PID_Final.docx

Product Number: 2510015684920

GRILLE, METAL

NO DATA IS AVAILABLE. THE ALTERNATE OFFEROR IS

REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE

INCLUDING DATA FOR THE APPROVED AND ALTERNATE

PART FOR EVALUATION

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 1648474

Product Number: 2835014751320

CASE AND NOZZLE ASSEMBLY, TURBINE, NONAIRC

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

MIL-STD-130N (1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

CRITICAL APPLICATION ITEM

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 1212569

Product Number: 2910014247315

FILTER ELEMENT, FLUID.

THIS IS A FUEL FILTER, ONLY P/N 1R-0751 IS THE CORRECT

FORM, FIT AND FUNCTION FOR THIS APPLICATION.

CRITICAL APPLICATION ITEM

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 1R-0751

Product Number: 2910014387423

FILTER, FLUID

Configuration Change Management - Engineering Change Proposal, Requests for Variance (Deviation or Waiver) February 2015

1. Requirements A. The Configuration Change Management section of SAE EIA-649-1 Configuration Management Requirement for Defense Contracts, Paragraph 3.3, shall be used for Configuration Control of material purchased under this contract.

B. Furnished item(s) shall conform to the approved configuration requirements/revision specified, unless a Pre-Production Request for Variance (deviation) or a Post-Production Request for Variance (waiver), is processed and approved as provided by Paragraph 3. in this Standard Text Object (STO). Hereafter, the term "Request for Variance (RFV)" will also include Requests for Deviations and Waivers.

2. The definitions from EIA-649-1 apply to items being procured under this solicitation/contract, with the following clarification of Deviation & Waiver:

A. Pre-Production RFV (previously known as deviation) requests permission to produce a product that does not conform to contract requirements/documentation for a limited amount of time and for specified effectivity. (A deviation differs from an engineering change in that an approved engineering change requires corresponding revision of the item's current approved configuration documentation, whereas a deviation does not.).

B. Post-Production RFV (previously known as waiver) requests approval of product found during manufacture, or after having been submitted for Government inspection or acceptance, that departs from specified requirements, but nevertheless is considered suitable for use "as is" or after repair by an approved method.

3. Contractor responsibilities.

A. An Engineering Change Proposal (ECP) is used to make permanent changes in the Government technical data package (TDP). Pending approval of an ECP, contractual relief should be requested in writing by the Contractor using a RFV.

B. Refer to FAR Part 48 Value Engineering for cost saving improvements to the Technical Data Package (TDP).

C. All ECPs submitted by the Contractor will be deemed routine.

If the Contractor considers an ECP as an emergency or urgent; they shall include in their ECP submittal an explanation and all applicable supporting documentation. All ECPs will be reviewed for a determination on criticality, and, if concurred to be an emergency, the appropriate processing time-frame negotiated with the ESAs will be followed and the Contractor will be notified of anticipated response time.

D. For ECPs, Specification Change Notices (SCNs) or RFV, the Contractor must submit the applicable documentation listed in sub-paragraphs D.(1) through D.(4)to the Administrative Contracting Officer(ACO), with an information copy to the Procuring Contracting Officer (PCO). Failure to submit a complete legible package may result in return of the ECP/RFV without processing.

(1) Documentation listed in Paragraph 3.3.1 (for ECPs), 3.3.2 (RFV), 3.3.3 (for SCNs) or 3.3.4 (for Notices of Revision (NORs)) of the latest revision of EIA-649-1.

(2) DD Form 1692 (current revision) for ECP.

(3) DD Form 1694 (current revision) for RFV.

(4) DD Form 1695 (current revision) for NOR.

4. DLA's responsibilities:

A. Upon receipt of the ECP or RFV, the PCO will ensure that the applicable product specialist receives the copy from DCMA.

B. Within five (5) working days from the date of receipt of the Contractor's ECP or RFV from DCMA, the PS must submit the requests and any supporting documentation via a 339 to the appropriate Engineering Support Activity (ESA), when applicable.

C. Routine ECPs will be processed within 90 days from receipt by the ESA. RFVs will be evaluated and processed within 30 days from receipt by the ESA or as negotiated with the ESA.

(1) The contractor will be notified in writing of approval by the return of an approved copy of the ECP or RFV. Approval will be reflected by signature of the contracting activity or a review activity specifically identified in the contract.

(2) The contractor will be notified in writing of disapproval including reason(s) for disapproval.

5. For an approved RFV or an approved ECP, when the request affects the Contract, a modification will be issued to the contract incorporating the applicable requirement changes. Only a Contracting Officer is authorized to issue a modification incorporating the approved RFV and/or

ECP.

