STS021026_STS515_Altec_Ind.s_pricelist.pdf

Ohio STS Contract

1 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

Table of Contents

Aerial Units

37’ Telescopic Articulated Aerial Unit

37’ / 41’ / 48’ Telescopic Articulated Aerial Unit

50’ / 55’ / 60’ Telescopic Articulated Aerial Unit

50’ / 55’ / 60’ Non-Insulated Telescopic Articulated Aerial Unit

50’ / 55’ / 60’ Articulated Aerial Unit

50’ / 55’ / 60’ Articulated Over-Center Material Handler Aerial Unit

60’ Articulated Aerial Unit (City of Cleveland)

60’ Telescopic Articulated Aerial Unit (City of Cleveland)

60’/70’ Tree Care Articulated Aerial Unit

Digger Derricks

45’ / 47’ Standard Duty Derrick

50’ / 60’ Heavy Duty Derrick

41’ Backyard Derrick

50’ Digger Derrick (City of Cleveland)

Options

2 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

3 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

4 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

37’ Telescopic Articulated Aerial Unit AT37G Aerial Device

(picture is for reference only and may not have identical specifications)

Item Description Qty

Unit

1. ALTEC Model AT37G telescoping/articulating continuous rotation aerial device with an insulating articulating arm, insulating telescopic upper boom, and the patented ISO-Grip insulating system at the boom tip. Includes the following features:

A. Ground to bottom of platform height: 37.8 feet B. Working height: 42.8 feet C. Maximum reach to edge of platform. Side Mounted Platform: 26.6 feet. End Mounted

Platform: 28.3 feet (at 14.4 foot platform height).

D. Telescopic boom extension: 9 feet 8 inches E. Continuous rotation F. Insulating Aerial Device, ANSI Category C, 46kV and Below G. Articulating Arm: Articulation is from -7 to 90 degrees. Insulator provides 12 inches of isolation.

H. Compensation System: By raising the articulating arm only, the telescopic boom maintains its relative angle in relation to the ground. The work position is achieved through a single function operation.

I. Telescoping upper boom: Articulation is from -25 to 75 degrees.

J. Master/ Slave Leveling: Platform automatically maintains level during boom articulation through a lifetime master/slave hydraulic leveling system that requires no major preventive maintenance.

K. The INSULATING UPPER CONTROL SYSTEM includes a single handle controller incorporating high electrical resistance components that is dielectrically tested to 40 kV AC with no more than 400 microampers of leakage. The control handle is green in color to differentiate it from other non-tested controllers.

L. One set of tool outlets at the platform providing up to 5 gpm of flow for open center tools

5 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

M. Hydraulic System: Open center system operating at 5gpm and 2,400 psi.

N. Unit is painted with a powder coat paint process which provides a finish-painted surface that is highly resistant to chipping, scratching, abrasion and corrosion.

O. Structural Warranty all of the following applicable major components is to be warranted for so long as the initial purchaser owns the product: Booms, boom articulation links, hydraulic cylinder structures, outrigger weldments, pedestals, subbases and turntables.

P. Manuals: Two (2) operator and Maintenance/Parts manuals

2. AT37G Unit Model 1

3. Post style pedestal mounting 1

4. Poly Reservoir, Pedestal Mounted, 7 Gallon; Includes Sight Gauge. 1

5. Single, One (1) Man, Fiberglass Platform; End Mounted with 180 degree rotator. 24 x 30 x 42 inches, includes hydraulic tilt.

6. Two (2) Platform Steps 1

7. Platform Capacity, 400LBS. 1

8. Altec Patented ISO-Grip Insulating 4 Function, Proportional Speed, Upper Control Handle - with safety interlock and interlock guard. Forward/back operates upper boom in/out, tiller operates rotation CW/CCW, up/down operates upper boom up/down, and twist operates lower arm up/down. Platform leveling is controlled with a separate interlocked control handle.

9. Engine Start/Stop & Secondary Stowage System: 12 VDC powered motor and pump assembly for temporary operation of the unit in a situation where in the primary hydraulic source fails. Electric motor is powered by the chassis battery. This feature allows the operator to completely stow the booms and platform. Secondary Stowage & Start/Stop is activated with an air plunger at the platform and switch at the lower control station.

10. Manual lowering valve located at the boomtip. For use in emergency situations to allow the operator to lower the boom to the ground

11. Powder coat unit Altec White. 1

Unit & Hydraulic Acc.

12. HVI-22 Hydraulic Oil (Standard). 9

13. Standard Pump For PTO 1

14. Hot shift PTO for automatic transmission 1

6 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

Body

15. 108 Inch Universal Small Aerial Body for a 60 Inch CA Chassis with 38 Inch Long Side Access Tailshelf to Meet the Following Specifications:

A. Basic body fabricated from A40 grade 100% zinc alloy coated steel B. All doors are full, double paneled, self-sealed with built-in drainage.

C. Electro-zinc plated, steel hinge rods extend full length of door.

D. Door hinges are zinc alloy material attached with rivets E. All doors contain stainless steel, flush mounted, paddle activated rotary style latches with two-stage locking, including keyed locks and adjustable strikers.

F. Heavy-gauge welded steel frame construction with smooth galvaneal floor.

G. All edges are either rolled or folded for strength and safety H. Door header drip rail at top for maximum weather protection.

I. Neoprene or rolled fenders on wheel fender panels.

J. Steel treated for improved primer bond and rust resistance.

K. Automotive underseal applied to body.

L. Automotive type non-porous door seals fastened to the door facing.

M. 108 Inch Body Length N. 40 Inch Body Height (Standard) O. 94 Inch Body Width (Standard) P. 20 Inch Body Compartment Depth (Standard) Q. Body Color - White (Standard) R. Finish Paint Body At Body Manufacturer (Standard) S. 8 Inch Body Cross-members (Standard) T. No Treadplate On Compartment Tops U. 6 Inch tall wood tailboard installed at the rear of body cargo area V. No Compartment Lighting Supplied by the Body Manufacturer W. Stainless Steel Rotary Paddle Latch With Lock (Standard) X. Master Body Locking System (Standard) Y. No Chock Holders In Line Body Fender Panel Required (Standard) Z. Gas Shock Type Rigid Door Holders For Vertical Doors (Standard) AA. Chains On Horizontal Doors AB. Hotstick shelf extending full length of body on curbside.

