TECH DATA CLOTH HERITAGE TAUPE 565.pdf

CLOTH, GABARDINE HERITAGE TAUPE 565 POLYESTER/WOOL 55%/45% CLASS 1 UNTREATED

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT.

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL

AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx.

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE

MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT

INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

CLOTH,GABARDINE: POLY/WOOL,GL-PD 19008A CLASS 1 UNTREATED HERITAGE TAUPE 565 6.8 OZ NOTE: All references to Certification Labeling and Procedures in the document do not apply to this procurement.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

CLASS 1 GABARDINE UNTREATED HERITAGE TAUPE 565, MOTHPROOFED.

INTERIM CHANGES FOR GL-PD-19008A DATED 10 FEB 2020

ADD THE FOLLOWING NEW PARAGARAPH: 4.4.3.1 LIMITS OF SLUBS AND KNOTS: ONLY SLUBS AND KNOTS WHICH EXEEED "D" OR 3-1/2 AS APPLICABLE, FOR SLUBS AND "C" FOR KNOTS ON THE

SEARS FABRIC DEFECT SCALE SHALL BE SCORED (SEE 6.6).

STANDARD SAMPLE IS IDENTIFIED AS ROLL NUMBER (Temporary Standard)TP011419 AND IS

APPLICABLE FOR SHADE, FINISH AND COLORFASTNESS.

ADDITIONAL INFORMATION FOR MIL-DTL-10176:

. THE CLOTH SHALL BE MOTHPROOFED IN ACCORDANCE WITH MIL-C-43665C, DATED 14 NOVEMBER 1986.

CERTIFICATE OF CONFORMANCE IS APPLICABLE FOR THE GRADING OF WOOL IN TOP FORM. (Ref.

20471) .

ADDITIONAL INFORMATION FOR MIL-C-43665:

. INTERIM SPECIFICATION CHANGES TO MIL-C-43665C:

. PAGE 2, PARA. 3.2, LINE 2, AFTER "TABLE 1 " INSERT "OR TABLE 1A", . PAGE 3, TABLE 1, DELETE "SODIUM (4,5-DICHLORO, 2-CHLOROMETHANE SULFONAMIDO) 3',4' 6',TRICHLORO)

DISHENYL ETHER (SEE 6.3.2) 0.26 0.60". .

PAGE 3, AFTER TABLE 1, INSERT THE FOLLOWING NEW TABLE: "TABLE 1A, MOTHPROOFING

COMPOUND. . % ON WEIGHT OF WOOL . MOTHPROOFING COMPOUND

MIN. MAX. EDOLAN ETS BEFORE DRYCLEANING *(3-PHENOXYPHENYL)

METHYL PLUS OR MINUS CIS/TRANS 3-(2-,2- DICCHLOROETHENYL)2,2-

DIMETHYLCYCLORPPANECARBOXYLATE. 0.058 0.40 CIS/TRANS RATIO:MAX.55% PLUS OR--

AFTER DRY-CLEAN MINUS CIS AND MIN.PLUS OR MINUS TRANS.(*PERMETHRIN) 0.029

0.40 .

PAGE 3,PARA.3.4, LINE 3, AFTER "3.2" INSERT "TABLE 1".

. PAGE 3, AFTER PARA. 3.4 INSERT NEW PARAGRAPH AS FOLLOWS: "3.4.1 PERCENT OF

MOTHPROOFING COMPOUND. THE PERCENTAGES OF MOTHPROOFING COMPOUND SPECIFIED IN TABLE 1A SHALL BE BASED ON WEIGHT OF PURE COMPOUND ON THE WOOL FIBER CONTENT WHEN TESTED BY HIGH PERFORMANCE LIQUID CHROMATOGRAPH (HPLC) METHOD, OBTAINABLE FROM BAYER CORP., ROCK

HILL, SC 29732 (SEE 4.2.2)".