6. Questions regarding the status of previously submitted ECP or RFV should be directed to the PCO.

7. The submission of an ECP or RFV by the Contractor does not affect the required delivery date of the contract. If a delivery date change is needed, it must be negotiated with the Contracting Officer and documented via modification to the contract.

8. The period of time for evaluation and approval/disapproval of an ECP and/or a RFV, as specified in Paragraph 4. C., shall not constitute excusable delay in the performance of this Contract by the Contractor or in any way relieve the contractor from compliance with the contract delivery schedule. The submission of an ECP and/or RFV by the Contractor shall not preclude the Government from exercising its rights under any clause of the Contract. (End)

ADEQUATE DATA FOR THE EVALUATION OF ALTERNATE

OFFERS IS NOT AVAILABLE AT THE PROCUREMENT

AGENCY.THE OFFEROR MUST PROVIDE A COMPLETE

DATA PACKAGE INCLUDING DATA FOR THE APPROVED

AND ALTERNATE PART FOR EVALUATION.

CRITICAL APPLICATION ITEM

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 1G8878

Product Number: 2910014449487

FILTER, FLUID

Configuration Change Management - Engineering Change Proposal, Requests for Variance (Deviation or Waiver) February 2015

1. Requirements A. The Configuration Change Management section of SAE EIA-649-1 Configuration Management Requirement for Defense Contracts, Paragraph 3.3, shall be used for Configuration Control of material purchased under this contract.

B. Furnished item(s) shall conform to the approved configuration requirements/revision specified, unless a Pre-Production Request for Variance (deviation) or a Post-Production Request for Variance (waiver), is processed and approved as provided by Paragraph 3. in this Standard Text Object (STO). Hereafter, the term "Request for Variance (RFV)" will also include Requests for Deviations and Waivers.

2. The definitions from EIA-649-1 apply to items being procured under this solicitation/contract, with the following clarification of Deviation & Waiver:

A. Pre-Production RFV (previously known as deviation) requests permission to produce a product that does not conform to contract requirements/documentation for a limited amount of time and for specified effectivity. (A deviation differs from an engineering change in that an approved engineering change requires corresponding revision of the item's current approved configuration documentation, whereas a deviation does not.).

B. Post-Production RFV (previously known as waiver) requests approval of product found during manufacture, or after having been submitted for Government inspection or acceptance, that departs from specified requirements, but nevertheless is considered suitable for use "as is" or after repair by an approved method.

3. Contractor responsibilities.

A. An Engineering Change Proposal (ECP) is used to make permanent changes in the Government technical data package (TDP). Pending approval of an ECP, contractual relief should be requested in writing by the Contractor using a RFV.

B. Refer to FAR Part 48 Value Engineering for cost saving improvements to the Technical Data Package (TDP).

C. All ECPs submitted by the Contractor will be deemed routine.

If the Contractor considers an ECP as an emergency or urgent; they shall include in their ECP submittal an explanation and all applicable supporting documentation. All ECPs will be reviewed for a determination on criticality, and, if concurred to be an emergency, the appropriate processing time-frame negotiated with the ESAs will be followed and the Contractor will be notified of anticipated response time.

D. For ECPs, Specification Change Notices (SCNs) or RFV, the Contractor must submit the applicable documentation listed in sub-paragraphs D.(1) through D.(4)to the Administrative Contracting Officer(ACO), with an information copy to the Procuring Contracting Officer (PCO). Failure to submit a complete legible package may result in return of the ECP/RFV without processing.

(1) Documentation listed in Paragraph 3.3.1 (for ECPs), 3.3.2 (RFV), 3.3.3 (for SCNs) or 3.3.4 (for Notices of Revision (NORs)) of the latest revision of EIA-649-1.

(2) DD Form 1692 (current revision) for ECP.

(3) DD Form 1694 (current revision) for RFV.

(4) DD Form 1695 (current revision) for NOR.

4. DLA's responsibilities:

A. Upon receipt of the ECP or RFV, the PCO will ensure that the applicable product specialist receives the copy from DCMA.

B. Within five (5) working days from the date of receipt of the Contractor's ECP or RFV from DCMA, the PS must submit the requests and any supporting documentation via a 339 to the appropriate Engineering Support Activity (ESA), when applicable.

C. Routine ECPs will be processed within 90 days from receipt by the ESA. RFVs will be evaluated and processed within 30 days from receipt by the ESA or as negotiated with the ESA.

(1) The contractor will be notified in writing of approval by the return of an approved copy of the ECP or RFV. Approval will be reflected by signature of the contracting activity or a review activity specifically identified in the contract.

(2) The contractor will be notified in writing of disapproval including reason(s) for disapproval.