AC. Drop-Down Hot Stick Door For One (1) Shelf (Right Side) AD. Two (2) Hot Stick Brackets AE. 1st Vertical Street Side (LH) - Two (2) Adjustable Shelf With Removable Dividers On 4 Inch

Centers

AF. 1st Horizontal Street Side (LH) - One (1) Fixed Shelf With Removable Dividers On 8 Inch

AG. Rear Vertical Street Side (LH) - Six (6) Adjustable Locking Swivel Hooks

7 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

AH. 1st Vertical Curb Side (RH) - Seven (7) Adjustable Locking Swivel Hooks, Louvered Panel

Installed in Cargo Wall

AI. 1st Horizontal Curb Side (RH) - Vacant AJ. Rear Vertical Curb Side (RH) - Two (2) Adjustable Shelf With Removable Dividers On 4

AK. Aluminum Rock Guards Installed at Bottom AL. 38" Tailshelf with Integrated Side Access Steps, Two Wheel Chock Holders, and Smooth

Galvaneal Floor Installed at Rear of Body

Body and Chassis Accessories

16. ICC Underride Protection 1

17. Combination 2 Ball (10,000 LB MGTW) And Pintle Hitch (16,000 LB MGTW) 1

18. Set Of Eye Bolts for Trailer Safety Chain, installed one each side of towing device mount. 1

19. Front Torsion Bar Installed On Chassis 1

20. Rear Torsion Bar Installed On Chassis 1

21. Install Counterweight As Needed 1

22. Platform Rest, Rigid with Rubber Tube 1

23. Boom Rest for a Telescopic Unit 1

24. Mud Flaps With Altec Logo (Pair) 1

25. Wheel Chocks, Rubber with Metal Hairpin Style Handle, 9.75'' L X 7.75'' W X 5.00'' H (Pair) 1

26. Small Grab Handle Installed At Rear 1

27. Slope Indicator Assembly For Machine Without Outriggers 1

28. 5 LB Fire Extinguisher With Light Duty Bracket, Installed Per DEPS 042 (In Cab or Inside Compartment Only)

29. Triangular Reflector Kit, Installed 1

30. Soft Vinyl Lanyard Pouch 1

31. Vinyl manual pouch for storage of all operator and parts manuals 1

8 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

Electrical Accessories

32. Lights and reflectors in accordance with FMVSS #108 lighting package. (Complete LED, including LED reverse lights)

33. Altec Standard Amber LED Strobe Light with Brush Guard - Post Mounted On Streetside Front

Compartment Top

34. 6-Way Trailer Receptacle (Pin Type) Installed At Rear 1

35. Electric Trailer Brake Controller (Tekonsha Voyager #9030) 1

36. Dash panel rocker switches supplied with Ford Chassis, 4 auxiliary switches supplied in up fitting package from Ford

37. Start/Stop/Throttle Module, 12 Volt System 1

38. PTO Indicator Light Installed In Cab 1

Finishing Details

40. Delivery Of Completed Unit 1

41. Inbound Freight 1

42. Altec Standard; Components mounted below frame rail shall be coated black by Altec. i.e. step bumpers, steps, frame extension, pintle hook mount, dock bumper mounts, D-rings, receiver tubes, accessory mounts, light brackets, under-ride protection, etc. Components mounted to underside of body shall be coated black by Altec. i.e. Wheel chock holders, mud flap brackets, pad carriers, boxes, lighting brackets, steps, and ladders.

43. Apply Non-Skid Coating to all walking surfaces 1

44. English Safety And Instructional Decals 1

45. Vehicle Height Placard - Installed In Cab 1

46. Dielectric test unit according to ANSI requirements. 1

47. Stability test unit according to ANSI requirements. 1

48. Placard, HVI-22 Hydraulic Oil 1

49. AT37G FA Installation 1

9 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

Warranty

50. Standard Altec Warranty: One (1) year parts warranty, one (1) year labor warranty, ninety (90) days warranty for travel charges, limited lifetime structural warranty

AT37G Standard Retail Price

$103,704.62

Ohio STS Discount -($7,407.47)

AT37G Ohio STS Price

$96,297.14

Description Add or Deduct Price

AT40G unit with 40’ height Add $13,004.29

Fixed 26” x 30” Fiberglass walk-in platform with door Add $2,512.86

Primary Outrigger, H-Frame, Flat-Shoe, In Lieu Of Torsion Bars Add $1,749.43

Primary Outrigger, H-Frame, Flat-Shoe, In addition to Torsion Bars

Add $3,882.86

60” Altec Fiberglass Body Add $11,065.71

84” Altec Fiberglass Body Add $17,507.14

Aluminum understructure with aluminum treadplate floor Add $2,125.71

Aluminum treadplate cargo wall liners and compartment tops Add $1,715.71

Platform Leveling At Lower Controls Add $488.57

84” CA Body, Extra Vertical Compartment Add $7,154.29

Remove Side Access And Add Vacant Vertical Compartment Deduct ($1,008.57)

Custom Color Above Rotation And Pedestal Add $3,714.29

Custom Color Body And Accessories Add $1,367.14

Rustproof Bottom Of Body Add $1,214.57

Gatorhyde Protection Paint, Cargo And Tailshelf Area Add $3,325.71

10 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

37’ / 41’ / 48’ Telescopic Articulated Aerial Unit AT41P Aerial Device

1. Altec Model AT41P Articulating Telescopic Aerial Device with a fiberglass upper boom and fiberglass insulator in the articulating arm and proportional joystick upper controls.

Built in accordance to ALTEC's standard specifications and to include the following features:

A. Ground to Bottom of Platform Height: 40.8 feet at 7.3 feet from centerline of rotation (12.45 m at 2.21 m)

B. Working Height: 45.8 feet (13.96 m) C. Maximum reach to edge of platform with Upper Boom Non- overcenter: 30.1 feet

(at 17.3 feet platform height)

D. Upper boom extension: 110 inches E. Continuous rotation F. Articulating Arm: Articulation is from -3 to 82 degrees. Insulator provides 19 inches of isolation.

G. Compensation System: By raising the articulating arm only, the telescopic boom maintains its relative angle in relation to the ground. The work position is achieved through a single function operation.

H. Upper Boom: Articulation is from -25 to 85 degrees. The fiberglass section provides a minimum of 10.9 inches of isolation in the upper boom (when retracted and 42.3 inches when extended).

I. Platform leveling is achieved by a hydraulic master-slave leveling system. This lifetime system is very low maintenance.

J. The dielectrically tested, insulating upper control system includes the following boom tip components that can provide an additional layer of secondary electrical contact protection.

11 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

Control Handle: A single handle controller incorporating high electrical resistance components that is dielectrically tested to 40 kV AC with no more than 400 microampers of leakage. The control handle is green in color to differentiate it from other non-tested controllers. The handle also includes an interlock guard that reduces the potential for inadvertent boom operation.

