PGC 02851 tech data

COAT, ALL WEATHER, WOMAN'S, PEWTER

NEW DESIGN

ADDITIONAL INFORMATION FOR PD 03-09:

PATTERN DATE: 22 NOVEMBER 2002

STANDARD SAMPLE FOR CLOTH, POPLIN, POLYESTER

AND COTTON (WATER REPELLENT), MARINE CORPS PEWTER

2246 CONFORMING TO A-A-50531 IS AVAILABLE FOR

SHADE, FINISH & COLORFASTNESS ON ROLL NO. 1208-06

THIS SAMPLE SHALL SHOW COLORFASTNESS IN

ACCORDANCE WITH THE TABLE BELOW.

CHARACTERISTICS REQUIREMENT TEST METHOD

LAUNDERING (MIN) EQUAL TO STANDARD AATCC 61 3A

AFTER 3 CYCLES GRADE 4 AATCC 61 3A

CROCKING (MIN) GRADE 2.5 AATCC 8

LIGHT (MIN) GRADE 4 AATCC 16 OPT A

INTERIM CHANGES TO PD-03-08

PAGE 1, PARA. 2, IN *SCHEDULE OF SIZES): ADD

SIZE 12 AND 14 FOR *EXTRA LONG)

.PAGE 11, PARA.3.7. FINISHED MEASUREMENTS, TABLE 1V

UNDER *BACK LENGTH TYPE II) FOR SIZE 12XL ADD *48

AND FOR SIZE 14XL ADD *48 1/4"

PAGE 12, PARA. 3.7.1, LINER MEASUREMENTS, TABLE V

UNDER *BACK LENGTH, TYPE II FOR SIZE 12XL ADD

*37-3/4) AND FOR SIZE 14XL ADD *38)

INTERIM CHANGES TO CR/PD 03-09

PAGE 1, SCHEDULE OF SIZES, DELETE ENTIRELY AND

SUBSTITUTE THE FOLLOWING:

"SHORT REG LONG XLONG

XO XO XO ---

2 2 2 --- 4 4 4 --- 6 6 6 --- 8 8 8 --- 10 10 10 --- 12 12 12 12 14 14 14 14 16 16 16 16 18 18 18 18 20 20 20 20 --- 22 22 22 --- 24 --- --- --- 26 --- ---

PAGE 2, PARAGRAPH 3.1 DESCRIPTION. LINE 5

AFTER "5" ADD "THE MATERIAL FOR THE SLEEVE

LINING SHALL BE TAFFETA AS SPECIFIED

IN PARAGRAPH 3.3.2.2.)

LINE 5, DELETE "1/4" AND SUBSTITUTE "3/8".

PAGE 2, PARAGRAPH 3.1.1, BELT AND BUCKLE.

LINE 2. DELETE "RIGHT SIDE" AND SUBSTITUTE

"LEFT SIDE".

PAGE 2, PARAGRAPH 3.1.2, BELT LOOP PLACEMENT.

LINE 5. DELETE THE LINE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING: "THE BELT LOOP ON THE

LEFT SIDE SEAM SHALL HAVE AN UNDER LOOP FOR THE

BELT ANCHOR."

PAGE 2, PARAGRAPH 3.1.2, BELT LOOP PLACEMENT.

LINE 1, AFTER "FINISHING" DELETE "1/2" AND

SUBSTITUTE "2-1/2".

PAGE 2, PARA. 3.1.2A SHOULDER STRAPS. DELETE

PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE THE

FOLLOWING PARAGRAPH: "3.1.2A SHOULDER STRAPS.

THE OVEREDGED STRAIGHT END OF SHOULDER STRAP

SHALL BE SEWN TO THE COAT WITH A 3/16 INCH SEAM

THEN FOLD STRAP TO THE FINISHED POSITION AND TOP

STITCH 1/4 INCH FROM THE FOLDED EDGE. THE

FINISHED SHOULDER STRAPS SHALL BE CENTERED ALONG

THE SHOULDER SEAM AND THE POINTED END SHALL

FINISH EVEN TO 1/2 INCH FROM THE COLLAR SETTING

SEAM. THE SHOULDER STRAPS SHALL FINISH SMOOTH

AND FLAT WITHOUT DISTORTION. THE SHOULDER STRAP

TOPSTITCHING SHALL FOLLOW THE TOP STITCHING LINE

OF THE FRONT SLEEVE SEAMS."

