2626041_PKGRQMT_REPORT_EDA.PDF

TECHNICAL DATA PACKAGE - ENGINEERING NOTES (ENs)

OF 4 PAGES

NATIONAL STOCK NUMBER PART NUMBER

2840-01-259-4369JF 7089M92G03

X WHEN CHECKED BELOW OR LISTED IN THESE NOTES, DEFINITIONS APPLICABLE TO

THIS PRODUCT ARE OR HAVE:

(A) ENGINEERING CRITICAL IN APPLICATION: An item which requires special manufacturing process, controls, and testing of material or end items.

Because of its use or application, failure to maintain the highest reliability of such an item could be catastrophic resulting in loss of life or serious injury, loss of a weapon system or extensive secondary damage, with direct impact on the capability to respond to a national emergency or to achieve wartime sustainability.

(B) COMPLEX: Items having quality characteristics not wholly visible (hidden characteristics), in the end product for which contractual conformance must be established progressively through precise measure-ments, tests or controls applied during purchasing, manufacturing, performance, assembly and functional operation either as an individual item or in conjunction with other items [FAR SUBPART 46.203(b)].

(c) COMMERCIAL: Described in commercial catalogs, drawings or industrial standards [FAR SUBPART 46.203(a),(1)].

(D) CRITICAL CHARACTERISTICS: Characteristics which, when defective, are likely to result in hazardous or unsafe conditions for individuals using, maintaining or depending upon the product; or, are likely to prevent per-formance of the tactical function of a major end item such as an aircraft, missile, space vehicle, engine or a major part thereof. (Derived from

MIL-STD-1916).

(E) MAJOR CHARACTERISTICS: Characteristics (other than critical or minor), which, when defective, are likely to result in failure or to reduce the usability of the product or a major end item for its intended purpose.

(Derived from MIL-STD-1916).

(F) MINOR CHARACTERISTICS: All characteristics not designated as critical or major but for which full conformity is required.

THIS PRODUCT HAS BEEN DETERMINED TO BE OR CONTAINS (AS CHECKED BELOW):

X Engineering critical in application.

Critical characteristics

Major characteristics

X Minor characteristics, all excepting critical and major.

Complex

Available as a commercial product

AFLC FORM 2559 (COMPUTER GENERATED) PREVIOUS EDITION WILL BE USED

_X_ When materials, processes or components are to be obtained from directed sources as indicated herein or in the specifications, alternate sources may only be utilize upon prior approval by the contracting officer of this procuring activity as a deviation.

_X_ Bidders are requested to notify the contracting officer in writing as soon as is practicable of any drawing, specification, standard or other required technical data which is of more current date/revision than that shown on the Engineering Data List.

_X_ Contractor is authorized to the extent specified herein to use standards, specifications, and other required technical data which are of a more current date/revision than those shown on the Engineering Data List. Proposed changes to revision-in-use other than those allowed by this paragraph must be submitted in writing to the contracting officer for approval by the cognizant engineering authority.

a. VENDOR DRAWINGS, VENDOR MASTER DRAWINGS (MYLARS), AIRFOIL DATA, CONTOUR DATA, AND PERFORMANCE DATA: (e.g. 1234m56, 658972, AD658972, IC658972, IF-658972) Revisions specified on the ENGINEERING DATA LIST are the revisions to be used for manufacturing. Requests to use later revisions must be submitted for approval in writing to the contracting officer, along with the newer revision document, for approval by the cognizant engineering authority.

b. VENDOR SPECIFICATIONS, VENDOR STANDARDS, INSPECTION PHOTOGRAPHS: (e.g. P1TF3, PWA360, EPS14500) The revisions specified on the Engineering Data List form a baseline minimum revision status, and are the most recent revisions the government can provide. No revision before that shown in the Engineering Data List will be used. Revisions later than those specified in the Engineering Data List may be used provided:

1. The contractor notifies the contracting officer in writing of the revision to be used, and

2. The new revision does not and will not affect form, fit, or function of the part, process, or material being manufactured and/or supplied, and

3. Use of the new revision will not increase the cost to the government of compensation for the product being supplied, and

4. The Engineering Notes do not contain a clause specifically excluding the allowances of this paragraph.

c. INDUSTRY SPECIFICATIONS/STANDARDS, MILITARY

SPECIFICATIONS/STANDARDS, QUALIFIED PRODUCT LIST (QPL):