Auxiliary Control Covers: Non-tested blue silicon covers for auxiliary controls.

Control Console: Non-tested non-metallic control console plate.

Boom Tip Covers: Non-tested non-metallic boom tip covers. The covers are not dielectrically tested, but they may provide some protection against electrical hazards.

K. Hydraulic system: Open center (full pressure), maximum flow 6 GPM, maximum operating pressure 3,000.

L. Dielectric rating: Category C, 46 kV and below M. Unit is painted with a powder coat paint process which provides a finish-painted surface that is highly resistant to chipping, scratching, abrasion and corrosion.

Paint is electrostatically applied to the inside as well as outside of fabricated parts then high temperature cured prior to assembly ensuring maximum coverage and protection.

N. Manuals: Two (2) Operator’s and two (2) Maintenance/ Parts manuals containing instructional markings indicating hazards inherent in the operation of an aerial device.

O. Unit meets or exceeds ANSI 92.2 standards.

2. Pedestal 1

3. Steel Reservoir, 15 gallon capacity, triangular, 17'' L x 17'' W x 24'' H, and includes breather caps and dipsticks

4. Single 1-Man Platform, Fiberglass (Insulated), 24" x 30" x 42", End Mount, 180 Degree

Rotation

5. No Platform Elevator 1

6. Platform Mounted Single Handle Controls 1

7. No Jib/Winch 1

8. Two(2) Platform steps - located on the side of the platform nearest the elbow in the stowed position

9. Hydraulic Tool Circuit at Platform: One set of quick disconnect couplings at the boom tip for open center tools.

10. Engine Start/Stop & Secondary Stowage System: 12 VDC powered motor and pump assembly for temporary operation of the unit in a situation wherein the primary hydraulic source fails. Electric motor is powered by the chassis battery. This feature allows the operator to completely stow the booms, platform, and outriggers. Secondary Stowage & Start/Stop is activated with an air plunger at the platform or momentary switch at the lower control station and outriggers.

11. Slip Ring: Required for engine start/stop, secondary stowage system, and throttle control 1

12 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase options

12. Outriggers, Primary, Modified A-Frame with Integrated Subbase, 30"-34" Chassis Height, Electric Interlock, No Valves On Legs, 114" Spread, Fixed Shoe (AT37/41 M/P/S)

13. Electric Outrigger Controls, drive hydraulic outrigger control valves. Durable weather proof sealed electronic switches mounted in aluminum boxes located at the rear of the unit unless otherwise specified.

14. Lower Boom Tie Down 1

15. Altec Aerial Device Powder Painted White 1

16. HVI-22 Hydraulic Oil (Standard). 25

17. Standard Pump For PTO 1

18. Hot shift PTO for automatic transmission 1

19. Standard PTO/Transmission Functionality for Automatic Transmissions - If chassis is in gear, and PTO switch is activated, PTO will not engage. Chassis will remain in gear. Once the chassis is shifted back into gear the PTO will disengage. For some truck configurations the PTO switch must be turned off to allow the transmission to shift into gear.

20. Altec LGSS-132-84 (81) Low-Side General Service Body With Step: 1

A. Steel Body B. Steel Structural Channel Crossmembers And Treadplate Floor C. 132'' Body Length D. 94'' Body Width E. 40'' Body Compartment Height F. 20'' Body Compartment Depth G. 24'' From Body Floor To Compartment Tops H. Finish Paint Entire Body Altec White I. Undercoat Applied Under The Body J. 5.5'' Drop-In Wooden Cargo Retaining Board At Rear Of Body K. 5.5'' Drop-In Wooden Retaining Board At Top Of Side Access Step L. Stainless Steel Rotary paddle Latches With Locks M. Gas Props On All Vertical Doors N. Chains On All Horizontal Doors

13 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

O. Standard Master Body Locking System P. Hotstick Shelf Extending Full Length Of Body On Streetside Q. Two (2) Hotstick Brackets On Streetside R. One Chock Holder On Each Side of Body With Retaining Lip In Fender Panel S. 1st Vertical (SS) - 34'' W - One (1) Outrigger Housing And Two (2) Adjustable

Shelves With Removable Dividers On 4 Inch Centers

T. 2nd Vertical (SS) - 24'' W - Two (2) Adjustable Shelves With Removable Dividers On 4 Inch Centers

U. 1st Horizontal (SS) - 50'' W - One (1) Fixed Shelf With Removable Dividers On 4 Inch Centers On Bottom of Compartment

V. Rear Vertical (SS) - 24'' W - Six (6) Locking Swivel Hooks On An Adjustable Rail (1-4-1)

W. 1st Vertical (CS) - 34'' W - One (1) Outrigger Housing And Two (2) Adjustable Shelves With Removable Dividers On 4 Inch Centers

X. 2nd Vertical (CS) - 24'' W - Gripstrut Access Steps With Two (2) Sloped Grab Handles, Vented Battery Storage

Y. 1st Horizontal (CS) - 50'' W - One (1) Adjustable Shelf With Removable Dividers On 4 Inch Centers And One (1) Fixed Shelf With Removable Dividers On 4 Inch Centers On Bottom Of Compartment

Z. Rear Vertical (CS) - 24'' W - Six (6) Locking Swivel Hooks On An Adjustable Rail (1-4-1)

AA. Body Floor Cut-Out For AT41M/P Aerial Device Near Front Of Body AB. Steel Tailshelf, 29'' L x 94'' W, With Rear Cross Storage And Drop Down Doors

21. ICC (Underride Protection) Bumper Installed At Rear 1

22. T-60 Style Pintle Hitch (10,000 LB MGTW with 2,000 LB MVL) 1

23. Set Of Eye Bolts for Trailer Safety Chain, installed one each side of towing device mount. 1

24. Rigid Step Mounted Beneath Side Access Steps (Installed To Extend Approx. 2'' Outward)

25. Platform Rest, Rigid with Rubber Tube 1

26. Boom Rest for a Telescopic Unit 1

27. Plastic Outrigger Pad, 18'' x 18'' x 1'', Black With Handle 2

28. Outrigger Pad Holder, 20'' L x 20'' W x 3'' H, Fits 19.5'' x 19.5'' x 2'' And Smaller Pads, Bolt-On, Bottom Washout Holes, 3/4'' Lip Retainer