PAGE 2, PARAGRAPH 3.1.5, REMOVABLE LINER.

LINE 1, DELETE "SET IN SLEEVES" AND

SUBSTITUTE "1/2 RAGLAND SLEEVES".

LINE 3, AFTER ACCOMMODATE A" DELETE "27"

AND SUBSTITUTE "24".

PAGE 3, PARAGRAPH 3.1.5.1 DELETE ENTIRELY

PAGE 3, PARAGRAPH 3.2.2. BUTTONHOLES. LINE 4,

AFTER "ONE ON THE LEFT FRONT" INSERT "IN

HORIZONTAL ALIGNMENT WITH TOP BUTTON ON RIGHT

FRONT" AND AFTER "ONE ON EACH LAPEL" INSERT

"AND THE CUT OPENING OF BUTTONHOLES SHALL BE

POSITIONED 3/4 INCH FROM EDGE OF COAT."

PAGE 3, PARAGRAPH 3.2.2, BUTTONHOLES. LINE 5

AFTER "SQUARE-BAR TYPE" ADD "WORKED OVER

GIMP". AT END OF THE PARAGRAPH ADD:

"THERE SHALL BE TWO 3/4 INCH CUT, SQUARE BAR

TYPE BUTTONHOLES, ONE CENTERED ON THE BELT

FASTENER 3/8 INCH FROM THE END AND ONE

CENTERED ON THE RIGHT BACK VENT 3/4 INCH

FROM THE EDGE".

PAGE 3, PARAGRAPH 3.2.3 BUTTONS.

LINE 2, DELETE "18" AND SUBSTITUTE "45"

LINE 9, DELETE "THREE" AND SUBSTITUTE "FOUR"

LINE 10 DELETE "AND" AND SUBSTITUTE ","

LINE 10 DELETE *FASTENER) AT THE END OF

THE SENTENCE ADD "AND ONE ON THE LEFT BACK

VENT TO CORRESPOND TO THE BUTTONHOLE."

PAGE 3, AFTER PARAGRAPH 3.2.3.1 BUTTONS. INSERT

NEW PARAGRAPH AS FOLLOWS:"3.2.3.1 LAPEL BUTTON

PLACEMENT. THE TOP LEFT LAPEL BUTTON SHALL

BE POSITIONED SO THAT THE RIGHT COAT FRONT LAYS

SMOOTH AND FLAT WITHOUT DISTORTION AND THE

NECK OPENING SHALL BE 2 TO 2-1/2 INCHES BETWEEN

COLLARSTAND JOINING SEAM AND COLLARSTAND JOINING

SEAM ACROSS FRONT OF COAT."

PAGE 6, PARAGRAPH 3.3.2.4, LINE 2, AFTER

"COMBED COTTON" INSERT "OR STAPLE RAYON".

LINE 9, DELETE "2.5" AND SUBSTITUTE "1.5".

PAGE 6, PARAGRAPH 3.3.3, LINE 1, DELETE "1/4"

AND SUBSTITUTE "3/8".

PAGE 8, TABLE II, DELETE "SLEEVE LINER AND

BELT AND SUBSTITUTE "SLEEVE LINER AND BACK

VENT".