(e.g. AMS 5613, ANSI Y14.5, MIL-STD-130, QPL 25135) The revision to be used will be the revision in effect on the

TECHNICAL DATA PACKAGE - ENGINEERING NOTES (Ens) dates of opening of solicitation. Later revisions of these documents are approved for use provided:

1. The new revision does not and will not affect form, fit, or function of the part, processes, or material being manufactured and/or supplied and

2. Use of the new revision will not increase the cost to the government of compensation for the product being supplied.

_X_ Lower tier specifications listed in or referenced by first tier specifi-cations may not be shown on the data lists or engineering notes accom-panying this contract but are nonetheless required by this contract for compliance. Exceptions would occur only when such lower tier requirements have been specifically waived or substitute specifications/requirements are designated herein.

_X_ Reports, process sheets, inspection methods sheets and all other documents required by specifications imposed by this contract for contractor compli-ance which were previously required to be submitted to a prime design con-tractor shall be held at that facility for review by government personnel.

_X_ When prime design source specifications require or provide for participa-tion by that prime source quality, manufacturing, laboratory or engineering support services, these requirements or provisions do not apply when the contract was issued by this procuring activity. For these services or direction pertaining thereto, contact the cognizant government contract administration office or this procuring activity for assistance.

_X_ The contractor is responsible for assuring that all dimensions, conditions, tests and test results identified in these engineering notes, applicable drawings, specifications and contract quality requirements are met by themselves and their suppliers. This requirement applies to all character-istics whether those characteristics have been specifically designed as being critical, major or are those minor characteristics not specifically designated as such.

_X_ Prior to beginning of manufacture, the contractor will notify the engineering office of this procuring activity of all manufacturing processes and processing procedures intended for use in production of this product. Once these processes are established, no changes shall be made without prior approval of the engineering office of this procuring activity.

___ Serialization of each part/assembly (contract end item)is required.

NATIONAL STOCK NUMBER PART NUMBER DATE

2840-01-259-4369JF 7089M92G03 8 AUG 2018

I. GENERAL NOTES

A. PARTS SHALL BE IDENTIFIED PER MIL-STD-130 USING THE METHOD(S) SPECIFIED BY P23TF3 AND

THE APPLICABLE DRAWING(S).

B. USE GE PHOTO 8311253 IN LIEU OF 102A161.

C. USE AMS 4233 IN LIEU OF AMS 4188.

D. USE AMS 2175 IN LIEU OF MIL-C-6021.

E. USE AS 8879 IN LIEU OF MIL-S-8879.

F. USE AIA/NAS NASM33537 IN LIEU OF MS33537.

II. CONTROLLED PROCESSES

A. MATERIAL

B. WELDING

C. RADIOGRAPHIC INSPECTION

D. FLUORESCENT PENETRANT INSPECTION

E. IMPREGNATION OF CASTING

AFLC FORM 2559 (COMPUTER GENERATED) PREVIOUS EDITION WILL USED

PACKAGING REQUIREMENTS

PURCHASE INSTRUMENT NUMBER: FD20301900220-00 VERSION: 1

MIL-STD 129 REVISION: R MIL-STD 2073-1 REVISION: E

THE FOLLOWING STATEMENT IS IN COMPLIANCE WITH THE UNITED NATIONS-IMPLEMENTED RESTRICTIONS ON WOOD PACKAGING MATERIAL (WPM). THIS REQUIREMENT IS SPECIFICALLY CONCERNED WITH INVASIVE SPECIES SUCH AS THE PINEWOOD NEMATODE. WPM IS DEFINED AS WOOD PALLETS, SKIDS, LOAD BOARDS, PALLET COLLARS, WOODEN BOXES, REELS, DUNNAGE, CRATES, FRAMES, AND CLEATS. THE STATEMENT BELOW CITES THE REQUIREMENTS IN DETAIL AND COVERS LUMBER FOR BUILDING CONTAINERS AND PALLETS USED FOR DELIVERIES RESULTING IN SHIPMENTS WORLDWIDE (DIRECT, OR THROUGH AIR LOGISTICS CENTERS (ALC), CONTAINER CONSOLIDATION POINTS (CCP), OR OTHER BASES). WOODEN LUMBER, WOODEN

