36P_and_45P_Tech_Data.docx

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS)

PGC 03875 (CWU-36/P TAN)

Special Measurement 8415000JKTI07 N/A

PGC 03876 (CWU-36/P SAGE GREEN)

Special Measurement 8415000JKT920 N/A

PGC 03873 (CWU-45/P TAN)

Special Measurement 8415000JKTI08 N/A

PGC 03874 (CWU-45/P SAGE GREEN)

Special Measurement 8415000JKTI06 N/A

SHADE STANDARD SAMPLE FOR AIR FORCE TAN 1657, CLOTH, TWILL, ARAMID, FLAME AND HIGH TEMPERATURE RESISTANT, PD WNUV 12-01 AVAILABLE UNDER ROLL NUMBER 18-05.

SHADE STANDARD SAMPLE FOR AIR FORCE SAGE GREEN 1658, CLOTH, TWILL, ARAMID, FLAME AND HIGH TEMPERATURE RESISTANT, PD WNUV 12-01 AVAILABLE UNDER ROLL NUMBER 17-01.

JACKET, FLYER’S, CWU-45/P BE MADE IN ACCORDANCE WITH MIL-J-83388E DATED 18 JUNE 1992.

PATTERN DATE: 17 SEPTEMBER 2008

JACKET, FLYER’S, CWU-36/P SHALL BE MADE IN ACCORDANCE WITH MIL-J-83382C AMENDMENT 1 DATED 1 NOVEMBER 1985 AND MIL-J-83382C DATED 30 OCTOBER 1981.

PATTERN DATE: 22 APRIL 1992

INTERIM CHANGES TO MIL-J-83382C, AMENDMENT 1:

***NOTE: RENUMBER OPERATIONAL CHANGES TO

CORRESPOND WITH RENUMBERED BASIC SPECIFICATION

CHANGES***

PAGE 1, UNDER "PAGE 2" LINE 1, DELETE

"MIL-T-44100" AND SUBSTITUTE "A-A-55195".

PAGE 1, UNDER "PAGE 3" PARAGRAPH 3.1.4, LINES 1 AND 2

DELETE "SIZE T-35 OF MIL-T-44100" AND SUBSTITUTE

"TYPE I, NOMINAL TEX SIZE 39 OF A-A-55195".

PAGE 1, UNDER "PAGE 20" LINE 4, AFTER "FOLDED

EDGE" ADD NEW SENTENCE "THE ZIPPER SHALL BE

POSITIONED SO AS TO RUN UP TO A MINIMUM 3/8 INCH

AND MAXIMUM OF 1/2 INCH FROM THE BOTTOM OF THE

COLLAR."

INTERIM CHANGES TO MIL-J-83382C:

PAGE 1, SPECIFICATIONS, FEDERAL, DELETE "V-F-106" AND SUBSTITUTE "A-A-55634"; DELETE "V-T-276" AND SUBSTITUTE "A-A-52094"; DELETE "CCC-C-426" AND SUBSTITUTE "A-A-52085";DELETE "DDD-L-20" AND SUBSTITUTE "MIL-DTL-32075"; DELETE "PPP-B-636" AND SUBSTITUTE "ASTM-D-1974"; ADD "A-A-55126 FASTENER TAPE, HOOK AND PILE, SYNTHETIC".

PAGE 2, MILITARY, DELETE "MIL-F-21840"; ADD "MIL-STD-147 PALLETIZED UNIT LOADS FOR 40 INCHES X 48 INCHES PALLET."

Page 2, Paragraph 2.1.1, under "Military" delete "Mil-W-5664 Webbing, Textile, Elastic, Cotton."

PAGE 2 AFTER "STANDARDS, MILITARY," ADD HEADING:

"OTHER GOVERNMENT DOCUMENTS" THEN ADD:

PURCHASE DESCRIPTION NO. WNUV 12-01 CLOTH, TWILL, ARAMID, FLAME AND HIGH-TEMPERATURE RESISTANT PURCHASE DESCRIPTION NO. WNUV 12-02 CLOTH, META-ARAMID WARP, META-ARAMID FILLING, PARA-ARAMID FILLING, NAPPED, FLAME AND HIGH-TEMPERATURE RESISTANT"

PAGE 3, PARAGRAPH 3.1.1, LINE 2, AFTER "MIL-C-81814" ADD "OR PURCHASE DESCRIPTION WNUV 12-01 CLOTH, TWILL, ARAMID, FLAME AND HIGH TEMPERATURE RESISTANT."

PAGE 3, PARAGRAPH.3.1.1, LINE 3, DELETE "SHADE NO. 1565"; ADD "SHADE TAN NO. 1657 OR SAGE GREEN NO. 1658."

Page 3, paragraph 3.1.2, line 1, after "Mil-C-83450" add "or Purchase Description WNUV 12-02 Cloth, Meta-Aramid Warp, Meta-Aramid Filling, Para-Aramid Filling, Napped, Flame and High-Temperature Resistant."

PAGE 3, PARAGRAPH 3.1.3, LINE 2, DELETE "CCC-C-426"

AND SUBSTITUTE "A-A-52085".

PAGE 3, PARAGRAPH 3.1.4, LINE 4, DELETE "TYPE IA3,

TICKET NO. 30, 3 PLY OF V-T-276" AND SUBSTITUTE

"TYPE I, TICKET NO. 30, 3 PLY OF A-A-52094".

Page 3, paragraph 3.1.5, delete in its entirety.

PAGE 3, PARAGRAPH 3.1.6 SLIDE FASTENERS, ADD AT THE

END OF THE PARAGRAPHGRAPH "THE SIZE OF THE HOLE OF

THE PULL TAB USED ON THE PENCIL POCKET SHALL NOT

EXCEED 3/16 INCH. AS AN ALTERNATE, A PULL TAB

WITHOUT ANY HOLE MAY BE USED."

PAGE 3, PARAGRAPH 3.1.7, LINE 4, DELETE "NO. 1525"; ADD "TAN NO. 1657 OR SAGE GREEN NO. 1658."

PAGE 3, PARAGRAPH 3.1.8, LINES 3 AND 4, DELETE "TYPE

I, CLASS 1 OF MIL-F-21840" AND SUBSTITUTE "TYPE

I, CLASS 1 OF A-A-55126".

Page 3 Para. 3.1.10 Delete in its entirety

PAGE 4, TABLE I, UNDER APPLICATION FOR SLIDE

FASTENER COLUMN, DELETE ALL REFERENCES TO

"CIGARETTE" AND SUBSTITUTE "UTILITY

PAGE 4, PARAGRAPH 3.2, LINE 3, DELETE "CIGARETTE"

SUBSTITUTE "UTILITY"

Page 6, Table III, delete "Operation No. 1 c" in its entirety.

PAGE 7, TABLE III, ADD "OPERATION 4 OUTERSHELL, (a)

OVEREDGE THE FRONTS, BACKS, AND SLEEVES.

STITCH TYPE 502, 503 OR 504

SEAM AND STITCH TYPE SSA-1

STITCHES PER INCH 8".

PAGE 7, TABLE III, OPERATION 4, ADD NEW OPERATION: "(b) AS AN ALTERNATE TO 4(a) ABOVE, OVEREDGING CAN BE

DONE WHEN PERFORMING JOINING OPERATIONS

9(A), 10(A), 12(A), AND 13(A)".

PAGE 7, TABLE III, MAKE TWO FRONT POCKETS, DELETE " NUMBER 4" AND SUBSTITUTE "5".

*******RENUMBER EXISTING OPERATIONS ACCORDINGLY***********

NOTE: IF OPTIONAL RENUMBERED OPERATIONS 9(C), 9(F),

10(C), AND 12(C) ARE USED, THEN OPERATION 4(A) IS NOT

APPLICABLE.

Page 9, Table III, delete "Operation No. 6" in its entirety.

