MC Men AWC Tech data CRPD 03-08 posted March 31.docx

INTERIM CHANGES| CR PD 03-08 MARINE CORPS 3/31/2022

COAT, ALL-WEATHER, MEN'S

ADDITIONAL INFORMATION FOR CR PD 03-08:

COAT, ALL WEATHER, MEN'S, SHALL BE MADE IN ACCORDANCE WITH TYPE I – WITH RIGHT AND LEFT GUN PATCHES (MARINE CORPS) OF CR/PD 03-08

PATTERN DATE: 04 DEC 2003

SAMPLE SIZE: 40R

PGC:02850

STANDARD SAMPLE FOR CLOTH, POPLIN, POLYESTER AND

COTTON (WATER REPELLENT), MARINE CORPS PEWTER 2246 CONFORMING TO A-A-50531A, AND APPLICABLE FOR SHADE, FINISH & COLORFASTNESS ON ROLL NO. 3897.

CHARACTERISTICS REQUIREMENT TEST METHOD

LAUNDERING (MIN) EQUAL TO

STANDARD AATCC 61 3A

AFTER 3 CYCLES GRADE 4 AATCC 61 3A

PERSPIRATION (MIN) GRADE 4 AATCC 15 1/

CROCKING (MIN) GRADE 2.5 AATCC 8

LIGHT (MIN) GRADE 4 AATCC 16 OPT A

INTERIM CHANGES TO PD-03-08:

PAGE 11, TABLE IV -COAT FINISHED MEASUREMENTS,

DELETE TABLE IV & INSERT NEW TABLE AS FOLLOWS:

TABLE IV COAT FINISHED MEASUREMENTS

SIZE

. 30------32------34------36------38------40

ALL LENGTHS CHEST (1/) TOLERANCE +/- 3/4

. 39 41 43 45 47 49

SIZE

. 42------44------46------48------50------52

ALL LENGTHS CHEST (CONTINUED)

. 51 53 55 57 59 61

SIZE

. 30------32------34------36------38------40

BACK LENGTH (2/) TOLERENCE +/- 1/2

XS-- 40-3/4 41 41-1/4 41-1/2 41-3/4

S 42-1/2 42-3/4 43 43-1/4 43-1/2 43-3/4 R 44-1/2 44-3/4 45 45-1/4 45-1/2 45-3/4 L -- 46-3/4 47 47-1/4 47-1/2 47-3/4

XL-- -- 49-1/2 49-3/4 50 50-1/4

SIZE

. 42------44------46------48------50------52

BACK LENGTH (CONTINUED)

XS42 -- -- -- -- --

S 44 44-1/4 44-1/2 44-3/4 45 45-1/4 R 46 46-1/4 46-1/2 46-3/4 47 47-1/4 L 48 48-1/4 48-1/2 48-3/4 49 49-1/4

XL50-1/2 50-3/4 51 51-1/4 -- --

SIZE

. 30------32------34------36------38------40

SLEEVE LENGTH (/3) TOLERANCE +/- 1/2

XS-- 16 16 16 16 16

S 17 17 17 17 17 17 R 18 18 18 18 18 18 L -- 19 19 19 19 19

XL-- 20-1/2 20-1/2 20-1/2 20-1/2 20-1/2

SIZE

. 42------44------46------48------50------52

SLEEVE LENGTH (CONTINUED)

XS16 -- -- -- -- --

S 17 17 17 17 17 17 R 18 18 18 18 18 18 L 19 19 19 19 19 19

XL20-1/2 20-1/2 20-1/2 20-1/2 -- --

SIZE

. 30------32------34------36------38------40

BELT LENGTH (/4) TOLERANCE +/-3/4

. 40 42 44 46 48 50

SIZE

. 42------44------46------48------50------52

BELT LENGTH (CONTINUED)

. 52 54 56 58 60 62

ADDITIONAL INTERIM CHANGES TO CR/PD 03-08

PAGE 1, SHEDULE OF SIZES, DELETE ENTIRELY AND

SUBSTITUTE THE FOLLOWING:

"XSHORT SHORT REG LONG XLONG

--- 30 30 --- --- 32 32 32 32 --- 34 34 34 34 34 36 36 36 36 36 38 38 38 38 38 40 40 40 40 40 42 42 42 42 42 --- 44 44 44 44 --- 46 46 46 46 --- 48 48 48 48 --- 50 50 50 --- --- 52 52 52 ---

PAGE 2 PARAGRAPH 3.1 DESCRIPTION, LINE 5

AFTER "5" ADD "THE MATERIAL FOR THE

SLEEVE LINING SHALL BE TAFFETA AS SPEC-

IFIED IN PARAGRAPH 3.3.2.2.)

