PGC03098-POT.txt

GLOVE, INSERT, COLD WEATHER, TYPE I OR II,

CLASS 3, FOLIAGE GREEN 504

SHALL BE MADE IN ACCORDANCE WITH A-A-55119

DATED 23 MARCH 1993.

STANDARD SAMPLE FOR FOLIAGE GREEN 504:

STANDARD SAMPLE FOR CLOTH, UNIVERSAL CAMOUFLAGE

PATTERN, WIND RESISTANT POPLIN, NYLON/COTTON BLEND,

CONFORMING TO CLASS 8 (WRINKLE FREE) OF MIL-DTL-44436

IS AVAILABLE ON ROLL NO. 3729 AND IS APPLICABLE FOR

SHADE ONLY.

AS AN ALTERNATE COLOR CHIP NUMBER 24165 OF FED-STD-595C

CAN ALSO BE USED FOR SHADE ONLY. COLOR CHIPS CAN BE

ORDERED FROM THE FOLLOWING:

GSA Property Management

GSA/C0/3QSCB

490 L'Enfant Plaza East S.W Suite 8214 Washington, D.C. 20407

INTERIM CHANGES TO A-A-55119 ARE AS FOLLOWS:

PAGE 1, UNDER "CLASSIFICATION" AFTER "CLASS 2"

ADD "CLASS 3 - FOLIAGE GREEN 504".

PAGE 2, "YARN.", DELETE PARAGRAPH IN ITS

ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:

"YARN. THE YEARN SHALL BE A 100 WORSTED WOOL,

LONG STABLE 2 PLY YARN. THE 100% WORSTED WOOL

SHALL CONSIST OF FLEECE OR PULLED WOOL OR A

COMBINATION OF FLEECE AND PULLED WOOL OF NOT LOWER

THAN 45'S U.S STANDARD. THE USE OF REPROCESSED, REUSED

OR WASTE WOOL IS PROHIBITED. THE WOOL SHALL BE

TREATED FOR MOTHPROOFING."

PAGE 2, TABLE I: DELETE TITLE AND SUBSTITUTE

WITH "WOOL-NYLON BLEND YARN COUNTS & TURNS".

UNDER TABLE 1, FOR "TYPE I, UNDER "HAND, FINGERS, AND

THUMB", AND UNDER "CUFF". ALSO UNDER "TYPE II" ADD:

"2 ends of 2/14.5 OR 2 ENDS OF 2/18. ".

PAGE 2, DELETE "WOOL" PARAGRAPH IN IT'S ENTIRETY.

PAGE 2, DELETE "NYLON" PARAGRAPH IN IT'S ENTIRETY.

PAGE 3, DELETE "FIBER CONTENT" PARAGRAPH IN IT'S

ENTIRETY.

PAGE 3, COLOR: AFTER "CAMOUFLAGE GREEN 483" FOR

"CLASS 1; BLACK 357, SHADE 37030 FOR CLASS

2 AND FOLIAGE GREEN 504 FOR CLASS 3".

PAGE 3, "THREAD" PARAGRAPH: DELETE LAST SENTENCE

& SUBSTITUTE: "THE SAME YARN USED TO KNIT THE

INSERTS, EXCEPT THAT IT WILL BE 1 END OF SINGLES

15'S WOOL/NYLON BLEND WHEN WOOL/NYLON BLENDED

YARN IS USED IN THE BODY OF THE INSERT, OR 1 END

OF 2/24 OR 2/23 ACRYLIC HOMOFIBER WHEN ACRYLIC

HOMOFIBER IS USED IN THE BODY OF THE INSERT,

SHALL, SHALL BE USED IN THE OTHER LOOPER SO THAT

THE YARN IS AT THE OUTSIDE EDGE OF THE CUFF."