5. For an approved RFV or an approved ECP, when the request affects the Contract, a modification will be issued to the contract incorporating the applicable requirement changes. Only a Contracting Officer is authorized to issue a modification incorporating the approved RFV and/or

ECP.

6. Questions regarding the status of previously submitted ECP or RFV should be directed to the PCO.

7. The submission of an ECP or RFV by the Contractor does not affect the required delivery date of the contract. If a delivery date change is needed, it must be negotiated with the Contracting Officer and documented via modification to the contract.

8. The period of time for evaluation and approval/disapproval of an ECP and/or a RFV, as specified in Paragraph 4. C., shall not constitute excusable delay in the performance of this Contract by the Contractor or in any way relieve the contractor from compliance with the contract delivery schedule. The submission of an ECP and/or RFV by the Contractor shall not preclude the Government from exercising its rights under any clause of the Contract. (End)

WHEN THE PURCHASE ORDER TEXT (POT)

DESCRIBES THE REQUIRED PRODUCT(S) BY NAME AND

PART NUMBER OF A SPECIFIC ENTITY, BY THE NAMES

AND PART NUMBERS OF A NUMBER OF SPECIFIC

ENTITIES, OR BY THE NAME(S) AND PART NUMBER(S)

OF SPECIFIC ENTITY/ENTITIES AS MODIFIED BY

ADDITIONAL REQUIREMENTS SET FORTH IN THE POT

ONLY THAT/THOSE PRODUCT(S) HAVE BEEN DETERMINED

TO MEET THE NEEDS OF THE GOVERNMENT AND ARE

ACCEPTABLE. SUCH PRODUCT(S) ARE EXACT

PRODUCT(S) AS DEFINED IN DLAD 52.217-9002,

CONDITIONS FOR EVALUATION AND ACCEPTANCE OF

OFFERS FOR PART NUMBERED ITEMS.

A VENDOR OFFER/QUOTATION, BID WITHOUT

EXCEPTION, IS A CERTIFICATION THAT THE EXACT

PRODUCT, MANUFACTURED AND/OR SUPPLIED BY ONE

OF THE ENTITIES CITED IN THE POT WILL BE

FURNISHED UNDER THE CONTRACT OR ORDER. ANY

PRODUCT NOT MANUFACTURED AND/OR SUPPLIED

BY ONE OF THE ENTITIES CITED IN THE POT

IS AN ALTERNATE PRODUCT, EVEN THOUGH IT

MIGHT BE MANUFACTURED IN ACCORDANCE WITH THE

DRAWING(S) AND/OR SPECIFICATIONS OF ONE OF THE

ENTITIES CITED IN THE POT.

IF AN ALTERNATE PRODUCT IS FURNISHED UNDER A

CONTRACT OR ORDER FOR AN EXACT PRODUCT, THE

ALTERNATE PRODUCT WILL BE AN UNAUTHORIZED

SUBSTITUTION, AND MAY YIELD CRIMINAL PENALTIES

IN ADDITION TO ANY CIVIL REMEDIES AVAILABLE TO

THE GOVERNMENT.

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 1R0750

Product Number: 2935012869169

RING, WEARING

DSCR DOES NOT CURRENTLY HAVE AN APPROVED

TECHNICAL DATA PACKAGE AVAILABLE FOR THIS NSN.

DATA IS PROPRIETARY OR INSUFFICIENT FOR

COMPETITIVE PROCUREMENT.

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 8T7584

Product Number: 2940014554730

FILTER ELEMENT, FLUID.

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL

NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT

CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED

UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY

USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED

INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;

AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.

PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS

CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN

A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR

MERCURY COMPOUND. (IAW NAVSEA 5100-003D).

ADEQUATE DATA FOR THE EVALUATION OF ALTERNATE

OFFERS IS NOT AVAILABLE AT THE PROCUREMENT

AGENCY.THE OFFEROR MUST PROVIDE A COMPLETE

DATA PACKAGE INCLUDING DATA FOR THE APPROVED

AND ALTERNATE PART FOR EVALUATION.

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 1R0749

Product Number: 2940015131518

FILTER ELEMENT, FLUID.

Configuration Change Management - Engineering Change Proposal, Requests for Variance (Deviation or Waiver) February 2015

1. Requirements A. The Configuration Change Management section of SAE EIA-649-1 Configuration Management Requirement for Defense Contracts, Paragraph 3.3, shall be used for Configuration Control of material purchased under this contract.

B. Furnished item(s) shall conform to the approved configuration requirements/revision specified, unless a Pre-Production Request for Variance (deviation) or a Post-Production Request for Variance (waiver), is processed and approved as provided by Paragraph 3. in this Standard Text Object (STO). Hereafter, the term "Request for Variance (RFV)" will also include Requests for Deviations and Waivers.