DELETE "STAY BUTTONS AND SUBSTITUTE "STAY

BUTTONS AND BELT" AND UNDER "TOTAL QUANTITY"

DELETE "STAY BUTTONS AND SUBSTITUTE "STAY"

DELETE "6" AND SUBSTITUTE "7"

PAGE 8, PARAGRAPH 3.4.9 DELETE ENTIRELY AND

SUBSTITUTE: "3.4.10 SLIDE FASTENER. THE

SLIDE FASTENER FOR THE COAT AND THE REMOVABLE

LINER SHALL BE A SEPARATING, NON-REVERSIBLE,

RIGHT-HAND, LIGHT SIZE WITH AN ALUMINUM

OR BRASS CHAIN, SHORT TAB PULL. THE LENGTHS OF

THE SLIDE FASTENERS SHALL CONFORM TO THE SIZE

COAT WITH A MINIMUM LENGTH OF 70 INCHES. THE

COLOR OF THE TAPE SHALL BE A GOOD MATCH TO THE

BASIC MATERIAL AND SHALL BE 7/16 OR 9/16 INCH

WIDE. THE ENDS OF THE SLIDE FASTENER SHALL

BE EQUIDISTANT FROM THE BOTTOM EDGE OF THE COAT.

PAGE 10, PARA.3.5 LABELS, ADD NEW PARAGRAPH

"3.5.4 DSCP EXCLUSIVE LABEL. EACH COAT

SHALL HAVE THE DSCP EXCLUSIVE LABEL SEWN

TO THE RIGHT INSIDE FRONT FACING ABOVE THE

SIZE/INSTRUCTION LABELS. THE LABEL SHALL BE

APPROXIMATELY 2 INCHES WIDE AND BE SEWN

ON ALL FOUR SIDES."

PAGE 10, PARAGRAPH 3.6.1 LIST OF PATTERN PARTS,

DELETE "BACK VENT FACING" AND "POCKET FACING,

CORD" AND INSERT "NECK FACING" AND "NECK FACING,

FUSIBLE"

PAGE 11, TABLE 1V COAT FINISHED MEASURMENTS

UNDER SLEEVE LENGTH, SIZE 22 SHORT DELETE "16"

UNDER SIZE ADD "SIZES 24 26

BREAST (1/) TYPE II ONLY 55-1/2 57-1/2

BACK LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 45-1/2 45-3/4

. LONG -- --

. XLONG -- --

SLEEVE LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 17 17

. LONG -- --

. XLONG -- --

BELT LENGTH TYPE II ONLY 55 57

PAGE 12, TABLE V LINER FINISHED MEASURMENTS

UNDER SLEEVE LENGTH, SIZE 22 SHORT DELETE "15"

UNDER SIZE ADD "SIZES 24 26

BREAST (1/) TYPE II ONLY 47 49

BACK LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 35-3/4 36

. LONG -- --

. XLONG -- --

SLEEVE LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 16 16

. LONG -- --

. XLONG -- --"

PAGE 16, PARAGRAPH 7.2.2 ASTM TEST METHODS

ADD "D-256 STANDARD TEST METHOD FOR IMPACT

RESISTANCE OF PLASTICS AND ELECTRICAL INSULATING

MATERIALS".

PACKAGING AND MARKING INSRUCTIONS

TEN (10) ALL-WEATHER COATS, ONLY SIZE ONLY,

SHALL BE PACKED IN A SNUG-FITTING FIBERBOARD

SHIPPING CONTAINER CONFORMING TO ASTM-D5118,

TYPE CF, STYLE RSC, GRADE 275, VARIETY SW, CLASS

DOMESTIC WITH A DW LINER. THE DIMENSIONS OF THE

CONTAINER SHALL APPROXIIMATE 20-L X 16-W X 24-L.

METHOD OF CLOSURE SHALL BE IN ACCORDANCE WITH

ASTM-D-1974, 2A2, FIGURE 1 OR AS AN ALTERNATE

2B6 OR 3B7, FIGURE 3.

PAGE 17, FIGURE 1, REVERSE THE BELT DIRECTION TO

GO RIGHT TO LEFT, OPPOSITE OF THE FRONT CLOSURE.

PAGE 18, FIGURE 2, REVERSE THE BELT DIRECTION TO GO RIGHT TO LEFT, OPPOSITE OF THE FRONT CLOSURE.

AQL'S FOR COMMERCIAL ITEM DESCRIPTIONS

END ITEM DIMENSIONAL 2.5

VISUAL 4.0

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

INSPECTION BY ATTRIBUTES, ANSI/AQSC Z1.4

GENERAL INSPECTION LEVEL 2".

(Ref. W2851)