29. Pendulum Retainers For Outrigger Pad Holders 2

30. Mud Flaps With Altec Logo (Pair) 1

14 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

31. Wheel Chocks, Rubber with Metal Hairpin Style Handle, 9.75'' L X 7.75'' W X 5.00'' H (Pair)

32. Slope Indicator Assembly For Machine With Outriggers 1

33. Driveaway Safety Kit 1

34. Vinyl manual pouch for storage of all operator and parts manuals 1

35. Lights and reflectors in accordance with FMVSS #108 lighting package. (Complete LED, including LED reverse lights)

36. Altec Standard Amber LED Strobe Light with Brush Guard Install on a post at the streetside front of the body.

37. Dual Tone Back-Up With Outrigger Motion Alarm 1

38. 6-Way Trailer Receptacle (Pin Type) Installed At Rear 1

39. Electric Trailer Brake Controller (Tekonsha Voyager #9030) 1

40. Ford Upfitter Switches (Supplied With Chassis) 1

41. Power Distribution Module Is A Compact Self-Contained Electronic System That Provides

A Standardized Interface With The Chassis Electrical System. (Includes Operator's Manual)

42. Install secondary stowage system. 1

43. Install Remote Start/Stop system in Final Assembly. 1

44. Install Outrigger Interlock System 1

45. PTO Indicator Light Installed In Cab 1

46. Powder Coat Unit Altec White 1

47. Altec Standard; Components mounted below frame rail shall be coated black by Altec.

i.e. step bumpers, steps, frame extension, pintle hook mount, dock bumper mounts, D-rings, receiver tubes, accessory mounts, light brackets, under-ride protection, etc.Components mounted to under side of body shall be coated black by Altec. i.e. Wheel chock holders, mud flap brackets, pad carriers, boxes, lighting brackets, steps, and ladders.

15 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

48. Apply Non-Skid Coating to all walking surfaces 1

49. English Safety And Instructional Decals 1

50. Vehicle Height Placard - Installed In Cab 1

51. Placard, HVI-22 Hydraulic Oil 1

52. Dielectric test unit according to ANSI requirements. 1

53. Stability test unit according to ANSI requirements. 1

54. Non-Focus Factory Build 1

55. Delivery Of Completed Unit 1

56. Inbound Freight 1

57. Installation - AT41P 1

58. Standard Altec Warranty: One (1) year parts warranty, one (1) year labor warranty, ninety

(90) days warranty for travel charges, limited lifetime structural warranty

AT41P Standard Retail Price

$129,028.00

Ohio STS Discount -($8,837.00)

AT41P Ohio STS Price

$120,191.00

Material Handling Aerial Device With ARM Jib Add $8,879.45

Material Handling Aerial Device With Side Mounted, hydraulically extendible Jib

Add $10,879.45

Auxiliary outriggers, 87” spread, fixed shoe (recommended for the 41’ material handler, required for the 48’ machine)

Add $4,260.27

Altec Model AT48P, in lieu of the 41’ machine (includes aux.

outriggers)

Add $18,009.89

Non Insulated Unit With 60” x 36” x 45” Platform, No Jib Add $7,047.95

Non Insulated Unit With 60” x 36” x 45” Platform, ARM Jib Add $15,927.40

24” x 48” x 42”, 2-Man Platform Add $786.30

16 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

Toe Space On Platform Add $1,231.51

84” CA Altec Fiberglass Body With Aluminum Treadplate Add $4,493.15

Custom Unit Color Add $3,561.64

Custom Body And Accessories Color Add $2,717.81

Rustproof Bottom Of Body Add $1,164.66

Gatorhyde Protective Cargo Coating, Cargo And Tailshelf Floor Areas

Add $2,931.51

17 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

18 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

50’ / 55’ / 60’ Telescopic Articulated Aerial Unit TA50 Aerial Device

1. Altec Model TA50 Articulating Telescopic Aerial Device with a fiberglass upper boom and fiberglass insulator in the articulating arm and a proportional joystick upper control and toggle switches. Built in accordance to ALTEC's standard specifications and to include the following

A. Ground to Bottom of Platform Height: 49.5 ft at 12.0 ft from centerline of rotation (15.1 m at 3.7 m)

B. Working Height: 54.5 ft (16.6 m) C. Maximum reach to edge of platform: 36.2 ft at 19.9 ft platform height (11 m at 6.1 m) D. Continuous Rotation

2. Automatic Upper Boom Stow Securing System with support cradle. 1

3. 288 Pedestal, 44 (1118 mm) inches, Behind Cab Mount 1

4. Single 1-Man Platform, 24" x 30" x 42" (610 x 762 x 1067 mm), End Mount, 180 Degree Rotation, No Jib

5. No Platform liner required 1

6. Tool Circuit At Boom Tip, Dual Hydraulic (TA End Mount) 1

7. Engine Start/Stop & Secondary Stowage System: 12 VDC powered motor and pump assembly for temporary operation of the unit in a situation wherein the primary hydraulic source fails. Electric motor is powered by the chassis battery. This feature allows the operator to completely stow the

19 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase booms, platform, and outriggers. Secondary Stowage & Start/Stop is activated with an air plunger at the plaform or momentary switch at the lower control station and outriggers.

8. 241 - Outrigger A-Frame with Flat-shoe - provides 149 inch (3785 mm) maximum spread outside to outside of shoe.

9. No Auxilary Outriggers 1

10. Electric Over Hydraulic Outrigger Control Valve 1

11. Altec Aerial Device Powder Painted White 1

12. Swivel Hook For Winch Load Line 1

13. Reservoir, 25 Gallon, Sloped, Mounted in Cargo Area 1

A. Internal return filter, 10 micron absolute, fiberglass media.

B. Ball valves in suction and return lines.

C. Suction strainer.

D. Filler/breather cap with dipstick.

14. TA Series Subbase 1

15. Temperature Sight Gauge . 1

16. HVI-22 Hydraulic Oil (Standard). 30

17. Standard Pump For PTO 1

18. Hot shift PTO for automatic transmission 1

19. Standard PTO/Transmission Functionality for Automatic Transmissions - If chassis is in gear, and PTO switch is activated, PTO will not engage. Chassis will remain in gear.

If chassis is already in neutral with PTO engaged and operator tries to shift into gear, PTO will disengage and transmission will shift into gear.

20. 160 inch Universal Aerial Body, suitable for installing on any 4x2 chassis with an appropriate CA dimension of 108 inches, built in accordance with the following specifications:

20 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

A. Basic body fabricated from A40 grade 100% zinc alloy steel.

B. All doors are full, double paneled, self-sealed with built-in drainage for maximum weather-tightness. Stainless steel hinge rods extend full length of door.

C. All doors are to contain stainless steel flush type, single point, two-stage rotary paddle latches with recessed handles, including keyed locks and strikers. door latches are bolted to the outer door panel.