LINE 5, DELETE "1/4" AND SUBSTITUTE "3/8".

PAGE 2, PARAGRAPH 3.1.2, BELT LOOP PLACEMENT

LINE 1, AFTER "FINISHING" DELETE "1/2" AND

SUBSTITUTE "2-1/2".

PAGE 2, PARA. 3.1.2a SHOULDER STRAPS, DELETE

PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE THE

FOLLOWING PARAGRAPH: "3.1.2a SHOULDER STRAPS.

THE OVEREDGED STRAIGHT END OF SHOULDER STRAP

SHALL BE SEWN TO THE COAT WITH A 3/16 INCH SEAM,

THEN FOLD STRAP TO THE FINISHED POSITION AND TOP

STITCH 1/4 INCH FROM THE FOLDED EDGE. THE

FINISHED SHOULDER STRAPS SHALL BE CENTERED ALONG

THE SHOULDER SEAM AND THE POINTED END SHALL

FINISH EVEN TO 1/2 INCH FROM THE COLLAR SETTING

SEAM. THE SHOULDER STRAPS SHALL FINISH SMOOTH

AND FLAT WITHOUT DISTORTION. THE SHOULDER STRAP

TOPSTITCHING SHALL FOLLOW THE TOP STITCHING LINE

OF THE FRONT SLEEVE SEAMS."

PAGE 2, PARAGRAPH 3.1.5, REMOVABLE LINER,

LINE 1, DELETE "SET IN SLEEVES" AND

SUBSTITUTE "1/2 RAGLAN SLEEVES".

LINE 3, AFTER "ACCOMODATE A" DELETE "27"

AND SUBSTITUTE "24"

PAGE 2, PARAGRAPH 3.1.5.1 DELETE ENTIRELY

PAGE 3, PARAGRAPH 3.2.2. BUTTONHOLES, LINE 4,

AFTER "ONE ON THE RIGHT FRONT" INSERT "IN

HORIZONTAL ALIGNMENT WITH TOP BUTTON ON RIGHT

FRONT" AND AFTER "ONE ON EACH LAPEL" INSERT

"AND THE CUT OPENING OF BUTTONHOLES SHALL BE

POSITIONED 3/4 INCH FROM EDGE OF COAT."

PAGE 3, PARAGRAPH 3.2.2, BUTTONHOLES, LINE 5

AFTER "SQUARE-BAR TYPE" ADD "WORKED OVER

GIMP". AT END OF THE PARAGRAPH ADD:

"THERE SHALL BE TWO 3/4 INCH CUT, SQUARE BAR

TYPE BUTTONHOLES, ONE CENTERED ON THE BELT

FASTENER 3/8 INCH FROM THE END AND ONE

CENTERED ON THE RIGHT BACK VENT AS PER

MARK ON PATTERN. THE LAPEL BUTTONHOLES SHALL BE 3/4 INCH FROM

THE EDGE AND 1-1/2 INCHES DOWN FROM THE TOP

PAGE 3, PARAGRAPH 3.2.3 BUTTONS

LINE 2, DELETE "18" AND SUBSTITUTE "45"

PAGE 3, PARAGRAPH 3 AFTER "THE COAT SHALL HAVE THREE 24 LIGNE BUTTONS" DELETE "ONE BUTTON SHALL BE SEWN ON EACH SLEEVE LINING TO CORRESPOND WITH THE LOOPS ON THE REMOVABLE LINER'S SLEEVE BOTTOM AND ONE SHALL BE POSITIONED ON THE BELT FASTENER" AND INSERT "ONE BUTTON SHALL BE SEWN ON EACH SLEEVE LINING TO CORRESPOND WITH THE LOOPS ON THE REMOVABLE LINER'S SLEEVE BOTTOM AND ONE ON THE LEFT BACK VENT TO CORRESPOND TO THE BUTTONHOLE. THE COAT SHALL HAVE SEVEN 18 LIGNE BUTTONS; SIX ATTACHED TO THE 45 LIGNE BUTTONS ON THE COAT FRONT AND ONE POSITIONED ON THE BELT."