. PAGE 5, PARAGRAPH 4.2.2,TABLE 11,DELETE THE FOLLOWING: CHARACTERISTIC

REQUIREMENT TEST . PARAGRAPH METHOD "SODIUM (4,5-

DICHLORO 2-CHLORO-METHANE SULFONAMIDO)3',4',6', TRICHLORO) DIPHENYL ETHER 3.4

4.3.1 3/ 4/" AND SUBSTITUTE THE FOLLOWING: CHARACTERISTIC REQUIREMENT

TEST . PARAGRAPH METHOD "EDOLAN ETS *(3-PHENOXYPHENYL

3.4.1 HPLC 7/ METHYL PLUS OR MINUS CIS/TRANS 3-(2,2-DICHLOROETHENYL) 2,2-

DIMETHYL-CYCLOPROPANECARBOXYLATE CIS/TTRANS RATIO: MAX.55% PLUS OR MINUS CIS AND MIN.

PLUS OR MINUS TRANS. *(PERMRTHRIN)" .

PAGE 5, PARAGRAPH 4.2.2, FOR CHARACTERISTIC EDOLAN ETS,UNDER TEST METHOD COLUMN, ADD

FOOTNOTE "7"/,ADD NEW FOOTNOTE "8"/.

PAGE 6, PARAGRAPH 4.2.2, TABLE II.AFTER FOOTNOTE "7/",ADD THE FOLLOWING:"8"/ THE

SAMPLE SHALL BE DRY-CLEANED FOR THREE CYCLES IN ACCORDANCE WITH AATCC TEST METHOD 86

BEFORE DETERMINING MOTHPROOFING COMPOUND CONTENT. .

PAGE 6, PARA.4.2.2, TABLE 11, AFTER FOOTNOTE 6/, INSERT "7/ HIGH PERFORMANCE LIQUID CHROMATOGRAPHY (HPLC) TEST METHOD MAY BE OBTAINED FROM BAYER CORP., ROCK HILL, SC 29732." .

PAGE 6, PARAGRAPHS 4.3,4.3.1,4.3.1.1,4.3.1.2, 4.3.1.3,4.3.1.4,4.3.1.5 DELETE

PARAGRAPHS IN THEIR ENTIRETY WITH NO REPLACEMENT. .

PAGE 7, PARAGRAPHS 4.3.1.6, 4.3.1.7, 4.3.1.7.1 DELETE PARAGRAPHS IN THEIR ENTIRETY

WITH NO REPLACEMENT. .

PAGE 8, PARAGRAPHS 4.3.1.7.2, 4.3.1.8, 4.3.1.8.1 DELETE PARAGRAPHS IN THEIR ENTIRETY

WITH NO REPLACEMENT. .

. PAGE 9, PARAGRAPHS 6.3 2, 6.4, 6.5, 6.6 DELETE PARAGRAPHS IN THEIR ENTIRETY WITH NO

REPLACEMENTS. .

PAGE 11, DELETE FIGURE 1 IN ITS ENTIRETY WITH NO REPLACEMENT. .

PAGE 5 TABLE II, UNDER TEST METHOD: DELETE "2015" AND SUBSTITUTE "2015.3" NOTE! MITTEN FF CONC. SUPPLIED BY CIBA-GEIGY CORP. P.O. BOX 11422, GREENSBORO, NC 27409 . EDOLAN ETS, SUPPLIED BY MILES INC.,MOBAY ROAD, PITTSBURGH,PA.15205-9741. . ARE APPROVED MOTH PROOFING AGENTS FOR MILITARY FABRICS. (Ref. T1118)

ADDITIONAL INFORMATION FOR MIL-I-45208:

NOTE: MIL-I-45208 HAS BEEN CANCELLED AND REPLACED BY THE FOLLOWING: INTERNATIONAL STANDARDS ISO 9001:2008 OR AMERICAN SOCIETY FOR QUALITY ASQ 2008 VERSION. (ref. T1286 ADDITIONAL INFO FOR FED-STD-4 GLOSSARY OF FABRIC IMPERFECTIONS: REVISION B: 7/29/64;

AMENDMENT 2: 9/12/75 NOTICE 1, DATED 10/1/87. DEV. TO FED. STD. 4B & AM. 2,

PAGE 2, SEC.I. PARA. 2.1. IN IMPERFECTION COMMERCIAL TERMINOLOGY AND GLOSSARY NO.

