Attachment_1-PID.pdf

Solicitation SPE7LX-18-R-0104

Attachment 1-PID

*** LTC PID Packaging Consolidated Text *** PLEASE SEE GLOSSARY AT THE END OF THE DOCUMENT FOR FULL TEXT OF THE ITEM DESCRIPTION

AND PACKAGING REFERENCE NUMBERS CALLED OUT FOR EACH NSN.

NSN:014912671

PULLEY, GROOVE.

NOTE: LITENS AUTOMOTIVE PARTNERSHIP CAGE CODE IS L8732 IN LIEU OF 001Y9

AS CITED ON DRAWING 12469483.

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RQ009

REFERENCE NUMBER:RQ011

REFERENCE NUMBER:CS001

REFERENCE NUMBER:CS120

CRITICAL APPLICATION ITEM

AM General LLC 34623 P/N 12469483

LITENS AUTOMOTIVE PARTNERSHIP DBA L8732 P/N 600634

IAW BASIC DRAWING NR 19207 12469483

REVISION NR A DTD 04/30/2009

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12469483

REVISION NR DTD 03/28/2018

PART PIECE NUMBER:

PREP FOR DELIVERY

LINE ITEM 00001 TYPE OF COVERAGE: DLA DIRECT, CONUS

PKGING DATA-QUP:001

SHALL BE PACKAGED IN ACCORDANCE WITH ASTM D 3951.

GLOSSARY

PACKAGING TEXT

THE FOLLOWING PARAGRAPH APPLIES TO ALL PACKAGING CALLED OUT IN THIS DOCUMENT:

Markings Paragraph

When ASTM D3951, Commercial Packaging is specified, the following apply:

•,,All Section “D” Packaging and Marking Clauses take precedence over

ASTM D3951.

•,,In addition to requirements in MIL-STD-129, when Commercial Packaging is used, the Method of Preservation for all MIL-STD-129 marking and labeling shall b •,,The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) as specified in the contract take precedence over QUP in ASTM D3951.

ITEM DESCRIPTION TEXT

REFERENCE NUMBER RA001

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB

AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR

SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

REFERENCE NUMBER RP001

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

REFERENCE NUMBER RQ009

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

REFERENCE NUMBER RQ011

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

REFERENCE NUMBER CS001

THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO

EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA AND

ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED THROUGH

JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS OF

STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL

AGREEMENTS.

TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, MILITARY CRITICAL

TECHNICAL DATA AGREEMENT, FORM IS AVAILABLE AT THE WORLD WIDE WEB

ADDRESS:

https://public.logisticsinformationservice.dla.mil/PublicHome/jcp/defaul t.aspx

OR BY WRITING TO:

DLA LOGISTICS INFORMATION SERVICE

FEDERAL CENTER

74 WASHINGTON AVE., NORTH

BATTLE CREEK, MI 49037-3084

TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A

CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT,

DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY

THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN

EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 EXEMPTIONS OF

GENERAL APPLICABILITY, AND/OR EAR PART 740 ARE APPLICABLE.

NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL DATA ARE

REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN APPLICABLE AGREEMENT

OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO RECEIVE A COPY OF THE

EXPORT CONTROLLED TECHNICAL DATA.

NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO

THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA

UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY

PERMITTED BY DODD 5230.25.

REFERENCE NUMBER CS120

NOTE: THE CITED DRAWING IS A SOURCE CONTROLLED

DRAWING AND AS OF THE DATE OF THIS SOLICITATION

ONLY THE SOURCE(S) CITED ON THE DRAWING HAVE

BEEN APPROVED. EVEN THOUGH SOURCES AND APPROVED

PART NUMBERS ARE PROVIDED, THE ITEMS

FURNISHED MUST MEET THE REQUIREMENTS OF THE

CITED DRAWING. OFFERORS WHO ARE INTERESTED IN

QUALIFYING THEIR PRODUCT FOR PURPOSE OF FUTURE

ACQUISITION MUST CONTACT THE COGNIZANT DESIGN

ACTIVITY SPECIFIED ON THE SOURCE CONTROLLED

DRAWING.

ALSO, MAY INCLUDE ADDITIONAL APPROVED SOURCES

THAT HAVE NOT BEEN REFLECTED ON THE DRAWING AT

THIS TIME.