Page 9, delete Operation 7 (a)

PAGE 10, TABLE III, OPERATION 7, IN PARAGRAPH

IDENTIFIER, DELETE "CIGARETTE" AND SUBSTITUTE

"UTILITY"

PAGE 11, TABLE III, OPERATION 7(E), LINE 1,

DELETE "CIGARETTE" AND SUBSTITUTE "UTILITY"

PAGE 11, TABLE III, OPERATION 7(H), LINE 1

DELETE "CIGARETTE" AND SUBSTITUTE "UTILITY".

PAGE 11, TABLE III, OPERATION 7(J), LINE 2

DELETE "CIGARETTE" AND SUBSTITUTE "UTILITY".

PAGE 12, TABLE III, OPERATION 7, UNDER NOTE,

LINES 1 AND 5, DELETE "CIGARETTE" AND SUBSTITUTE

"UTILITY"

PAGE 12, OPERATION 7, NOTE: LINE 2, DELETE "3 1/2

INCHES" AND SUBSTITUTE "4 INCHES".

PAGE 12, RENUMBERED OPERATION 8, UNDER "NOTE", AFTER

"AND PENCIL POCKET." ADD: "THE SLIDE FASTENER

SHALL CLOSE WITH THE SLIDER AT THE TOP OF THE

POCKET."

PAGE 12, OPERATION 9, MAKE SLEEVES. AFTER

OPERATION 9(A) INSERT THE FOLLOWING:

"(B) AS AN ALTERNATE TO 4(A), OVEREDGE ELBOW SEAM

STITCH TYPE 502, 503, OR 504---SSA-1---8".

RELETTER SUBSEQUENT PARAGRAPH.

PAGE 13, OPERATION 10, JOIN SHOULDERS.

AFTER OPERATION 10(A) INSERT THE FOLLOWING:

"B. AS AN ALTERNATE TO 4(A), OVEREDGE SHOULDER

SEAM. STITCH TYPE 502, 503, OR 504---SSA-1---8".

RELETTER SUBSEQUENT PARAGRAPH.

PAGE 14, RENUMBERED OPERATION 10(B) IN STITCH TYPE COLUMN

ADD "OR 401".

PAGE 14, OPERATION 11, "INSERT CORDED BEADING IN

FRONT OPENING" SHOULD FOLLOW OPERATION 20(A)

IN ORDER TO BE PERFORMED CORRECTLY.

PAGE 14, RENUMBERED OPERATION 11(A), LINE 5 "DELETE

"AT THE LOWER FOL NOTCH" AND SUBSTITUTE "AT THE

BOTTOM OF THE OUTERSHELL EXTENSION PIECES."

PAGE 14, TABLE III, OPERATION 12, JOIN SIDE SEAMS, AFTER

OPERATION 12(A) INSERT THE FOLLOWING:"(B)

AS AN ALTERNATE TO 4(A), OVEREDGE SIDE SEAM.

STITCH TYPE 502, 503 OR 504---SSA-1---8".

RELETTER SUBSEQUENT PARAGRAPH.

PAGE 15, TABLE III, OPERATION 13, ATTACH SLEEVES, AFTER

OPERATION 13(A) INSERT THE FOLLOWING:

"(B) AS AN ALTERNATE TO 4(A), OVEREDGE SLEEVES

TO ARMHOLE SEAM, CATCHING THE ELASTIC WEBBING.

STITCH TYPE 502, 503, OR 504---SSA-1---8".

RELETTER SUBSEQUENT PARAGRAPH.

Page 15, delete Operation 13(b), and replace with the following "Operation 13(b) Turn and raise stitch on the fronts and backs, from the elbow seam to the front armhole notch or approximately 3 inches from the shoulder seam , with a single row of stitching ¼ inch from the folded edge.

PAGE 16, RENUMBERED OPERATION 14, SUBPARAGRAPH (D) BETWEEN

THE WORDS" "STAND" AND "TO THE LEAF" ADD "AND

TOP COLLARSTAND."

PAGE 18, OPERATION 17(F) UNDER "STITCH TYPE" ADD

"OR 401"

PAGE 18, RENUMBERED OPERATION 17(H), UNDER SEAM AND

STITCH TYPE, DELETE "LSQ-2(A)" AND SUBSTITUTE

"LSQ-2(B)"

PAGE 18, OPERATION 18(A),(B), AND (C), "JOIN SIDE SEAMS

OF LINING" MUST BE PERFORMED PRIOR TO OPERATION

17(G),(H), AND (I).

PAGE 21, OPERATION 25 (A), ATTACH LABELS,

LINE 5, AFTER "SIZE LABEL." INSERT "AS AN

ALTERNATE, POSITION THE TOP OF THE COMBINATION

SIZE, IDENTIFICATION AND INSTRUCTION LABEL

DIRECTLY BELOW THE HANGER.", AND LINE 6, AFTER

"INSTRUCTION LABEL" INSERT OR THE ALTERNATE

COMBINATION, SIZE, IDENTIFICATION AND

INSTRUCTION LABEL".

PAGE 21, AFTER RENUMBERED OPERATION 25(A) ADD

"(B) A BAR-CODED LABEL/TAG AS SPECIFIED IN

DDD-L-20 FOR TYPE VIII, CLASS 17 LABEL SHALL BE

ATTACHED SO THAT IT IS COMPLETELY VISIBLE ON

ON EACH JACKET AND CAUSES NO DAMAGE TO THE ITEM" PAGE 24, TABLE IV, UNDER PATTERN PARTS COLUMN, LINES 5 AND 6, DELETE "CIGARETTE" AND SUBSTITUTE

"UTILITY".

PAGE 25, PARAGRAPH 3.6, LABELS. LINE 6, AFTER

"DDD-L-20" DELETE REMAINER OF SENTENCE AND

SUBSTITUE:". AS AN ALTERNATE, A COMBINATION

IDENTIFICATION, SIZE AND INSTRUCTION LABEL SHALL

BE USED AND SHALL CONFORM TO TYPE VI, CLASS 14

OF DDD-L-20 EXCEPT THAT THE SPECIFICATION

NUMBER SHALL BE INCLUDED. THE INSTRUCTION LABEL

SHALL CONTAIN THE FOLLOWING INFORMATION:".

PAGE 25, PARAGRAPH 3.6, LINE 11, AFTER "JACKET" DELETE

THE REST OF THE SENTENCE AND SUBSTITUTE "IS TO

BE DRYCLEANED ONLY."

PAGE 25, AFTER PARAGRAPH "3.6" ADD NEW PARAGRAPH

"3.6.1 LABEL/TAG. EACH JACKET SHALL BE

INDIVIDUALLY BAR-CODED WITH THE TYPE VIII,

CLASS 17 LABEL/TAG OF DDD-L-20."

PAGE 26, PARAGRAPH 4.2.2.1, LINES 4 & 5, DELETE "2.5"

"15.0" AND "40.0" AND SUBSTITUTE "1.5", "10" AND

"25" RESPECTIVELY.

PAGE 27, TABLE VII, UNDER "MATERIAL DEFECTS AND WORKMANSHIP DAMAGES" IN DEFECTS 2 AND 3 DELETE "FUZZ BALLS; SLUBS OR KNOTS (EXCEEDING LIMITS SHOWN ON FIGURE 1 OF FED-STD-4)."

PAGE 31, TABLE VII, LINES 3,5,7,9,14,15,17, AND

19, DELETE "CIGARETTE" AND SUBSTITUTE "UTILITY"

PAGE 31 TABLE VII, DEFECTS, LINE 6, DELETE "3

INCHES AND 4 INCHES" AND SUBSTITUTE "3 1/2

INCHES AND 4 1/2 INCHES" RESPECTIVELY.

PAGE 31, TABLE VII, UNDER "ELASTIC WEBBING IN BACK PANEL", DELETE DEFCTS 1, 2 AND 3 IN THEIR ENTIRETY.

PAGE 32, TABLE VII, UNDER "DEFECT" COLUMN AFTER

LABEL DEFECTS ADD THE FOLLOWING NEW DEFECTS:

"BAR CODE OMITTED OR NOT READABLE BY SCANNER, MINOR A

HUMAN-READABLE INTERPREATATION (HRI)OMITTED OR ILLEGIBLE,

MINOR A

NOT VISIBLE ON FOLDED PACKAGED ITEM, MINOR A

CAUSES DAMAGE TO THE ITEM, MAJOR"

PAGE 33, PARAGRAPH 5.2.2, LINE 4, DELETE "24 INCHES

BY 20 INCHES BY 16 INCHES" AND SUBSTITUTE "20

INCHES BY 16 INCHES BY 24 INCHES."

DEVIATIONS/CHANGES TO MIL-J-83388E DATED:18 JUNE 1992:

PAGE 2, UNDER "SPECIFICATIONS, FEDERAL", DELETE "V-F-106" AND SUBSTITUTE "A-A-55634". DELETE "KK-L-2004" AND SUBSTITUTE "MIL-DTL-32092". DELETE "NN-P-71" AND THERE IS NO SUBSTITUTION.

DELETE "DDD-L-20" AND SUBSTITUTE "MIL-DTL-32075". DELETE "PPP-B-636 AND SUBSTITUTE "ASTM D 5118 AND ASTM D 1974".

DELETE PPP-T-45" AND SUBSTITUTE "A-A-1671".

Page 2, Paragraph 2.1.2 under "SPECIFICATIONS, FEDERAL" delete "MIL -W-5664 Webbing, Textile, Elastic, Cotton."

PAGE 2, UNDER "SPECIFICATIONS, MILITARY", DELETE "MIL-F-21840" AND SUBSTITUTE "A-A-55126". DELETE "MIL-T-44100" AND SUBSTITUTE "A-A-55195".

PAGE 3, UNDER "STANDARDS, FEDERAL", DELETE "FED-STD-751" AND SUBSTITUTE "ASTM-D-6193".

PAGE 3, UNDER "STANDARDS, MILITARY" DELETE "MIL-STD-105" AND SUBSTITUTE MIL-STD-1916". DELETE "MIL-STD-2073-2" AND SUBSTITUTE "MIL-STD-2073-1".

PAGE 3, AFTER "STANDARDS, MILITARY" AND BEFORE "2.1", ADD HEADING "OTHER GOVERNMENT DOCUMENTS", THEN ADD:

"PURCHASE DESCRIPTION WNUV 12-01 CLOTH, TWILL, ARAMID, FLAME AND HIGH-TEMPERATURE RESISTANT"

Page 4, Paragraph 3.2.1, line 3, after "Mil-C-81814," add "or Purchase Description WNUV 12-01 Cloth, Twill, Aramid, Flame and High-Temperature Resistant "

PAGE 4, PARAGRAPH 3.2.1, LINE 3, ADD "FOR CLASS 1; AND

USA COLOR SHADE 1653 DESERT TAN FOR CLASS II".

Page 4, Paragraph 3.2.1, line 3, delete: "Shade No 1565"; add "Shade. Tan No. 1657 or Sage Green No. 1658."

PAGE 4. PARAGRAPH 3.2.1.1, LINE 3, ADD "FOR CLASS 1;

AND USA COLOR SHADE NO. 1657 DESERT TAN FOR

CLASS II".

Page 4, paragraph 3.2.1.1, line 3, after "Mil-C-81814," add "or Purchase Description No. WNUV 12-01 Cloth, Twill, Aramid, Flame and High-Temperature Resistant."

Page 4, paragraph 3.2.1.1, line 3, delete "Shade No. 1565"; add "Shade Tan No.1657 or Sage Green No. 1658."

Page 4, Paragraph 3.2.2, line 3, delete "No. 1565"; add "Tan 1657 or Sage Green No. 1658."

PAGE 4, PARAGRAPH 3.2.2, LINE 3, AFTER 6.3., ADD "FOR CLASS

1". FOR CLASS II THE MATERIAL FOR THE QUILTED

LINING SHALL CONFORM TO MIL-B-81813 AND SHALL

BE A GOOD MATCH TO THE BASIC MATERIAL.

PAGE 5, PARAGRAPH 3.2.4 THREAD. LINE 2, DELETE "SIZE T

35 FOR MIL-T-44100" AND SUBSTITUTE "A-A-55195,

TYPE I, NOMINAL TEX 39".

Page 5, paragraph 3.2.5, delete in its entirety

Page 6, paragraph 3.2.7, line 4, delete "No. 1565"; add "Tan No. 1657 or Sage Green No. 1658."

PAGE 6, PARAGRAPH 3.2.7, LINE 5, AFTER 6.3 ADD "FOR

CLASS THE WAISTBAND AND WRISTLETS SHALL BE A GOOD

MATCH TO THE BASIC MATERIAL DESERT TAN 1653.

PAGE 6, PARAGRAPH 3.2.7, LINE 5, ADD "FOR CLASS 1: AND

USA COLOR SHADE 1653 DESERT TAN FOR CLASS II".

PAGE 7, PARAGRAPH 3.2.8 HOOD LINING. LINE 2,

AFTER TYPE INSERT "I OR,"

PAGE 7, PARAGRAPH 3.2.8, HOOD LINING, AT END OF THE PARAGRAPH, ADD THE FOLLOWING:

"POLYESTER FIBER, 6 OR 7 DENIER, COLOR SG, STYLE 1389-669 CAN BE USED IN LIEU OF TYPE I, 100 % ACRYLIC OF MIL-C-6590."

PAGE 7, PARAGRAPH 3.2.9 DRAWSTRINGS, LINE 4 AFTER "THE"

INSERT "TYING"

Page 7 Para 3.2.15 Delete in its entirety

PAGE 9, PARAGRAPH 3.5, PATTERNS, TABLE III, UNDER "PARTS CUT" NEXT TO UNDERCOLLAR STAND, INSERT "1".

PAGE 13, OPERATION 4(G), UNDER "SEAM/STCH TYPE"

COLUMN DELETE "LSBJ-1" SUBSTITUTE "LSBL-2(A)".

PAGE 13, OPERATION 4(H), UNDER "SEAM/STCH TYPE" COLUMN

DELETE "LSD-1" AND SUBSTITUTE "LSBL-1(B)".

Page 14, delete Operation 6 (a)

Page 14, Table IV, Operation No. 6, delete "and elastic webbing" from the title, delete 6. (b) in its entirety.

PAGE 16, TABLE IV, OPERATION 8 (C), LINE 2, BEFORE

"JOIN" INSERT "WITH THE TOP SLEEVE OVERLAPPING

THE UNDER SLEEVE".

PAGE 17, TABLE IV, OPERATION 9 (C), LINE 2, BEFORE

"JOIN" INSERT "WITH THE BACK OVERLAPPING THE

FRONT"

PAGE 18, TABLE IV, OPERATION 12 (C), LINE 2,

BEFORE "JOIN" INSERT "WITH THE FRONT OVERLAPPING

THE BACK".

PAGE 19. TABLE IV., OPERATION 15 (B), AT THE END

OF THE PARAGRAPH INSERT "OR WHEN SAFETY STITCH

IS USED, THE SEAM SHALL BE POSITIONED TOWARDS

THE BACK OF THE JACKET PRIOR TO TOP STITCHING."

AND UNDER STCH TYPE SEAM/STCH TYPE STCH PER IN"

COLUMNS INSERT "301 OR 401 LSBM-3 OR LSBM-4

10-12".

PAGE 20, TABLE IV., OPERATION 16 (B), AT THE END

OF THE PARAGRAPH INSERT "OR WHEN SAFETY STITCH

IS USED, THE SEAM SHALL BE POSITIONED TOWARDS

THE BACK OF THE JACKET PRIOR TO TOPSTITCHING."

AND UNDER "STCH TYPE SEAM TYPE/STCH TYPE STCH

PER IN " COLUMNS INSERT "301 OR 401 LSBM-3 OR

LSBM-4 10-12."

