ga. corrosion-resistant stainless steel

Operating system Central hydraulics with 2,000 psi flow rate

Spinner disk 18” poly

Spread width 4 to 40 ft., 240 tons/hr.

Drop locations Feed gates on each end

Safety features Hydraulic Interlock System

Warranty 1 year

Options 4-foot motorized extension, light bar, leg stands, reversing valve, spinner assembly

Highlights

� Designed for trucks Class 7+ (26,001+ lbs

GVW).

�� Ideal for year-round use including:

• Trench filling

• Road sanding

• Shouldering

• Asphalt Patching

� 102” trough fits standard width dump bodies.

�14” wide, high temp belt over chain handles a variety of materials on either side of truck.

� High temp belt sealers prevent material buildup.

� Hinged top cover

� Screw-type gate jacks provide precise material output adjustment, even when loaded.

� Quick detach 24” extension helps position material outside of truck tire path.

� Dual 11” x 14” manually adjustable feed gates allow material discharge from either side of truck.

� Includes stabilizer kit with mounting hardware to keep unit parallel to road during spreading.

� Swenson recommends the installation of LED light kit #00002-037-35 as the STCC blocks frame-mounted ID lights.

STCC

Cross Conveyor

Spreader The Swenson Tailgate Cross

Conveyor provides for the most efficient method of distributing granular materials available today. This sturdy cross conveyor will perform dozens of jobs while saving on labor, time, and material.

Heavy duty sprocket and shaft allows for consistent material flow.

Quick Detach 24" extension plate can be used on either side of conveyor.

Hinged top cover lays flat to allow for normal operations when not in use.

*Not recommended for straight salt.

Materials

swensonproducts.com

ST

CC

TAILHAWK 350 & 750

PV Electric Spreader

DRTEL Tailgate Spreader

SEL Electric UndertailgateVBEL Electric V-Box

Eco-Friendly Choices

Zero emissions from electric engines

� No polluting byproducts such as hydraulic fluids, oil and gas

� Powder-coated finishes have no volatile organic compounds (VOCs)

� Minimal noise emission as electric motors are virtually silent

At Swenson, we believe that the work truck equipment you use every day can actually help the environment. We guarantee that all Swenson stainless steel products contain a minimum of 60% recycled content. And when you choose one of our eco-friendly products, the environment will also benefit in these ways:

MDV Electric V-Box swensonproducts.com

Swenson Engineering

Our engineering staff are truly world class, using the most advanced design equipment available to continually improve our products, and lead in the development of new innovative ideas. Our team will work closely with you, asking questions about the work you need to do and the results you expect.

As the recognized leader in truck-mounted liquid and granular spreaders, plows and truck bodies for ice and snow control, we provide solutions for your work trucks.

*Liquid Spray Systems are available with either electric or hydraulic driven pump system, and in various sizes designed to operate with other Swenson products.

OPTIONAL ITEMS S-SERIES R-Series TAILHAWK STCC

Dual Flow Control Valve X X X

Hydraulic Hose Kit X X X

Control Valve Stand X X X

Hydraulic Hoses, Pumps & Tanks X X X

Various Reservoirs X X X

Custom Color Paint X X X

Spinner Attachment (right hand) X X

Extension Kits for Taller Tailgate Replacement

X

Spray Systems* X

Spinner Guard Kit X

Direct Drive X

Gearbox Drive X

Stainless Steel X X X

4 Foot Motorized Extension X

Light Bar X

Storage Legs X

Spinner Assembly (Left Hand) X

Through Mount Spinner (TMS) X

Swing Away Mounting Kit X

3 Point Class I Hitch X

TAILGATE SPREADER OPTIONAL EQUIPMENT

Swenson Genuine Parts

If you want peak performance at all times, keep your Swenson equipment all Swenson.

For a complete list of Swenson replacement parts, contact our customer service team at

888-825-7323 or email sales@swensonproducts.com.

swensonproducts.com

Choosing the right spreader

Not sure which spreader is right for your needs?

Check out FIND MY PRODUCT at www.swensonproducts.com

/2

Sw en so n

Sp re ad er

L

LC

. P rin te d in U

.S .A

888.825.73234swensonproducts.com

Providing Solutions for Your Work Trucks

� Swenson offers a wide range of spreaders, dump bodies and liquid application equipment that can be customized to meet your exact needs.

4PV/MDV Spreaders – Poly, carbon or stainless in 6 to 10 feet.

4V-Box Spreaders – Hydraulic or electric in 8 to 22 feet.

4Tailgate Spreaders – Undertailgate and replaceable tailgate.

4Truck Bodies – Dump/Insert dump bodies in 6.5 to 15 feet.

4Liquid Systems – Anti-icers in 100 to 1,650 gallons. Pre-wet systems.

SWENSON GENUINE PARTS

When you want peak performance at all times, keep your Swenson equipment all Swenson.

For a complete listing of Swenson replacement parts, contact our customer service team.