PAGE 3, "COLOR", LINE 2 AFTER "CAMOUFLAGE GREEN 483"

ADD "FOR "CLASS 1; BLACK 357, SHADE 37030 FOR CLASS

2 AND FOLIAGE GREEN 504 FOR CLASS 3".

PAGE 3, "COLOR" LINE 3, DELETE "MEDIUM GRAY AV

C.A. 66062" AND SUBSTITUTE WITH "BLACK 357 FOR THE

CLASS 2 GLOVE INSERT AND FOLIAGE GREEN 504 FOR THE

CLASS 3 GLOVE INSERT".

PAGE 3, COLORFASTNESS, DELETE PARAGRAPH AND

SUBSTITUTE: "THE DYED GLOVE INSERTS SHALL SHOW

FASTNESS TO LAUNDERING, PERSPIRATION AND

CROCKING EQUAL TO OR BETTER THAN THE FOLLOWING

RATINGS WHEN TESTED AS SPECIFIED:

LAUNDERING - AATCC 61, TEST 1A, MINIMUM RATING

OF "GOOD" OR "3 - 4" USING GRAY SCALE FOR COLOR

CHANGE AND STAINING, AFTER 3 CYCLES.

PERSPIRATION - AATCC 15, ALKALINE AND ACID,

MINIMUM RATING FOR BOTH ALKALINE AND ACID OF

"GOOD" OR "4.0" USING GRAY SCALE COLOR CHANGE

AND TRANSFER.

CROCKING - AATCC 8-1996, COLORFASTNESS TO

CROCKING, CROCKMETER METHOD, USING GRAY SCALE

FOR COLOR SCALE FOR COLOR STAINING: RATING OF

3.0 MINIMUM DRY; RATING OF 3.0 MINIMUM WET".

PAGE 3, ELASTIC YARN (FOR TYPE II), AFTER FIRST

SENTENCE, ADD THE FOLLOWING NEW SENTENCE: "AS

AN ALTERNATE, A RUBBER CORE ELASTIC MAY REPLACE

THE SPANDEX 210 DENIER (NOMINAL SIZE), THE COLOR

OF THE RUBBER CORE SHALL APPROXIMATE THE COLOR

OF THE END ITEM GLOVE".

PAGE 3, UNDER "ELASTIC YARN (FOR TYPE II)" LINE 5,

AFTER "CAMOUFLAGE GREEN 483" DELETE "GRAY 1155" AND

SUBSTITUTE WITH "BLACK 357 FOR THE CLASS 2 GLOVE

AND FOLIAGE GREEN 504 FOR THE CLASS 3 GLOVE".

PAGE 4, "LABEL/MARKING" PARAGRAPH, LINE 3, AFTER

"FOR HANDWEAR", ADD: ";OR HEAT SENSITIVE LABEL

WITH A COMBINED "IDENTIFICATION, SIZE AND

INSTRUCTION LABEL".

PAGE 4, "INSTRUCTION LABEL" PARAGRAPH, LINE 1,

DELETE: "A" AND SUBSTITUTE THE FOLLOWING: "WHEN

USING A HEAT TRANSFER COMBINATION IDENTIFICATION

AND SIZE LABEL, A".

PAGE 4, UNDER "INSTRUCTION LABEL" PARAGRAPH, ADD

THE FOLLOWING PARAGRAPH:

"COMBINATION IDENTIFICATION, SIZE AND

INSTRUCTION LABEL (CLASS 1, CLASS 2 AND CLASS 3).

NOTE: WHEN THESE LABELS ARE USED ON CLASS 2 AND

CLASS 3 INSERTS, THE LABEL SHALL BE APPLIED ON

THE OUTSIDE OF THE INSERT. THE LABELS SHALL NOT

BE GREATER THAN 2-1/4 BY 1-3/4 INCHES IN

DIMENSION. THE LABEL SHALL BE POSITIONED 1/2

PLUS OR MINUS 1/16 INCH DOWN FROM THE INSIDE EDGE

OF THE RIBBED CUFF ON ONE SIDE. THE LABEL COLOR

SHALL MATCH THE GLOVE INSERT COLOR. THE SIZE

NUMERALS SHALL BE IN BOLD A NOMINAL 1/4 INCH IN

HEIGHT. THE NOMENCLATURE, TYPE AND CLASS,

CONTRACT NUMBER, AND CONTRACTOR NAME SHALL BE IN

ALL CAPITAL LETTERS. THE FOLLOWING INFORMATION

SHALL BE ON THIS LABEL:

SIZE

NOMENCLATURE

TYPE AND CLASS

CONTRACT NUMBER

CONTRACTOR NAME

NSN

FIBER CONTENT

INSTRUCTIONS: WEAR GLOVE INSERT

INSIDE OF GLOVE SHELLS. USE THE SAME

GLOVE INSERT SIZE AS THE LEATHER SHELL.

ALTERNATE INSERTS BETWEEN LEFT AND

RIGHT HANDS TO INCREASE WEAR LIFE.

WASH IN LUKE WARM OR COLD WATER.

DRY INSERTS SLOWLY."

PAGE 4, AFTER "INSTRUCTION LABEL" PARAGRAPH, AND

BEFORE "SIZES AND MEASUREMENTS" PARAGRAPH,

ADD THE FOLLOWING PARAGRAPH:"BAR CODE LABEL/TAG.

EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH

A TYPE VIII, CLASS 17, LABEL/TAG OF DDD-L-20.

THE LABEL/TAG SHALL BE LOCATED SO THAT IT IS

COMPLETELY VISIBLE ON ON THE ITEM WHEN IT IS

FOLDED AND/OR PACKAGED AS SPECIFIED AND SHALL

CAUSE NO DAMAGE TO THE ITEM."

PAGE 8, TABLE III, UNDER WEIGHT/DOZEN: DELETE

"19,21,24,26,28" AND REPLACE WITH

"18,19,21,22,25" RESPECTIVELY.

PAGE 11, UNDER "DEFECTS", LINE 13, AFTER

"LABEL OMITTED", ADD: ", SEPARATING FROM GLOVE

INSERT,".

PAGE 11, "DEFECTS" PARAGRAPH, LINE 18, AFTER

"OVERLAPPED." ADD THE FOLLOWING: "BAR CODE

OMITTED OR NOT READABLE BY SCANNER, HUMAN-

READABLE INTERPRETATION (HRI) OMITTED OR

ILLEGIBLE, NOT VISIBLE ON FOLDED, PACKAGED ITEM,

CAUSES DAMAGE TO THE ITEM."

PAGE 12, DELETE "PACKAGING EXAMINATION"

PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE THE

FOLLOWING PARAGRAPH:

Packaging examination. The fully packaged end item shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.

Examine Defect

Marking (exterior Omitted; incorrect; illegible, of improper and interior) size, location, sequence, or method of application.

Materials Any component missing, damaged or not as specified.

Workmanship Inadequate application of components such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling.

Bulged or distorted container.

Contents Number of intermediate containers per shipping container is more or less than required.

Number of items per container is more or less than required.

Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged.

The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5.

Examine Defect

Finished dimension Length, width or height exceeds specified maximum requirement.

Palletization Interlocking of loads not as specified.

Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted; incorrect; illegible; of improper size, location, sequence or method of application.

PAGE 12, END ITEM PERFORMANCE TESTING, DELETE

PARAGRAPH IN ITS ENTIRETY.

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-

20" AND REPLACE "MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR A-A-50199A -

PAGE 2, DELETE SECTION 4 IN ITS ENTIRETY AND SUBSTITUTE:

"4. PRESERVATION, PACKING AND MARKING.

4.1 PRESERVATION, PACKING AND MARKING SHALL BE SPECIFIED IN THE CONTRACT

OR ORDER. (SEE 5.2)."

PAGE 3,

PARAGRAPH 5.2 ADD "e. PACKAGING REQUIREMENTS (SEE 4.1

PARAGRAPH 5.3, AFTER LINE 2,

DELETE REMAINDER AND SUBSTITU)TE: "AVAILABLE ONLINE AT

http://assist.daps,dla.mil".

(Ref. 91039 - 01/24/07)

ADDITIONAL INFORMATION FOR MIL-T-43624:

STANDARD SAMPLE FOR CAMOUFLAGE GREEN 483 IS

IDENTIFIED AS ROLL NO. 3523, REFERENCED FOR

SHADE ONLY.

STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS

MIL-C-44436, ROLL #3729 (THE FOLIAGE GREEN 502

AREA OF THE PATTERN), AND REFERENCED FOR SHADE

ONLY.

ADDITIONAL INFORMATION FOR FED-STD-191:

FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW

DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO END ITEM

SPECIFICATION FOR REPLACEMENT ASTM.

INTERIM CHANGES TO FED-STD-191A:

TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE

SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE

OF THE VISE, SUCH THAT ONE INCH OF SPECIMEN LIES WITHIN THE CLAMP AND

ONE INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF

THE VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL

PLATE".

TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA

4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91".

THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING

SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540,

AND 1550. PARA 5.1 OF THESE TEST METHODS REQUIRE THE USE OF 1,1,1-

TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-TRICHLORETHANE IS AN OZONE

DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE

USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN

BASIC OR ANY REFERENCED DOCUMENT.

METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD.

PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE

FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH

THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE

CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION

(INNER FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF

THE DIAL PLATE."

METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5,

PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND

BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE

SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND

PLACED IN A PRE-HEATED DRYER HAVING A STACK TEMPERATURE OF 140-180 DEG.

F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE

TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60

MINUTES OR UNTILSAMPLES ARE DRY IN A ROTATING TUMBLE DRYER."

PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE

SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING:

"THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND

PLACED IN A PRE-HEATED DRYER HAVING A STACKTEMPERATURE OF 140-180 DEG.

F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE

TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40

MINUTES OR UNTIL SAMPLES ARE DRY."

METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1,

PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1,

PARA. 4: DELETE "APPARTUS" AND SUBSTITUTE "APPARATUS". PAGE 1, PARA.

5.1, LINE 3: AFTER "AT" DELETE"APPROXIMATELY".

PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6: AFTER

"TO" ADD "+-".

PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE

FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING

IT OVER THE SENSOR OPENING. THE SURFACE OF THE TEST SPECIMEN (BACK OR

FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE RESIDUAL CHARGE

LEVEL ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY.

NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500

VOLTS YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A

PERIOD OF 20 SECS. AT THE END OF THE 20 SECOND PERIOD, THE HIGH VOLTAGE

(5000 VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS IMMEDIATELY GROUNDED.

THE VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL BE

PLOTTED ON THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL

DISPLAY VOLTAGE AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT

NECESSARY."

PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE

SPECIMEN DID" IN ITS ENTIRETY.

PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH

THE FOLLOWING: "RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND

DECAY TIME TO 10% OF THE MAXIMUM VOLTAGE LEVEL ACHIEVED."

PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE:

"REVERSE VOLTAGE POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS."

PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH

THE FOLLOWING: "THE AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL

BE INCLUDED FOR EACH OF THE WARP & FILLING DIRECTIONS, AS WELL AS THE

OVERALL AVERAGE, FOR EACHFABRIC TESTED. THESE WILL BE OBTAINED BY

AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH

VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS

DOCUMENT, THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE

MAXIMUM VOLTAGE IN BOTH THE WARP AND FILLING DIRECTIONS IS LESS THAN

4000 VOLTS, AND THE AVERAGE DECAY TIME (TO 10% MAXVOLTAGE) IS GREATER

THAN 0.5 SECONDS IN BOTH THE WARP AND FILLING DIRECTIONS. IT SHALL BE

INDICATED WHETHER THE FABRIC ISACCEPTABLE OR NON-ACCEPTABLE."

PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE

WITH "406D".

AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC

DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY

FOR THE TEST."

(Ref. T0215)

MIL-STD-129 CURRENT REVISION UNLESS OTHERWISE SPECIFIED

- DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE

MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA

TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING

CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS

OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER

TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE

STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)