2. The definitions from EIA-649-1 apply to items being procured under this solicitation/contract, with the following clarification of Deviation & Waiver:

A. Pre-Production RFV (previously known as deviation) requests permission to produce a product that does not conform to contract requirements/documentation for a limited amount of time and for specified effectivity. (A deviation differs from an engineering change in that an approved engineering change requires corresponding revision of the item's current approved configuration documentation, whereas a deviation does not.).

B. Post-Production RFV (previously known as waiver) requests approval of product found during manufacture, or after having been submitted for Government inspection or acceptance, that departs from specified requirements, but nevertheless is considered suitable for use "as is" or after repair by an approved method.

3. Contractor responsibilities.

A. An Engineering Change Proposal (ECP) is used to make permanent changes in the Government technical data package (TDP). Pending approval of an ECP, contractual relief should be requested in writing by the Contractor using a RFV.

B. Refer to FAR Part 48 Value Engineering for cost saving improvements to the Technical Data Package (TDP).

C. All ECPs submitted by the Contractor will be deemed routine.

If the Contractor considers an ECP as an emergency or urgent; they shall include in their ECP submittal an explanation and all applicable supporting documentation. All ECPs will be reviewed for a determination on criticality, and, if concurred to be an emergency, the appropriate processing time-frame negotiated with the ESAs will be followed and the Contractor will be notified of anticipated response time.

D. For ECPs, Specification Change Notices (SCNs) or RFV, the Contractor must submit the applicable documentation listed in sub-paragraphs D.(1) through D.(4)to the Administrative Contracting Officer(ACO), with an information copy to the Procuring Contracting Officer (PCO). Failure to submit a complete legible package may result in return of the ECP/RFV without processing.

(1) Documentation listed in Paragraph 3.3.1 (for ECPs), 3.3.2 (RFV), 3.3.3 (for SCNs) or 3.3.4 (for Notices of Revision (NORs)) of the latest revision of EIA-649-1.

(2) DD Form 1692 (current revision) for ECP.

(3) DD Form 1694 (current revision) for RFV.

(4) DD Form 1695 (current revision) for NOR.

4. DLA's responsibilities:

A. Upon receipt of the ECP or RFV, the PCO will ensure that the applicable product specialist receives the copy from DCMA.

B. Within five (5) working days from the date of receipt of the Contractor's ECP or RFV from DCMA, the PS must submit the requests and any supporting documentation via a 339 to the appropriate Engineering Support Activity (ESA), when applicable.

C. Routine ECPs will be processed within 90 days from receipt by the ESA. RFVs will be evaluated and processed within 30 days from receipt by the ESA or as negotiated with the ESA.

(1) The contractor will be notified in writing of approval by the return of an approved copy of the ECP or RFV. Approval will be reflected by signature of the contracting activity or a review activity specifically identified in the contract.

(2) The contractor will be notified in writing of disapproval including reason(s) for disapproval.

5. For an approved RFV or an approved ECP, when the request affects the Contract, a modification will be issued to the contract incorporating the applicable requirement changes. Only a Contracting Officer is authorized to issue a modification incorporating the approved RFV and/or

ECP.

6. Questions regarding the status of previously submitted ECP or RFV should be directed to the PCO.

7. The submission of an ECP or RFV by the Contractor does not affect the required delivery date of the contract. If a delivery date change is needed, it must be negotiated with the Contracting Officer and documented via modification to the contract.

8. The period of time for evaluation and approval/disapproval of an ECP and/or a RFV, as specified in Paragraph 4. C., shall not constitute excusable delay in the performance of this Contract by the Contractor or in any way relieve the contractor from compliance with the contract delivery schedule. The submission of an ECP and/or RFV by the Contractor shall not preclude the Government from exercising its rights under any clause of the Contract. (End)

NO DATA IS AVAILABLE. THE ALTERNATE OFFEROR IS

REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE

INCLUDING DATA FOR THE APPROVED AND ALTERNATE

PART FOR EVALUATION.

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 1R0739

Product Number: 2950011846057

TURBOSUPERCHARGER, AIRCRAFT RECIPROCATION ENGINE

Casting/forging may be required to manufacture this NSN. If a casting/forging is required, tooling is typically involved. The government may not have this special tooling. For sourcing, tooling, materials or other information, please contact the appropriate assistance team: (Aviation, C&E Supply Chains) DSCR.AFCAT@dla.mil; (Land & Maritime Supply Chains) DSCC.cast.forge@dla.mil

IDENTIFY TO MIL-STD-130

DSCR DOES NOT CURRENTLY HAVE AN APPROVED

TECHNICAL DATA PACKAGE AVAILABLE FOR THIS NSN.

DATA IS PROPRIETARY OR INSUFFICIENT FOR

COMPETITIVE PROCUREMENT.

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 8N5417

Product Number: 2950013747901

HOUSING, TURBOSUPERC

DSCR DOES NOT CURRENTLY HAVE AN APPROVED

TECHNICAL DATA PACKAGE AVAILABLE FOR THIS NSN.

DATA IS PROPRIETARY OR INSUFFICIENT FOR

COMPETITIVE PROCUREMENT.

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 1W4097

Product Number: 2990015254676

SENSOR, BAROMETRIC AND MANIFOLD PRESSURE, EMISSION

NO DATA IS AVAILABLE. THE ALTERNATE OFFEROR IS

REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE

INCLUDING DATA FOR THE APPROVED AND ALTERNATE

PART FOR EVALUATION

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 224-4536

Product Number: 3040014835429

CYLINDER ASSEMBLY, ACTUATING, LINEAR

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL

NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT

CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED

UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY

USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED

INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;

AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.

PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS

CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN

A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR

MERCURY COMPOUND. (IAW NAVSEA 5100-003D).

ADEQUATE DATA FOR THE EVALUATION OF ALTERNATE

OFFERS IS NOT AVAILABLE AT THE PROCUREMENT

AGENCY.THE OFFEROR MUST PROVIDE A COMPLETE

DATA PACKAGE INCLUDING DATA FOR THE APPROVED

AND ALTERNATE PART FOR EVALUATION.

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 3172440

Product Number: 3110001448265

BEARING, BALL, ANNULAR

NO DATA IS AVAILABLE. THE ALTERNATE OFFEROR IS

REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE

INCLUDING DATA FOR THE APPROVED AND ALTERNATE

PART FOR EVALUATION

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE

USED NOR INCORPORATED IN ANY ITEMS TO BE

DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION

SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT

DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.

SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR

APPROVAL UNLESS THEY ARE AUTHORIZED BY THE

SPECIFICATION REQUIREMENTS.

IDENTIFY TO:

MIL-STD-130N(1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

BEARING RESTRICTION:

AN AWARD FROM THIS SOLICITATION CAN ONLY BE MADE FOR A BEARING

MANUFACTURED IN THE UNITED STATES, ITS OUTLYING AREAS, OR CANADA AND FOR

EACH BALL OR ROLLER BEARING, THE COST OF THE BEARING COMPONENTS (BEARING

ELEMENT, RETAINER, INNER RACE, OR OUTER RACE) MANUFACTURED IN THE UNITED

STATES, ITS OUTLYING AREAS, OR CANADA MUST EXCEED 50% OF THE TOTAL COST

OF THE BEARING COMPONENTS OF THAT BALL OR ROLLER BEARING. SEE DFARS

CLAUSE 252.225-7016, RESTRICTION ON ACQUISITION OF BALL AND ROLLER

BEARINGS (DEC 2010). A CONTRACTOR'S DECLARATION ON THE DOMESTIC/FOREIGN

NATURE OF MATERIAL BEING OFFERED IS REQUIRED. PLEASE VISIT THE FOREIGN

BEARING WEBSITE AT http://www.dla.mil/Aviation/Business/IndustryResource s/DLAResourcesforSuppliers/ForeignBearingWaiver.aspx TO OBTAIN A COPY OF THE CONTRACTOR'S DECLARATION FORM. PLEASE PRINT

SIGN AND HAVE READY FOR SUBMISSION UPON REQUEST FROM THE BUYER. FAILURE

TO PROVIDE THIS INFORMATION MAY RESULT IN YOUR QUOTE NOT BEING

CONSIDERED FOR AWARD. IN THE EVENT NO OFFERED BEARINGS MEET THIS

SOURCING REQUIREMENT, THIS SOLICITATION MAY BE CANCELLED AND A WAIVER

MAY BE REQUESTED BY THE PROCUREMENT ACTIVITY. UPON RECEIPT OF AN

APPROVED WAIVER FROM THE DOMESTIC SOURCING RESTRICTION, THE REQUIREMENT

MAY BE RE-SOLICITED. SEE DFARS 225.7009-4, WAIVER, RESTRICTION ON BALL

AND ROLLER BEARINGS (DEC 2010).