PAGE 20, TABLE IV, OPERATION 17 (A), RELABEL AS

OPERATION 17(C) AND LINE 2, AFTER "LINING" DE-

LETE "FROM THE SLEEVE TERMINAL TO THE BOTTOM

EDGE" SUBSTITUTE "FROM THE BOTTOM OF THE

SLEEVE AT THE CUFF TO THE BOTTOM OF THE JACKET."

PAGE 20, TABLE IV., OPERATION 17 (B), AT THE END

OF THE PARAGRAPH INSERT "OR WHEN SAFETY IS USED

THE SEAM SHALL BE POSITIONED TOWARDS THE BACK OF

THE JACKET PRIOR TO TOPSTITCHING." AND UNDER

"STCH TYPE SEAM/STCH TYPE STCH PER IN" COLUMNS

INSERT "301 OR 401 LSBM-3 OR LSBM-4 10-12".

PAGE 20, TABLE IV, OPERATION 17.B, RELABEL AS

OPERATION 17 (D).

PAGE 20, TABLE IV, OPERATION 17 (C), RELABEL AS

OPERATION 17 (A).

PAGE 20, TABLE IV, OPERATION 17(D), RELABEL AS

OPERATION 17(B).

PAGE 20, TABLE IV, AT THE END OF OPERATION 17,

ADD "NOTE: OPERATIONS 17(B) AND 17(D) MAY BE

PERFORMED IN ONE OPERATION.".

PAGE 21, TABLE IV, OPERATION 19(B), LINE 1, AFTER

"EDGE" INSERT "OF WAISTBAND".

PAGE 30, ADD NEW PARAGRAPH; "3.8.2 BAR CODE

LABEL/TAG. EACH ITEM SHALL BE INDIVIDUALLY

BAR-CODED WITH A TYPE VIII, CLASS 17 LABEL/TAG

OF DDD-L-20. THE LABEL/TAG SHALL BE LOCATED SO

THAT IT IS COMPLETELY VISIBLE ON THE ITEM WHEN

IT IS FOLDED AND/OR PACKAGED AS SPECIFIED AND

SHALL CAUSE NO DAMAGE TO THE ITEM.".

PAGE 33, PARAGRAPH 4.4.2.1, LINES 4, 5 AND 6, DELETE

"2.5", "15.0" AND "40.0" AND SUBSTITUTE "1.5",

"10" AND "25".

PAGE 35, 36, TABLE VIII, UNDER "MATERIAL DEFECTS AND WORKMANSHIP DAMAGES" DELETE DEFECTS 2 AND 3 IN THEIR ENTIRETY.

PAGE 36, TABLE VIII, CLASSIFICATION OF DEFECTS,

LINE 20, UNDER DEFECT COLUMN DELETE "BASIC

FABRIC CONTAINING ONE MISSING OR BROKEN PICK OR

END.", AND UNDER MINOR - A, DELETE "X".

PAGE 36, TABLE VIII, CLASSIFICATION OF DEFECTS,

LINE 20, ADD THE FOLLOWING;

DEFECT MAJOR

BASIC FABRIC MISSING END, RUNNING

ENTIRE LENGTH OF MAJOR PART X

BASIC FABRIC CONTAINING ANY SHADE BAR X

BASIC FABRIC COLOR IS NOT AS SPECIFIED X".

PAGE 42, TABLE VIII, UNDER "ELASTIC IN BACK PANEL" DEFECTS 1, 2 AND 3 (ALL DEFECTS), DELETE IN THEIR ENTIRETY.

PAGE 44, TABLE VIII, UNDER LABEL DEFECT, ADD THE

FOLLOWING;

"BAR CODE LABEL/TAG

BAR CODE OMITTED OR NOT READIBLE

BY SCANNER MINOR B

HUMAN READIBLE INTERPRETATION (HRI)

OMITTED OR ILLEGIBLE MINOR B

NOT VISIBLE ON FOLDED, PACKAGED ITEM MINOR B

CAUSES DAMAGE TO THE ITEM MAJOR".

PAGE 46, PARAGRAPH 5.2.2, LINE 4, DELETE"RSC-L" AND

SUBSTITUTE "RSC".

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY SCANNER. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE SENSTIVE LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.

"MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR A-A-52085:

CID A-A-52085 IS AUTHORIZED FOR USE IN PREFERENCE TO CCC-C-426

(ref. T1477 - 5/23/06)

ADDITIONAL INFORMATION FOR A-A-52094A THREAD, COTTON

NO ADDITIONAL INFORMATION

(ref. T1481)

ADDITIONAL INFORMATION FOR MIL-C-3735:

STANDARD SAMPLE FOR SAGE GREEN 1590 IS IDENTIFIED AS PIECE #52 AND REFERENCED FOR SHADE ONLY.

INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS MIL-C-44436, ROLL #3729 (THE FOLIAGE GREEN 502 AREA OF THE PATTERN), AND REFERENCED FOR SHADE ONLY.

INTERIM CHANGES TO MIL-C-3735E:

PAGE 4, PARAGRAPH 2.2 OTHER PUBLICATIONS. ADD THE FOLLOWING BELOW "METHOD NO. 8 COLORFASTNESS TO CROCKING: AATCC CROCKOMETER METHOD" "AATCC 20 - FIBER ANALYSIS: QUALITATIVE"

PAGE 4, PARA. 3.3.3.1, FIBER.: DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING:

"3.3.3.1 ARAMID FIBER BLEND. THE BLEND SHALL CONSIST OF 92 PERCENT META-ARAMID FIBER, 5 PERCENT PARA-ARAMID FIBER AND 3 PERCENT CONDUCTIVE FIBER. THE ARAMID FIBERS SHALL HAVE A NOMINAL DENIER OF 1.5 TO 1.7 DENIER PER FILAMENT, A STAPLE LENGTH OF 1-1/2 TO 2 INCHES, AND SHALL NOT CHAR AT A TEMPERATURE LESS THAN 675 DEG. F.. THE CONDUCTIVE FIBER SHALL BE A NYLON SHEATHED CARBON CORE FIBER AND SHALL BE 3 DENIER PER FILAMENT AND 1/1/2 INCHES TO 2 INCHES IN STAPLE LENGTH (SEE 6.4)."

PAGE 5, PARAGRAPH 3.4, LINE 3, AFTER "(SEE 6.6)" ADD "OR FOLIAGE GREEN 504".

PAGE 10, PARAGRAPH 3.13, PH., LINE 2: AFTER "8.0" DELETE "AND".

PAGE 10, PARAGRAPH 3.13, PH., LINE 3: AFTER "8.5" ADD "AND FOR THE TYPE IV CUFFS AND CLOTH SHALL NOT BE LESS THAN 5.0 NOR MORE THAN 8.0".

PAGE 12, TABLE IV. COMPONENT TESTS UNDER TEST METHOD COLUMN, LINE 6 DELETE "1600" AND SUBSTITUTE "AATCC 20".

PAGE 23, PARAGRAPH 6.4: DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING:

"6.4 TYPE IV FIBER BLEND. THE FINISHED CLOTH AND CUFF FIBER BLEND HAS BEEN SUCCESSFULLY MANUFACTURED WITH YARNS PRODUCED FROM AN INTIMATE FIBER BLEND OF 92 PERCENT NOMEX, 5 PERCENT KEVLAR AND 3 PERCENT P-140. THE FIBER BLEND IS AVAILABLE IN BALE FORM FROM E.I. DUPONT DE NEMOURS & CO. INC., WILMINGTON, DE. 19880."

ELECTROSTATIC DECAY TESTING IS NOT REQUIRED FOR THIS CUFF.

(ref. T0941 - 5/23/06)

ADDITIONAL INFORMATION FOR MIL-C-81814C:

PAGE 2, PARAGRAPH 2.2, UNDER AMERICAN ASSOCIATION OF

TEXTILE CHEMISTS AND COLORISTS, ADD: "AATCC

158 - DIMENSIONAL CHANGES ON DRYCLEANING

IN PERCHLOROETHYLENE: MACHINE METHOD".

PAGE 3, PARAGRAPH 3.5, TABLE I, PHYSICAL

PROPERTIES. "REQUIREMENTS COLUMN. UNDER

"SHRINKAGE AFTER TEN (10) LAUNDERINGS

PERCENT, MAX, WARP", DELETE "2.0" AND

SUBSTITUTE "4.0".

PAGE 8, 4.5, TABLE II "TEST METHOD", ANTISTATIC

FINISH,/AFTER DRY CLEANING": DELETE "5556".

PAGE 9, TABLE II, FOOTNOTE "3" DELETE AND

SUBSTITUTE "AATCC TEST NUMBER 158-1985

DIMENSIONAL CHANGES ON DRYCLEANING IN

PERCHLOROETHYLENE: MACHINE METHOD".

PAGE 11, PARAGRAPH 6.5, LINE 2, DELETE "ONYX

CHEMICAL CO., 190 WARREN ST., JERSEY CITY

NJ 07032, AND STANAZ, (NOT STANAZ 1166)

STANDARD CHEMICAL PRODUCTS, INC., HOBOKEN, NJ

07030" AND SUBSTITUTE "RHONE POULNOC, HURRICANE

SHOALS RD., LAWRENCEVILLE, GA 30243".

STANDARD SAMPLE FOR SAGE GREEN 1565 IS

IDENTIFIED AS ROLL NO. 99-01 AND REFERENCED

FOR SHADE AND COLORFASTNESS.

ADDITIONAL INFORMATION FOR MIL-C-83242:

NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR MIL-I-45208:

NOTE: MIL-I-45208 HAS BEEN CANCELLED AND REPLACED BY THE FOLLOWING: INTERNATIONAL STANDARDS ISO 9001:2008

OR AMERICAN SOCIETY FOR QUALITY ASQ 2008 VERSION.

(ref. T1286 )

ADDITIONAL INFORMATION FOR FED-STD-191:

FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO END ITEM SPECIFICATION FOR REPLACEMENT ASTM.

INTERIM CHANGES TO FED-STD-191A:

TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT ONE INCH OF SPECIMEN LIES WITHIN THE CLAMP AND ONE INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF THE VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE".

TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA 4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91".

THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540, AND 1550. PARA 5.1 OF THESE TEST METHODS REQUIRE THE USE OF 1,1,1- TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-TRICHLORETHANE IS AN OZONE DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN BASIC OR ANY REFERENCED DOCUMENT.

METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD. PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (INNER FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE."

METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5, PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACK TEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60 MINUTES OR UNTILSAMPLES ARE DRY IN A ROTATING TUMBLE DRYER."

PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACKTEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40 MINUTES OR UNTIL SAMPLES ARE DRY."

METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1, PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1, PARA. 4: DELETE "APPARTUS" AND SUBSTITUTE "APPARATUS". PAGE 1, PARA. 5.1, LINE 3: AFTER "AT" DELETE"APPROXIMATELY".

PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6: AFTER "TO" ADD "+-".

PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING IT OVER THE SENSOR OPENING. THE SURFACE OF THE TEST SPECIMEN (BACK OR FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE RESIDUAL CHARGE LEVEL ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY.

NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500 VOLTS YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A PERIOD OF 20 SECS. AT THE END OF THE 20 SECOND PERIOD, THE HIGH VOLTAGE (5000 VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS IMMEDIATELY GROUNDED. THE VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL BE PLOTTED ON THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL DISPLAY VOLTAGE AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT NECESSARY."

PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE SPECIMEN DID" IN ITS ENTIRETY.

PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND DECAY TIME TO 10% OF THE MAXIMUM VOLTAGE LEVEL ACHIEVED."

PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE: "REVERSE VOLTAGE POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS."

PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL BE INCLUDED FOR EACH OF THE WARP & FILLING DIRECTIONS, AS WELL AS THE OVERALL AVERAGE, FOR EACHFABRIC TESTED. THESE WILL BE OBTAINED BY AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS DOCUMENT, THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE MAXIMUM VOLTAGE IN BOTH THE WARP AND FILLING DIRECTIONS IS LESS THAN 4000 VOLTS, AND THE AVERAGE DECAY TIME (TO 10% MAXVOLTAGE) IS GREATER THAN 0.5 SECONDS IN BOTH THE WARP AND FILLING DIRECTIONS. IT SHALL BE INDICATED WHETHER THE FABRIC ISACCEPTABLE OR NON-ACCEPTABLE."

PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE WITH "406D".

AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY FOR THE TEST."

(Ref. T0215)

ADDITIONAL INFORMATION FOR V-B-871: NO ADDITIONAL INFORMATION FOLLOWS.

INTERIM SPECIFICATION CHANGES TO MIL-W-5664D:

PARA. 3.3.1 - DELETE IN ITS ENTIRETY AND SUBSTITUTE: "3.3.1 WEAVE CONSTRUCTION. THE WEAVE FOR ALL TYPES AND CLASSES MAY BE SUPPLIED IN EITHER SHUTTLE OR SHUTTLELESS LOOM CONSTRUCTION.

PARA. 3.7, SENTENCE 2, DELETE IN ITS ENTIRETY AND SUBSTITUTE "TYPE II SHALL BE CAMOUFLAGE GREEN 483.

PARA. 4.6.1.1 YARD-BY-YARD EXAMINATION, CONTINUED ON PAGE 6, LINE 2, DELETE "2.5" AND SUBSTITUTE "1.5.". LINE 3, DELETE "6.5" AND SUBSTITUTE "4.0"

TABLE II - DELETE THE DEFECT FOR "YARNS (FILLING)" ENTIRELY.

PARA. 4.6.3 - DELETE IN ITS ENTIRETY.

STANDARD SAMPLE FOR FOLIAGE GREEN 504, WEBBING, TEXTILE, ELASTIC, IS IDENTIFIED AS ROLL NO. 3743, REFERENCED FOR SHADE ONLY.

STANDARD SAMPLE FOR CAMOUFLAGE GREEN 483 IS IDENTIFIED AS ROLL NO. 3523, REFERENCED FOR SHADE ONLY.

ADDITIONAL INFO FOR A-A-1671B: NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T7239 - 9/11/06)

ADDITIONAL INFORMATION FOR MIL-B-81813:

WITH THE FOLLOWING INTERIM CHANGES:

PAGE 11, TABLE VI IN TEST METHOD COLUMN:

DELETE "5041 1/ 2/" AND SUBSTITUTE "5040 1/ 2/".

IN NUMBER OF DETERMINATIONS PER SAMPLE UNIT

COLUMN: DELETE "5".

IN RESULTS REPORTED AS COLUMN: DELETE "AVERAGE

OF 5 DETERMINATIONS TO NEAREST 0.1 OZ./SQ. YD."

PAGE 12, UNDER TABLE VI: DELETE FOOTNOTE 1/ AND

SUBSTITUTE: "1/ THE WEIGHT OF THE BATTING SHALL

BE DETERMINED IN ACCORDANCE WITH THE FULL WIDTH

SHORT-SPECIMEN METHOD OF METHOD 5040."

CHANGE TO AMENDMENT NO. 2:

PARA. 3.2.3, LINE 3: DELETE "OLIVE DRAB

S-1 (C.A. 66022)" AND SUBSTITUTE "CAMOUFLAGE

GREEN 483, MATCHING COLOR CHIP 34094 OF

FED-STD-595B".

PARA. 3.2.3, LINE 3: AFTER SAGE GREEN, DELETE

"1565" AND SUBSTITUTE "1590"

WHEN REQUIRED BY CONTRACT: ITERIM STANDARD FOR

FOLIAGE GREEN 504 IS IDENTIFIED AS ROLL #3721

AND IS REFERENCED FOR SHADE ONLY.

ADDITIONAL INFORMATION FOR MIL-C-43824A:

WHEN REQUIRED BY CONTRACT: INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS IDENTIFIED AS ROLL #3729, AND IS REFERENCED FOR SHADE ONLY.

