PID AND PACK--SPE7LX20R0086.pdf

PID ANDPACK--SPE7MX20D0086.pdf[2/25/2020 10:59:16 AM]

*** LTC PID Packaging Consolidated Text *** PLEASE SEE GLOSSARY AT THE END OF THE DOCUMENT FOR FULL TEXT OF THE ITEM DESCRIPTION

AND PACKAGING REFERENCE NUMBERS CALLED OUT FOR EACH NSN.

NSN:015022579

BATTERY POWER SUPPLY

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RD002

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RQ002

REFERENCE NUMBER:RQ009

REFERENCE NUMBER:RQ011

REFERENCE NUMBER:RT001

REFERENCE NUMBER:ZDISO

REFERENCE NUMBER:CS120

REFERENCE NUMBER:ZD017

CRITICAL APPLICATION ITEM

C. E. NIEHOFF & CO. 76761 P/N 12422851-001

C. E. NIEHOFF & CO. 76761 P/N N2003-1

IAW BASIC DRAWING NR 19207 12422851

REVISION NR D DTD 10/01/2012

PART PIECE NUMBER: 12422851-001

IAW REFERENCE DRAWING NR 19207 12422851-001

REVISION NR DTD 12/02/2019

PART PIECE NUMBER:

PREP FOR DELIVERY

LINE ITEM 00001 TYPE OF COVERAGE: DLA DIRECT, CONUS

PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999

QUP:001 PRES MTHD:31 CLNG/DRY:1 PRESV MAT:00

WRAP MAT:00 CUSH/DUNN MAT:NA CUSH/DUNN THKNESS:D

UNIT CONT:E5 OPI:M

INTRMDTE CONT:D3 INTRMDTE CONT QTY:AAA

PACK CODE = E: PACKING LEVEL = B:

MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.

SPECIAL MARKING CODE:00 -00 No special marking

PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008

GLOSSARY

PACKAGING TEXT

THE FOLLOWING PARAGRAPH APPLIES TO ALL PACKAGING CALLED OUT IN THIS DOCUMENT:

ITEM DESCRIPTION TEXT

REFERENCE NUMBER RP001

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

REFERENCE NUMBER RD002

RD002, COVERED DEFENSE INFORMATION APPLIES

REFERENCE NUMBER RA001

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB

AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

REFERENCE NUMBER RQ002

RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL

REQUEST FOR VARIANCE (DEVIATION OR WAIVER)

REFERENCE NUMBER RQ009

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

REFERENCE NUMBER RQ011

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

REFERENCE NUMBER RT001

RT001: MEASURING AND TEST EQUIPMENT

REFERENCE NUMBER ZDISO

FAR CLAUSE 52.246-11 APPLIES. THE CONTRACTOR SHALL BE IN COMPLIANCE

WITH THE FULL REQUIREMENTS OF THE INTERNATIONAL ORGANIZATION FOR

STANDARDIZATION (ISO) 9001 STANDARD AT THE TIME OF CONTRACT ACCEPTANCE

OR CONTRACT MODIFICATION DATE.

1. The minimum Higher Level Contract Quality Requirements for manufacturers for DLA ISO 9001:2015. MIL-I-45208 and MIL-Q-9858 are obsolete and no longer acceptable when higher level quality is required.

2. Higher-Level Contract Quality Requirement for Non-Manufacturers. If a non-manufacturer is supplying the material, the non-manufacturer shall:

(i) Furnish items produced at a manufacturing facility conforming to the higher-level contract quality requirement for manufacturers as specified in paragraph 1; and

(ii) Maintain and provide documented evidence that material furnished under this contract was produced at a manufacturing facility conforming to the specified higher-level contract quality requirement and that the material meets all requirements. At a minimum, the documented evidence shall be sufficient to establish the identity of the product and its manufacturing source; and include the basic item description, the item(s) part number and/or national stock number, the item(s) manufacturing source , the manufacturing source#s commercial and government entity code (e.g. CAGE code), and clear identification of the name and location of supply chain intermediaries from the manufacturer to the direct source of the product for the offeror/contractor, to the item(s) acceptance by the Government. It should also include, where available, the manufacturer's batch identification for the part(s), such as date codes, lot codes, or serial numbers.

(iii) Maintain documentation of the Non-Manufacturers# quality assurance program; receiving/verification processes; records management system;

procurement system; inventory control system; testing results; and any other records associated with the material being provided.

(End of TQ Requirement)

REFERENCE NUMBER CS120

NOTE: THE CITED DRAWING IS A SOURCE CONTROLLED

DRAWING AND AS OF THE DATE OF THIS SOLICITATION

ONLY THE SOURCE(S) CITED ON THE DRAWING HAVE

BEEN APPROVED. EVEN THOUGH SOURCES AND APPROVED

PART NUMBERS ARE PROVIDED, THE ITEMS

FURNISHED MUST MEET THE REQUIREMENTS OF THE

CITED DRAWING. OFFERORS WHO ARE INTERESTED IN

QUALIFYING THEIR PRODUCT FOR PURPOSE OF FUTURE

ACQUISITION MUST CONTACT THE COGNIZANT DESIGN

ACTIVITY SPECIFIED ON THE SOURCE CONTROLLED

DRAWING.

ALSO, MAY INCLUDE ADDITIONAL APPROVED SOURCES

THAT HAVE NOT BEEN REFLECTED ON THE DRAWING AT

THIS TIME.

REFERENCE NUMBER ZD017

In addition to MIL-STD-129 markings, each MRAP palletized shipment shall include two, 10 inch by 10 inch fluorescent yellow sticker/sign/placard with the letters MRAP in 2 inch bold black letters and applied to one side and one panel of palletized load. For better visibility, place the MRAP sticker/sign/placard on the outside of the multiwall container(s) or the pallet, not under any shrink-wrap. The stickers are to be placed high on each side of each container, so they are visible at eye level.

This sticker/sign/placard is required to expedite the receipt and inspection of these shipments. This requirement is only applicable for shipments directed to DDC depots and direct vendor deliveries to CCPs;

and does not apply to direct vendor deliveries to the customer.

ACCEPTABLE DEVIATIONS: Contractor is authorized to make adjustments to actual sticker size and font size when shipping containers are not large enough to adequately display all required MIL-STD-129 markings along with the standard size (as cited above).

OEM MRAP STICKERS: Each OEM has a designated background color in lieu of the standard yellow background MRAP sticker in an effort to apply Lean

Six Sigma principles and concepts to packaging, storage, and transport of MRAP material to theater. The following are the official designations (background color # text required):

GREEN # MRAP BAE (TX)

TEAL # MRAP OSHKOSH

PURPLE # MRAP BAE (PA)

ORANGE # MRAP FPII

BLUE # MRAP NAVISTAR

PINK # MRAP GDLS

NOTE: If MRAP stickers are missing or OEM is exhausting yellow background stickers, no quality notification shall be submitted to Contract Administrating Activity.