PAGE 3, AFTER PARAGRAPH 3.2.3 BUTTONS, INSERT

NEW PARAGRAPH AS FOLLOWS:"3.2.3.1 LAPEL BUTTON

PLACEMENT. THE TOP RIGHT LAPEL BUTTON SHALL

BE POSITIONED SO THAT THE LEFT COAT FRONT LAYS

SMOOTH AND FLAT WITHOUT DISTORTION AND THE

NECK OPENING SHALL BE 2 TO 2-1/2 INCHES BETWEEN

COLLARSTAND JOINING SEAM AND COLLARSTAND JOINING

SEAM ACROSS FRONT OF COAT."

PAGE 6, PARAGRAPH 3.3.2.4, LINE 2 AFTER

"COMBED COTTON" INSERT "OR STAPLE RAYON".

LINE 9: DELETE "2.5" AND SUBSTITUTE "1.5"

PAGE 6, PARAGRAPH 3.3.3, LINE 1 DELETE "1/4"

AND SUBSTITUTE "3/8".

PAGE 8 TABLE II DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING NEW TABLE:

1/ Size Diameter Lignes

Lignes, Min.

Total Quantity per coat

PAGE 8, PARAGRAPH 3.4.9 DELETE ENTIRELY AND

SUBSITUTE: "3.4.9 SLIDE FASTENER. THE

SLIDE FASTENER FOR THE COAT AND THE REMOV-

ABLE LINER SHALL BE A SEPARATING, NON-REVER-

SIBLE, RIGHT-HAND, LIGHT SIZE WITH AN ALUMINUM

OR BRASS CHAIN, SHORT TAB PULL. THE LENGTHS OF

THE SLIDE FASTENERS SHALL CONFORM TO THE SIZE

COAT WITH A MINIMUM LENGTH.OF 70 INCHES. THE

COLOR OF THE TAPE SHALL BE A GOOD MATCH TO THE

BASIC MATERIAL AND SHALL BE 7/16 OR 9/16 INCH

WIDE. THE ENDS OF THE SLIDE FASTENER SHALL

BE EQUIDISTANT FROM THE BOTTOM EDGE OF COAT.

PAGE 10 TABLE III, LIST OF PATTERN PARTS, DELETE "BACK VENT FACING" AND "POCKETS FACING, CORD" AND INSERT "NECK FACING" AND "NECK FACING, FUSIBLE".

PAGE 12, TABLE V - LINER FINISHED MEASUREMENTS,

DELETE TABLE V AND INSERT NEW TABLE AS FOLLOWS:

TABLE V LINER FINISHED MEASUREMENTS

ALL LENGTHS CHEST (1/) TOLERANCE +/- 3/4

SIZE

. 30------32------34------36------38------40 . 31 33 35 37 39 41

ALL LENGTHS CHEST (CONTINUED)

SIZE

. 42------44------46------48------50------52 . 43 45 47 49 51 53

. BACK LENGTH (2/) TOLERENCE +/- 1/2

SIZE

. 30------32------34------36------38------40

XS-- 33 33-1/4 33-1/2 33-3/4 34

S 34-3/4 35 35-1/4 35-1/2 35-3/4 36 R 36-3/4 37 37-1/4 37-1/2 37-3/4 38 L - 39 39-1/4 39-1/2 39-3/4 40

XL-- -- 41-3/4 42 42-1/4 42-1/2

. BACK LENGTH (CONTINUED)