PALLET AND PACKAGING/CONTAINER STATEMENT:

ALL WOODEN LUMBER, WOODEN PALLET'S, AND WOODEN CONTAINERS PRODUCED ENTIRELY OR IN PART OF WOOD PACKING MATERIAL (WPM) SHALL BE CONSTRUCTED FROM DEBARKED WOOD IN ADDITION TO THE APPLICATION OF HEAT-TREATED (HT) MATERIAL (HT TO 56 DEGREES CENTIGRADE OR 133 DEGREES FAHRENHEIT FOR 30 MINUTES). CERTIFICATION/MARKING IS REQUIRED BY AN ACCREDITED AGENCY RECOGNIZED BY THE AMERICAN LUMBER STANDARDS COMMITTEE (ALSC). FOR REFERENCE DOCUMENTATION, SEE LATEST REVISION OF "INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES" (ISPM)NO.15), "REGULATION OF WOOD PACKAGING MATERIAL IN INTERNATIONAL TRADE."

PACRN: PACKAGING REQUIREMENT: PRESERVATION LEVEL: PACKAGING LEVEL: SPI: SPI REV: SPI DATE:

AAA MIL Long Line Packaging MIL B

ITEM(S):

2840012594369JF

CODED DATA:

QUP ICQ

PRES

METH CD

PRES

MTL

WRAP

MTL

CUSH

DUNN CT

UNIT

CONT

INT

CONT UCL

SPEC

MKG

UNIT PACK

WEIGHT

LENGTH

WIDTH

DEPTH

CUBE OPI

1 000 AE 1 00 JA NA A ED 00 B 00 13.80 29.5 14.5 14.5 3.589 O

ADDITIONAL PACKAGING AND CONTAINER MARKING REQUIREMENTS:

SUPPLEMENTAL PACKAGING INSTRUCTION TEXT:

VENDOR PACKAGING INSTRUCTIONS:

Military Packaging and Marking Items shall be packaged in accordance with MIL-STD-2073-1, Standard Practice for Military Packaging. Shipping and storage markings shall be in accordance with MIL-STD-129, Standard Practice for Military Marking.

Shipping Container Marking Shipping containers shall be marked meeting the following criteria: (a) MIL-STD-129, Standard Practice for Military Marking. (b) Bar code format shall conform to bar code symbology Format 3 of 9, Code 39 as specified in MIL- STD-129. (c.) Additional marking and/or bar coding requirements exceeding those of MIL-STD-129 (e.g., unit serial numbers, original equipment manufacturers (OEM) name, or OEM model number, as specified on the AFMC Form 158.

ORGANIZATION / OFFICE SYMBOL:

406 SCMS / GULAA

PACKAGING SPECIALIST:

Strain, Verlisher M

PHONE NUMBER:

405-582-9761 / 852-9761

SIGNATURE:

//SIGNED//Strain, Verlisher M

DATE:

18277 - 04 OCT 2018

Page 1 of 1AFMC 158 Version 1Generated by PRPS using Jasper Reports on 02 Nov 2018

TRANSPORTATION DATA FOR SOLICITATIONS

COMMODITY: See Continuation

PURCHASE INSTRUMENT NUMBER:

FD20301900220-00

DATE INITIATED:

04 OCT 2018

STOCK NUMBER: See Continuation

X ORIGIN DESTINATION OTHER X DATA / FIRST ARTICLE F.O.B. DESTINATION(Specify)

F.O.B. TERMS RECOMMENDED AS BEST SUITED FOR THIS PROCUREMENT

TRANSPORTATION PROVISIONS / CLAUSES FAR CITATION

F.O.B. Origin 52.247-29 Freight Classification Description 52.247-53 Contact DCMA Transportation Contact DCMA Transportation on ALL "DCMA Administered" contracts prior to shipment for shipping instructions using the DCMA Shipment Instruction Request (SIR) eTool System, at http://www.dcma.mil <http://www.dcma.mil/> for ALL FOB:

Origin, Foreign Military Sales (FMS), and FOB: Destination OCONUS/Export movements to obtain the appropriate DOD regulatory clearances, shipping documentation and instructions from your cognizant DCMA Transportation Office. If you are new to DCMA, and do not already have a SIR eTool account, you will first need to request an account via DCMA External Web Access Management (EWAM) application which can be accessed at http://www.dcma.mil. If you need additional assistance, email DCMA Transportation Group at: Transportation.Division@dcma.mil. Do not move any freight to a water or aerial port prior to contacting DCMA or it will become frustrated. Failure to contact the responsible DCMA may result in vendor incurring additional expenditures.

Vendor Transportation Instructions

TACRN:

AAA

TRANSPORTATION FUNDS INFORMATION:

Purchase Instrument Line LOA: 97X4930.FC04 648 47GT 15B01E 01N000 00000 000000 503000 F03000 FSR: 013352 PSR: K15278

First Destination Transportation Account Code: FRS2

Miscellaneous Obligation / Reimbursement Document:

Second Destination Transportation Account Code:

FMS LOA:

Additional Funding Information:

ADVANCE PR

ITEM / SHIP TO(s):

NSN / Pseudo NSN: 2840012594369JF

Purchase Instrument Line Item Number: 0002

Ship to (DoDAAC / MAPAC): FY2303

Mark For: FA moniter

Ship To (Address): FY2303 DDOO SOP 1ST ARTICLE

8080 PERIMETER RD BLDG 18 DR 16

TINKER AFB OK 73145

73145 - 3145

USA

WPOD:

APOD:

BBP / CCP:

RIC: 0

Requisition Number:

Supplemental Address:

FMS Case:

CP 405 739 8596

Ship To (Remarks):

Page 1 of 3DD FORM 1653 Version 1Generated by PRPS using Jasper Reports on 02 Nov 2018

Purchase Instrument Line Item Number: 0003

Ship to (DoDAAC / MAPAC): FY2303

Mark For: FA moniter

Ship To (Address): FY2303 DDOO SOP 1ST ARTICLE

8080 PERIMETER RD BLDG 18 DR 16

TINKER AFB OK 73145

73145 - 3145

RIC: 0

CP 405 739 8596

EVALUATION OF PORT BID OR PROPOSAL:

SOLICITATION DATA NOTES:

OTHER TRANSPORTATION DATA:

TACRN:

AAB

TRANSPORTATION FUNDS INFORMATION:

Purchase Instrument Line LOA: 97X4930.FC04 648 47GT 15B01E 01N000 00000 000000 503000 F03000 FSR: 013352 PSR: K15278

First Destination Transportation Account Code: FRS2

Miscellaneous Obligation / Reimbursement Document:

Second Destination Transportation Account Code:

FMS LOA:

Additional Funding Information:

ADVANCE PR

ITEM / SHIP TO(s):

Purchase Instrument Line Item Number: 0001

Ship to (DoDAAC / MAPAC): SW3211

Mark For: ACCT 09

Ship To (Address): DLA DISTRIBUTION DEPOT OKLAHOMA

TINKER AFB OK 73145-8000

73145 - 8000

RIC: 1

3301 F AVE CEN REC BLDG 506 DR 22

EVALUATION OF PORT BID OR PROPOSAL:

SOLICITATION DATA NOTES:

Page 2 of 3DD FORM 1653 Version 1Generated by PRPS using Jasper Reports on 02 Nov 2018

OTHER TRANSPORTATION DATA:

NAME

Pate, Robert T

ORGANIZATION / OFFICE

SYMBOL

406 SCMS / GULAA

COMMERCIAL / DSN

PHONE

478-926-2771 / 468-2771

SIGNATURE

//SIGNED//Pate, Robert T

DATE

04 OCT 2018

Page 3 of 3DD FORM 1653 Version 1Generated by PRPS using Jasper Reports on 02 Nov 2018

ENGINEERING DATA LIST

10 OCT 2018

REVISION: 8 *HISTORY*

CAGE:

07482

PAGE:

NSN:

DATA TECH:

Logan, Jamie

END ITEM:

F101

ORGANIZATION/OFFICE SYMBOL:

429 SCMS GUMAC/

MANUFACTURER NAME:

GENERAL ELECTRIC COMPANY

REFERENCE NUMBER:

7089M92G03

NOUN:

FRAME,FRONT,AIRCRAF

LINE/

SUB CAGE

ENG DRAWING NUM/ ACCOMP

DOC NUM REV

NR

SHEETS

FURN

CODE

DIST

CODE NOUN REMARKS

L 07482 7089M92 F S FRAME SUPPLY (WELDMENT) Logan, Jamie 10 OCT 2018

G03

NAME: DATE:

L 07482 PL7089M92 G S PARTS LIST

L 07482 5037M16 S TUBE, COOLING FLOW

L 07482 5037M53 S TUBE, LUBE MAKE UP-FWD

L 07482 5037M65 S TUBE, PRESSURE FILL

L 07482 5037M71 S TUBE, LUBE MAKE-UP AFT

L 07482 5037M93 S TUBE, HYDRAULIC SUPPLY

L 07482 5037M94 B S TUBE, SCAVENGE RETURN

L 07482 7084M40 S TUBE, HYDRAULIC MAKE-UP

L 07482 7084M41 B S DEAERATOR BOX, OIL TANK-

CASTING

L 07482 7084M42 A S DEAERATOR BOX, OIL TANK

L 07482 7089M90 S PLATE, OIL TANK-CASTING

L 07482 7089M91 S PLATE, OIL TANK

L 07482 7090M60 B S DEAERATOR-CASTING

L 07482 7090M61 C S DEAERATOR

L 07482 7090M62 S PLATE, COVER

L 07482 7090M63 A S DEAERATOR (WELDMENT)

L 07482 PL7090M63 A S PARTS LIST

L 07482 7115M78 S TUBE, HYDRAULIC RETURN

L 07482 8311253 M GE PHOTO Logan, Jamie 10 OCT 2018

PHOTO REQUIRED---FURNISHED BY PCO UPON REQUEST AFTER AWARD.

L 07482 J970 AF S INSERT, SCREW THREAD,

SELF-LOCKING

L 07482 P1TF3 S INTERPRETATION OF

DRAWING

Logan, Jamie 10 OCT 2018

REVISION CODE S34

L 07482 P1TF9 S MACHINED FEATURES Logan, Jamie 10 OCT 2018

REVISION CODE S14

C - CLASSIFIED DOCUMENT.

S - FURNISHED WITH SOLICITATION.

M - STABLE BASE DRAWING REQUIRED; FURNISHED WITH

CONTRACT AWARD.

X - DATA SUPPLIED (NOT IN JEDMICS).

R - FURNISHED BY PCO UPON REQUEST.

P - PARTIAL DOCUMENT FURNISHED.

V - VENDOR DRAWING; (NOT PROVIDED).

G - GOV'T DOCUMENT.

O - OTHERS, CONTRACTOR MUST ACQUIRE.

A- DATA NOT AVAILABLE.

FURNISHED METHOD CODE LEGEND:

Page 1 of 3EDL Version 8Generated by PRPS using Jasper Reports on 02 Nov 2018

L 07482 P1TF10 S FABRICATED ASSEMBLIES Logan, Jamie 10 OCT 2018

REVISION CODE S14

L 07482 P1TF11 S CAST & FORGED PARTS Logan, Jamie 10 OCT 2018

REVISION CODE S6

L 07482 P3TF2 S FLUORESCENT PENETRANT

INSPECTION

REVISION CODE S29

L 07482 P3TF5 S RADIOGRAPHIC INSPECTION Logan, Jamie 10 OCT 2018

REVISION CODE S16

L 07482 P8TF3 S GAS SHIELDED ARC WELDING Logan, Jamie 10 OCT 2018

REVISION CODE S20

L 07482 P12TF24 S INSTALLATION OF KEY TYPE

INSERTS AND STUDS

REVISION CODE S9

L 07482 P13TF1 S FORMED TUBING Logan, Jamie 10 OCT 2018

REVISION CODE S20

L 07482 P21TF6 S IN-PROCESS WELDING OF

CASTINGS

REVISION CODE S21

L 07482 P23TF3 S IDENTIFICATION MARKING Logan, Jamie 10 OCT 2018

REVISION CODE S40

L 00000 AIA/NAS NASM33537 O INSERT, SCREW THREAD

L 00000 AMS 2175 O CASTINGS

L 00000 AMS 4080 O ALUMINUM ALLOY

L 00000 AMS 4116 O ALUMINUM ALLOY

L 00000 AMS 4233 O ALUMINUM ALLOY, WELDING

WIRE

L 00000 AS 8879 O SCREW THREADS

L 00000 MIL-C-5541 O CHEMICAL CONVERSION

COATINGS ON ALUMINUM

L 00000 MIL-L-7808 O LUBRICATING OIL

Page 2 of 3EDL Version 8Generated by PRPS using Jasper Reports on 02 Nov 2018

L 00000 MIL-STD-276 O IMPREGNATION OF CASTINGS

L 00000 MIL-STD-130 O PART MARKING

STANDARD ENGINEERING TEXT

1. RELEASE OF THIS DATA TO A FOREIGN-OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

2. THE CONTRACTOR SHALL USE THE MOST CURRENT AMENDMENTS APPLICABLE TO EACH MIL SPEC, MIL STD, INDUSTRY SPEC OR INDUSTRY STD AS OF THE EFFECTIVE DATE OF THIS

CONTRACT UNLESS OTHERWISE NOTED.

Page 3 of 3EDL Version 8Generated by PRPS using Jasper Reports on 02 Nov 2018

FIRST ARTICLE REQUIREMENTS 1. DATE

19 MAR 2012(AFMCI 64-110, AFMCI 23-102 and FAR Part 9, Sub Part 9.3)(Additional Instructions on Page 3)

2. PR / MIPR NUMBER 3. CAGE / REFERENCE NUMBER

07482 / 7089M92G03

4. NSN

5. FIRST ARTICLE QUANTITY

THE FIRST ARTICLE IS 3 UNIT(S) OF LOT / ITEM EA

AND WILL BE: PART OF PRODUCTION QUANTITY X IN ADDITION TO PRODUCTION QUANTITY

6. ARTICLES

WILL X WILL NOT SERVE AS A MANUFACTURING STANDARD

7. LONG LEAD TIME ITEMS

X REQUIRED NOT REQUIRED

(See FAR 52.209-3 OR -4, alternate II)

8. SPECIAL REQUIREMENT/PRODUCTION FACILITIES (See FAR 52.209-3 OR -4 Alternate I)

X REQUIRED NOT REQUIRED

"The First Article offered must be manufactured at the facilities in which that item is to be produced under the contract, or if the First Article is a component not manufactured by the contractor, such component must be manufactured at the facilities in which the component is to be produced for the contract. A certification to this effect must accompany each First Article which is offered."

9. TEST / INSPECTION REQUIREMENTS

A.

X

CONTRACTOR TESTING

GOVERNMENT TESTING

Performance or other characteristics which the First Articles must meet are

As specified on the part drawing, in the referenced/called out specifications, and on the engineering instruction sheet.

B. The detailed technical requirements for First Article approval tests are contained in

As specified on the part drawing, in the referenced/called out specifications, and on the engineering instruction sheet. Material certifications must be provided by contractor with first article delivery.

(Cite Spec and Para number)

C. TEST PLAN REQUIRED

Number of days for government approval / disapproval days.

D. Contractor's notification to ACO and

(Requesting Activity) of test time and location due days prior to start of testing.

E. TEST REPORT REQUIRED

(1) Forwarded to

(2) Government written notice of approval / disapproval due days after receipt of contractor's report.

F. FIRST ARTICLE DELIVERY

(1) Due within 180 calendar days from date contract.

(2) Notify 30 calendar days prior to shipment.

(3) Delivered to government at

SEE BLOCK 12

(Set Forth Consignee and Address)

(4) Government written notice of approval / disapproval within 120 days after receipt of first article package.

G. Estimated cost of government testing / inspection evaluation.

$16,778.6200

Page 1 of 3AFMC IMT 260, 20020830, V-3 Version 1Generated by PRPS using Jasper Reports on 02 Nov 2018

19 MAR 2012(AFMCI 64-110, AFMCI 23-102 and FAR Part 9, Sub Part 9.3)(Additional Instructions on Page 3)

10. DISPOSITION OF FIRST ARTICLES

X Approved First Articles will be forwarded to

USAF Supply

X 1 (insert quantity) First Articles will be expended in testing. Residual components of disapproved First Articles will be returned to the contractor

X will be retained by USAF pending disposition instructions from the contractor.

X First Articles will be installed on aircraft/equipment to determine proper fit/function. Approved article will remain on the aircraft/equipment and will not be forwarded to USAF Supply, but will be considered part of the contract quantity.

X Disapproved First Articles will be returned to the contractor

X will be retained by USAF pending disposition instructions from the contractor.