PAGE 1, PARAGRAPH 1.1, SCOPE, LINE 3, DELETE "POLYESTER" AND SUBSTITUTE "WOOL".

PARAGRAPH 2.1, ISSUES OF DOCUMENTS UNDER SPECIFICATIONS, FEDERAL: DELETE "UU-P-268- PAPER, KRAFT, UNTREATED, WRAPPING."

PAGE 2, PARAGRAPH 2.2, OTHER PUBLICATIONS. LINE 3, DELETE EVERYTHING AFTER "SHALL APPLY:" AND SUBSTITUTE: "D 3992 - FINENESS OF WOOL TOP OR MOHAIR TOP AND ASSIGNMENTS OF GRADE"

PAGE 3, PARAGRAPH 3.3.2, MODACRYLIC. LINE 1: DELETE "40" AND SUBSTITUTE "15"

PAGE 3, PARAGRAPH 3.3.2, MODACRYLIC. LINE 2, DELETE "4-1/2" AND SUBSTITUTE "4"

PAGE 3, PARAGRAPH 3.3.3, POLYESTER. DELETE IN ITS ENTIRETY AND SUBSTITUTE: "3.3.3 WOOL. THE WOOL FIBER USED AS THE BASE FUR SHALL BE 60'S U.S. GRADE WOOL (24 MICRONS)."

ADD THE FOLLOWING NEW PARAGRAPH: "3.3.3.1 WOOL SHRINKAGE CONTROL TREATMENT. THE WOOL FIBERS SHALL BE TREATED WITH AN APPROVED SHRINKAGE CONTROL TREATMENT (SEE 6.8)."

PARAGRAPH 3.3.4 GUARD HAIR AND BASE FUR. LINE 4, DELETE "POLYESTER" AND SUBSTITUTE "WOOL".

PAGE 5, PARAGRAPH 4.4.2 TABLE II. COMPONENT TESTS UNDER "CHARACTERISTIC" COLUMN, LINE 4, DELETE "POLYESTER" AND SUBSTITUTE "WOOL".

PAGE 8, PARAGRAPH 4.7 TABLE IV. TEST METHODS ADD THE FOLLOWING:

"WOOL GRADE 3.3.3 ASTM D3993 1/

WOOL SHRINKAGE CONTROL TREATMENT 3.3.3.1 1/"

PAGE 9, PARAGRAPH 5.1.1 LEVEL A. LINE 9 AFTER "COTTON TAPE." DELETE THE REMAINDER OF THE PARAGRAPH AND SUBSTITUTE "EACH ROLL OF CLOTH SHALL BE ENCLOSED IN A POLYETHYLENE FILM TUBE WITH A MINIMUM THICKNESS OF 0.004 INCHES. THE TUBE SHALL BE CLOSED BY HEAT SEALING OR BY THE USE OF TIES."

PAGE 10, PARAGRAPH 5.2.1 LEVEL A. DELETE THE SECOND SENTENCE. PARA. 5.2.2 LEVEL B. DELETE THE SECOND SENTENCE. PARAGRAPH 5.2.2.1 DELETE IN ITS ENTIRETY.

PAGE 11, ADD THE FOLLOWING NEW PARAGRAPH: "6.8 APPROVED WOOL SHRINKAGE CONTROL TREATMENT. APPROVAL OF WOOL SHRINKAGE CONTROL TREATMENTS IS THE RESPONSIBILITY OF THE U.S. ARMY RESEARCH, DEVELOPMENT AND ENGINEERING CENTER, NATICK RESEARCH, DEVELOPMENT AND ENGINEERING CENTER, NATICK, MA 01760, AND IS BASED ON EXTENSIVE TESTS INCLUDING THOSE FOR TOXICITY WHICH ARE NOT SET FORTH IN THIS SPECIFICATION. BECAUSE OF TIME REQUIRED TO PERFORM A FULL EVALUATION, ONLY THOSE CHEMICAL TREATMENTS ALREADY APPROVED AND SO LISTED IN THE INVITATION FOR BIDS OR REQUESTS FOR PROPOSAL SHALL BE CONSIDERED ACCEPTABLE FOR THE RELATED PROCUREMENT."

INTERIM SPECIFICATION CHANGES TO AMENDMENT NO. 1: PAGE 1, PARAGRAPH 2.1, LINE 1. DELETE "PPP-P-1135" AND SUBSTITUTE "PPP-P-1133".

(ref. T1131 - 5/23/06)

ADDITIONAL INFO FOR MIL-P-15011: NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR MIL-C-6590:

AND THE FOLLOWING INTERIM CHANGES:

PAGE 2, PARAGRAPH 3.2.1, DELETE ENTIRELY AND SUBSTITUTE: "THE BACKING SHALL BE MADE FROM UNDYED, SPUN OR FILAMENT POLYPROPYLENE/COTTON YARN OF A SUITABLE SIZE FOR BACKING. POLYESTER YARN MAY BE USED AS AN ALTERNATE FOR THE POLYPROPYLENE YARN.".

PAGE 2, PARAGRAPH 3.3, DELETE ENTIRELY.

PAGE 4, AFTER PARAGRAPH 3.4.2, ADD NEW PARAGRAPH: "3.4.3 PH. THE PH VALUE OF THE FINISHED CLOTH SHALL BE NO LOWER THAN 5.5 NOR MORE THAN 8.5 WHEN TESTED AS SPECIFIED IN TABLE V."

PAGE 10, TABLE V, METHOD OF TESTING, ADD THE FOLLOWING BELOW "FLEXIBILITY" IN RESPECTIVE COLUMNS:

"PH 3.4.3 2811 3 .1 PH"

(ref. T0956 - 5/23/06)

ADDITIONAL INFORMATION FOR MIL-C-43774:

INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS

MIL-C-44436, ROLL #3729(THE FOLIAGE GREEN 502

AREA OF THE PATTERN), AND REFERENCED FOR SHADE

ONLY. THIS STANDARD IS TEMPORARY UNTIL FURTHER

NOTICE.

INTERIM SPECIFICATION CHANGES TO MIL-C-43774C:

PAGE 2, PARAGRAPH 2.1.1 SPECIFICATION, STANDARDS

AND HANDBOOKS. UNDER "SPECIFICATIONS, FEDERAL",

DELETE "PPP-P-1133- PACKAGING OF SYNTHETIC

FIBER FABRICS", AND SUBSTITUTE "FED-STD-802 -

PACKAGING OF SYNTHETIC FIBER FABRIC".

PAGE 3, PARAGRAPH 3.3.1, FIBER. DELETE IN ITS

ENTIRETY AND SUBSTITUTE THE FOLLOWING: "3.3.1

ARAMID FIBER BLEND. THE BLEND SHALL CONSIST OF

92 PERCENT META-ARAMID FIBER, 5 PERCENT PARA-

ARAMID FIBER AND 3 PERCENT CONDUCTIVE FIBER. THE

ARAMID FIBERS SHALL HAVE A NOMINAL DENIER OF 1.5

TO 1.7 DENIER PER FILAMENT, A STAPLE LENGTH OF

1-1/2 INCHES TO 2 INCHES, AND SHALL NOT CHAR AT

A TEMPERATURE LESS THAN 675 DEG. F. THE

CONDUCTIVE FIBER SHALL BE A NYLON SHEATHED

CARBON CORE FIBER AND SHALL BE 3 DENIER PER

FILAMENT, AND 1-1/2 T0 2 INCHES IN STAPLE LENGTH

(SEE 6.6)."

PAGE 3, TABLE I. PHYSICAL REQUIREMENTS.: UNDER

REQUIREMENT FOR "CHAR LENGTH, MAXIMUM AVERAGE

(INCHES)", DELETE "4.0" AND SUBSTITUTE "5.0".

PAGE 4, PARAGRAPH 3.6, FINISHING.: DELETE

PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE THE

FOLLOWING: "3.6, FINISHING. THE CLOTH SHALL BE

DESIZED, SCOURED AND HEAT SET."