COLUMNS, AFTER SHADE BAR - 14 INSERT: "SHADED CLOTH-61B".

PAGE 8 PARA. 3.4, GLOSSARY NO. "61A- OFF SHADE", IN "DEFINITION" COLUMN, DELETE

":SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END". ADD NEW GLOSSARY NO. "SHADED CLOTH "61B-SHADED CLOTH (SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END) WITH THE

FOLLOWING DEFINITION: "COLOR DIFFERENCE BETWEEN THE RESPECTIVE CLOTH AREAS".

PAGE 22, SECTION III, PARAGRAPH 2.1, IN "IMPERFECTION COMMERCIAL TERMINOLOGY" AND

GLOSSARY NO." COLUMNS, AFTER "SHADE BAR-15" INSERT: "SHADED CLOTH - 62A"

PAGE 27, PARAGRAPH 3.4, GLOSSARY NO. "62-OFF SHADE" IN "DEFINITION" COLUMN DELETE:

"SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END". ADD NEW GLOSSARY NO, "62A-SHADED

CLOTH (SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END)" WITH THE FOLLOWING

DEFINITION: "COLOR DIFFERENCE BETWEEN THE RESPECTIVE CLOTH AREAS." DEVIATION FROM FED.

STD. 4B, AND AMEND 2:

PG 2, SECTION 1, PARA.2.1, IN "IMPERFECTION COMMERCIAL TERMINOLOGY" AND "GLOSSARY

NUMBER" COLUMNS, AFTER "SHADE BAR-14",INSERT: "SHADED CLOTH 61B".

PG 8, PARA.3.4, GLOSSARY NUMBER "61A-OFF SHADE" IN "DEFINITION" COLUMN, DELETE,

"SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END". ADD NEW GLOSSARY NO."61B SHADED

CLOTH "SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END" WITH THE FOLLOWING

DEFINITION; "COLOR DIFFERENCE BETWEEN THE RESPECTIVE CLOTH AREAS."

PAGE 22, SECTION III, PARAGRAPH 2.1, IN "IMPERFECTION COMMERCIAL TERMINOLOGY" AN

GLOSSARY NO." COLUMNS, AFTER "SHADE BAR-15" INSERT: "SHADED CLOTH - 62A"

.PAGE 27, PARAGRAPH 3.4, GLOSSARY NO "62-OFF SHADE" IN "DEFINITION" COLUMN DELETE:

"SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END". ADD NEW GLOSSARY NO, "62A-SHADED

CLOTH (SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END)" WITH THE FOLLOWING

DEFINITION: "COLOR DIFFERENCE BETWEEN THE RESPECTIVE CLOTH AREAS." Ref. T0202 - 04/04/07)

ADDITIONAL INFORMATION FOR MIL-STD-655D: . INTERIM CHANGES TO MIL-STD-655D: .

PAGE 3, PARA 4.1, ADD "QUALITY LEVEL 7" .

PAGE 5, TABLE I, UNDER QUALITY LEVEL"7", ADD UNDER ENTIRE SAMPLE "7 POINTS PER 100 SQ. YARDS", ADD UNDER INDIVIDUAL ROLLS "10 POINTS PER 100 SQ. YDS." (Ref. T0319) THE DEMERIT POINTS PER 100 SQ YDS SHALL NOT EXCEED A QUALITY LEVEL 12 IAW MIL-STD-655.

MIL-STD-129R - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR SHIPMENT

AND STORAGE DATED 18 FEBRUARY 2014

INTERIM CHANGES: OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS IN THE

DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE: THE NOMENCLATURE AND

MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT. IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN.

NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING

LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E w/CHANGE 1 23 December 2013 SUPERSEDING MIL-STD-147E 16 May 2008 DEPARTMENT OF DEFENSE STANDARD PRACTICE PALLETIZED UNIT LOADS ADDITIONAL INFORMATION

FOR MIL-STD-2073-1: