PGC 02850 tech data

COAT, ALL WEATHER, MAN'S PEWTER SHADE 2246

DOUBLE BREASTED FRONT WITH BELT.

ADDITIONAL INFORMATION FOR CR PD 03-08:

PATTERN DATE: 04 DECEMBER 2003

STANDARD SAMPLE FOR CLOTH, POPLIN, POLYESTER AND

COTTON (WATER REPELLENT), MARINE CORPS PEWTER

2246 CONFORMING TO A-A-50531, IS AVAILABLE ON

ROLL NO. 1208-06. THIS SAMPLE SHALL SHOW COLOR-

FASTNESS IN ACCORDANCE WITH THE TABLE BELOW.

CHARACTERISTICS REQUIREMENT TEST METHOD

LAUNDERING (MIN) EQUAL TO

STANDARD AATCC 61 3A

AFTER 3 CYCLES GRADE 4 AATCC 61 3A

PERSPIRATION (MIN) GRADE 4 AATCC 15 1/

CROCKING (MIN) GRADE 2.5 AATCC 8

LIGHT (MIN) GRADE 4 AATCC 16 OPT A

INTERIM CHANGES TO PD-03-08:

PAGE 11, TABLE IV -COAT FINISHED MEASUREMENTS,

DELETE TABLE IV & INSERT NEW TABLE AS FOLLOWS:

TABLE IV COAT FINISHED MEASUREMENTS

SIZE

. 30------32------34------36------38------40

ALL LENGTHS CHEST (1/) TOLERANCE +/- 3/4

. 39 41 43 45 47 49

SIZE

. 42------44------46------48------50------52

ALL LENGTHS CHEST (CONTINUED)

. 51 53 55 57 59 61

SIZE

. 30------32------34------36------38------40

BACK LENGTH (2/) TOLERENCE +/- 1/2

XS-- 40-3/4 41 41-1/4 41-1/2 41-3/4

S 42-1/2 42-3/4 43 43-1/4 43-1/2 43-3/4 R 44-1/2 44-3/4 45 45-1/4 45-1/2 45-3/4 L -- 46-3/4 47 47-1/4 47-1/2 47-3/4

XL-- -- 49-1/2 49-3/4 50 50-1/4

SIZE

. 42------44------46------48------50------52

BACK LENGTH (CONTINUED)

XS42 -- -- -- -- --

S 44 44-1/4 44-1/2 44-3/4 45 45-1/4 R 46 46-1/4 46-1/2 46-3/4 47 47-1/4 L 48 48-1/4 48-1/2 48-3/4 49 49-1/4

XL50-1/2 50-3/4 51 51-1/4 -- --

SIZE

. 30------32------34------36------38------40

SLEEVE LENGTH (/3) TOLERANCE +/- 1/2

XS-- 16 16 16 16 16

S 17 17 17 17 17 17 R 18 18 18 18 18 18 L -- 19 19 19 19 19

XL-- 20-1/2 20-1/2 20-1/2 20-1/2 20-1/2

SIZE

. 42------44------46------48------50------52

SLEEVE LENGTH (CONTINUED)

XS16 -- -- -- -- --

S 17 17 17 17 17 17 R 18 18 18 18 18 18 L 19 19 19 19 19 19

XL20-1/2 20-1/2 20-1/2 20-1/2 -- --

SIZE

. 30------32------34------36------38------40

BELT LENGTH (/4) TOLERANCE +/-3/4

. 40 42 44 46 48 50

SIZE

. 42------44------46------48------50------52

BELT LENGTH (CONTINUED)

. 52 54 56 58 60 62

ADDITIONAL INTERIM CHANGES TO CR/PD 03-08

PAGE 1, SCHEDULE OF SIZES, DELETE ENTIRELY AND

SUBSTITUTE THE FOLLOWING:

"XSHORT SHORT REG LONG XLONG

--- 30 30 --- --- 32 32 32 32 --- 34 34 34 34 34 36 36 36 36 36 38 38 38 38 38 40 40 40 40 40 42 42 42 42 42 --- 44 44 44 44 --- 46 46 46 46 --- 48 48 48 48 --- 50 50 50 --- --- 52 52 52 ---

PAGE 2 PARAGRAPH 3.1 DESCRIPTION, LINE 5

AFTER "5" ADD "THE MATERIAL FOR THE

SLEEVE LINING SHALL BE TAFFETA AS SPEC-

IFIED IN PARAGRAPH 3.3.2.2.)

LINE 5, DELETE "1/4" AND SUBSTITUTE "3/8".

PAGE 2, PARAGRAPH 3.1.2, BELT LOOP PLACEMENT

LINE 1, AFTER "FINISHING" DELETE "1/2" AND

SUBSTITUTE "2-1/2".

PAGE 2, PARA. 3.1.2a SHOULDER STRAPS, DELETE

PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE THE

FOLLOWING PARAGRAPH: "3.1.2a SHOULDER STRAPS.