PAGE 4, PARAGRAPH 3.6.1 ANTISTATIC FINISH.

DELETE IN ITS ENTIRETY AND SUBSTITUTE THE

FOLLOWING: "3.6.1 ELECTROSTATIC DECAY. THE

FINISHED CLOTH SHALL, WHEN CHARGED TOWARD

+5000 VOLTS AND -5000 VOLTS, REACH A MINIMUM

LEVEL OF +4000 AND -4000 VOLTS RESPECTIVELY AND

SHALL DISSIPATE 90 PERCENT OF THIS CHARGE IN

LESS THAN OR EQUAL TO 1/2 SECOND. THE AVERAGE

WARP RESULTS AND AVERAGE FILLING RESULTS SHALL

MEET THESE REQUIREMENTS BEFORE AND AFTER FIVE

LAUNDERINGS WHEN TESTED AS SPECIFIED IN 4.4.3."

PAGE 4, PARAGRAPH 3.6.2 NONFIBROUS MATERIAL.

DELETE IN ITS ENTIRETY.

PAGE 4, PARAGRAPH 3.7, LINE 2,: DELETE "5.0"

AND SUBSTITUTE "4.0".

PAGE 8, PARAGRAPH 4.4.3, END ITEM TESTING., LINE

2: DELETE SENTENCE STARTING WITH "THE SAMPLE

UNIT SHALL BE 1/4 YARD" IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING: "THE SAMPLE UNIT SHALL

BE 5 CONTINUOUS YARDS FULL WIDTH OF THE FINISHED

CLOTH."

PAGE 8, TABLE II, END ITEM TESTS. AFTER "LENGTH"

CHARACTERISTIC FOR STAPLE, ADD THE FOLLOWING

INFORMATION UNDER THE APPROPRIATE COLUMN:

"CONDUCTIVE FIBER 3.3.1 1/"

PAGE 8, TABLE II, END ITEM TESTS.: UNDER TEST

METHOD COLUMN AFTER "5560 3/" ADD "OR 4.5.3".

PAGE 8, TABLE II, END ITEM TESTS. DELETE

INFORMATION FOR ANTISTATIC FINISH BEFORE AND

AFTER FIVE LAUNDERINGS IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING UNDER THE

APPROPRIATE COLUMN:

"ELECTROSTATIC DECAY:

INITIAL 3.6.1 5931

AFTER 5 LAUNDERINGS 3.6.1 5556

. 6/AND

. 5931"

PAGE 9, TABLE II, END ITEM TESTS. DELETE ENTRY

FOR NONFIBROUS MATERIAL IN ITS ENTIRETY.

PAGE 9, TABLE II, END ITEM TESTS.: AT BOTTOM

OF TABLE, DELETE FOOTNOTE 5/ IN ITS ENTIRETY.

PAGE 9, PARAGRAPH 4.4.4, PACKAGING INSPECTION.,

LINE 3: DELETE "PPP-P-1133" AND SUBSTITUTE

"FED-STD-802".

PAGE 10: AFTER "PARAGRAPH 4.5.1 FABRIC BREAK

OPEN TEST." ADD THE FOLLOWING: "4.5.3

COLORFASTNESS TO LIGHT (XENON LAMP EXPOSURE).

THE FOLLOWING XENON COLORFASTNESS TO LIGHT TEST

METHOD MAY BE USED AS AN ALTERNATIVE TO METHOD

5660 OF FED-STD-191. THE TEST PROCEDURE SHALL

BE IN ACCORDANCE WITH AATCC METHOD 16 OPTION

E (WATER COOLED, CONTINUOUS LIGHT CYCLE) EXCEPT

THAT THE FOLLOWING DEVIATIONS SHALL APPLY:

A. THE TEST APPARATUS SHALL BE AN ATLS CI35 OR

CI65 WITH A THREE-TIERED INCLINED SPECIMEN RACK

OR AN ATLS C13000 FADEOMETER. THE APPARATUS

SHALL BE EQUIPPED WITH AN AUTOMATIC LIGHT

MONITOR AND SHALL BE CAPABLE OF AUTOMATICALLY

CONTROLLING IRRADIANCE, TEMPERATURE AND

HUMIDITY. THE APPARATUS SHALL BE MAINTAINED IN

ACCORDANCE WITH THE MANUFACTURER'S

RECOMMENDATIONS.

B. THE IRRADIANCE LEVEL SHALL BE 0.35+- 0.01

WATT/SQUARE METER/NANOMETER (W/M SQUARED/NM

BANDPASS AT 340 NANOMETERS.

C. THE GLASS FILTER COMBINATION SHALL BE A

BOROSILICATE TYPE "S" INNER AND OUTER FILTER.

D. THE RELATIVE HUMIDITY SHALL BE 50 +- 5

PERCENT DURING THE ENTIRE CYCLE. THE TEMPERATURE

CONTROL SET POINTS SHALL BE AS FOLLOWS: BLACK

PANEL" 63 DEG. +-2DEG C, CONDITIONING WATER:

50 DEG +- 2 DEG.C, AND DRY BULB: 45 +-3 DEG.C.

THE APPROXIMATE WET BULB DEPRESSION IS 10 DEG. C

(MAY NEED TO BE ADJUSTED TO ACHIEVE THE REQUIRED

RELATIVE HUMIDITY).

E. THE TEST SPECIMEN SHALL BE MOUNTED ON WHITE

CARDBOARD AND HALF MASKED (COVERED) WITH PAPER

APPROACHING ZERO LIGHT TRANSMITTANCE. THE TEST

SHALL BE CONTINUED UNTIL THE ENERGY EXPOSURE IS

EQUAL TO 20 KILOJOULES PER SQUARE METER.

NOTE: MONITORING OF THE DRY BULB TEMPERATURE,

WET BULB DEPRESSION IRRADIANCE AND BLACK PANEL

TEMPERATURE IS RECOMMENDED THROUGH THE USE OF

CHART RECORDERS. TO MINIMIZE TEST VARIATION,

INTERRUPTION OF THE TEST CYCLE (STOP AND GO)

SHOULD BE KEPT TO A MINIMUM."

0. PAGE 10, PARAGRAPH 5.1.1, LEVELS A AND

COMMERCIAL., LINE 2: DELETE "PPP-P-1133" AND

SUBSTITUTE "FED-STD-802".

P. PAGE 10, PARAGRAPH 5.2.1, LEVELS A, B AND

COMMERCIAL., LINE 2: DELETE "PPP-P-1133"

AND SUBSTITUTE "FED-STD-802".

Q. PAGE 10, PARAGRAPH 5.3, MARKING., LINE 3:

DELETE "PPP-P-1133" AND SUBSTITUTE

"FED-STD-802".

R. PAGE 11: DELETE PARAGRAPHS 6.6, 6.7, 6.7.1,

6.8 AND 6.9 AND SUBSTITUTE NEW PARAGRAPH 6.6

AS FOLLOWS: "6.6 MATERIAL. THE CLOTH HAS BEEN

SUCCESSFULLY MANUFACTURED WITH YARNS PRODUCED

FROM AN INTIMATE FIBER BLEND OF 92 PERCENT

NOMEX, 5 PERCENT KEVLAR AND 3 PERCENT

P-140. THE FIBER BLEND IS AVAILABLE IN BALE

FORM FROM E.I. DUPONT DE NEMOURS & CO., INC.,

WILMINGTON, DE. 19880."

ADDITIONAL INFORMATION FOR PPP-T-45:

PPP-T-45 IS CANCELLED AND SUPERSEDED BY A-A-1671: TAPE, GUMMED

(PAPER, REINFORCED, LAMINATED)

NOTE: A-A-1671 IS WRITTEN TO BE APPLIED TO PPP-T-45'S REQUIREMENTS OF TYPE III, CLASS B.