SIZE

. 42------44------46------48------50------52

XS34-1/4 -- -- -- -- --

S 36-1/4 36-1/2 36-3/4 37 37-1/4 37-1/2 R 38-1/4 38-1/2 38-3/4 39 39-1/4 39-1/2 L 40-1/4 40-1/2 40-3/4 41 41-1/4 41 1/2

XL42-3/4 43 43-1/4 43-1/2 -- --

SLEEVE LENGTH (/3) TOLERANCE +/- 1/2

SIZE

. 30------32------34------36------38------40

XS-- 14-1/2 14-1/2 14-1/2 14-1/2 14-1/2

S 15-1/2 15-1/2 15-1/2 15-1/2 15-1/2 15-1/2 R 16-1/2 16-1/2 16-1/2 16-1/2 16-1/2 16-1/2 L -- 17-1/2 17-1/2 17-1/2 17-1/2 17-1/2

XL-- -- 18-1/2 18-1/2 18-1/2 18-1/2

SLEEVE LENGHT (CONTINUED)

SIZE

. 42------44------46------48------50------52

XS14-1/2 -- -- -- -- --

S 15-1/2 15-1/2 15-1/2 15-1/2 15-1/2 15-1/2 R 16-1/2 16-1/2 16-1/2 16-1/2 16-1/2 16-1/2 L 17-1/2 17-1/2 17-1/2 17-1/2 17-1/2 17-1/2

XL18-1/2 18-1/2 18-1/2 18-1/2 -- --

PAGE 16, PARAGRAPH 7.2.2 ASTM TEST METHODS

ADD "D-256 STANDARD TEST METHOD FOR IMPACT RE-

SISTANCE OF PLASTICS AND ELECTRICAL INSULATING

MATERIALS".

PACKAGING AND MARKING INSTRUCTIONS:

TEN (10) ALL WEATHER COATS ONE SIZE ONLY SHALL

BE PACKED IN A SNUG FITTING FIBERBOARD SHIPPING

CONTAINER CONFORMING TO ASTM-D5118, TYPE CF,

STYLE RSC, GRADE 275, VARIETY SW, CLASS DOMESTIC

WITH A DW LINER. THE DIMENSIONS OF THE CONTAINER

SHALL APPROXIMATE 20-H X 16-W X 24-L. METHOD OF

CLOSURE SHALL BE IN ACCORDANCE WITH ASTM-D-1974,

2A2, FIGURE 1 OR AS AND ALTERNATE 2B6 OR 2B7-

FIGURE 3.

AQL'S FOR COMMERCIAL ITEM DESCRIPTIONS

END ITEM DIMENSIONAL 2.5

VISUAL 4.0

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

USE OF SAMPLING PROCEDURES AND TABLES FOR

INSPECTION BY ATTRIBUTES, ANSI/AQSC Z1.4,

GENERAL INSPECTION LEVEL 2".

(Ref. W2850)

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY SCANNER. THE BAR-CODING ELEMENT SHALL BE A 13 DIGIT NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE SENSTIVE LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.

AQLS FOR COMMERCIAL ITEM DESCRIPTION (CIDS)

END ITEM DIMENSIONAL 2.5

VISUAL 4.0

PALLETIZATION 6.5

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

USE OF "SAMPLING PROCEDURES AND TABLE FOR

INSPECTION BY ATTRIBUTES". ANSI/ASQC Z1.4

GENERAL INSPECTION LEVEL II

(Ref. T7520)

LIST OF APPROVED WATER REPELLENT TREATMENTS FOR MILITARY FABRICS 1/

THE FOLLOWING FLUOROCHEMICALS ARE APPROVED "DURABLE" TYPE WATER REPELLENT TREATMENTS FOR USE ON MILITARY FABRICS. THEY MAY BE USED ALONE OR COMBINED WITH AN APPROVED EXTENDER COMPONENT TO PRODUCE A "QUARPEL" TYPE OF WATER REPELLENT TREATMENT REPELLENT TREATMENTS:

TRADE NAME SUPPLIER

AURAPEL FC-340 AURALUX DIV OF SYBRON

CHEMICAL CO.

P.O. BOX 113

YANTIC, CT 06389

TEL: 860-886-2626

BARPEL 1700 APOLLO CHEMICAL CORP.