D. Heavy-gauge welded steel frame construction with structural channel crossmembers and tread plate floor.

E. All edges are either rolled or folded for strength and safety.

F. Integrated door header drip rail at top for maximum weather protection.

G. Fender panels are either roll formed or have neoprene fenderettes mechanically fastened.

H. Steel treated for improved primer bond and rust resistance.

I. Automotive underseal applied to entire underside of body.

J. White primer applied to complete interior and exterior of body.

K. Automotive type non-porous door seals mechanically fastened to the door facing.

L. 160 inch overall body length.

M. 94 inch overall body width.

N. 46 inch overall body height.

O. 18 inch body compartment depth.

P. Body finish paint color - Altec White.

Q. Finish paint body at body manufacturer.

R. 2 inch x 6 inch drop-in wood cargo retaining board at rear of body.

S. 2 inch x 6 inch drop-in wood cargo retaining board at side access step.

T. Gas shock type rigid door holders for vertical doors.

U. Standard master body locking system.

V. One (1) wheel chock holder installed in fender panel on each side of body.

W. Hotstick shelf extending the full length of body on streetside.

X. Two (2) hotstick brackets installed on streetside.

Y. Standard size side-hinged hotstick door installed on streetside.

Z. 1st vertical streetside (LH) - Six (6) locking swivel hooks on adjustable rails. 2-2-2 configuration.

AA. 2nd vertical streetside (LH) - Six (6) locking swivel hooks on adjustable rails. 2-2-2

AB. 3rd vertical streetside (LH) - Six (6) locking swivel hooks on adjustable rails. 2-2-2

AC. 1st horizontal streetside (LH) - One (1) adjustable shelf with removable dividers on 4 inch centers.

AD. Rear vertical streetside (LH) - Two (2) adjustable shelves with removable dividers on 4 inch

AE. 1st vertical curbside (RH) - Two (2) adjustable shelves with removable dividers on 4 inch

AF. 2nd vertical curbside (RH) - Gripstrut access steps with two (2) sloped grab handles.

AG. 3rd vertical curbside (RH) - Six (6) locking swivel hooks on adjustable rails. 2-2-2

21 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

AH. 1st horizontal curbside (RH) - Two (2) adjustable shelves with removable dividers on 4 inch

AI. Rear vertical curbside (RH) - Six (6) locking swivel hooks on adjustable rails. 2-2-2

AJ. Curbside compartment top access step installed in the cargo area behind side access step.

AK. 29 inch long x 94 inch wide steel tailshelf, with 3 inch high retainer rail around sides and rear, two (2) U-shaped grab handles, installed at rear of body.

21. ICC (Underride Protection) Bumper Installed At Rear 1

22. T-125 Style Pintle Hitch (30,000 LB MGTW with 6,000 LB MVL) 1

23. Set Of Eye Bolts for Trailer Safety Chain, installed one each side of towing device mount. 1

24. Cable Step Installed At Rear, Double Step with Rigid Top Step 2

25. Rubber Belted Step Mounted Beneath Side Access Steps (Installed To Extend Approx. 2'' Outward) 1

26. Platform Access Step From Body Floor 1

27. Boom Rest for a Telescopic Unit 1

28. Plastic Outrigger Pad, 24'' x 24'' x 1'', Black With Handle 4

29. Outrigger Pad Holder, 25'' L x 25'' W x 3'' H, Fits 24.5'' x 24.5'' x 2'' And Smaller Pads, Bolt-On, Bottom Washout Holes, 3/4'' Lip Retainer

30. Mud Flaps With Altec Logo (Pair) 1

31. Wheel Chocks, Rubber with Metal Hairpin Style Handle, 9.75'' L X 7.75'' W X 5.00'' H (Pair) 1

32. U-Shaped Grab Handle 2

33. Slope Indicator Assembly For Machine With Outriggers 1

34. Triangular Reflector Kit, Installed 1

35. 5 LB Fire Extinguisher With Light Duty Bracket, Installed Per DEPS 042 (In Cab or Inside

36. Vinyl manual pouch for storage of all operator and parts manuals 1

22 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

37. Lights and reflectors in accordance with FMVSS #108 lighting package. (Complete LED, including

38. Altec Standard Amber LED Strobe Light with Brush Guard - Install on streetside boomrest 1

39. Altec Standard Multi-Point Grounding System 3

40. 7-Way Trailer Receptacle (Pin Type) Installed At Rear 1

41. Electric Trailer Brake Controller (Tekonsha Voyager #9030) 1

42. Power Distribution Module Is A Compact Self-Contained Electronic System That Provides A

Standardized Interface With The Chassis Electrical System. (Includes Operator's Manual)

43. Altec Modular Panel System (AMPS) - Includes Mounting Panel and Accessory Switches 1

44. Non-Focus Factory Build 1

45. Delivery Of Completed Unit 1

46. Inbound Freight 1

47. Finish Paint Body Accessories Above Body Floor Altec White 1

48. Altec Standard; Components mounted below frame rail shall be coated black by Altec. i.e. step tubes, accessory mounts, light brackets, under-ride protection, etc.Components mounted to under side of body shall be coated black by Altec. i.e. Wheel chock holders, mud flap brackets, pad carriers, boxes, lighting brackets, steps, and ladders.

49. Apply Non-Skid Coating to all walking surfaces 1

50. English Safety And Instructional Decals 1

51. Vehicle Height Placard - Installed In Cab 1

52. Dielectric test unit according to ANSI requirements. 1

53. Stability test unit according to ANSI requirements. 1

54. Placard, HVI-22 Hydraulic Oil 1

23 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

55. TA50 FA Installation 1

56. Standard Altec Warranty: One (1) year parts warranty, one (1) year labor warranty, ninety (90)

TA50 Standard Retail Price

$148,145.00

Ohio STS Discount -($9,619.00)

TA50 Ohio STS Price

$138,526.00

50’ Auxiliary Outriggers, Bolt On Style Add $4,435.06

55’ Telescoping Articulating Unit, Includes Aux. Outriggers Add $11,407.79

60’ Telescoping Articulating Unit, Includes Aux. Outriggers Add $16,505.19

24” x 30” x 42” Platform With ARM Jib Add $7,142.86

24” x 48” x 42” Platform With No Jib Add $3,928.57

24” x 48” x 42” Platform With ARM Jib Add $9,129.87

24” x 30” x 42” Platform With Side Mounted Jib, 90 degree Add $5,251.95

24” x 48” x 42” Platform With Side Mounted Jib, 90 degree Add $9,129.87

24” platform elevator Add $5,172.73

Altec Fiberglass Body With Aluminum Treadplate Add $12,718.18

Custom Color Above Rotation And Pedestal Add $3,376.62

Custom Color Body And Accessories Add $2,401.30

Rustproof Bottom Of Body Add $1,104.16

Gatorhyde Protection Paint, Cargo And Tailshelf Area Add $3,102.60

24 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

25 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

50’ / 55’ / 60’ Articulated Aerial Unit

AA50 Aerial Device

1. Altec Model AA50 Articulating Non-Overcenter Aerial Device with a fiberglass upper boom and fiberglass insulator in the lower boom and a proportional joystick upper control and toggle switches. Built in accordance to ALTEC’s standard specifications and to include the following

A. Ground to Bottom of Platform Height: 50.1 ft at 9.0 ft from centerline of rotation (15.3 m at 2.7 m)

B. Working Height: 55.1 ft (16.8 m) C. Maximum reach to edge of platform: 34.6 ft at 28.5 ft platform height (10.5 m at 8.7 m) D. Rotation: Continuous

2. 375 – Automatic stow system 1

3. 219 – Single two-man end mount 24x48x42 1

6. 315 Engine start/stop with Secondary Stowage System, 12 VDC electric powered. Includes auxiliary pump and electric motor, powered by the chassis battery. Control is captive air operated from the platform and toggle switch operated from the lower controls. This option allows the operator to completely stow the booms and platform in a situation wherein the engine, PTO or pump fails.

7. 450 – Outrigger A-Frame with fold-up shoe – 153 inch max spread 1

8. 241 – Outrigger A-Frame with Flat-shoe – provides 149 inch (3785 mm) maximum spread outside to outside of shoe.

9. 319 – Category C 46 kV and below 1

10. Powder coat unit Altec White. 1

26 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

11. Unit Installation Components. 1

12. Reservoir, 30 Gallon, Triangular, Mounted in Cargo Area 1

A. Internal return filter, 10 micron absolute, fiberglass media B. Ball valves in suction and return lines.

C. Magnetic suction strainer.

13. AA/AN 50/55/50E/55E/60/60E AN46-OC/50-OC/55-OC/46E-OC/50E-OC/55E-OC Subbase 1

14. Temperature Sight Gauge . 1

15. HVI-22 Hydraulic Oil (Standard). 35

16. Standard Pump For PTO 1

17. Hot shift PTO for automatic transmission 1

18. Standard PTO/Transmission Functionality for Automatic Transmissions - If chassis is in gear, and PTO switch is activated, PTO will not engage. Chassis will remain in gear.

19. 170 inch Large Universal Aerial Body with outrigger housings, suitable for installing on any 4x2 chassis with an appropriate CA dimension of 120 inches, built in accordance with the following specifications:

latches with recessed handles, including keyed locks and strikers. Door latches are bolted

G. Fender panels are either roll formed or have neoprene fenderettes mechanically fastened.

H. Steel treated for improved primer bond and rust resistance.

I. Automotive underseal applied to entire underside of body.

J. Automotive type non-porous door seals mechanically fastened to the door facing.

K. 170 inch overall body length.

27 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

L. 94 inch overall body width.

M. 46 inch overall body height.

N. 18 inch body compartment depth.

O. Body finish paint color – Altec White.

P. Finish paint body at body manufacturer.

Q. 2 inch x 6 inch drop-in wood cargo retaining board at rear of body.

R. 2 inch x 6 inch drop-in wood cargo retaining board at top of side access step.

S. Gas shock type rigid door holders for vertical doors.

T. Standard master body locking system.

U. One (1) wheel chock holder installed in fender panel on each side of body.

V. Hotstick shelf extending from rear of first vertical to rear of body on streetside.

W. Two (2) hotstick brackets installed on street side.

X. Large side hinged hotstick door for multiple shelves on streetside.

Y. 1st vertical street side (LH) – Three (3) adjustable shelves with removable dividers on 4 inch

Z. 2nd vertical street side (LH) – Six (6) locking swivel hooks on adjustable rails. 1-4-1

AA. 3rd vertical street side (LH) – Six (6) locking swivel hooks on adjustable rails. 1-4-1

AB. 1st horizontal street side(LH) – One (1) fixed shelf extending through rear vertical.

AC. Rear vertical street side (LH) – Outrigger housing.

AD. 1st vertical curb side (RH) – Three (3) adjustable shelves with removable dividers on 4 inch

AE. 2nd vertical curb side (RH) – Six (6) locking swivel hooks on adjustable rails. 1-4-1

AF. 3rd vertical curb side (RH) – Gripstrut access steps with two (2) sloped grab handles.

AG. 1st horizontal curb side (RH) – Two (2) fixed shelves with removable dividers on 8 inch

AH. Rear Vertical curb side (RH) – Outrigger housing.

AI. Curbside compartment top access step installed in the cargo area 7 inches behind side access step.

AJ. 24 inch long x 94 inch wide steel tailshelf with 3 inch high retainer rail around sides and rear, installed at rear of body.

20. ICC (Underride Protection) Bumper Installed At Rear 1

21. T-125 Style Pintle Hitch (30,000 LB MGTW with 6,000 LB MVL) 1

22. Set Of Eye Bolts for Trailer Safety Chain, installed one each side of towing device mount. 1

23. Cable Step Installed At Rear, Double Step with Rigid Top Step 2

24. Platform Access Step From Body Floor 1

25. Single Platform Access, One Step Mounted to Turntable 1

26. Platform Rest, Rigid with Rubber Tube 1

28 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

27. Lower Boom Rest Weldment 1

28. Mounting Brackets for Lights, Located on Lower Boom Rest 1

29. Plastic Outrigger Pad, 24’’ x 24’’ x 1’’, Black With Handle 4

30. Outrigger Pad Holder, 25’’ L x 25’’ W x 3’’ H, Fits 24.5’’ x 24.5’’ x 2’’ And Smaller Pads, Bolt-On, Bottom Washout Holes, 3/4’’ Lip Retainer

31. Mud Flaps With Altec Logo (Pair) 1

32. Wheel Chocks, Rubber with Metal Hairpin Style Handle, 9.75’’ L X 7.75’’ W X 5.00’’ H (Pair) 1

33. U-Shaped Grab Handle 2

34. Slope Indicator Assembly For Machine With Outriggers 1

35. Triangular Reflector Kit, Installed 1

36. 5 LB Fire Extinguisher With Light Duty Bracket, Installed Per DEPS 042 (In Cab or Inside

37. Vinyl manual pouch for storage of all operator and parts manuals 1

38. Lights and reflectors in accordance with FMVSS #108 lighting package. (Complete LED, including

39. Altec Standard Amber LED Strobe Light with Brush Guard – Install on streetside of boomrest 1

40. Dual Tone Back-Up With Outrigger Motion Alarm 1

41. Altec Standard Multi-Point Grounding System 3

42. 7-Way Trailer Receptacle (Pin Type) Installed At Rear 1

43. Electric Trailer Brake Controller (Tekonsha Voyager #9030) 1

44. Power Distribution Module Is A Compact Self-Contained Electronic System That Provides A

Standardized Interface With The Chassis Electrical System. (Includes Operator’s Manual)

45. Altec Modular Panel System (AMPS) – Includes Mounting Panel and Accessory Switches 1

46. Non-Focus Factory Build 1

47. Delivery Of Completed Unit 1

29 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

48. Inbound Freight 1

49. Powder Coat Unit Altec White 1

50. Finish Paint Body Accessories Above Body Floor Altec White 1

51. Altec Standard; Components mounted below frame rail shall be coated black by Altec. i.e. step tubes, accessory mounts, light brackets, under-ride protection, etc.Components mounted to under side of body shall be coated black by Altec. i.e. Wheel chock holders, mud flap brackets, pad carriers, boxes, lighting brackets, steps, and ladders.

52. Apply Non-Skid Coating to all walking surfaces 1

53. English Safety And Instructional Decals 1

54. Vehicle Height Placard – Installed In Cab 1

55. Dielectric test unit according to ANSI requirements. 1

56. Stability test unit according to ANSI requirements. 1

57. Placard, HVI-22 Hydraulic Oil 1

58. AA50 FA Installation

59. Standard Altec Warranty: One (1) year parts warranty, one (1) year labor warranty, ninety (90)

AA50 Standard Retail Price

$147,513.00

Ohio STS Discount -($9,578.00)

AA50 Ohio STS Price

$137,934.00

30 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

55’ Unit in lieu of 50’ Unit Add $1,745.45

60’ Unit in lieu of 50’ Unit Add $8,118.18

Non-compensated boom system in lieu of compensated boom system

Deduct ($2,627.27)

Extended reach lower boom unit in lieu of standard reach lower boom unit (requires the use of X-Frame outriggers, see next option for additional pricing)

Add $3,140.26

X-Frame primary outriggers, in lieu of A-Frame type Add $14,415.58

Over-Center unit in lieu of non over-center (only available on the non-compensated boom systems)

Add $2,253.25

Single Two-Man, End Mount, 180 Degree Add $2,590.91

Single Two-Man, 90 Degree, Side Mounted Hydraulic Jib/Winch, Forward Mounted ISO-Grip Controller

Add $8,637.66

24” Vertical Lift On Platform Add $5,355.84

Altec Fiberglass Body With Aluminum Treadplate Add $13,172.73

Custom Color Above Rotation And Pedestal Add $3,376.62

Custom Color Body And Accessories Add $3,088.31

31 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

50’ / 55’ / 60’ Articulated Over-Center Material Handler Aerial Unit

AM50 Aerial Device

1. 203 Altec Model AM50 articulating overcenter aerial device with an insulated lower boom, insulated upper boom and an insulated ISO-Grip (U.S. Patent No. 7,416,053) System at the boom tip, for installation over rear axle, built in accordance to Altec standard specifications and to include the following features:

A. Ground to Bottom of Platform Height: 50.3 feet at 4.0 feet from centerline of rotation

(15.3 m at 1.2 m)

B. Working Height: 55.3 feet (16.8 m) C. Maximum Reach to Edge of Platform with Upper Boom Overcenter: 42.7 feet (13.0 m) D. Maximum Reach to Edge of Platform with Upper Boom Non-overcenter and Lower Boom at 100 degrees: 31.4 feet at 27.3 foot platform height (9.6 m at 8.3 m)

2. 375 - Automatic Upper Boom Latch 1

3. 217 - Single, Two-Man Side-Mounted Platform - 24 X 48 X 42 Inches (610 X 1219 X 1067 Mm);

Platform Is Rated Up To 800 Pounds (363 Kg). Platform Rotates 90 Degrees To End Of Boom With Altec Patented Rotator. Includes Two Sets Of Quick Disconnects And Controls For Hydraulic Tools.

6. 239 - Platform Capacity Rating Of 400 Lbs. Per Operator, 400 Lbs. For Single Man Platform, 800

Lbs. For Two Man Platform

A. Maximum Platform Capacity On AM55 With Dual Controls Is 350 Lbs. Per Platform B. All Capacities Are Based On Bare Platforms, Liner Weight Is Not Included

32 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

7. 338 - Pilot Pressure - System Operates At 350 To 3,000 Psi (24 To 207 Bar), And 17 Gpm (64.4 Lpm). System Is Closed Center, Pressure Compensating.

8. Twist style single handle controller. The controller is positioned so that when you are standing in the platform with the platform in the stowed position facing the controller the handle points towards the elbow of the unit and the head of the controller points toward rear of the truck.

Unit rotation is driven by a twist action of the control handle. This style of controller is only available with a pilot pressure system.

9. 219 - Hydraulic Extend Jib - Material Handling, Hydraulically Articulated Jib, -30 Degrees To +90

Degrees Tilt Angle (Relative To The Upper Boom). Jib Can Be Hydraulically Extended To 54.4 Inches (1382 Mm) From Mounting Shaft To Load Line. The Jib Is Hydraulically Extended And Retracted In Two 18 Inch (457 Mm) Increments For A Total Of 36 Inches (914 Mm) Under Full Load.

A. Capacities Up To 2000 Pounds (907 Kg) Based On Boom Position B. Load Chart Based On Platform Configuration C. Hydraulically Articulated Jib With -30 Degrees To 90 Degrees Tilt Angle Relative To The

Upper Boom. Jib Is One Piece, 4 Inches Square X 63 Inches Long (102 X 1600 Mm)

D. Hydraulically Extendible Jib Telescopes In And Out 18 Inches (457 Mm). Jib May Be Manually Re-Pinned Under Load And Telescoped An Additional 18 Inches For A Total Movement Of 36 Inches (914 Mm) Under Load

E. Hydraulically Powered Winch That Is Rated To 2,000 Pounds (907 Kg) Full Drum, Mounted On End Of Upper Boom And Includes 80 Feet (24 M) Of 1/2 Inch (13 Mm) Double-Braided Synthetic Rope

F. Auxiliary Winch Line Control Valve At Turntable

10. 236 - Maximum Jib Rating - Applied To All AM Series Machines, This Rating Provides The Maximum Jib Capacity At All Lower Boom Positions.

11. 393 - 12 VDC Electrical System Voltage 1

12. Engine Start/Stop with Secondary Stowage System, 12 VDC electric powered. Includes pump and motor, operates from chassis battery. Control is captive air operated from the platform and momentary switch operated from the lower controls. This option allows the operator to start and stop the operation of the units as well as completely stow the booms and platform in a situation wherein the primary hydraulic source fails.

