PID (Drag Link).docx

*** LTC PID Packaging Consolidated Text ***

PLEASE SEE GLOSSARY AT THE END OF THE DOCUMENT FOR FULL TEXT OF THE ITEM DESCRIPTION

AND PACKAGING REFERENCE NUMBERS CALLED OUT FOR EACH NSN.

NSN: 2530013773127

DRAG LINK, STEERING

REFERENCE NUMBER:RQ002

REFERENCE NUMBER:CVC01

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RQ001

REFERENCE NUMBER:RQ009

REFERENCE NUMBER:RQ011

REFERENCE NUMBER:RQ016

REFERENCE NUMBER:CA070

REFERENCE NUMBER:CS187

REFERENCE NUMBER:CQ026

REFERENCE NUMBER:A1166

REFERENCE NUMBER:A0009

CRITICAL APPLICATION ITEM

IAW BASIC DRAWING NR 19207 12418103

REVISION NR D DTD 02/28/2011

PART PIECE NUMBER: 12418103-002

IAW REFERENCE DRAWING NR 19207 12420325

REVISION NR J DTD 04/08/2019

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12418103-002

REVISION NR DTD 05/07/2019

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12418103-002

REVISION NR B DTD 06/30/2010

PART PIECE NUMBER:

PREP FOR DELIVERY

LINE ITEM 00001 TYPE OF COVERAGE: DLA DIRECT, CONUS

PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999

QUP:001 PRES MTHD:ZZ CLNG/DRY:Z PRESV MAT:ZZ

WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:Z

UNIT CONT:ZZ OPI:A

PACK CODE:U

MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.

SPECIAL MARKING CODE:ZZ -ZZ Special Requirements

PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008

PRESERVATION, PACKAGING, AND PACKING SHALL BE IN ACCORDANCE WITH SPECIAL PACKAGING INSTRUCTION (SPI) AK13773127, REVISIOJN B, DATED 06/30/2010.

REFERENCE NUMBER:ZD017

REFERENCE NUMBER:IP025

If Product First Article Testing (FAT) is required and a Packaging FAT is included in the Special Packaging Instruction or Drawing, the Packaging FAT requirement is invoked. If there is no Product FAT, no Packaging FAT is required.

GLOSSARY

PACKAGING TEXT

THE FOLLOWING PARAGRAPH APPLIES TO ALL PACKAGING CALLED OUT IN THIS DOCUMENT:

ITEM DESCRIPTION TEXT

REFERENCE NUMBER RQ002

RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER)

REFERENCE NUMBER CVC01

"VENDOR ITEM CONTROL DRAWING"

REFERENCE NUMBER RP001

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

REFERENCE NUMBER RA001

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

REFERENCE NUMBER RQ001

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS)

REFERENCE NUMBER RQ009

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

REFERENCE NUMBER RQ011

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

REFERENCE NUMBER RQ016

RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS LISTS (QML). THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR QUALIFIED MANUFACTURERS LIST (QML). QUALIFICATION REQUIREMENTS IN PROCUREMENT NOTE H02 "COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED MANUFACTURERS LIST (QML)" APPLY.

REFERENCE NUMBER CA070

FULL AND OPEN COMPETITION APPLY

REFERENCE NUMBER CS187

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS.

REFERENCE NUMBER CQ026

ANY ITEM PREVIOUSLY TESTED BY A VENDOR IN ACCORDANCE WITH *** QUALIFICATION*** REQUIREMENTS (FOR EXAMPLE: FAT, HIGH SHOCK AND/OR VIBRATION TEST), STATED ON DWG, SPECIFICATION, OR STANDARD MAY NOT REQUIRE FURTHER TESTING BY THE SAME VENDOR EXCEPT FOR A LATER CHANGE IN DESIGN, MANUFACTURING PROCEDURES, OR TESTING REQUIREMENTS. A CERTIFICATION OF CONFORMANCE WITH PREVIOUS TEST RESULTS ATTESTING APPLICABILITY SHALL BE SUBMITTED FOR ITEMS PREVIOUSLY TESTED.

REFERENCE NUMBER A1166

RESTRICTION ON THE ACQUISITION OF BALL AND ROLLER BEARINGS (JUN 2011) An award can only be made for a bearing manufactured in the United States, its outlying areas, or Canada and the cost of the bearing components (bearing element, retainer, inner race, outer race) manufactured in the United States, its outlying areas, or Canada must exceed 50% of the total cost of the bearing components of that ball or roller bearing. See DFARS Clause 252.225-7016, RESTRICTION ON ACQUISITION OF BALL AND ROLLER BEARINGS (Jun 2011). A Contractor's declaration on the domestic/foreign nature of the material being offered is required. To obtain a copy of the "Contractors Declaration Form" please visit the DLA Aviation Foreign Bearing Website at http://www.dla.mil/Aviation/Business/IndustryResources/DLAResourcesforSuppliers/ ForeignBearingWaiver.aspx Please have the completed form ready for submission upon request by the Acquisition Specialist. Failure to provide this information may result in your quote not being considered for award. In the event no offered bearings meet this sourcing requirement, this solicitation may be cancelled and a waiver may be requested by the procurement activity. Upon receipt of an approved waiver, the requirement may be resolicited. See FAR 225.7009-4, Waiver, Restriction on Ball and Roller Bearings (DEC 2010).

REFERENCE NUMBER A0009

ALL CLASS 3A AND 3B THREADS SHALL BE GAGED I/A/W CATEGORY 1 PER SAE AS8879 OR "SAFETY CRITICAL THREADS" PER MIL-S-7742 UNLESS OTHERWISE SPECIFIED. THE ABOVE EXCLUDES SELF-LOCKING NUTS AND INTERNAL THREADS SMALLER THAN .190 DIA. AND EXTERNAL THREADS SMALLER THAN .138 DIA.

REFERENCE NUMBER ZD017

In addition to MIL-STD-129 markings, each MRAP palletized shipment shall include two, 10 inch by 10 inch fluorescent yellow sticker/sign/placard with the letters MRAP in 2 inch bold black letters and applied to one side and one panel of palletized load. For better visibility, place the MRAP sticker/sign/placard on the outside of the multiwall container(s) or the pallet, not under any shrink-wrap. The stickers are to be placed high on each side of each container, so they are visible at eye level. This sticker/sign/placard is required to expedite the receipt and inspection of these shipments. This requirement is only applicable for shipments directed to DDC depots and direct vendor deliveries to CCPs; and does not apply to direct vendor deliveries to the customer.

ACCEPTABLE DEVIATIONS: Contractor is authorized to make adjustments to actual sticker size and font size when shipping containers are not large enough to adequately display all required MIL-STD-129 markings along with the standard size (as cited above).

OEM MRAP STICKERS: Each OEM has a designated background color in lieu of the standard yellow background MRAP sticker in an effort to apply Lean Six Sigma principles and concepts to packaging, storage, and transport of MRAP material to theater. The following are the official designations (background color # text required):

GREEN # MRAP BAE (TX)

TEAL # MRAP OSHKOSH

PURPLE # MRAP BAE (PA)

ORANGE # MRAP FPII

BLUE # MRAP NAVISTAR

PINK # MRAP GDLS

NOTE: If MRAP stickers are missing or OEM is exhausting yellow background stickers, no quality notification shall be submitted to Contract Administrating Activity.

REFERENCE NUMBER IP025

IP025: PACKAGING, MARKING, AND SHIPPING OF HAZARDOUS MATERIALS