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 1T0334

Product Number: 3110012500809

BEARING, BALL, ANNULAR

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

IDENTIFY TO

MIL-STD-130N (1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

BEARINGS RESTRICTION

AN AWARD FROM THIS SOLICITATION CAN ONLY BE MADE FOR A BEARING

MANUFACTURED IN THE UNITED STATES, ITS OUTLYING AREAS, OR CANADA AND FOR

EACH BALL OR ROLLER BEARING, THE COST OF THE BEARING COMPONENTS (BEARING

ELEMENT, RETAINER, INNER RACE, OR OUTER RACE) MANUFACTURED IN THE UNITED

STATES, ITS OUTLYING AREAS, OR CANADA MUST EXCEED 50% OF THE TOTAL COST

OF THE BEARING COMPONENTS OF THAT BALL OR ROLLER BEARING. SEE DFARS

CLAUSE 252.225-7016, RESTRICTION ON ACQUISITION OF BALL AND ROLLER

BEARINGS (DEC 2010). A CONTRACTOR'S DECLARATION ON THE DOMESTIC/FOREIGN

NATURE OF MATERIAL BEING OFFERED IS REQUIRED. PLEASE VISIT THE FOREIGN

BEARING WEBSITE AT http://www.dla.mil/Aviation/Business/IndustryResource s/DLAResourcesforSuppliers/ForeignBearingWaiver.aspx TO OBTAIN A COPY OF THE CONTRACTOR'S DECLARATION FORM. PLEASE PRINT

SIGN AND HAVE READY FOR SUBMISSION UPON REQUEST FROM THE BUYER. FAILURE

TO PROVIDE THIS INFORMATION MAY RESULT IN YOUR QUOTE NOT BEING

CONSIDERED FOR AWARD. IN THE EVENT NO OFFERED BEARINGS MEET THIS

SOURCING REQUIREMENT, THIS SOLICITATION MAY BE CANCELLED AND A WAIVER

MAY BE REQUESTED BY THE PROCUREMENT ACTIVITY. UPON RECEIPT OF AN

APPROVED WAIVER FROM THE DOMESTIC SOURCING RESTRICTION, THE REQUIREMENT

MAY BE RE-SOLICITED. SEE DFARS 225.7009-4, WAIVER, RESTRICTION ON BALL

AND ROLLER BEARINGS (DEC 2010).

SAMPLING

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 2D5658

Product Number: 3110013406836

BEARING, ROLLER, CYLINDRICAL

NO DATA IS AVAILABLE. THE ALTERNATE OFFEROR IS

REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE

INCLUDING DATA FOR THE APPROVED AND ALTERNATE

PART FOR EVALUATION

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE

USED NOR INCORPORATED IN ANY ITEMS TO BE

DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION

SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT

DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.

SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR

APPROVAL UNLESS THEY ARE AUTHORIZED BY THE

SPECIFICATION REQUIREMENTS

MIL-STD-130N (1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL

NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT

CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED

UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY

USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED

INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;

AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.

PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS

CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN

A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR

MERCURY COMPOUND. (IAW NAVSEA 5100-003D).

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 4M6107

Product Number: 3110014735128

BEARING, ROLLER, SELF

NO DATA IS AVAILABLE. THE ALTERNATE OFFEROR IS

REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE

INCLUDING DATA FOR THE APPROVED AND ALTERNATE

PART FOR EVALUATION.

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE

USED NOR INCORPORATED IN ANY ITEMS TO BE

DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION

SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT

DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.

SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR

APPROVAL UNLESS THEY ARE AUTHORIZED BY THE

SPECIFICATION REQUIREMENTS.

MIL-STD-130N(1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

BEARING RESTRICTION:

AN AWARD FROM THIS SOLICITATION CAN ONLY BE MADE FOR A BEARING

MANUFACTURED IN THE UNITED STATES, ITS OUTLYING AREAS, OR CANADA AND FOR

EACH BALL OR ROLLER BEARING, THE COST OF THE BEARING COMPONENTS (BEARING

ELEMENT, RETAINER, INNER RACE, OR OUTER RACE) MANUFACTURED IN THE UNITED

STATES, ITS OUTLYING AREAS, OR CANADA MUST EXCEED 50% OF THE TOTAL COST

OF THE BEARING COMPONENTS OF THAT BALL OR ROLLER BEARING. SEE DFARS

CLAUSE 252.225-7016, RESTRICTION ON ACQUISITION OF BALL AND ROLLER

BEARINGS (DEC 2010). A CONTRACTOR'S DECLARATION ON THE DOMESTIC/FOREIGN

NATURE OF MATERIAL BEING OFFERED IS REQUIRED. PLEASE VISIT THE FOREIGN

BEARING WEBSITE AT http://www.dla.mil/Aviation/Business/IndustryResource s/DLAResourcesforSuppliers/ForeignBearingWaiver.aspx TO OBTAIN A COPY OF THE CONTRACTOR'S DECLARATION FORM. PLEASE PRINT

SIGN AND HAVE READY FOR SUBMISSION UPON REQUEST FROM THE BUYER. FAILURE

TO PROVIDE THIS INFORMATION MAY RESULT IN YOUR QUOTE NOT BEING

CONSIDERED FOR AWARD. IN THE EVENT NO OFFERED BEARINGS MEET THIS

SOURCING REQUIREMENT, THIS SOLICITATION MAY BE CANCELLED AND A WAIVER

MAY BE REQUESTED BY THE PROCUREMENT ACTIVITY. UPON RECEIPT OF AN

APPROVED WAIVER FROM THE DOMESTIC SOURCING RESTRICTION, THE REQUIREMENT

MAY BE RE-SOLICITED. SEE DFARS 225.7009-4, WAIVER, RESTRICTION ON BALL

AND ROLLER BEARINGS (DEC 2010).