THE OVEREDGED STRAIGHT END OF SHOULDER STRAP

SHALL BE SEWN TO THE COAT WITH A 3/16 INCH SEAM,

THEN FOLD STRAP TO THE FINISHED POSITION AND TOP

STITCH 1/4 INCH FROM THE FOLDED EDGE. THE

FINISHED SHOULDER STRAPS SHALL BE CENTERED ALONG

THE SHOULDER SEAM AND THE POINTED END SHALL

FINISH EVEN TO 1/2 INCH FROM THE COLLAR SETTING

SEAM. THE SHOULDER STRAPS SHALL FINISH SMOOTH

AND FLAT WITHOUT DISTORTION. THE SHOULDER STRAP

TOPSTITCHING SHALL FOLLOW THE TOP STITCHING LINE

OF THE FRONT SLEEVE SEAMS."

PAGE 2, PARAGRAPH 3.1.5, REMOVABLE LINER,

LINE 1, DELETE "SET IN SLEEVES" AND

SUBSTITUTE "1/2 RAGLAND SLEEVES".

LINE 3, AFTER ACCOMODATE A" DELETE "27"

AND SUBSTITUTE "24"

PAGE 2, PARAGRAPH 3.1.5.1 DELETE ENTIRELY

PAGE 3, PARAGRAPH 3.2.2. BUTTONHOLES, LINE 4,

AFTER "ONE ON THE RIGHT FRONT" INSERT "IN

HORIZONTAL ALIGNMENT WITH TOP BUTTON ON RIGHT

FRONT" AND AFTER "ONE ON EACH LAPEL" INSERT

"AND THE CUT OPENING OF BUTTONHOLES SHALL BE

POSITIONED 3/4 INCH FROM EDGE OF COAT."

PAGE 3, PARAGRAPH 3.2.2, BUTTONHOLES, LINE 5

AFTER "SQUARE-BAR TYPE" ADD "WORKED OVER

GIMP". AT END OF THE PARAGRAPH ADD:

"THERE SHALL BE TWO 3/4 INCH CUT, SQUARE BAR

TYPE BUTTONHOLES, ONE CENTERED ON THE BELT

FASTENER 3/8 INCH FROM THE END AND ONE

CENTERED ON THE RIGHT BACK VENT AS PER

MARK ON PATTERN

THE LAPEL BUTTONHOLES SHALL BE 3/4 INCH FROM

THE EDGE AND 1-1/2 INCHES DOWN FROM THE TOP

PAGE 3, PARAGRAPH 3.2.3 BUTTONS

LINE 2, DELETE "18" AND SUBSTITUTE "45"

LINE 9 DELETE "THREE" AND SUBTITUTE "FOUR"

LINE 10 DELETE "AND" AND SUBSTITUTE ","

LINE 10 DELETE "FASTENER" AT THE END OF

THE SENTENCE ADD "AND ONE THE LEFT BACK

VENT TO CORRESPOND TO THE BUTTONHOLE."

PAGE 3, AFTER PARAGRAPH 3.2.3 BUTTONS, INSERT

NEW PARAGRAPH AS FOLLOWS:"3.2.3.1 LAPEL BUTTON

PLACEMENT. THE TOP RIGHT LAPEL BUTTON SHALL

BE POSITIONED SO THAT THE LEFT COAT FRONT LAYS

SMOOTH AND FLAT WITHOUT DISTORTION AND THE

NECK OPENING SHALL BE 2 TO 2-1/2 INCHES BETWEEN

COLLARSTAND JOINING SEAM AND COLLARSTAND JOINING

SEAM ACROSS FRONT OF COAT."

PAGE 6, PARAGRAPH 3.3.2.4, LINE 2 AFTER

"COMBED COTTON" INSERT "OR STAPLE RAYON".

LINE 9: DELETE "2.5" AND SUBSTITUTE "1.5"

PAGE 6, PARAGRAPH 3.3.3, LINE 1 DELETE "1/4"

AND SUBSTITUTE "3/8".

PAGE 8, TABLE II, DELETE "SLEEVE LINER AND

BELT" AND SUBSTITUTE "SLEEVE LINER AND BACK

VENT".

DELETE "STAY BUTTONS AND SUBSTITUTE "STAY

BUTTONS AND BELT) AND UNDER "TOTAL QUANTITY"

DELETE "6" AND SUBSTITUTE "7"

PAGE 8, PARAGRAPH 3.4.9 DELETE ENTIRELY AND

SUBSITUTE: "3.4.10 SLIDE FASTENER. THE

SLIDE FASTENER FOR THE COAT AND THE REMOV-

ABLE LINER SHALL BE A SEPARATING, NON-REVER-

SIBLE, RIGHT-HAND, LIGHT SIZE WITH AN ALUMINUM

OR BRASS CHAIN, SHORT TAB PULL. THE LENGTHS OF

THE SLIDE FASTENERS SHALL CONFORM TO THE SIZE

COAT WITH A MINIMUM LENGTH.OF 70 INCHES. THE

COLOR OF THE TAPE SHALL BE A GOOD MATCH TO THE

BASIC MATERIAL AND SHALL BE 7/16 OR 9/16 INCH

WIDE. THE ENDS OF THE SLIDE FASTENER SHALL

BE EQUIDISTANT FROM THE BOTTOME EDGE OF COAT.

PAGE 10, PARA.3.5 LABELS, ADD NEW PARAGRAPH

"3.5.4 DSCP EXCLUSIVE LABEL: EACH COAT

SHALL HAVE THE DSCP EXCLUSIVE LABEL SEWN

TO THE RIGHT INSIDE FRONT FACING ABOVE THE

SIZE/INSTRUCTION LABELS.THE LABEL SHALL

APPROXIMATELY 2 INCHES WIDE AND BE SEWN

ON ALL FOUR SIDES."

PAGE 10, TABLE III, LIST OF PETTERN PARTS, DELETE "BACK VENT FACING" AND "POCKET FACING, CORD" AND INSERT "NECK FACING" AND "NECK FACING, FUSIBLE".

PAGE 12, TABLE V - LINER FINISHED MEASUREMENTS,

DELETE TABLE V AND INSERT NEW TABLE AS FOLLOWS:

TABLE V LINER FINISHED MEASUREMENTS

ALL LENGTHS CHEST (1/) TOLERANCE +/- 3/4

SIZE

. 30------32------34------36------38------40 . 31 33 35 37 39 41

ALL LENGTHS CHEST (CONTINUED)

SIZE

. 42------44------46------48------50------52 . 43 45 47 49 51 53

. BACK LENGTH (2/) TOLERENCE +/- 1/2

SIZE

. 30------32------34------36------38------40

XS-- 33 33-1/4 33-1/2 33-3/4 34

S 34-3/4 35 35-1/4 35-1/2 35-3/4 36 R 36-3/4 37 37-1/4 37-1/2 37-3/4 38 L - 39 39-1/4 39-1/2 39-3/4 40

XL-- -- 41-3/4 42 42-1/4 42-1/2

. BACK LENGTH (CONTINUED)

SIZE

. 42------44------46------48------50------52

XS34-1/4 -- -- -- -- --

S 36-1/4 36-1/2 36-3/4 37 37-1/4 37-1/2 R 38-1/4 38-1/2 38-3/4 39 39-1/4 39-1/2 L 40-1/4 40-1/2 40-3/4 41 41-1/4 41 1/2

XL42-3/4 43 43-1/4 43-1/2 -- --

SLEEVE LENGTH (/3) TOLERANCE +/- 1/2

SIZE

. 30------32------34------36------38------40

XS-- 14-1/2 14-1/2 14-1/2 14-1/2 14-1/2

S 15-1/2 15-1/2 15-1/2 15-1/2 15-1/2 15-1/2 R 16-1/2 16-1/2 16-1/2 16-1/2 16-1/2 16-1/2 L -- 17-1/2 17-1/2 17-1/2 17-1/2 17-1/2

XL-- -- 18-1/2 18-1/2 18-1/2 18-1/2

SLEEVE LENGTH (CONTINUED)

SIZE

. 42------44------46------48------50------52

XS14-1/2 -- -- -- -- --

S 15-1/2 15-1/2 15-1/2 15-1/2 15-1/2 15-1/2 R 16-1/2 16-1/2 16-1/2 16-1/2 16-1/2 16-1/2 L 17-1/2 17-1/2 17-1/2 17-1/2 17-1/2 17-1/2

XL18-1/2 18-1/2 18-1/2 18-1/2 -- --

PAGE 16, PARAGRAPH 7.2.2 ASTM TEST METHODS

ADD "D-256 STANDARD TEST METHOD FOR IMPACT RE-

SISTANCE OF PLASTICS AND ELECTRICAL INSULATING

MATERIALS".

PACKAGING AND MARKING INSTRUCTIONS:

TEN (10) ALL WEATHER COATS ONE SIZE ONLY SHALL

BE PACKED IN A SNUG FITTING FIBERBOARD SHIPPING

CONTAINER CONFORMING TO ASTM-D5118, TYPE CF,

STYLE RSC,GRADE 275, VARIETY SW, CLASS DOMESTIC

WITH A DW LINER. THE DIMENSIONS OF THE CONTAINER

SHALL APPROXIMATE 20-L X 16-W X 24-L. METHOD OF

CLOSURE SHALL BE IN ACCORDANCE WITH ASTM-D-1974,

2A2, FIGURE 1 OR AS AND ALTERNATE 2B6 OR 2B7-

FIGURE 3.

AQL'S FOR COMMERCIAL ITEM DESCRIPTIONS

END ITEM DIMENSIONAL 2.5

VISUAL 4.0

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

USE OF SAMPLING PROCEDURES AND TABLES FOR

INSPECTION BY ATTRIBUTES, ANSI/AQSC Z1.4,

GENERAL INSPECTION LEVEL 2".

(Ref. W2850)