(ref. T0592 - 9/11/06)

INTERIM CHANGES TO A-A-55126B,

THE FOLLOWING CHANGES ARE FOR ALL CURRENT, PENDING AND FUTURE PROCUREMENTS OF THE SUBJECT DOCUMENT UNTIL SUCH TIME AS THE DOCUMENT IS AMENDED OR REVISED.

PAGE 4. TABLE I, PHYSICAL REQUIREMENTS, CHARACTERISTIC, SHEAR STRENGTH,DELETE LBS/SQ INCH (MIN), ADD SHEAR STRENGTH, LBS/2 SQ INCH (MIN).

PAGE 5 TABLE II, PHYSICAL REQUIREMENTS; CHARACTERISTIC, LENGTH

DIMENSIONAL STABILITY, % (MAX); LOOP, ALL CLASSES DELETE .0; ADD ALL CLASSES 4.0.

PAGE 7, Paragraph 3.10.2, Change the following title of paragraph from: "Fray resistance of Universal Camouflage Shades" and replace with "Fray resistance of Camouflage Prints"

PAGE 14, Paragraph 7.3.4 Change the following title of paragraph from: Fray resistance for Universal Camouflage Shades." and replace with "Fray resistance for Camouflage Prints."

ADDITIONAL INFORMATION FOR A-A-55195:

INTERIM STANDARD FOR FOLIAGE GREEN 504 IS

IDENTIFIED AS ROLL #3721, AND IS REFERENCED

FOR SHADE ONLY.

ADDITIONAL INFORMATION FOR MIL-C-83450:

INTERIM SPECIFICATION CHANGES TO MIL-C-83450A:

PAGE 2, PARA. 3.2.2, LINE 3, DELETE "OR META-

ARAMID AND NOVOLOID".

ADDITIONAL INFO FOR FED-STD-4 GLOSSARY OF FABRIC IMPERFECTIONS:

REVISION B: 7/29/64; AMENDMENT 2: 9/12/75

NOTICE 1, DATED 10/1/87.

DEV. TO FED. STD. 4B & AM. 2, PAGE 2, SEC.I. PARA. 2.1. IN IMPERFECTION

COMMERCIAL TERMINOLOGY AND GLOSSARY NO. COLUMNS, AFTER SHADE

BAR - 14 INSERT: "SHADED CLOTH-61B".

PAGE 8 PARA. 3.4, GLOSSARY NO. "61A- OFF SHADE", IN "DEFINITION" COLUMN,

DELETE ":SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END". ADD NEW

GLOSSARY NO. "SHADED CLOTH "61B-SHADED CLOTH (SHADED SIDE TO SIDE, SIDE

TO CENTER OR END TO END) WITH THE FOLLOWING DEFINITION: "COLOR

DIFFERENCE BETWEEN THE RESPECTIVE CLOTH AREAS".

PAGE 22, SECTION III, PARAGRAPH 2.1, IN "IMPERFECTION COMMERCIAL

TERMINOLOGY" AND GLOSSARY NO." COLUMNS, AFTER "SHADE BAR-15" INSERT:

"SHADED CLOTH - 62A"

PAGE 27, PARAGRAPH 3.4, GLOSSARY NO. "62-OFF SHADE" IN "DEFINITION"

COLUMN DELETE: "SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END".

ADD NEW GLOSSARY NO, "62A-SHADED CLOTH (SHADED SIDE TO SIDE, SIDE TO

CENTER OR END TO END)" WITH THE FOLLOWING DEFINITION: "COLOR DIFFERENCE

BETWEEN THE RESPECTIVE CLOTH AREAS."

DEVIATION FROM FED. STD. 4B, AND AMEND 2:

PG 2, SECTION 1, PARA.2.1, IN "IMPERFECTION COMMERCIAL TERMINOLOGY" AND

"GLOSSARY NUMBER" COLUMNS, AFTER "SHADE BAR-14",INSERT: "SHADED CLOTH

61B".

PG 8, PARA.3.4, GLOSSARY NUMBER "61A-OFF SHADE" IN "DEFINITION" COLUMN,

DELETE, "SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END". ADD NEW

GLOSSARY NO."61B SHADED CLOTH "SHADED SIDE TO SIDE, SIDE TO CENTER OR

END TO END" WITH THE FOLLOWING DEFINITION; "COLOR DIFFERENCE BETWEEN THE

RESPECTIVE CLOTH AREAS."

PAGE 22, SECTION III, PARAGRAPH 2.1, IN "IMPERFECTION COMMERCIAL

TERMINOLOGY" AN GLOSSARY NO." COLUMNS, AFTER "SHADE BAR-15"

INSERT: "SHADED CLOTH - 62A"

PAGE 27, PARAGRAPH 3.4, GLOSSARY NO "62-OFF SHADE" IN "DEFINITION"

COLUMN DELETE: "SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END".

ADD NEW GLOSSARY NO, "62A-SHADED CLOTH (SHADED SIDE TO SIDE, SIDE TO

CENTER OR END TO END)" WITH THE FOLLOWING DEFINITION: "COLOR DIFFERENCE

BETWEEN THE RESPECTIVE CLOTH AREAS."

Ref. T0202 - 04/04/07)

ADDITIONAL INFORMATION: FED-STD-751 HAS BEEN

CANCELLED AND REPLACED BY ASTM-D-6193, 4/98

STANDARD PRACTICES FOR STITCHES AND SEAMS.

THIS STANDARD SHOULD BE USED IN PREFERENCE

TO FED-STD-751.

(ref. T0216 - May 18, 2006)

INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2 STANDARD INSPECTION.

ADDITIONAL INFORMATION FOR MIL-STD-105E:

MIL-STD-105E, dated 10 May 1989, is hereby canceled.

Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes."

Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document.

(Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.)

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)

SECTION D – PACKAGING AND MARKING

JACKET, FLYER’S, CWU-45/P CASE LOT QUANTITY 12 OF ONE SIZE AND COLOR SHALL BE PACKED IN EACH SHIPPING CARTON.

JACKET, FLYER’S, CWU-36/P CASE LOT QUANTITY 16 JACKET OF ONE SIZE AND COLOR SHALL BE PACKED IN EACH SHIPPING CARTON.

EACH JACKET SHALL BE PACKED WITH TAGS/LABELS CLEARLY VISABLE AND HEAT- SEALED IN A CLEAR POLY BAG.

AS A MINIMUM ITEMS SHALL BE PACKED IN A SNUG FITTING FIBERBOARD SHIPPING CONTAINER CONFORMING TO ASTM-D-5118 TYPE CF, STYLE RSC, VARIETY SW,CLASS DOMESTIC, WITH A DOUBLE WALL LINER. ANY COMMERCIAL CLOSURE METHOD CITED IN ASTM-D-1974 IS ACCEPTABLE EXCEPT STAPLING.

PACKAGING SHALL BE AS PER ASTM-D-3951, MIL-STD-129 AND MIL-STD-147. LOT NUMBERING SHALL BE IN ACCORDANCE WITH MIL-STD-129 AND DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements dated October 2018, which has superseded DSCPM 4155.3, QUALITY SYSTEMS REQUIREMENTS, dated NOVEMBER 3, 1997.

PRESERVATION/PACKAGING SHALL BE IN ACCORDANCE WITH ASTM-D3951-90.

MIL-STD-129R - DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED 18 FEBRUARY 2014

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E

w/CHANGE 1 23 December 2013

SUPERSEDING

MIL-STD-147E

16 May 2008

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

Packaging examination. The fully packaged end item shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.

Examine Defect

Marking Omitted; incorrect; illegible, of (exterior) improper size, location, sequence & Unit Pack, or method of application.

Materials Any component missing, damaged or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling. Bulged or distorted container.

Contents Number of intermediate containers per shipping container is more or less than required.

Number of items per container is more or less than required.

Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged.

The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5.

Examine Defect

Finished Length, width or height exceeds Dimensions specified maximum requirement.

Palleti- Pallet pattern not as specified.

zation Interlocking of loads not as specified. Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted; incorrect; illegible;

of improper size, location, sequence or method of appli-cation.