On purchase requests designated as direct shipments the following disposition will apply. (NOTE: Always applicable on Foreign Military Sales (FMS)).

a. Approved First Articles will be returned to the contractor for shipment with production item.

b. Disposition of disapproved First Articles will remain the same as marked above.

Other Disposition:

11. CONDITION(S) FOR WAIVER OF FIRST ARTICLE APPROVAL

a. Offerors who have previously furnished production quantities of the same or similar article to the prime contractor for delivery to the Government, DoD, Air Force.

b. Offerors currently in production of the same or similar article for a Government, DoD, Air Force contract and who have received First Article approval under the existing contract.

c. Offerors who have previously furnished production quantities of the same or similar articles to the Government, DoD, Air Force, provided articles thus furnished, have exhibited satisfactory performance in service in the opinion of the Air Force.

d. Provided not more than months have elapsed since completion of the contract.

e. First Article testing will not be waived.

f. X See Remarks in block 12 below.

NOTE TO BUYER: UNDER CONDITIONS A AND C ABOVE, THE COGNIZANT ENGINEERING ACTIVITY WILL DECIDE WHETHER OR NOT THE ITEM HAS EXHIBITED SATISFACTORY PERFORMANCE IN SERVICE AND PREPARE AND RETAIN SUPPORTING DOCUMENTATION TO FULLY JUSTIFY THIS DECISION. THE BUYER MUST SOLICIT DUAL PRICES (That is, both with and without requirement for first article approval) AND MUST FURNISH THE COGNIZANT ENGINEERING ACTIVITY WITH THE FOLLOWING INFORMATION ON THE PREVIOUSLY SUPPLIED ARTICLE:

A. PROCURING OFFICE B. CONTRACT NUMBER C. DATE OF CONTRACT D. SPECIFICATION NUMBER AND REVISION

12. REMARKS

Lucas, Hunter DNAME: 21 MAR 2012DATE:

THE INTEGRITY, FIT, AND FUNCTION OF THIS ITEM IS CRITICAL TO SAFE FLIGHT AND ENGINE OPERATION. IN ORDER TO COMPLY WITH DRAWING SPECIFIED DIMENSIONAL TOLERANCES, MATERIAL CERTIFICATIONS, AND PROCESS REQUIREMENTS, A CONTRACTOR MUST HAVE EXPERTISE, SOPHISTICATED FACILITIES, AND BE ABLE TO IMPLEMENT STRINGENT QUALITY CONTROLS. IT IS THEREFORE NECESSARY TO VERIFY THE CONTRACTORS ABILITY TO PRODUCE THIS ITEM. CONDITIONS FOR FIRST ARTICLE WAIVER ARE AS OUTLINED IN BLOCK 11 ABOVE. A FIT CHECK MAY BE PERFORMED AT THE DISCRETION OF THE COGNIZANT ENGINEER OVERSEEING FIRST ARTICLE TESTING.

DELIVER GOVERNMENT FIRST ARTICLES TO:

DDOO-SOP (First Article) Bldg 18 Door 16 8080 Perimeter Rd Tinker AFB, OK 73145-8000

(405) 739-7667

DODAAC:FY2303

MARK FOR: FIRST ARTICLES

Attn: DDOO-SOP

DO NOT POST NON-ACCOUNTABLE

DO NOT PUT IN SUPPLY

DODAAC:FY2303

NOTE: Please insure that the words "FIRST ARTICLE" are clearly and conspicuously marked on the outside of the shipping container/package.

Page 2 of 3AFMC IMT 260, 20020830, V-3 Version 1Generated by PRPS using Jasper Reports on 02 Nov 2018

19 MAR 2012(AFMCI 64-110, AFMCI 23-102 and FAR Part 9, Sub Part 9.3)(Additional Instructions on Page 3)

13. COGNIZANT ENG ORGANIZATION RESPONSIBLE FOR APPROVING TEST

(Name, Organization, Phone)

Lucas, Hunter D

OC-ALC

405-736-3482

336-3482

14. COGNIZANT ENG ORGANIZATION RESPONSIBLE FOR CONDUCTING

TEST (Name, Organization, Phone)

Page 3 of 3AFMC IMT 260, 20020830, V-3 Version 1Generated by PRPS using Jasper Reports on 02 Nov 2018