13. 470 - Primary Outrigger, X-Frame With Fold-Up Shoe - Provides 174 (4429 Mm) Maximum Spread

And Weighs 1,500 Pounds (680 Kg)

14. Outrigger, Auxiliary, A-Frame With Flat-Shoe - Provides 149 (3785 Mm) Maximum Spread And

Weighs 1,050 Pounds (476 Kg)

15. 319 - Category C, 46 kV And below 1

16. Powder coat unit Altec White. 1

33 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

17. AM50/50E/55/55E/60/60E Series Unit Installation Components 1

18. Swivel Hook For Winch Load Line 1

19. Standard 1" Space between Subbase and frame for hose routing and ease of maintenance. 1

20. Reservoir, 30 Gallon, Triangular, Mounted in Cargo Area 1

21. AM50/55/60/50E/55E/60E Subbase 1

22. Temperature Sight Gauge . 1

23. HVI-22 Hydraulic Oil (Standard). 35

24. Standard Pump For PTO 1

25. Hot shift PTO for automatic transmission 1

26. Standard PTO/Transmission Functionality for Automatic Transmissions - If chassis is in gear, and PTO switch is activated, PTO will not engage. Chassis will remain in gear.

27. 170 inch Large Universal Aerial Body with outrigger housings, suitable for installing on any 4x2 chassis with an appropriate CA dimension of 120 inches, built in accordance with the following specifications:

latches with recessed handles, including keyed locks and strikers. door latches are bolted

34 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

G. Fender panels are either roll formed or have neoprene fenderettes mechanically fastened.

H. Steel treated for improved primer bond and rust resistance.

I. Automotive underseal applied to entire underside of body.

J. White primer applied to complete interior and exterior of body.

K. Automotive type non-porous door seals mechanically fastened to the door facing.

L. 170 inch overall body length.

M. 94 inch overall body width.

N. 46 inch overall body height.

O. 18 inch body compartment depth.

P. Body finish paint color - Altec White.

Q. Finish paint body at body manufacturer.

R. 2 inch x 6 inch drop-in wood cargo retaining board at rear of body.

S. 2 inch x 6 inch drop-in wood cargo retaining board at top of side access step.

T. Gas shock type rigid door holders for vertical doors.

U. Standard master body locking system.

V. One (1) wheel chock holder installed in fender panel on each side of body.

W. Hotstick shelf extending from rear of first vertical to rear of body on streetside.

X. Two (2) hotstick brackets installed on street side.

Y. Large side hinged hotstick door for multiple shelves on streetside.

Z. 1st vertical street side (LH) - Three (3) adjustable shelves with removable dividers on 4 inch centers.

AA. 2nd vertical street side (LH) - Six (6) locking swivel hooks on adjustable rails. 1-4-1

AB. 3rd vertical street side (LH) - Six (6) locking swivel hooks on adjustable rails. 1-4-1

AC. 1st horizontal street side(LH) - One (1) fixed shelf extending through rear vertical.

AD. Rear vertical street side (LH) - Outrigger housing.

AE. 1st vertical curb side (RH) - Three (3) adjustable shelves with removable dividers on 4 inch

AF. 2nd vertical curb side (RH) - Six (6) locking swivel hooks on adjustable rails. 1-4-1

AG. 3rd vertical curb side (RH) - Gripstrut access steps with two (2) sloped grab handles.

AH. 1st horizontal curb side (RH) - Two (2) fixed shelves with removable dividers on 8 inch

AI. Rear Vertical curb side (RH) - Five (5) locking swivel hooks on adjustable rails. 1-3-1

AJ. Rear Vertical curb side (RH) - Outrigger housing.

AK. Curbside compartment top access step installed in the cargo area 7 inches behind side access step.

AL. 24 inch long x 94 inch wide steel tailshelf with 3 inch high retainer rail around sides and

35 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase rear, installed at rear of body.

28. ICC (Underride Protection) Bumper Installed At Rear 1

29. T-125 Style Pintle Hitch (30,000 LB MGTW with 6,000 LB MVL) 1

30. Set Of Eye Bolts for Trailer Safety Chain, installed one each side of towing device mount. 1

31. Cable Step Installed At Rear, Double Step with Rigid Top Step 2

32. Platform Access Step From Body Floor 1

33. Platform Rest, Rigid with Rubber Tube 1

34. Lower Boom Rest Weldment 1

35. Mounting Brackets for Lights, Located on Lower Boom Rest 1

36. Plastic Outrigger Pad, 24'' x 24'' x 1'', Black With Handle 4

37. Outrigger Pad Holder, 25'' L x 25'' W x 3'' H, Fits 24.5'' x 24.5'' x 2'' And Smaller Pads, Bolt-On, Bottom Washout Holes, 3/4'' Lip Retainer

38. Pendulum Retainers For Outrigger Pad Holders 4

39. Mud Flaps With Altec Logo (Pair) 1

40. Wheel Chocks, Rubber with Metal Hairpin Style Handle, 9.75'' L X 7.75'' W X 5.00'' H (Pair) 1

41. U-Shaped Grab Handle 2

42. Slope Indicator Assembly For Machine With Outriggers 1

43. Triangular Reflector Kit, Installed 1

44. 5 LB Fire Extinguisher With Light Duty Bracket, Installed Per DEPS 042 (In Cab or Inside

45. Vinyl manual pouch for storage of all operator and parts manuals 1

36 Options And Chassis Selections To Be Reviewed By Altec Prior To Purchase

46. Lights and reflectors in accordance with FMVSS #108 lighting package. (Complete LED, including

47. Altec Standard Amber LED Strobe Light with Brush Guard - Install on streetside of boomrest 1

48. Dual Tone Back-Up With Outrigger Motion Alarm 1

49. Altec Standard Multi-Point Grounding System 3

50. 7-Way Trailer Receptacle (Pin Type) Installed At Rear 1

51. Electric Trailer Brake Controller (Tekonsha Voyager #9030) 1

52. Power Distribution Module Is A Compact Self-Contained Electronic System That Provides A

53. Altec Modular Panel System (AMPS) - Includes Mounting Panel and Accessory Switches 1

54. Non-Focus Factory Build 1

55. Delivery Of Completed Unit 1

56. Inbound Freight 1

57. Powder Coat Unit Altec White 1

58. Finish Paint Body Accessories Above Body Floor Altec White 1

59. Altec Standard; Components mounted below frame rail shall be coated black by Altec. i.e. step tubes, accessory mounts, light brackets, under-ride protection, etc.