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 4D4431

Product Number: 3120001183007

BEARING, WASHEER, THRUST

SOURCE CONTROL ITEM

U S ARMY TANK AUTOMOTIVE COMMAND

CAGE: 19207

DRAWING: 11634713

P/N: 11634713

THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM - (TO INCLUDE 'COMMERCIAL

OF A TYPE')

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL

NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT

CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED

UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY

USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED

INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;

AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.

PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS

CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN

A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR

MERCURY COMPOUND. (IAW NAVSEA 5100-003D).

NOTE: THE CITED DRAWING IS A SOURCE CONTROLLED

DRAWING AND AS OF THE DATE OF THIS SOLICITATION

ONLY THE SOURCE(S) CITED ON THE DRAWING HAVE

BEEN APPROVED. EVEN THOUGH SOURCES AND APPROVED

PART NUMBERS ARE PROVIDED, THE ITEMS

FURNISHED MUST MEET THE REQUIREMENTS OF THE

CITED DRAWING. OFFERORS WHO ARE INTERESTED IN

QUALIFYING THEIR PRODUCT FOR PURPOSE OF FUTURE

ACQUISITION MUST CONTACT THE COGNIZANT DESIGN

ACTIVITY SPECIFIED ON THE SOURCE CONTROLLED

DRAWING.

ALSO, MAY INCLUDE ADDITIONAL APPROVED SOURCES

THAT HAVE NOT BEEN REFLECTED ON THE DRAWING AT

THIS TIME.

NO DATA IS AVAILABLE. THE ALTERNATE OFFEROR IS

REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE

INCLUDING DATA FOR THE APPROVED AND ALTERNATE

PART FOR EVALUATION.

THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO

EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA

AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED

THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE

DEPARTMENTS OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO

INTERNATIONAL AGREEMENTS.

TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, MILITARY

CRITICAL TECHNICAL DATA AGREEMENT, FORM IS AVAILABLE AT THE WORLD WIDE

WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO:

DLA LOGISTICS INFORMATION SERVICE

FEDERAL CENTER

74 WASHINGTON AVE., NORTH

BATTLE CREEK, MI 49037-3084

TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A

CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT,

DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY

THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN

EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 EXEMPTIONS OF

GENERAL APPLICABILITY, AND/OR EAR PART 740 ARE APPLICABLE.

NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL

DATA ARE REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN

APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO

RECEIVE A COPY OF THE EXPORT CONTROLLED TECHNICAL DATA.

NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO

THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA

UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY

PERMITTED BY DODD 5230.25.

CRITICAL APPLICATION ITEM

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 11634713

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 7M7193

IAW BASIC DRAWING NR 19207 11634713

REVISION NR DTD 01/14/1967

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 11634713

REVISION NR DTD 04/07/2014

PART PIECE NUMBER:

Product Number: 3120009482181

BEARING HALF, SLEEVE

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

AN AWARD FROM THIS SOLICITATION CAN ONLY BE MADE FOR A BEARING

MANUFACTURED IN THE UNITED STATES, ITS OUTLYING AREAS, OR CANADA AND FOR

EACH BALL OR ROLLER BEARING, THE COST OF THE BEARING COMPONENTS (BEARING

ELEMENT, RETAINER, INNER RACE, OR OUTER RACE) MANUFACTURED IN THE UNITED

STATES, ITS OUTLYING AREAS, OR CANADA MUST EXCEED 50% OF THE TOTAL COST

OF THE BEARING COMPONENTS OF THAT BALL OR ROLLER BEARING. SEE DFARS

CLAUSE 252.225-7016, RESTRICTION ON ACQUISITION OF BALL AND ROLLER

BEARINGS (DEC 2010). A CONTRACTOR'S DECLARATION ON THE DOMESTIC/FOREIGN

NATURE OF MATERIAL BEING OFFERED IS REQUIRED. PLEASE VISIT THE FOREIGN

BEARING WEBSITE AT http://www.dla.mil/Aviation/Business/IndustryResource s/DLAResourcesforSuppliers/ForeignBearingWaiver.aspx TO OBTAIN A COPY OF THE CONTRACTOR'S DECLARATION FORM. PLEASE PRINT