PO BOX 2176

BURLINGTON, NC 27215

TEL: 910-226-1161

CHEMSHIELD 939 CHEM-TEX INC.

WR 930 P.O. BOX 1105

1891 N. COLUMBIA ST.

BLDG 106, MILLEDGEVILLE, GA 31061

TEL: 336-578-5476

FABRIC GUARD ML TANNER CHEMICAL CO., INC.

PO BOX 1967, FURMAN HALL

COURT, GREENVILLE, NC 29602

TEL: NO LISTING IN NC ON 800#

ZONYL B CIBA-GEIGY CORP.

ZONYL D P.O. BOX 11422

ZONYL RN 2/ HIGHPOINT, NC 27409

ZONY 6700 TEL: 888-396-2488

ZONYL 6700 GF

ZONYL 7040

ZONYL 8300

ZONYL 8070

ZONYL DWR

ZONYL MIL

FC-232 3M CORPORATION,

FC-251 PROTECTIVE PRODUCTS DIV.

FC-461 ST. PAUL, MN. 02895

FC-831 TEL: 612-737-0098

REPEARL F-14N MITSUBISHI INTERNATIONAL

REPEARL F-35 520 MADISON AVE.

REPEARL F-31 NEW YORK, NY 10022

TEL: 212-605-2440

800-851-5765

NK GUARD FG-280 NICCA USA, INC.

P.O. BOX 1600

5000 NELSON ROAD

FOUNTAIN INN, SC 29644

TEL: 864-862-1426

SEQUAPEL CQR SEQUA CHEMICAL CORP.

SEQUAPEL NRL ONE SEQUA DRIVE

SEQUAPEL WOR CHESTER, SC 29807-0070

SEQUAPEL WOR-46 TEL: 803-385-5181

TEX-TEL NI-40 AUTO CHEMICAL CO.

THREE PARKWAYS

PHILADELPHIA, PA 19102

TEL: 215-419-7000

UNIGUARD-5061 UNICHEM INC.

P.O. BOX 612

916 W. MAIN ST.

HAW RIVER, NC 27258

TEL: 336-578-5476

FLUOROGARD 1700 PUTNAM INDUSTRIES, INC

197 RIDGEWOOD AVE.

GLEN RIDGE, NJ 07028

TEL: NOT LISTED

FLO CHEM EXTRA 17-4 EMCO SERVICES INC.

P.O. BOX 2191

TAUNTON, MA 02780

TEL: 508-823-8852

1/ A SEPARATE LIST OF APPROVED WATER REPELLENT TREATMENTS EXISTS FOR FABRICS CONFORMING TO CLOTH, CAMOUFLAGE PATTERN; WOODLAND, COTTON AND NYLON, CLASS 2, MIL-C-44031 AND CLOTH, TWILL, CAMOUFLAGE PATTERN, COTTON AND NYLON FOR DESERT UNIFORM, CLASS 1A, MIL-C-44034.

2/ FOR POLYESTER, NYLON AND BLENDS OF MANMADE FIBERS ONLY.

ADDITIONAL INFORMATION FOR MIL-I-45208:

NOTE: MIL-I-45208 HAS BEEN CANCELLED AND REPLACED BY THE FOLLOWING: INTERNATIONAL STANDARDS ISO 9001:2008

OR AMERICAN SOCIETY FOR QUALITY ASQ 2008 VERSION.

HIGHER LEVEL INSPECTION SYSTEM:

THE INSPECTION SYSTEM(S) MUST BE SUBMITTED WITH YOUR

BID PROPOSAL FOR EVALUATION AND APPROVAL BY DLA TROOP

SUPPORT'S CONTRACTING OFFICER.

INSPECTION SYSTEM(S) COMPLIANT/BUT ARE NOT

LIMITED TO THE INTERNATIONAL STANDARDS ISO 9001

OR ASQ 2008 MAY BE UTILIZED IF TAILORED TO THE SPECIFIC

QUALITY ASSURANCE REQUIREMENTS IN THIS SOLICITATION.

(ref. T1286)

MIL-STD-129P, WITH CHANGE 4 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR SHIPMENT AND STORAGE - DATED

19 SEPTEMBER 2007

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.