SIGN AND HAVE READY FOR SUBMISSION UPON REQUEST FROM THE BUYER. FAILURE

TO PROVIDE THIS INFORMATION MAY RESULT IN YOUR QUOTE NOT BEING

CONSIDERED FOR AWARD. IN THE EVENT NO OFFERED BEARINGS MEET THIS

SOURCING REQUIREMENT, THIS SOLICITATION MAY BE CANCELLED AND A WAIVER

MAY BE REQUESTED BY THE PROCUREMENT ACTIVITY. UPON RECEIPT OF AN

APPROVED WAIVER FROM THE DOMESTIC SOURCING RESTRICTION, THE REQUIREMENT

MAY BE RE-SOLICITED. SEE DFARS 225.7009-4, WAIVER, RESTRICTION ON BALL

AND ROLLER BEARINGS (DEC 2010).

ALL CLASS 3A AND 3B THREADS SHALL BE GAGED

I/A/W CATEGORY 1 PER SAE AS8879 OR "SAFETY

CRITICAL THREADS" PER MIL-S-7742 UNLESS

OTHERWISE SPECIFIED. THE ABOVE EXCLUDES

SELF-LOCKING NUTS AND INTERNAL THREADS SMALLER

THAN .190 DIA. AND EXTERNAL THREADS SMALLER

THAN .138 DIA.

MIL-STD-1647E, DATED 21 APRIL 2003.

IDENTIFICATION MARKINGS FOR DOMESTICALLY

MANUFACTURED BEARINGS, BALL, ANNULAR FOR

INSTRUMENTS AND PRECISION COMPONENTS.

IDENTIFY TO:

MIL-STD-130N(1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

SAMPLING:

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 3J2443

Product Number: 3120011655662

ROLLER, LINEAR, ROTARY MOTION

IDENTIFY TO:

MIL-STD-130N (1) DATED 16 NOV 2012.

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 7S5386

Product Number: 3120011666920

BEARING, WASHER, THRUST

IDENTIFY TO:

MIL-STD-130N (1) DATED 16 NOV 2012.

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 6G3206

Product Number: 3120012109465

BEARING, SLEEVE

NO DATA IS AVAILABLE. THE ALTERNATE OFFEROR IS

REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE

INCLUDING DATA FOR THE APPROVED AND ALTERNATE

PART FOR EVALUATION.

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE

USED NOR INCORPORATED IN ANY ITEMS TO BE

DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION

SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT

DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.

SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR

APPROVAL UNLESS THEY ARE AUTHORIZED BY THE

SPECIFICATION REQUIREMENTS.

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL

NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT

CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED

UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY

USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED

INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;

AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.

PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS

CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN

A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR

MERCURY COMPOUND. (IAW NAVSEA 5100-003D).

CATERPILLAR INC. DBA CATERPILLAR 11083 P/N 4W5698

Product Number: 3120012573297

BEARING, SLEEVE

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

AN AWARD FROM THIS SOLICITATION CAN ONLY BE MADE FOR A BEARING

MANUFACTURED IN THE UNITED STATES, ITS OUTLYING AREAS, OR CANADA AND FOR

EACH BALL OR ROLLER BEARING, THE COST OF THE BEARING COMPONENTS (BEARING

ELEMENT, RETAINER, INNER RACE, OR OUTER RACE) MANUFACTURED IN THE UNITED

STATES, ITS OUTLYING AREAS, OR CANADA MUST EXCEED 50% OF THE TOTAL COST

OF THE BEARING COMPONENTS OF THAT BALL OR ROLLER BEARING. SEE DFARS

CLAUSE 252.225-7016, RESTRICTION ON ACQUISITION OF BALL AND ROLLER

BEARINGS (DEC 2010). A CONTRACTOR'S DECLARATION ON THE DOMESTIC/FOREIGN

NATURE OF MATERIAL BEING OFFERED IS REQUIRED. PLEASE VISIT THE FOREIGN

BEARING WEBSITE AT http://www.dla.mil/Aviation/Business/IndustryResource s/DLAResourcesforSuppliers/ForeignBearingWaiver.aspx TO OBTAIN A COPY OF THE CONTRACTOR'S DECLARATION FORM. PLEASE PRINT

SIGN AND HAVE READY FOR SUBMISSION UPON REQUEST FROM THE BUYER. FAILURE

TO PROVIDE THIS INFORMATION MAY RESULT IN YOUR QUOTE NOT BEING

CONSIDERED FOR AWARD. IN THE EVENT NO OFFERED BEARINGS MEET THIS

SOURCING REQUIREMENT, THIS SOLICITATION MAY BE C